Adsorption of Patent Blue V from Textile Industry Wastewater Using Sterculia alata Fruit Shell Biochar: Evaluation of Efficiency and Mechanisms

Water ◽  
2020 ◽  
Vol 12 (7) ◽  
pp. 2017
Author(s):  
Balendu Shekher Giri ◽  
Mandavi Goswami ◽  
Prabhat Kumar ◽  
Rahul Yadav ◽  
Neha Sharma ◽  
...  
Keyword(s):  
Textile Industry ◽  
Contact Time ◽  
Dye Removal ◽  
Adsorption Process ◽  
Physical Nature ◽  
Freundlich Isotherm ◽  
Maximum Adsorption Capacity ◽  
Electron Microscopic ◽  
Sem Images ◽  
Patent Blue

Biochar prepared from Sterculia alata fruit shell showed a better performance for dye removal than the biomass from Sterculia alata fruit shell. The important process parameters—namely the pH, the amount of biochar, the initial dye concentration and the contact time—were optimized in order to maximize dye removal using biochar of Sterculia alata fruit shell as the bio-sorbent. The results from this study showed that the maximum adsorption of dye on the biochar was obtained at a biochar dosage of 40 g/L, at a contact time of 5 h, and an initial dye concentration of 500 mg/L (pH 2.0; temperature 30 ± 5 °C). The increase in the rate adsorption with temperature and the scanning electron microscopic (SEM) images indicated the possibility of multilayer type adsorption which was confirmed by better fit of the Freundlich adsorption isotherm with the experimental data as compared to the Langmuir isotherm. The values n and R2 in the Freundlich isotherm were found to be 4.55 and 0.97, respectively. The maximum adsorption capacity was found to be 11.36 mg/g. The value of n > 1 indicated physical nature of the adsorption process. The first and second order kinetics were tested, and it was observed that the adsorption process followed the first-order kinetics (R2 = 0.911).

scholarly journals Langmuir and Freundlich isotherm equation test on the adsorption process of Cu (II) metal ions by cassava peel waste (Manihot esculenta crantz)

2021 ◽  
Vol 2126 (1) ◽  
pp. 012022
Author(s):  
S Nuryanti ◽  
Suherman ◽  
S Rahmawati ◽  
M Amalia ◽  
T Santoso ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Manihot Esculenta ◽  
Contact Time ◽  
Adsorption Process ◽  
Freundlich Isotherm ◽  
Maximum Adsorption Capacity ◽  
Manihot Esculenta Crantz ◽  
Isotherm Equations ◽  
Cassava Peel

Abstract This Study aims to determine the adsorption process of Cu (II) metal by cassava peel waste (Manihot esculenta crantz) meeting the Langmuir equation and Freundlich. Research method cassava peel made into activated carbon, then determine the mass, pH and optimum contact time. Then the determination of the maximum adsorption capacity was carried out by testing with the Langmuir isotherm and Freundlich isotherm equations. The results showed that the best conditions (optimal conditions) were obtained with the addition of 0.5 grams of active carbs from cassava peels. The percentage of Cu ion adsorption in these conditions was 97.72%, at pH 6 and a contact time of 60 minutes and the absorption capacity was 98.49%. The maximum adsorption capacity of cassava peel activated carbon to Cu(II) ions at the optimum condition was determined based on the Langmuir and Freundlich isotherm equations. The results obtained were-51.813 mg/g and 26,792 mg/g, respectively.

scholarly journals Characterization and application of orange peel as an adsorbent for cationic dye removal from aqueous solution

2021 ◽  
Vol 25 ◽  
pp. e16
Author(s):  
Aline Haas ◽  
Eliane Pereira dos Santos
Keyword(s):  
Methylene Blue ◽  
Dye Removal ◽  
Adsorption Process ◽  
Solid Medium ◽  
Orange Peel ◽  
Freundlich Isotherm ◽  
Adsorptive Capacity ◽  
Blue Dye ◽  
Maximum Adsorption Capacity ◽  
Methylene Blue Dye

 With the great generation of colored effluents, several methods for the removal of the color are used, being one of them the method of adsorption in solid medium. In this paper, the in natura orange peel was used as the alternative biomass for the adsorption process of methylene blue, which was characterized by moisture content, pH, apparent density, iodine number, and methylene blue index. To determine the adsorptive capacity of the methylene blue dye, pH 7 was obtained as favorable, the adsorption process showed an adsorption of 82% of the methylene blue dye and a 10 min equilibrium time, where the Freundlich isotherm presented a better adaptation to the adsorption process in orange peel, with its maximum adsorption capacity of 3.9630 mg g-1, for the methylene blue dye. 

scholarly journals Castor Leaves-Based Biochar for Adsorption of Safranin from Textile Wastewater

2021 ◽  
Vol 13 (12) ◽  
pp. 6926
Author(s):  
Muhammad Suleman ◽  
Muhammad Zafar ◽  
Ashfaq Ahmed ◽  
Muhammad Usman Rashid ◽  
Sadiq Hussain ◽  
...  
Keyword(s):  
Contact Time ◽  
Dye Removal ◽  
Adsorption Process ◽  
Research Work ◽  
Freundlich Isotherm ◽  
Textile Wastewater ◽  
Isotherm Model ◽  
Textile Dye ◽  
Order Kinetic ◽  
Surface Areas

The prospect of synthesizing biochar from agricultural wastes or by-products to utilize them as a promising adsorbent material is increasingly gaining attention. This research work focuses on synthesizing biochar from castor biomass (CBM) and evaluating its potential as an adsorbent material. Castor biomass-based biochar (CBCs) prepared by the slow pyrolysis process at different temperatures (CBC400 °C, CBC500 °C, and CBC600 °C for 1 h) was investigated for the adsorption of textile dye effluents (safranin). The pyrolysis temperature played a key role in enhancing the morphology, and the crystallinity of the biochar which are beneficial for the uptake of safranin. The CBC600 adsorbent showed a higher safranin dye removal (99.60%) and adsorption capacity (4.98 mg/g) than CBC500 (90.50% and 4.52 mg/g), CBC400 (83.90% and 4.20 mg/g), and castor biomass (CBM) (64.40% and 3.22 mg/g). Adsorption data fitted better to the Langmuir isotherm model than to the Freundlich isotherm model. The kinetics of the adsorption process was described well using the pseudo-second-order kinetic model. The study on the effect of the contact time for the adsorption process indicated that for CBC600, 80% dye removal occurred in the first 15 min of the contact time. After three regeneration cycles, CBC600 exhibited the highest dye removal efficiency (64.10%), highlighting the enhanced reusability of CBCs. The crystalline patterns, functional binding sites, and surface areas of the prepared CBCs (CBC400, CBC500, CBC600) were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and Brunauer–Emmett–Teller surface area measurements, respectively.

scholarly journals Full Factorial Design for Gold Recovery from Industrial Solutions

Toxics ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 111
Author(s):  
Maria Mihăilescu ◽  
Adina Negrea ◽  
Mihaela Ciopec ◽  
Petru Negrea ◽  
Narcis Duțeanu ◽  
...  
Keyword(s):  
Factorial Design ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Adsorption Process ◽  
Design Method ◽  
Precious Metals ◽  
Gold Recovery ◽  
Maximum Adsorption Capacity ◽  
Gold Concentration ◽  
Commercial Resin

Gold is one of the precious metals with multiple uses, whose deposits are much smaller than the global production needs. Therefore, extracting maximum gold quantities from industrial diluted solutions is a must. Am-L-GA is a new material, obtained by an Amberlite XAD7-type commercial resin, functionalized through saturation with L-glutamic acid, whose adsorption capacity has been proved to be higher than those of other materials utilized for gold adsorption. In this context, this article presents the results of a factorial design experiment for optimizing the gold recovery from residual solutions resulting from the electronics industry using Am-L-GA. Firstly, the material was characterized using atomic force microscopy (AFM), to emphasize the material’s characteristics, essential for the adsorption quality. Then, the study showed that among the parameters taken into account in the analysis (pH, temperature, initial gold concentration, and contact time), the initial gold concentration in the solution plays a determinant role in the removal process and the contact time has a slightly positive effect, whereas the pH and temperature do not influence the adsorption capacity. The maximum adsorption capacity of 29.27 mg/L was obtained by optimizing the adsorption process, with the control factors having the following values: contact time ~106 min, initial Au(III) concentration of ~164 mg/L, pH = 4, and temperature of 25 °C. It is highlighted that the factorial design method is an excellent instrument to determine the effects of different factors influencing the adsorption process. The method can be applied for any adsorption process if it is necessary to reduce the number of experiments, to diminish the resources or time consumption, or for expanding the investigation domain above the experimental limits.

scholarly journals STUDI KINETIKA ADSORPSI Pb MENGGUNAKAN ARANG AKTIF DARI KULIT PISANG

Konversi ◽  
2015 ◽  
Vol 4 (1) ◽  
pp. 17
Author(s):  
Ari Susandy Sanjaya ◽  
Rizcy Paramita Agustine
Keyword(s):  
Adsorption Process ◽  
Freundlich Isotherm ◽  
Langmuir Equation ◽  
Kinetics Model ◽  
Banana Peel ◽  
Maximum Adsorption Capacity ◽  
Kinetics Analysis ◽  
Optimum Time ◽  
Lead Metal ◽  
Isotherm Equations

Abstrak- Logam Pb merupakan salah satu pencemar lingkungan dan dapat mengakibatkan kematian atau gangguan kesehatan dalam waktu singkat. Salah satu cara untuk mengatasi masalah pencemaran Pb adalah dengan menggunakan arang aktif dari kulit pisang. Penelitian ini bertujuan untuk menentukan model kinetika yang sesuai pada proses adsorpsi Pb dengan melihat daya jerap arang aktif kulit pisang dalam berbagai variasi massa (1 g; 1,5g dan 2 g) dan waktu kontak (20 menit, 40 menit dan 60 menit). Analisa Kinetika didasarkan pada kinetika orde nol, orde satu dan orde dua serta menentukan kapasitas maksimum adsorpsi arang atif kulit pisang  terhadap logam Pb. Persamaan yang digunakan dalam proses adsorpsi adalah persamaan adsorpsi Isoterm Langmuir dan Freundlich. Dari hasil analisa, waktu optimum adsorbsi terjadi pada waktu 60 menit.  Kinetika adsorbsi logam Pb dengan arang aktif dari kulit pisang pada massa 1 dan 2 g mengikuti model kinetika orde 2, sedangkan pada massa 1,5 g mengikuti kinetika orde 0. Persamaan adsorpsi Langmuir lebih sesuai untuk isotherm adsorpsi pada penelitian ini. Adsorpsi Pb oleh kulit pisang yang sesuai dengan pola isotherm adsorpsi Langmuir mengindikasikan bahwa adsorpsi hanya berlangsung satu lapis (monolayer). Kapasitas adsorpsi maksimum ditunjukkan oleh nilai a yang besar, yaitu 1,4582 pada massa 1 g sedangkan kekuatan interaksi antara ion Pb2+ dengan kulit pisang terjadi pada massa 2 g yang ditunjukkan dengan nilai kL yang besarnya 0,409 Kata kunci : kinetika adsorpsi, arang aktif, kulit pisang, logam Pb  Abstract- Lead metal is one of environment polluter and can cause decease or health problems in sort time. The way to solve this problem is with used the carbon active from banana peel. This research is intend to find the kinetics model that appropriate in Pb adsorption process by knowing absorption of banana peel carbon active within mass variations (1; 1,5 and 2 g) and contact time (20, 40, and 60 minutes). Kinetics analysis are based from orde zero,one, and two and find the maximum capacity of adsorption from banana peel carbon active to lead metal. Equation which using at the adsorption process are Langmuir and Freundlich isotherm equations. From the analysis results, optimum time is at 60 minutes.kinetics of Pb absorption with carbon active from banana peel in mass 1 and 2 gr following kinetics model orde 2, then in mass 1,5 g following kinetics model orde 0. Langmuir equation is more appropriate in this research. Pb absorption from the banana peel that appropriate to Langmuir isotherm system is indicates adsorption was occur in one layer (monolayer). Maximum adsorption capacity is showing by the bigger value from a, that is 1,4582 in mass 1 g then interaction power of Pb with the banana peel was occur in mass 2 gr which showing with the value of kL is 0,4090.  Keywords : adsorption kinetics, carbon active, banana peel, Pb metal

scholarly journals Modified/Unmodified Nanoparticle Adsorbents of Cellulose Origin With High Adsorptive Potential for Removal of Pb(II) From Aqueous Solution

2017 ◽  
Vol 13 (27) ◽  
pp. 425
Author(s):  
Azeh Yakubu ◽  
Gabriel Ademola Olatunji ◽  
Folahan Amoo Adekola
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Adsorption Process ◽  
Correlation Coefficients ◽  
Solution Temperature ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Kinetics Of Adsorption ◽  
Kinetics Of

This investigation was conducted to evaluate the adsorption capacity of nanoparticles of cellulose origin. Nanoparticles were synthesized by acid hydrolysis of microcrystalline cellulose/cellulose acetate using 64% H3PO4 and characterized using FTIR, XRD, TGA-DTGA, BET and SEM analysis. Adsorption kinetics of Pb (II) ions in aqueous solution was investigated and the effect of initial concentration, pH, time, adsorbent dosage and solution temperature. The results showed that adsorption increased with increasing concentration with removal efficiencies of 60% and 92.99% for Azeh2 and Azeh10 respectively for initial lead concentration of 3 mg/g. The effects of contact time showed that adsorption maximum was attained within 24h of contact time. The maximum adsorption capacity and removal efficiency were achieved at pH6. Small dose of adsorbent had better performance. The kinetics of adsorption was best described by the pseudo-second-Order model while the adsorption mechanism was chemisorption and pore diffusion based on intra-particle diffusion model. The isotherm model was Freundlich. Though, all tested isotherm models relatively showed good correlation coefficients ranging from 0.969-1.000. The adsorption process was exothermic for Azeh-TDI, with a negative value of -12.812 X 103 KJ/mol. This indicates that the adsorption process for Pb by Azeh-TDI was spontaneous. Adsorption by Azeh2 was endothermic in nature.

scholarly journals Removal of lead from aqueous solutions by low cost and waste biosorbents (lemon, bean and artichoke shells)

2020 ◽  
Vol 81 (1) ◽  
pp. 159-169
Author(s):  
Feyza Ergüvenerler ◽  
Şerif Targan ◽  
Vedia Nüket Tirtom
Keyword(s):  
Contact Time ◽  
Adsorption Process ◽  
Low Cost ◽  
Standard Free Energy ◽  
Freundlich Isotherm ◽  
Standard Entropy ◽  
X Ray ◽  
Adsorption Capacities ◽  
Influence Of Ph ◽  
Scanning Electron

Abstract Simple, fast, effective, low cost and waste biosorbents, lemon, bean and artichoke shells, were used to remove lead (II) ions from aqueous solution. The influence of pH, contact time, temperature and lead (II) concentration of the removal process was investigated. The sufficient contact time was deemed 10 minutes for bean and artichoke shells and 60 minutes for lemon shells for Pb(II) ions. The thermodynamic parameters, such as standard free energy (ΔG), standard enthalpy (ΔH), and standard entropy (ΔS) of the adsorption process were calculated as −5.6786, −5.5758, −3.1488 kJmol−1 for ΔG, −7.2791, −20.285, −9.5561 kJ mol−1 for ΔH, −0.00545, −0.05017, −0.02185 kJ mol−1 K−1 for ΔS, respectively, for lemon, artichoke and bean shells. Maximum adsorption capacities of lead (II) were observed as 61.30 mg g−1, 88.5 mg g−1 and 62.81 mg g−1, respectively, for lemon, bean and artichoke shells according to the Freundlich isotherm model at 20 °C. Scanning electron microscope (SEM) and energy-dispersive X-ray detector (EDX) were used to characterize the surface morphology of the adsorbents. Consequently, Pb(II) removal using lemon, bean and artichoke shells would be an effective method for the economic treatment of wastewater.

Adsorption of Ammonium Sulfate Using Fabricated Zeolite from Waste Sludge of Water Treatment Plant

2011 ◽  
Vol 410 ◽  
pp. 220-223
Author(s):  
Kwannate Sombatsompop ◽  
Thun Jeensawak ◽  
Pongsachan Sonpai ◽  
Adithep Wangbooncong ◽  
Jeatana Wongwichien ◽  
...  
Keyword(s):  
Water Treatment ◽  
Adsorption Capacity ◽  
Ammonium Sulfate ◽  
Treatment Plant ◽  
Microscopic Analysis ◽  
Freundlich Isotherm ◽  
Water Treatment Plant ◽  
Maximum Adsorption Capacity ◽  
Electron Microscopic ◽  
Waste Sludge

This work studied an adsorption of ammonium sulfate (NH4)2SO4 from synthesized zeolite, with 3M NaOH at temperature of 90°C for 9 h, from waste sludge of water treatment plant. The scanning electron microscopic analysis revealed that the synthesized zeolite was observed to be cubic in shape. For adsorption capacity, the pH was varied at 4, 5, 6, 7 and 8, the contact times used were 0, 5, 10, 15, 30, 45 and 60 min, and the initial (NH4)2SO4 concentrations used ranged from 60-120 mg/L. The recommended pH and contact time were 8 and 15 min, respectively. Adsorption isotherm for synthesized zeolite was fitted to Langmuir model more effectively than Freundlich model. The K values for Langmuir and Freundlich isotherm was 0.061 and 1.751 L/mg with R2 values of 0.989 and 0.965, respectively. The maximum adsorption capacity was 9.597 mg/g obtained by the Langmuir isotherm. The work has concluded that the fabricated zeolite could successfully be used for adsorption of ammonium sulfate.

Extraction of Heavy Metals from Aqueous Medium by Husk Biomass: Adsorption Isotherm, Kinetic and Thermodynamic study

2019 ◽  
Vol 233 (2) ◽  
pp. 201-223 ◽  
Author(s):  
Khalida Naseem ◽  
Rahila Huma ◽  
Aiman Shahbaz ◽  
Jawaria Jamal ◽  
Muhammad Zia Ur Rehman ◽  
...  
Keyword(s):  
Metal Ions ◽  
Aqueous Medium ◽  
Contact Time ◽  
Metal Ion ◽  
Adsorption Process ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Adsorbent Dosage ◽  
Adsorption Sites ◽  
Order Kinetic Model

Abstract This study describes the adsorption of Cu (II), Co (II) and Ni (II) ions from wastewater on Vigna radiata husk biomass. The ability of adsorbent to capture the metal ions has been found to be in the order of Ni (II)>Co (II) and Cu (II) depending upon the size and nature of metal ions to be adsorbed. It has been observed that percentage removal of Cu (II), Co (II) and Ni (II) ions increases with increase of adsorbent dosage, contact time and pH of the medium but up to a certain extent. Maximum adsorption capacity (qmax) for Cu (II), Co (II) and Ni (II) ions has been found to be 11.05, 15.04 and 19.88 mg/g, respectively, under optimum conditions of adsorbent dosage, contact time and pH of the medium. Langmuir model best fits the adsorption process with R2 value approaches to unity for all metal ions as compared to other models because adsorption sites are seemed to be equivalent and only monolayer adsorption may occur as a result of binding of metal ion with a functional moiety of adsorbent. Pseudo second order kinetic model best interprets the adsorption process of Cu (II), Co (II) and Ni (II) ions. Thermodynamic parameters such as negative value of Gibbs energy (∆G°) gives information about feasibility and spontaneity of the process. Adsorption process was found to be endothermic for Cu (II) ions while exothermic for Co (II) and Ni (II) ions as signified by the value of enthalpy change (∆H°). Husk biomass was recycled three times for removal of Ni (II) from aqueous medium to investigate its recoverability and reusability. Moreover V. radiata husk biomass has a potential to extract Cu (II) and Ni (II) from electroplating wastewater to overcome the industrial waste water pollution.

Adsorption of Th(IV) on the modified multi-walled carbon nanotubes using central composite design

2019 ◽  
Vol 107 (5) ◽  
pp. 377-386 ◽  
Author(s):  
Cansu Endes Yılmaz ◽  
Mahmoud A.A. Aslani ◽  
Ceren Kütahyalı Aslani
Keyword(s):  
Carbon Nanotubes ◽  
Central Composite Design ◽  
Contact Time ◽  
Adsorption Process ◽  
Freundlich Isotherm ◽  
Thorium Concentration ◽  
Multi Walled Carbon Nanotubes ◽  
Pseudo Second Order ◽  
Walled Carbon Nanotubes ◽  
Central Composite

Abstract Adsorption of thorium onto nitric acid modified multi-walled carbon nanotubes was investigated by central composite design as a function of contact time, pH, initial thorium concentration and temperature. The results showed that optimum uptake capacity was 65.75±2.23 mg·g−1 with respect to pH=4, initial thorium concentration of 100 mg·L−1, 25 °C and 15 min contact time. Thermodynamic parameters [standard enthalpy (ΔH0), entropy (ΔS0), and free energy (ΔG0)] were calculated, and the results indicated that adsorption was endothermic. Langmuir, Freundlich and Dubinin-Radushkevich isotherms have been investigated in order to characterize the adsorption process in the range of 25–100 mg·L−1 initial thorium concentration. The Freundlich isotherm is the best suited as a model because it has the highest correlation coefficient (R2=0.9485). The pseudo-second order kinetics well defined the adsorption process.

Sign in / Sign up

Export Citation Format

Share Document