scholarly journals A novel approach of the grain structure modelling in the framework of polycrystalline specimen and EBSD experiment simulation

2019 ◽  
Vol 1205 ◽  
pp. 012043
Author(s):  
A O Ovchinnikova ◽  
T I Savyolova
Keyword(s):  
Grain Structure ◽  
Polycrystalline Specimen ◽  
Novel Approach

THE FORMATION OF ULTRAFINE FERRITE THROUGH STATIC TRANSFORMATION IN LOW CARBON STEELS

2008 ◽  
Vol 22 (18n19) ◽  
pp. 2804-2813
Author(s):  
Y. ADACHI ◽  
M. WAKITA ◽  
H. BELADI ◽  
P. D. HODGSON
Keyword(s):  
Deformation Temperature ◽  
Carbon Steels ◽  
Grain Structure ◽  
Dynamic Strain ◽  
Ultrafine Grain ◽  
Low Carbon ◽  
Low Carbon Steels ◽  
Novel Approach ◽  
Wide Range ◽  
Ultrafine Grain Structure

A novel approach was used to produce an ultrafine grain structure in low carbon steels with a wide range of hardenability. This included warm deformation of supercooled austenite followed by reheating in the austenite region and cooling (RHA). The ultrafine ferrite structure was independent of steel composition. However, the mechanism of ferrite refinement changed with the steel quench hardenability. In a relatively low hardenable steel, the ultrafine structure was produced through dynamic strain induced transformation, whereas the ferrite refinement was formed by static transformation in steels with high quench hardenability. The use of a model Ni -30 Fe austenitic alloy revealed that the deformation temperature has a strong effect on the nature of the intragranular defects. There was a transition temperature below which the cell dislocation structure changed to laminar microbands. It appears that the extreme refinement of ferrite is due to the formation of extensive high angle intragranular defects at these low deformation temperature that then act as sites for static transformation.

scholarly journals A Novel Approach to Predict the Process-Induced Mechanical Behavior of Additively Manufactured Materials

2021 ◽  
Author(s):  
Andreas Kergaßner ◽  
Johannes A. Koepf ◽  
Matthias Markl ◽  
Carolin Körner ◽  
Julia Mergheim ◽  
...  
Keyword(s):  
Mechanical Behavior ◽  
Yield Criterion ◽  
Grain Structure ◽  
The Finite Element Method ◽  
Present Contribution ◽  
Plastic Properties ◽  
Novel Approach ◽  
Grain Structures ◽  
Selective Electron Beam Melting ◽  
Yield Loci

AbstractThe grain structure and texture of additively manufactured materials depend strongly on the local temperature gradients during the solidification of the material. These grain structures and textures influence the mechanical behavior, ranging from isotropy to transversal and orthotropic symmetry. In the present contribution, a cellular automaton is used to model the grain growth during selective electron beam melting. The resulting grain structures and textures serve as input for a mesoscopic mechanical model. The mechanical behavior on the mesoscale is modeled by means of gradient-enhanced crystal plasticity, applying the finite element method. Computational homogenization is applied to determine the resulting macroscopic elastic and plastic properties of the additively manufactured metals. A general orthotropic yield criterion is identified by means of the initial yield loci computed with mesoscopic simulations of representative volume elements. The numerical results are partly validated with experimental data.

SEM analysis of DC magnetron sputtered beryllium films

1988 ◽  
Vol 46 ◽  
pp. 960-961
Author(s):  
E. F. Lindsey ◽  
C. W. Price ◽  
E. L. Pierce ◽  
E. J. Hsieh
Keyword(s):  
Fine Structure ◽  
Electron Emission ◽  
Secondary Electron ◽  
Low Voltage ◽  
Ion Beam ◽  
Secondary Electron Emission ◽  
Sem Analysis ◽  
Fused Silica ◽  
Grain Structure ◽  
Silica Substrate

Columnar structures produced by DC magnetron sputtering can be altered by using RF biased sputtering or by exposing the film to nitrogen pulses during sputtering, and these techniques are being evaluated to refine the grain structure in sputtered beryllium films deposited on fused silica substrates. Beryllium is brittle, and fractures in sputtered beryllium films tend to be intergranular; therefore, a convenient technique to analyze grain structure in these films is to fracture the coated specimens and examine them in an SEM. However, fine structure in sputtered deposits is difficult to image in an SEM, and both the low density and the low secondary electron emission coefficient of beryllium seriously compound this problem. Secondary electron emission can be improved by coating beryllium with Au or Au-Pd, and coating also was required to overcome severe charging of the fused silica substrate even at low voltage. The coating structure can obliterate much of the fine structure in beryllium films, but reasonable results were obtained by using the high-resolution capability of an Hitachi S-800 SEM and either ion-beam coating with Au-Pd or carbon coating by thermal evaporation.

Crystallographic Characterization of Dislocation Loops in Irradiated Tungsten

1968 ◽  
Vol 26 ◽  
pp. 290-291
Author(s):  
Robert C. Rau
Keyword(s):  
Electron Microscope ◽  
Ambient Temperature ◽  
Dislocation Loops ◽  
Polycrystalline Specimen ◽  
Post Irradiation ◽  
Neutron Fluences

Previous work has shown that post-irradiation annealing, at temperatures near 1100°C, produces resolvable dislocation loops in tungsten irradiated to fast (E > 1 MeV) neutron fluences of about 4 x 1019 n/cm2 or greater. To crystallographically characterize these loops, tilting experiments were carried out in the electron microscope on a polycrystalline specimen which had been irradiated to 1.5 × 1021 n/cm2 at reactor ambient temperature (∼ 70°C), and subseouently annealed for 315 hours at 1100°C. This treatment produced large loops averaging 1000 Å in diameter, as shown in the micrographs of Fig. 1. The orientation of this grain was near (001), and tilting was carried out about axes near [100], [10] and [110].

High-resolution EM study of submicrometer-grained Al-Mg solid solution alloys

1995 ◽  
Vol 53 ◽  
pp. 524-525
Author(s):  
Z. Horita ◽  
D. J. Smith ◽  
M. Furukawa ◽  
M. Nemoto ◽  
R. Z. Valiev ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Solid Solution ◽  
High Resolution ◽  
Grain Boundaries ◽  
Energy State ◽  
High Energy ◽  
Grain Structure ◽  
Boundary Structure ◽  
Solid Solution Alloy ◽  
Average Grain Size

It is possible to produce metallic materials with submicrometer-grained (SMG) structures by imposing an intense plastic strain under quasi-hydrostatic pressure. Studies using conventional transmission electron microscopy (CTEM) showed that many grain boundaries in the SMG structures appeared diffuse in nature with poorly defined transition zones between individual grains. The implication of the CTEM observations is that the grain boundaries of the SMG structures are in a high energy state, having non-equilibrium character. It is anticipated that high-resolution electron microscopy (HREM) will serve to reveal a precise nature of the grain boundary structure in SMG materials. A recent study on nanocrystalline Ni and Ni3Al showed lattice distortion and dilatations in the vicinity of the grain boundaries. In this study, HREM observations are undertaken to examine the atomic structure of grain boundaries in an SMG Al-based Al-Mg alloy.An Al-3%Mg solid solution alloy was subjected to torsion straining to produce an equiaxed grain structure with an average grain size of ~0.09 μm.

High-resolution scanning electron microscopy of thin-film magnetic media of magnetic recording disk

1992 ◽  
Vol 50 (2) ◽  
pp. 1334-1335
Author(s):  
K. Ogura ◽  
H. Nishioka ◽  
N. Ikeo ◽  
T. Kanazawa ◽  
J. Teshima
Keyword(s):  
Thin Film ◽  
Fine Structure ◽  
High Resolution ◽  
Magnetic Recording ◽  
High Performance ◽  
Magnetic Hysteresis ◽  
Grain Structure ◽  
Magnetic Media ◽  
Cross Sectional ◽  
Resolution Observation

Structural appraisal of thin film magnetic media is very important because their magnetic characters such as magnetic hysteresis and recording behaviors are drastically altered by the grain structure of the film. However, in general, the surface of thin film magnetic media of magnetic recording disk which is process completed is protected by several-nm thick sputtered carbon. Therefore, high-resolution observation of a cross-sectional plane of a disk is strongly required to see the fine structure of the thin film magnetic media. Additionally, observation of the top protection film is also very important in this field.Recently, several different process-completed magnetic disks were examined with a UHR-SEM, the JEOL JSM 890, which consisted of a field emission gun and a high-performance immerse lens. The disks were cut into approximately 10-mm squares, the bottom of these pieces were carved into more than half of the total thickness of the disks, and they were bent. There were many cracks on the bent disks. When these disks were observed with the UHR-SEM, it was very difficult to observe the fine structure of thin film magnetic media which appeared on the cracks, because of a very heavy contamination on the observing area.

The crystal structure of eugaAl

1992 ◽  
Vol 50 (2) ◽  
pp. 1452-1453
Author(s):  
H. Brigitte Krause ◽  
Yonglin Qian
Keyword(s):  
Crystal Structure ◽  
Electron Microscope ◽  
Zone Axis ◽  
Unit Cell ◽  
Polycrystalline Specimen ◽  
Lattice Constants

A polycrystalline specimen of nominal formula EuGaAl with unknown crystal structure was investigated by various electron microscope techniques; EDS-, SED-, and CBED data were taken on a Philips 400 electron microscope operated at 100kV, HREM data on a Hitachi 9000 microscope operated at 300kV. The EDS data confirmed the composition for the bulk of the material but, in addition, revealed particles with other fractions of the elements. Only the EuGaAl particles were further investigated. The unit cell was determined to be orthorhombic with a ratio: a/b=0.969(2) , a/c=0.234(2) and b/c=0.234(2). The lattice constants are a=4.54(5)Ȧ, b=4.68Ȧ and c=19.97(20)Ȧ. Based on systematic extinctions for hkl reflections with h+l=2n+l, the unit cell was found to be b-centered. CBED patterns of the [001], [100], and [010] zone axes are shown in Fig. 1. The zone axis patterns are in agreement with the above stated data except for diffused (2m+l,2n+l,0)- reflections, not compatible with the above stated systematic absences. But these occurred only occasionally in conjunction with a complicated noncommensurate superlattice pattern.

Microstructure Development in a High Current Density NbTi Superconducting Composite

1985 ◽  
Vol 43 ◽  
pp. 186-189
Author(s):  
P. J. Lee ◽  
D. C. Larbalestier
Keyword(s):  
Current Density ◽  
High Current Density ◽  
Cold Drawing ◽  
Heat Treatments ◽  
Grain Structure ◽  
Fine Grain ◽  
Boundary Film ◽  
Quantitative Basis ◽  
Cold Worked ◽  
Very High

Several features of the metallurgy of superconducting composites of Nb-Ti in a Cu matrix are of interest. The cold drawing strains are generally of order 8-10, producing a very fine grain structure of diameter 30-50 nm. Heat treatments of as little as 3 hours at 300 C (∼ 0.27 TM) produce a thin (1-3 nm) Ti-rich grain boundary film, the precipitate later growing out at triple points to 50-100 nm dia. Further plastic deformation of these larger a-Ti precipitates by strains of 3-4 produces an elongated ribbon morphology (of order 3 x 50 nm in transverse section) and it is the thickness and separation of these precipitates which are believed to control the superconducting properties. The present paper describes initial attempts to put our understanding of the metallurgy of these heavily cold-worked composites on a quantitative basis. The composite studied was fabricated in our own laboratory, using six intermediate heat treatments. This process enabled very high critical current density (Jc) values to be obtained. Samples were cut from the composite at many processing stages and a report of the structure of a number of these samples is made here.

TEM studies of solid-state reactions in sputter-deposited Nb/Al multilayer thin films

1996 ◽  
Vol 54 ◽  
pp. 1020-1021
Author(s):  
F. Ma ◽  
S. Vivekanand ◽  
K. Barmak ◽  
C. Michaelsen
Keyword(s):  
Thin Films ◽  
Solid State ◽  
Stoichiometric Composition ◽  
Analytical Electron Microscopy ◽  
Grain Structure ◽  
Solid State Reactions ◽  
Multilayer Thin Films ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sputter Deposited

Solid state reactions in sputter-deposited Nb/Al multilayer thin films have been studied by transmission and analytical electron microscopy (TEM/AEM), differential scanning calorimetry (DSC) and X-ray diffraction (XRD). The Nb/Al multilayer thin films for TEM studies were sputter-deposited on (1102)sapphire substrates. The periodicity of the films is in the range 10-500 nm. The overall composition of the films are 1/3, 2/1, and 3/1 Nb/Al, corresponding to the stoichiometric composition of the three intermetallic phases in this system.Figure 1 is a TEM micrograph of an as-deposited film with periodicity A = dA1 + dNb = 72 nm, where d's are layer thicknesses. The polycrystalline nature of the Al and Nb layers with their columnar grain structure is evident in the figure. Both Nb and Al layers exhibit crystallographic texture, with the electron diffraction pattern for this film showing stronger diffraction spots in the direction normal to the multilayer. The X-ray diffraction patterns of all films are dominated by the Al(l 11) and Nb(l 10) peaks and show a merging of these two peaks with decreasing periodicity.

Relationships Between Grain Boundary Structure and Material Properties

1980 ◽  
Vol 38 ◽  
pp. 366-369
Author(s):  
Brian Ralph ◽  
Barlow Claire ◽  
Nicola Ecob
Keyword(s):  
Grain Boundary ◽  
Material Properties ◽  
Main Property ◽  
Grain Structure ◽  
Boundary Structure ◽  
Grain Boundary Structure ◽  
Property Changes

This brief review seeks to summarize some of the main property changes which may be induced by altering the grain structure of materials. Where appropriate an interpretation is given of these changes in terms of current theories of grain boundary structure, and some examples from current studies are presented at the end of this paper.

Sign in / Sign up

Export Citation Format

Share Document