scholarly journals Research into the Production of Tungsten Heavy Alloys with Specific Mechanical Properties

2019 ◽  
Vol 10 (4) ◽  
pp. 23-36
Author(s):  
Paweł SKOCZYLAS ◽  
Zbigniew GULBINOWICZ ◽  
Olgierd GOROCH ◽  
Katarzyna BARCZ ◽  
Mieczysław KACZOROWSKI
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Testing Machine ◽  
Development Project ◽  
Liquid Phase Sintering ◽  
Heavy Alloys ◽  
Heat Treated ◽  
Critical Technology ◽  
Two Stages ◽  
New Generation

The subject of the work discussed herein and carried out as a part of the Polish National Centre of Research and Development project titled ”Development and implementation of critical technology demonstrators for the new generation of 120 mm tank artillery ammunition” are the results of a research into the influence of LPS (Liquid Phase Sintering) parameters and heat treatment on the mechanical properties of W91Ni6Co3 and W91Ni6Co2.25Fe0.75 alloys, designated PR200 and PR201, respectively. The alloys, as LPS-processed and heat treated, were tested on a strength testing machine to determine their tensile strength (Rm), proof stress (Rp0.2) and elongation (A5). The analysis of the test results resulted in a proposal of manufacturing process parameters to have the alloys tested develop specified mechanical properties. It was found the ternary alloy with chemical composition W91Ni6Co3 and designated PR200 was more promising in the feasibility of producing specified mechanical properties. The alloy, once sintered and heat treated in two stages, could facilitate production of a material with a tensile strength Rm>1400 MPa, a yield strength Rp0.2 > 1350 MPa, a minimum elongation of 11%, and an impact strength > 115 J/cm2.

Effect of Heat Setting Methods on Structures and Properties of High Strength Polyvinyl Alcohol Fibre

2015 ◽  
Vol 815 ◽  
pp. 643-648
Author(s):  
Yin Zhu ◽  
Jiong Xin Zhao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Polyvinyl Alcohol ◽  
Setting Time ◽  
High Strength ◽  
Single Fibre ◽  
X Ray Diffraction ◽  
Heat Setting ◽  
Heat Treated ◽  
Setting Process

The effect of heat setting methods on the structures and mechanical properties of high strength polyvinyl alcohol (PVA) fibre is studied in this article. The microstructure and mechanical properties of heat treated PVA fibre is investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD), and single fibre electronic tensile strength tester. Results show that the heat setting method with constant tension is a good heat setting method which can largely enhance the tensile strength of PVA fibre. During the heat setting process, the mechanical properties of PVA fibre are greatly affected by the temperature, tension and setting time. When the temperature is 220°C, tension is 5cN/dtex and setting time is 90sec, the tensile strength of PVA fibre increases from 12.0cN/dtex to 16.4cN/dtex in compare with the PVA fibre without heat setting

scholarly journals Styrene–Acrylic Emulsion with “Transition Layer” for Damping Coating: Synthesis and Characterization

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1406
Author(s):  
Daoyuan Chen ◽  
Mingjin Ding ◽  
Zhixiong Huang ◽  
Yanbing Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Transition Layer ◽  
Testing Machine ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Latex Film ◽  
Seeded Emulsion Polymerization ◽  
Acrylic Emulsion ◽  
Dynamic Mechanical

In order to study the dynamic mechanical properties of styrene–acrylic latex with a core/shell structure, a variety of latexes were synthesized by semi-continuous seeded emulsion polymerization based on “particle design” with the same material. The latexes were characterized by rotary viscosimeter, dynamic light scattering (DLS), Fourier transform infrared spectroscopy (FTIR), transmission electron microscope (TEM), dynamic mechanical analysis (DMA), and universal testing machine. The effects of difference at the glass transition temperature (Tg) of core and shell and the introduction of the “transition layer” on the damping and mechanical properties of latex film were studied. The results indicate that as the Tg of core and shell gets closer, the better the compatibility of core and shell, from phase separation to phase continuity. Furthermore, the introduction of the “transition layer” can effectively improve the tensile strength and tan δ (max) of the latex film. The tensile strength and maximum loss factor (f = 1 Hz) of latex with the “transition layer” increased by 36.73% and 29.11% respectively compared with the latex without the “transition layer”. This work provides a reference for the design of emulsion for damping coating.

The effect of ageing duration on the mechanical properties of Al alloy 6061-garnet composites

2001 ◽  
Vol 215 (2) ◽  
pp. 113-119
Author(s):  
S C Sharma
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Al Alloy ◽  
Destructive Testing ◽  
Transmission Electron ◽  
Heat Treated ◽  
The Matrix ◽  
Reinforcing Particle ◽  
Alloy 6061

A well-consolidated composite of Al alloy 6061 reinforced with 4, 8 and 12 wt% garnet was prepared by a liquid metallurgy technique, the composite was heat treated for different ageing durations (T6 treatment), and its mechanical properties were determined by destructive testing. The results of the study indicated that, as the garnet particle content in the composites increased, there were marked increases in the ultimate tensile strength, compressive strength and hardness but there was a decrease in the ductility. There was an improvement in the tensile strength, compressive strength, and hardness with ageing due to precipitation. Precipitation in Al alloy 6061, with and without garnet particulate reinforcement, was studied using transmission electron microscopy. The fracture behaviour of the composites was altered significantly by the presence of garnet particles and the crack propagation through the matrix, and the reinforcing particle clusters resulted in final fracture.

scholarly journals Effects of Zr, Y on the Microstructure and Properties of As-Cast Cu-0.5Y-xZr (wt.%) Alloys

Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1084
Author(s):  
Dong Liang ◽  
Ning Wang ◽  
Yuxiang Wang ◽  
Zhenjie Liu ◽  
Ying Fu
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Tensile Strength ◽  
Copper Alloys ◽  
Testing Machine ◽  
Elongation Rate ◽  
Nominal Composition ◽  
Microstructure And Properties ◽  
Universal Material Testing Machine ◽  
Material Testing Machine

In this paper, the microstructure and properties of as-cast Cu-Y-Zr alloys with different Zr content were studied in order to investigate whether the precipitates in copper alloys would interact with each other by adding Y and Zr simultaneously. As-cast Cu-0.5Y-xZr (wt.%, x = 0.05 and 0.1, nominal composition) alloys were prepared by vacuum melting in this study. Scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), and transmission electron microscopy (TEM) were used to observe the microstructure of the alloys. The mechanical properties of the alloys were tested by universal material testing machine at room temperature. The effects of Zr content on the microstructure and mechanical properties of the alloys were explored. As shown by the research results, in the as-cast Cu-0.5Y-xZr (wt.%) alloys, the precipitated phase was the Cu5Y/Cu5Zr phase and ranged from 10 nm to 70 nm in size; when the Zr content increased from 0.05 wt.% to 0.1 wt.%, both the tensile strength and elongation rate of the alloys increased; when the Zr content was 0.1 wt.%, the tensile strength was 225 MPa and the elongation rate was 22.5%.

Influence of Al-10RE Modification on Microstructure and Mechanical Properties of ZL203 Aluminum Alloy

2011 ◽  
Vol 365 ◽  
pp. 98-103
Author(s):  
De Quan Shi ◽  
Gui Li Gao ◽  
Zhi Wei Gao ◽  
Yan Liu Wang ◽  
Xu Dong Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Aluminum Alloy ◽  
Mechanical Testing ◽  
Testing Machine ◽  
Optical Microscope ◽  
Elongation Rate ◽  
Holding Time ◽  
Holding Temperature ◽  
Universal Mechanical Testing Machine

The influence of Al-10RE addition, holding time and holding temperature on the microstructures and mechanical properties of ZL203 aluminum alloy has been studied respectively through using the optical microscope and the universal mechanical testing machine. The experimental results lead to the following conclusions. When Al-10RE addition is 1.0%-1.5%, the holding time is 15 minutes and the holding temperature is 730°C-750°C, the microstructure of Zl203 is perfect. With the increase of Al-10RE addition, the mechanical properties including tensile strength, elongation rate and hardness gradually increase. When the Al-10RE addition is 1.0%-1.5%, the mechanical properties reaches maximum. When the Al-10RE addition is above 1.5%, the mechanical properties decrease with the increase of Al-10RE addition.

Effect of Heat Treatment on Tensile Strength and Microstructure of AZ61A Magnesium Alloy

2014 ◽  
Vol 606 ◽  
pp. 55-59 ◽  
Author(s):  
R. Senthil ◽  
A. Gnanavelbabu
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Magnesium Alloys ◽  
Mg Alloys ◽  
Forming Process ◽  
Microstructural Parameters ◽  
Heat Treated ◽  
Mutual Relations

Magnesium alloys are the very progressive materials whereon is due to improve their end-use properties. Especially, wrought Mg alloys attract attention since they have more advantageous mechanical properties than cast Mg alloys. Investigations were carried out the effects of heat treatment on tensile strength and microstructure of AZ61A magnesium alloy. The AZ61A Mg alloy is solution heat treated at the temperature of 6500F (343°C) for various soaking timing such as 120 min, 240 min and 360 minutes and allowed it cool slowly in the furnace itself. Magnesium alloys usually are heat treated either to improve mechanical properties or as means of conditioning for specific fabrication operations. Special attention had been focused on the analysis of mutual relations existing between the deformation conditions, microstructural parameters, grain size and the achieved mechanical properties. The result after the solution heat treatment, showed remarkably improved hardness, tensile strength and yield strength. It would be appropriate for a forming process namely isostatic forming process.

scholarly journals Comparison of mechanical and wearing properties between LM13 matrix and Stir cast LM13/B4C/Gr hybrid composites of various composition

2017 ◽  
Vol 7 (1.1) ◽  
pp. 193
Author(s):  
M.H. Faisal ◽  
S. Prabagaran ◽  
T.S. Vishnu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Boron Carbide ◽  
Hybrid Composites ◽  
Wear Behavior ◽  
Testing Machine ◽  
Matrix Composites ◽  
Hardness Tester ◽  
Negative Effect ◽  
Carbide Particles

Aluminium/graphite composites are the need of modern times for addressing the fuel saving issues. The graphite in such composites act as solid lubricant and it reduce external fuel requirements. But such composites are having degraded mechanical properties due to the graphite content in composite. In order to solve the negative effect of graphite on mechanical properties of LM13/Gr self-lubricating composite this study was conducted to find out the mechanical properties of LM13/B4C/Gr Metal Matrix Composites. Boron carbide was selected as reinforcement because of its better reinforcement properties compared to alumina and silicon carbide. The properties of the hybrid composites were compared with the LM13/Gr self-lubricating composite to study the enhancement in mechanical properties that has been caused by the boron carbide particles. Using computerized universal testing machine and rock-well hardness tester mechanical properties such as hardness and tensile strength were tested. Pin on disk testing machine was used to analyse the wear behavior. The test results indicates that by raising weight % of boron carbide particles in the LM13, tensile strength and hardness of the hybrid composites was increased compared to self-lubricating composite accompanied by better tribological properties.

scholarly journals Effect of fibre type and content on performance of bio-based concrete containing heat-treated apricot shell

2020 ◽  
Vol 53 (6) ◽  
Author(s):  
Fan Wu ◽  
Qingliang Yu ◽  
Changwu Liu ◽  
H. J. H. Brouwers ◽  
Linfeng Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Magnesium Sulfate ◽  
Fibre Type ◽  
Lightweight Concrete ◽  
Sulfate Attack ◽  
Fibre Glass ◽  
Heat Treated ◽  
Apricot Shell

AbstractThe heat-treated apricot shell can be utilized as coarse aggregates for producing sustainable bio-based lightweight concrete with good compressive strength but poor tensile strength. In order to improve the tensile properties of apricot shell concrete (ASC), the effects of polypropylene (PP) fibre, glass (G) fibre and basalt (B) fibre at various volume fractions (Vf) (0.25%, 0.5% and 0.75%) on the performance of ASC were investigated. The results indicated that the fibre type had no significant effect on the physical properties of ASC such as slump, density, water absorption and permeable porosity. However, the slump of ASC decreases with an increase in fibre content. The B fibre has a better improvement in mechanical properties than the PP fibre and G fibre thanks to the better elastic modulus and tensile strength. When the Vf was 0.5%, the compressive strength, splitting tensile strength, flexural strength and modulus of elasticity of ASC reinforced with B fibre were increased by 16.7%, 29.1%, 29.2%, and 18.1%, respectively, compared to ASC without any fibres. The magnesium sulfate attack results showed that the incorporation of the B fibre decreased the mass loss and compressive strength of ASC exposed to a MgSO4 solution for 6 months because the fibre arrested the microcracks caused by the expansive stress. It is concluded that the mechanical properties of bio-based ASC and its resistance to magnesium sulfate attack can be significantly improved by incorporating 0.5% B fibre.

Mechanical properties of heat-treated cellulose nanofiber-reinforced polyvinyl alcohol nanocomposite

2016 ◽  
Vol 51 (14) ◽  
pp. 1971-1977 ◽  
Author(s):  
NH Noor Mohamed ◽  
Hitoshi Takagi ◽  
Antonio N Nakagaito
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Polyvinyl Alcohol ◽  
Tensile Tests ◽  
Cellulose Nanofiber ◽  
Heat Treated ◽  
Scanning Electron ◽  
Polyvinyl Alcohol Films

The mechanical properties of cellulose nanofiber-reinforced polyvinyl alcohol composite were studied. Neat polyvinyl alcohol films, cellulose nanofiber sheets, and their nanocomposites containing cellulose nanofiber weight ratios of 5, 15, 30, 40, 45, 50 and 80 wt% were fabricated. Heat treatment by hot pressing at 180℃ was conducted on the specimens to study its effect to the mechanical properties and the results were compared with the non heat-treated specimens. Morphology of the composites was studied by scanning electron microscopy and the mechanical properties were evaluated by means of tensile tests. The results showed that increase of cellulose nanofiber content from 5 wt% to 80 wt% has increased the tensile strength of the composites up to 180 MPa, with cellulose nanofiber content higher than 40 wt% yielding higher tensile strength. The heat-treated specimens exhibited higher tensile strength compared to those of untreated specimens.

Effect of Sc on As-Cast Microstructures and Mechanical Properties of Al-Si-Mg-Cu-Ti Alloys

2017 ◽  
Vol 732 ◽  
pp. 32-37 ◽  
Author(s):  
Ming He Wang ◽  
Xiao Dong Du ◽  
Yu Kun Li ◽  
Zhen Zhang ◽  
Hai Lin Su ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Electron Microscope ◽  
Testing Machine ◽  
Ti Alloys ◽  
Universal Testing ◽  
Transmission Electron ◽  
Heat Treated ◽  
Eutectic Si ◽  
Microstructures And Mechanical Properties ◽  
Equiaxed Grain

The as-cast microstructures and mechanical properties of Al-Si-Mg-Cu-Ti alloys with and without Sc were investigated by metallographic microscope, field emission scanning electron microscope, energy spectrum analysis, transmission electron microscope and universal testing machine. The result shows that adding 0.20wt.% Sc into the casting alloy can refine the grain, change the growth morphology from dendrite to fine equiaxed grain, and the morphology of eutectic Si by rough laminar structure into fine fibrous. The tensile strength of alloy with 0.20wt.% Sc is up to 304.4 MPa after T6 heat treated, which is close to that of 6061 forging aluminum alloy.

Sign in / Sign up

Export Citation Format

Share Document