Effects of Aging Parameters on the Mechanical Properties in Corson Alloy System with High Contents of Ni and Si

2010 ◽  
Vol 654-656 ◽  
pp. 2568-2571 ◽  
Author(s):  
Genjiro Hagino ◽  
Hayao Eguchi ◽  
Yoshimasa Takayama ◽  
Hajime Kato
Keyword(s):  
Mechanical Properties ◽  
Electrical Conductivity ◽  
Tensile Strength ◽  
Precipitation Hardening ◽  
Solution Treatment ◽  
Alloy System ◽  
Linear Analysis ◽  
Matrix Phase ◽  
Maximum Hardness ◽  
Effects Of Aging

The influences of solution treatments, prior cold drawings and aging treatments on mechanical properties in Corson alloy with high contents more than 8.0 mass% of Ni and Si have been investigated. As a result of the optimization of conditions, the maximum hardness and tensile strength reached 306HV and 968MPa, respectively. Effects of temperatures of solution treatment and aging on the mechanical properties were analyzed based on solid solute concentrations in matrix phase, which were estimated by using the linear analysis and calculated from the electrical conductivity. The solute concentrations were also measured directly by SEM-EDS. Consequently, the precipitation hardening of the alloys was governed mainly by the solute concentrations of Ni and Si in matrix phase in solution treatment. The hardness depended on not only the solute concentrations but also the excess of Ni and Si in the alloys.

Correlation of Strength with Hardness and Electrical Conductivity for Aluminium Alloy 7010

2006 ◽  
Vol 519-521 ◽  
pp. 853-858 ◽  
Author(s):  
Manuel A. Salazar-Guapuriche ◽  
Y.Y. Zhao ◽  
Adam Pitman ◽  
Andrew Greene
Keyword(s):  
Mechanical Properties ◽  
Electrical Conductivity ◽  
Tensile Strength ◽  
Aluminium Alloy ◽  
Precipitation Hardening ◽  
Age Hardening ◽  
Al Alloy ◽  
Wide Range ◽  
Proof Strength ◽  
The Relationship

The tensile strength, proof strength, hardness and electrical conductivity of Al alloy 7010 under different temper and ageing conditions were investigated with the aim to correlate strength with hardness and electrical conductivity so that the strength of the alloy can be determined nondestructively. Following the solutionising treatment, continuous age hardening was performed on a series of test coupons, taken from a large plate, to produce a wide range of precipitation hardening conditions, which gave rise to progressive variations of strength, hardness and conductivity. The relationship between strength and hardness was found to be reasonably linear, whereas the relationship between hardness and strength with electrical conductivity was non-linear. The ageing conditions and therefore the mechanical properties of the components can be predicted more accurately by the simultaneous combination of hardness and conductivity values.

Mechanical Properties and Aging Behavior of Ultrafine Grained Al-Ag Alloy Fabricated by Accumulative Roll-Bonding

2014 ◽  
Vol 794-796 ◽  
pp. 851-856
Author(s):  
Tadashiege Nagae ◽  
Nobuhiro Tsuji ◽  
Daisuke Terada
Keyword(s):  
Mechanical Properties ◽  
Grain Refinement ◽  
Accumulative Roll Bonding ◽  
Precipitation Hardening ◽  
Tensile Elongation ◽  
Solution Treatment ◽  
High Strength ◽  
Subsequent Aging ◽  
Roll Bonding ◽  
Ultrafine Grained

Accumulative roll-bonding (ARB) process is one of the severe plastic deformation processes for fabricating ultrafine grained materials that exhibit high strength. In aluminum alloys, aging heat treatment has been an important process for hardening materials. In order to achieve good mechanical properties through the combination of grain refinement hardening and precipitation hardening, an Al-4.2wt%Ag binary alloy was used in the present study. After a solution treatment at 550°C for 1.5hr, the alloy was severely deformed by the ARB process at room temperature (RT) up to 6 cycles (equivalent strain of 4.8). The specimens ARB-processed by various cycles (various strains) were subsequently aged at 100, 150, 200, 250°C, and RT. The hardness of the solution treated (ST) specimen increased by aging. On the other hand, hardness of the ARB processed specimen decreased after aging at high temperatures such as 250°C. This was probably due to coarsening of precipitates or/and matrix grains. The specimen aged at lower temperature showed higher hardness. The maximum harnesses achieved by aging for the ST specimen, the specimens ARB processed by 2 cycles, 4 cycles and 6 cycles were 55HV, 71HV, 69HV and 65HV, respectively. By tensile tests it was shown that the strength increased by the ARB process though the elongation decreased significantly. However, it was found that the tensile elongation of the ARB processed specimens was improved by aging without sacrificing the strength. The results suggest that the Al-Ag alloy having large elongation as well as high strength can be realized by the combination of the ARB process for grain refinement and the subsequent aging for precipitation hardening.

The Investigation on Aluminium Alloys Automobile Wheel with Low-Titanium Content Produced by Electrolysis

2005 ◽  
Vol 475-479 ◽  
pp. 317-320 ◽  
Author(s):  
Jing Pei Xie ◽  
Ji Wen Li ◽  
Zhong Xia Liu ◽  
Ai Qin Wang ◽  
Yong Gang Weng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Aluminium Alloys ◽  
Solution Treatment ◽  
A356 Alloy ◽  
Aging Treatment ◽  
Titanium Content ◽  
The Matrix ◽  
Automobile Wheel

The in-situ Ti alloying of aluminium alloys was fulfilled by electrolysis, and the material was made into A356 alloy and used in automobile wheels. The results show that the grains of the A356 alloy was refined and the second dendrites arm was shortened due to the in-situ Ti alloying. Trough 3-hour solution treatment and 2-hour aging treatment for the A356 alloy, the microstructures were homogeneous, and Si particles were spheroid and distribute in the matrix fully. The outstanding mechanical properties with tensile strength (σb≥300Mpa) and elongation values (δ≥10%) have been obtained because the heat treatment was optimized. Compared with the traditional materials, tensile strength and elongation were increased by 7.6~14.1% and 7.4~44.3% respectively. The qualities of the automobile wheels were improved remarkably.

scholarly journals Formation of microstructure and properties of Cu-3Ti alloy in thermal and thermomechanical processes

2017 ◽  
Vol 62 (1) ◽  
pp. 223-230 ◽  
Author(s):  
A. Szkliniarz
Keyword(s):  
Mechanical Properties ◽  
Electrical Conductivity ◽  
Plastic Deformation ◽  
Cold Working ◽  
Cold Deformation ◽  
Solution Treatment ◽  
Cold Plastic Deformation ◽  
Working Solution ◽  
Thermomechanical Processes ◽  
Selection Of

Abstract This paper presents the possibilities of forming the microstructure as well as mechanical properties and electrical conductivity of Cu-3Ti alloy (wt.%) in thermal and thermomechanical processes that are a combination of homogenising treatment, hot and cold working, solution treatment and ageing. Phase composition of the alloy following various stages of processing it into the specified semi-finished product was being determined too. It was demonstrated that the application of cold plastic deformation between solution treatment and ageing could significantly enhance the effect of hardening of the Cu-3Ti alloy without deteriorating its electrical conductivity. It was found that for the investigated alloy the selection of appropriate conditions for homogenising treatment, hot and cold deformation as well as solution treatment and ageing enables to obtain the properties comparable to those of beryllium bronzes.

Effect of Li on Mechanical Properties and Electrical Conductivity of the Al–Zn–Cu–Mg Based Alloys

2021 ◽  
Vol 21 (9) ◽  
pp. 4897-4901
Author(s):  
Hyo-Sang Yoo ◽  
Yong-Ho Kim ◽  
Hyeon-Taek Son
Keyword(s):  
Mechanical Properties ◽  
Electrical Conductivity ◽  
Grain Size ◽  
Tensile Strength ◽  
Spherical Particles ◽  
Al Alloy ◽  
High Angle ◽  
Average Grain Size ◽  
Strength Improvement ◽  
Li Content

In this study, changes in the microstructure, mechanical properties, and electrical conductivity of cast and extruded Al–Zn–Cu–Mg based alloys with the addition of Li (0, 0.5 and 1.0 wt.%) were investigated. The Al–Zn–Cu–Mg–xLi alloys were cast and homogenized at 570 °C for 4 hours. The billets were hot extruded into rod that were 12 mm in diameter with a reduction ratio of 38:1 at 550 °C. As the amount of Li added increased from 0 to 1.0 wt.%, the average grain size of the extruded Al alloy increased from 259.2 to 383.0 µm, and the high-angle grain boundaries (HGBs) fraction decreased from 64.0 to 52.1%. As the Li content increased from 0 to 1.0 wt.%, the elongation was not significantly different from 27.8 to 27.4% and the ultimate tensile strength (UTS) was improved from 146.7 to 160.6 MPa. As Li was added, spherical particles bonded to each other, forming an irregular particles. It is thought that these irregular particles contribute to the strength improvement.

Mechanical Properties and Microstructure Evolution of Typical Over-Aging State Al-Zn-Mg-Cu Alloy during Thermal Exposure

2021 ◽  
Vol 1026 ◽  
pp. 84-92
Author(s):  
Tao Qian Cheng ◽  
Zhi Hui Li
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Mechanical Property ◽  
Electrical Conductivity ◽  
Transmission Electron Microscopy ◽  
Tensile Strength ◽  
Thermal Exposure ◽  
Cu Alloy ◽  
Transmission Electron ◽  
Thermal Stability Of

Al-Zn-Mg-Cu alloy have been widely used in aerospace industry. However, there is still a lack of research on thermal stability of Al-Zn-Mg-Cu alloy products. In the present work, an Al-Zn-Mg-Cu alloy with T79 and T74 states was placed in the corresponding environment for thermal exposure experiments. Performance was measured by tensile strength, hardness and electrical conductivity. In this paper, precipitation observation was analyzed by transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HREM). The precipitations of T79 state alloy were GPⅡ zone, η' phase and η phase while the ultimate tensile strength, hardness and electrical conductivity were 571MPa, 188.2HV and 22.2MS×m-1, respectively. The mechanical property of T79 state alloy decreased to 530MPa and 168.5HV after thermal exposure. The diameter of precipitate increased and the precipitations become η' and η phase at the same time. During the entire thermal exposure, T74 state alloy had the same mechanical property trend as T79 state alloy. The precipitate diameter also increased while the types of precipitate did not change under thermal exposure. The size of precipitates affected the choice of dislocation passing through the particles to affect the mechanical properties.

scholarly journals Effects of Gd, Y Content on the Microstructure and Mechanical Properties of Mg-Gd-Y-Nd-Zr Alloy

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 790 ◽  
Author(s):  
Changping Tang ◽  
Kai Wu ◽  
Wenhui Liu ◽  
Di Feng ◽  
Xuezhao Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Solution Treatment ◽  
Age Hardening ◽  
Uniaxial Tensile ◽  
Microstructure And Mechanical Properties ◽  
Shaped Particle ◽  
Zr Alloy ◽  
Non Equilibrium

The effects of Gd, Y content on the microstructure and mechanical properties of Mg-Gd-Y-Nd-Zr alloy were investigated using hardness measurements, X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), and uniaxial tensile testing. The results indicate that the alloys in as-cast condition mainly consist of α-Mg matrix and non-equilibrium eutectic Mg5.05RE (RE = Gd, Y, Nd). After solution treatment, the non-equilibrium eutectics dissolved into the matrix but some block shaped RE-rich particles were left at the grain boundaries and within grains. These particles are especially Y-rich and deteriorate the mechanical properties of the alloys. Both the compositions of the eutectic and the block shaped particle were independent of the total Gd, Y content of the alloys, but the number of the particles increases as the total Gd, Y content increases. The ultimate tensile strength increases as the total Gd, Y content decreases. A Mg-5.56Gd-3.38Y-1.11Nd-0.48Zr alloy with the highest ultimate tensile strength of 280 MPa and an elongation of 1.3% was fabricated. The high strength is attributed to the age hardening behavior and the decrease in block shaped particles.

Strength of Commercial Aluminum Alloys after Equal Channel Angular Pressing and Post-ECAP Processing

2006 ◽  
Vol 114 ◽  
pp. 91-96 ◽  
Author(s):  
Maxim Yu. Murashkin ◽  
M.V. Markushev ◽  
Julia Ivanisenko ◽  
Ruslan Valiev
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Aluminum Alloys ◽  
Ultimate Tensile Strength ◽  
Equal Channel Angular Pressing ◽  
Room Temperature ◽  
Solution Treatment ◽  
Ecap Processing ◽  
Angular Pressing

The effects of equal channel angular pressing (ECAP), further heat treatment and rolling on the structure and room temperature mechanical properties of the commercial aluminum alloys 6061 (Al-0.9Mg-0.7Si) and 1560 (Al-6.5Mg-0.6Mn) were investigated. It has been shown that the strength of the alloys after ECAP is higher than that achieved after conventional processing. Prior ECAP solution treatment and post-ECAP ageing can additionally increase the strength of the 6061 alloy. Under optimal ageing conditions a yield strength (YS) of 434 MPa and am ultimate tensile strength (UTS) of 470 MPa were obtained for the alloy. Additional cold rolling leads to a YS and UTS of 475 and 500 MPa with 8% elongation. It was found that the post-ECAP isothermal rolling of the 1560 alloy resulted in the formation of a nano-fibred structure and a tensile strength (YS = 540 MPa and UTS = 635 MPa) that has never previously been observed in commercial non-heat treatable alloys.

Effects of Aging on the Mechanical Properties of Pipeline Steels

2008 ◽  
Author(s):  
Martin Hukle ◽  
Brian Newbury ◽  
Dan Lillig ◽  
Jonathan Regina ◽  
Agnes Marie Horn
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Uniform Elongation ◽  
Weld Line ◽  
Base Material ◽  
Pipeline System ◽  
Line Pipe ◽  
Pipeline Steels ◽  
Reduction Of Area ◽  
Effects Of Aging

The intelligent design of a given pipeline system intended for operation beyond the elastic limit should incorporate specific features into both the base material (line pipe) and girth weld that enable the affected system to deform safely into the plastic regime within the intended strain demand limits. The current paper focuses on the mechanical properties known to influence the strain capacity of the base material (i.e., line pipe steel independent of the girth weld). Line pipe mechanical properties of interest include: longitudinal yield strength, tensile strength, yield to tensile strength ratio, reduction of area, elongation and uniform elongation. Of particular interest (in consideration of the conventional thermally applied corrosion protection coating systems to be employed), are the longitudinal mechanical properties in the “aged” condition. The present study investigates six (6) different pipeline steels encompassing grades X60 (415 MPa) to X100 (690 MPa), and includes both UOE Submerged Arc Welded - Longitudinal (SAW-L) and seamless (SMLS) forming methods.

Effect of Mg and Cu Additions on Microstructure and Mechanical Properties of Squeeze Casting Al-Si-Cu-Mg Alloy

2016 ◽  
Vol 850 ◽  
pp. 511-518 ◽  
Author(s):  
Hai Jun Liu ◽  
Lie Jun Li ◽  
Jian Wei Niu ◽  
Ji Xiang Gao ◽  
Chuan Dong Ren
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Artificial Aging ◽  
Squeeze Casting ◽  
Solution Treatment ◽  
Mg Alloys ◽  
Percentage Elongation ◽  
Microstructure And Mechanical Properties ◽  
Content Ratio ◽  
Cast Alloys

The effects of Mg and Cu additions with different contents on the mechanical properties of Al-Si alloy prepared by indirect squeeze casting have been experimentally investigated. The microstructure and mechanical properties of as-cast and T6-treated Al-Si-Cu-Mg alloys were tested by OM, SEM, DSC and tensile measurement, where the samples were produced by artificial aging at 180°C for 8 h after solution treatment at 540°C for 4 h. It has been found that for the as-cast alloys, with increasing contents of Mg and Cu the tensile strength (UTS) and yield strength (YS) increased, while the percentage elongation (El) decreased. And the optimal mechanical properties of Al-Si-Cu-Mg alloys were obtained under the content ratio of Cu/Mg within 4, where the UTS and El reached 426 MPa and 6.3% after T6 treated, respectively.

Sign in / Sign up

Export Citation Format

Share Document