Research on Throttle Optimal Control of Flipper Jack for Hydraulic Support

2012 ◽  
Vol 503-504 ◽  
pp. 824-827
Author(s):  
Chun Qiang Jia ◽  
Wei Li ◽  
Ling Yu
Keyword(s):  
Optimal Control ◽  
Simulation Model ◽  
High Efficiency ◽  
Hydraulic Support ◽  
Simulation Results ◽  
Amesim Simulation

To solve the problem of support speed of hydraulic support flipper, the match relations between the flipper throttle control and shearer cutting coal speed are analyzed, the AMESim simulation model of the throttle optimal control for hydraulic support flipper jack is established, the simulation results show that flipper can be supported timely by speed optimal control of flipper jack which improve the reliability of the system and provide certain theory basis to meet the miner safety and high efficiency production.

Simulation Research on Hydraulic Support Column System Based on AMESim

2012 ◽  
Vol 229-231 ◽  
pp. 1684-1687
Author(s):  
Jun Zhu ◽  
Feng Yuan ◽  
Hong Xia Wu
Keyword(s):  
Simulation Model ◽  
Working Conditions ◽  
Hydraulic System ◽  
Hydraulic Support ◽  
Simulation Research ◽  
Column System ◽  
Actual Working ◽  
Working Principle ◽  
Simulation Results ◽  
Working Procedure

The working principle and process of the hydraulic support column system is introduced at first. The simulation model of the column system is established in the software of AMESim, and the parameters of the model are set according to the actual working conditions. The simulation curves of each working procedure are obtained, and the simulation results are analyzed. The conclusions will be essential references for the research on the entire support hydraulic system.

Dynamic Simulation of Air Suspension with Auxiliary Chamber

2014 ◽  
Vol 628 ◽  
pp. 195-198
Author(s):  
Ming Jun Zheng ◽  
Xiao Lei Zhang ◽  
Zhen Wang
Keyword(s):  
Simulation Model ◽  
Dynamic Characteristics ◽  
Volume Ratio ◽  
Main Chamber ◽  
Inflation Pressure ◽  
Air Spring ◽  
Air Suspension ◽  
Simulation Results ◽  
Amesim Simulation ◽  
Orifice Size

In this paper, a vehicle use air suspension with auxiliary chamber simulation model was established by the AMEsim pneumatic platform. The influences of the air spring inflation pressure, volume ratio of the main chamber and auxiliary chamber and orifice size on dynamic characteristics of the vertical air suspension were analyzed in detail. In order to verify the accuracy of the AMEsim simulation model, the AMEsim analysis results were compared with Simulink simulation results. The identical simulation results verify the reliability of AMEsim simulation. The study reveals that: the diversification of the volume ratio of the main chamber and auxiliary chamber, air spring inflation pressure and orifice size has different degrees influences on the dynamic characteristics of the air suspension with auxiliary chamber.

Tail shapes lead to different propulsive mechanisms in the body/caudal fin undulation of fish

2020 ◽  
pp. 095440622096768
Author(s):  
Jialei Song ◽  
Yong Zhong ◽  
Ruxu Du ◽  
Ling Yin ◽  
Yang Ding
Keyword(s):  
Numerical Simulation ◽  
Aspect Ratio ◽  
High Efficiency ◽  
The Body ◽  
Caudal Fin ◽  
Fish Model ◽  
Swimming Efficiency ◽  
Simulation Results ◽  
Propulsive Mechanism ◽  
High Depth

In this paper, we investigate the hydrodynamics of swimmers with three caudal fins: a round one corresponding to snakehead fish ( Channidae), an indented one corresponding to saithe ( Pollachius virens), and a lunate one corresponding to tuna ( Thunnus thynnus). A direct numerical simulation (DNS) approach with a self-propelled fish model was adopted. The simulation results show that the caudal fin transitions from a pushing/suction combined propulsive mechanism to a suction-dominated propulsive mechanism with increasing aspect ratio ( AR). Interestingly, different from a previous finding that suction-based propulsion leads to high efficiency in animal swimming, this study shows that the utilization of suction-based propulsion by a high- AR caudal fin reduces swimming efficiency. Therefore, the suction-based propulsive mechanism does not necessarily lead to high efficiency, while other factors might play a role. Further analysis shows that the large lateral momentum transferred to the flow due to the high depth of the high- AR caudal fin leads to the lowest efficiency despite the most significant suction.

Research on springback characteristic in flexible multi-points 3D stretch-bending process

2021 ◽  
pp. 095440542110284
Author(s):  
Song Gao ◽  
Tonggui He ◽  
Qihan Li ◽  
Yingli Sun ◽  
Jicai Liang
Keyword(s):  
Simulation Model ◽  
High Efficiency ◽  
Vertical Direction ◽  
Factors Affecting ◽  
Stretch Bending ◽  
Element Simulation ◽  
Bending Process ◽  
Bending Radius ◽  
Aluminum Profiles ◽  
Bending Sequence

The problem of springback is one of the most significant factors affecting the forming accuracy for aluminum 3D stretch-bending parts. In order to achieve high-efficiency and high-quality forming of such kind of structural components, the springback behaviors of the AA6082 aluminum profiles are investigated based on the flexible multi-points 3D stretch-bending process (3D FSB). Firstly, a finite element simulation model for the 3D FSB process was developed to analyze the forming procedure and the springback procedure. The forming experiments were carried out for the rectangle-section profile to verify the effectiveness of the simulation model. Secondly, the influence of tension on springback was studied, which include the pre-stretching and the post-stretching. Furthermore, the influences of the bending radius and bending sequence are revealed. The results show that: (1) The numerical model can be used to evaluate the effects of bending radius and process parameters on springback in the 3D FSB process effectively. (2) The pre-stretching has little effect on the horizontal springback reduction, but it plays a prominent role in reducing the springback in the vertical direction. (3) The increase of bending deformation in any direction will lead to an increase of springback in its direction and reduce the springback in the other direction. Besides, it reduces the relative error in both directions simultaneously. This research established a foundation to achieve the precise forming of the 3D stretch-bending parts with closed symmetrical cross-section.

scholarly journals Stability and Manoeuvrability Simulation of a Semi-Autonomous Submarine Free-Running Model SUBOFF with an Autopilot System

2021 ◽  
Vol 11 (1) ◽  
pp. 410
Author(s):  
Yu-Hsien Lin ◽  
Yu-Ting Lin ◽  
Yen-Jun Chiu
Keyword(s):  
Optimal Control ◽  
Experimental Tests ◽  
Degree Of Freedom ◽  
Line Of Sight ◽  
Pd Controller ◽  
Free Running ◽  
Simulation Results ◽  
Guidance Algorithm ◽  
Logic Operations ◽  
Six Degree Of Freedom

On the basis of a full-appendage DARPA SUBOFF model (DTRC model 5470), a scale (λ = 0.535) semi-autonomous submarine free-running model (SFRM) was designed for testing its manoeuvrability and stability in the constrained water. Prior to the experimental tests of the SFRM, a six-degree-of-freedom (6-DOF) manoeuvre model with an autopilot system was developed by using logic operations in MATLAB. The SFRM’s attitude and its trim polygon were presented by coping with the changes in mass and trimming moment. By adopting a series of manoeuvring tests in empty tanks, the performances of the SFRM were introduced in cases of three sailing speeds. In addition, the PD controller was established by considering the simulation results of these manoeuvring tests. The optimal control gains with respect to each manoeuvring test can be calculated by using the PID tuner in MATLAB. Two sets of control gains derived from the optimal characteristics parameters were compared in order to decide on the most appropriate PD controller with the line-of-sight (LOS) guidance algorithm for the SFRM in the autopilot simulation. Eventually, the simulated trajectories and course angles of the SFRM would be illustrated in the post-processor based on the Cinema 4D modelling.

scholarly journals Macro Modeling of V-Shaped Electro-Thermal MEMS Actuator with Human Error Factor

Micromachines ◽  
2021 ◽  
Vol 12 (6) ◽  
pp. 622
Author(s):  
Dongpeng Zhang ◽  
Anjiang Cai ◽  
Yulong Zhao ◽  
Tengjiang Hu
Keyword(s):  
Neural Network ◽  
Simulation Model ◽  
Bp Neural Network ◽  
Human Error ◽  
Calculation Model ◽  
Fuzzy Mathematics ◽  
Ansys Simulation ◽  
Macro Modeling ◽  
Error Factor ◽  
Simulation Results

The V-shaped electro-thermal MEMS actuator model, with the human error factor taken into account, is presented in this paper through the cascading ANSYS simulation model and the Fuzzy mathematics calculation model. The Fuzzy mathematics calculation model introduces the human error factor into the MEMS actuator model by using the BP neural network, which effectively reduces the error between ANSYS simulation results and experimental results to less than 1%. Meanwhile, the V-shaped electro-thermal MEMS actuator model, with the human error factor included, will become more accurate as the database of the V-shaped electro-thermal actuator model grows.

scholarly journals Monte Carlo Modeling and Design of Photon Energy Attenuation Layers for >10× Quantum Yield Enhancement in Si-Based Hard X-ray Detectors

Instruments ◽  
2021 ◽  
Vol 5 (2) ◽  
pp. 17
Author(s):  
Eldred Lee ◽  
Kaitlin M. Anagnost ◽  
Zhehui Wang ◽  
Michael R. James ◽  
Eric R. Fossum ◽  
...  
Keyword(s):  
Monte Carlo Simulation ◽  
Monte Carlo ◽  
Quantum Yield ◽  
Photon Energy ◽  
High Efficiency ◽  
High Energy ◽  
Yield Enhancement ◽  
X Ray ◽  
Simulation Results ◽  
Conversion Efficiencies

High-energy (>20 keV) X-ray photon detection at high quantum yield, high spatial resolution, and short response time has long been an important area of study in physics. Scintillation is a prevalent method but limited in various ways. Directly detecting high-energy X-ray photons has been a challenge to this day, mainly due to low photon-to-photoelectron conversion efficiencies. Commercially available state-of-the-art Si direct detection products such as the Si charge-coupled device (CCD) are inefficient for >10 keV photons. Here, we present Monte Carlo simulation results and analyses to introduce a highly effective yet simple high-energy X-ray detection concept with significantly enhanced photon-to-electron conversion efficiencies composed of two layers: a top high-Z photon energy attenuation layer (PAL) and a bottom Si detector. We use the principle of photon energy down conversion, where high-energy X-ray photon energies are attenuated down to ≤10 keV via inelastic scattering suitable for efficient photoelectric absorption by Si. Our Monte Carlo simulation results demonstrate that a 10–30× increase in quantum yield can be achieved using PbTe PAL on Si, potentially advancing high-resolution, high-efficiency X-ray detection using PAL-enhanced Si CMOS image sensors.

Simulation on the Regulating Characteristics of the Pulse Modulation Hydraulic Hammer

2011 ◽  
Vol 422 ◽  
pp. 176-183
Author(s):  
Gang Wang ◽  
Yu Wan Cen
Keyword(s):  
Time Delay ◽  
Simulation Model ◽  
Impact Energy ◽  
High Speed ◽  
Impact Frequency ◽  
Pulse Modulation ◽  
Motion Equations ◽  
Hydraulic Hammer ◽  
Working Frequency ◽  
Simulation Results

To improve the regulating characteristics of impact energy, simplify structure of hydraulic hammer, a new pulse modulation hydraulic hammer is presented in the paper which can help regulate its impact frequency easily. The motion equations of the hydraulic hammer are established, its simulation model is obtained and the dynamic simulation is carried out on AMESim. The dynamics of high-speed ON/OFF valve is taken into account in the simulation model. The tendency of simulation results conforms to experimental results; it shows that the pulse modulation hydraulic hammer is feasible, and the hydraulic hammer model is reasonable. The time delay in high working frequency is also analyzed.

Heating Performance Research in the Running-In Process of Wet Friction Clutch

2014 ◽  
Vol 614 ◽  
pp. 12-15
Author(s):  
Yu Fei Liu ◽  
Xiu Chao Bai ◽  
Xin Li ◽  
Yong Liang Lei
Keyword(s):  
Simulation Model ◽  
Temperature Control ◽  
Temperature Rise ◽  
Analysis Model ◽  
Heating Performance ◽  
Wet Friction ◽  
Friction Clutch ◽  
Simulation Results ◽  
Model Of Friction ◽  
Performance Research

The heating in the running-in process of wet friction clutch is the key to research in this kind of products. In this paper, based on the shifting clutch composed of metal and paper-based friction liner, using MATLAB/SIMULINK software, the simulation model of friction clutch and the analysis model of conducting heat were established. Thus, the corresponding relationships were obtained, which were the total friction power and clutch temperature variation with the time during the running-in process. According to the simulation results, the main influencing factors on temperature control of wet friction clutch were analyzed during running-in process, and the results could provide reference for reasonable temperature rise control for the clutch.

The Study of p-n and Schottky Junction for Magnetodiode

2011 ◽  
Vol 378-379 ◽  
pp. 663-667 ◽  
Author(s):  
Toempong Phetchakul ◽  
Wittaya Luanatikomkul ◽  
Chana Leepattarapongpan ◽  
E. Chaowicharat ◽  
Putapon Pengpad ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Electrical Properties ◽  
Simulation Model ◽  
Hall Effect ◽  
Schottky Junction ◽  
Field Sensitivity ◽  
Field Response ◽  
Type Semiconductor ◽  
Simulation Results ◽  
P Type

This paper presents the simulation model of Dual Magnetodiode and Dual Schottky Magnetodiode using Sentaurus TCAD to simulate the virtual structure of magneto device and apply Hall Effect to measure magnetic field response of the device. Firstly, we use the program to simulate the magnetodiode with p-type semiconductor and aluminum anode and measure electrical properties and magnetic field sensitivity. Simulation results show that sensitivity of Dual Schottky magnetodiode is higher than that of Dual magnetodiode.

Sign in / Sign up

Export Citation Format

Share Document