Texture and Mechanical Behavior of Magnesium During Free-End Torsion

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
Benoît Beausir ◽  
László S. Tóth ◽  
Fathallah Qods ◽  
Kenneth W. Neale
Keyword(s):  
Room Temperature ◽  
Texture Evolution ◽  
Twist Angle ◽  
Rolled Plate ◽  
Electron Backscattering Diffraction ◽  
Consistent Model ◽  
End Conditions ◽  
Different Temperatures ◽  
Initial Texture ◽  
Hexagonal Crystals

Torsion experiments were carried out on pure magnesium (99.9%) and the magnesium alloy AZ71 under free-end conditions of testing. The alloy had an axisymmetric initial texture, while the pure Mg samples were prepared from a rolled plate with a nonaxisymmetric initial texture. The torque as a function of the twist angle was measured at different temperatures (room temperature, 150°C, and 250°C). During twisting, systematic shortening of the samples was observed (Swift effect). The evolution of the crystallographic texture was analyzed by electron backscattering diffraction measurements. The occurrence of dynamic recrystallization (DRX) was detected in pure Mg at 250°C. The Swift effect in the axisymmetric samples was simulated with the “equilibrium equation” approach using polycrystal modeling. In the nonaxisymmetric samples, the texture was simulated at different angular positions with the help of the viscoplastic self-consistent model. The changes in the textures due to DRX were explained in terms of the Taylor factor. Finally, the texture evolution was interpreted with the help of the behavior of ideal orientations and persistence characteristics of hexagonal crystals in simple shear.

Influence of Temperature upon the Texture Evolution and Mechanical Behaviour of Zircaloy-4

2011 ◽  
Vol 702-703 ◽  
pp. 834-837
Author(s):  
Peter Honniball ◽  
Michael Preuss ◽  
Joao Quinta da Fonseca
Keyword(s):  
Mechanical Behaviour ◽  
Room Temperature ◽  
Electron Backscatter Diffraction ◽  
Texture Evolution ◽  
Crystal Plasticity Finite Element ◽  
Ebsd Data ◽  
Electron Backscatter ◽  
Different Temperatures ◽  
Increasing Temperature ◽  
Backscatter Diffraction

The mechanical behaviour and texture evolution during uniaxial compression of Zircaloy-4 at different temperatures (25, 300, 500 C) has been studied. At room temperature and 300 C the texture evolution and strain-hardening behaviour observed are attributed to the activation of {10-12} tensile twinning, which can be identified in optical micrographs and electron backscatter diffraction (EBSD) data. The influence of twinning upon the texture evolution and hardening rate becomes less apparent with increasing temperature. Nevertheless twinning is still active at 500 C. Simulation of the texture evolution at 500 C using crystal plasticity finite element modelling (CPFEM) indicates that slip alone cannot explain the experimentally observed textures at this temperature.

Comparative Labelling and Biokinetic Studies of 99mTc-EDTA(Sn) and 99mTc-DTPA(Sn)

1977 ◽  
Vol 16 (01) ◽  
pp. 30-35 ◽  
Author(s):  
N. Agha ◽  
R. B. R. Persson
Keyword(s):  
Complex Formation ◽  
Significant Influence ◽  
Room Temperature ◽  
Ph Value ◽  
Maximum Activity ◽  
Reduction Step ◽  
Labelling Yield ◽  
Different Temperatures ◽  
Kinetics Of

SummaryGelchromatography column scanning has been used to study the fractions of 99mTc-pertechnetate, 99mTcchelate and reduced hydrolyzed 99mTc in preparations of 99mTc-EDTA(Sn) and 99mTc-DTPA(Sn). The labelling yield of 99mTc-EDTA(Sn) chelate was as high as 90—95% when 100 μmol EDTA · H4 and 0.5 (Amol SnCl2 was incubated with 10 ml 99mTceluate for 30—60 min at room temperature. The study of the influence of the pH-value on the fraction of 99mTc-EDTA shows that pH 2.8—2.9 gave the best labelling yield. In a comparative study of the labelling kinetics of 99mTc-EDTA(Sn) and 99mTc- DTPA(Sn) at different temperatures (7, 22 and 37°C), no significant influence on the reduction step was found. The rate constant for complex formation, however, increased more rapidly with increased temperature for 99mTc-DTPA(Sn). At room temperature only a few minutes was required to achieve a high labelling yield with 99mTc-DTPA(Sn) whereas about 60 min was required for 99mTc-EDTA(Sn). Comparative biokinetic studies in rabbits showed that the maximum activity in kidneys is achieved after 12 min with 99mTc-EDTA(Sn) but already after 6 min with 99mTc-DTPA(Sn). The long-term disappearance of 99mTc-DTPA(Sn) from the kidneys is about five times faster than that for 99mTc-EDTA(Sn).

scholarly journals Temperature-Dependent Stimulated Emission Cross-Section in Nd3+:YLF Crystal

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 431
Author(s):  
Giorgio Turri ◽  
Scott Webster ◽  
Michael Bass ◽  
Alessandra Toncelli
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Room Temperature ◽  
Radiative Decay ◽  
Emission Cross Section ◽  
Spectroscopic Properties ◽  
Stimulated Emission ◽  
Different Temperatures ◽  
Stimulated Emission Cross Section ◽  
Semi Empirical

Spectroscopic properties of neodymium-doped yttrium lithium fluoride were measured at different temperatures from 35 K to 350 K in specimens with 1 at% Nd3+ concentration. The absorption spectrum was measured at room temperature from 400 to 900 nm. The decay dynamics of the 4F3/2 multiplet was investigated by measuring the fluorescence lifetime as a function of the sample temperature, and the radiative decay time was derived by extrapolation to 0 K. The stimulated-emission cross-sections of the transitions from the 4F3/2 to the 4I9/2, 4I11/2, and 4I13/2 levels were obtained from the fluorescence spectrum measured at different temperatures, using the Aull–Jenssen technique. The results show consistency with most results previously published at room temperature, extending them over a broader range of temperatures. A semi-empirical formula for the magnitude of the stimulated-emission cross-section as a function of temperature in the 250 K to 350 K temperature range, is presented for the most intense transitions to the 4I11/2 and 4I13/2 levels.

Proteinase and phospholipase activities and development at different temperatures of yeasts isolated from bovine milk

2011 ◽  
Vol 78 (4) ◽  
pp. 385-390 ◽  
Author(s):  
Priscilla A Melville ◽  
Nilson R Benites ◽  
Monica Ruz-Peres ◽  
Eugenio Yokoya
Keyword(s):  
Dairy Products ◽  
Room Temperature ◽  
Bovine Milk ◽  
Raw Milk ◽  
Pathogenic Potential ◽  
Proteinase Production ◽  
Different Temperatures ◽  
Quality Of Milk ◽  
Means Of Transmission

The presence of yeasts in milk may cause physical and chemical changes limiting the durability and compromising the quality of the product. Moreover, milk and dairy products contaminated by yeasts may be a potential means of transmission of these microorganisms to man and animals causing several kinds of infections. This study aimed to determine whether different species of yeasts isolated from bovine raw milk had the ability to develop at 37°C and/or under refrigeration temperature. Proteinase and phospholipase activities resulting from these yeasts were also monitored at different temperatures. Five genera of yeasts (Aureobasidium sp., Candida spp., Geotrichum spp., Trichosporon spp. and Rhodotorula spp.) isolated from bovine raw milk samples were evaluated. All strains showed one or a combination of characteristics: growth at 37°C (99·09% of the strains), psychrotrophic behaviour (50·9%), proteinase production (16·81% of the strains at 37°C and 4·09% under refrigeration) and phospholipase production (36·36% of the isolates at 37°C and 10·9% under refrigeration), and all these factors may compromise the quality of the product. Proteinase production was similar for strains incubated at 37°C (16·81% of the isolates) and room temperature (17·27%) but there was less amount of phospholipase-producing strains at room temperature (15·45% of the isolates were positive) when compared with incubation at 37°C (36·36%). Enzymes production at 37°C by yeasts isolated from milk confirmed their pathogenic potential. The refrigeration temperature was found to be most efficient to inhibit enzymes production and consequently ensure better quality of milk. The viability of yeasts and the activity of their enzymes at different temperatures are worrying because this can compromise the quality of dairy products at all stages of production and/or storage, and represent a risk to the consumer.

scholarly journals E/D-Mode GaN Inverter on a 150-mm Si Wafer Based on p-GaN Gate E-Mode HEMT Technology

Micromachines ◽  
2021 ◽  
Vol 12 (6) ◽  
pp. 617
Author(s):  
Li-Fang Jia ◽  
Lian Zhang ◽  
Jin-Ping Xiao ◽  
Zhe Cheng ◽  
De-Feng Lin ◽  
...  
Keyword(s):  
Integrated Circuit ◽  
Room Temperature ◽  
Supply Voltage ◽  
High Input ◽  
Smart Power ◽  
Input Noise ◽  
Power Integrated Circuit ◽  
Different Temperatures ◽  
Device Technology ◽  
Si Wafer

AlGaN/GaN E/D-mode GaN inverters are successfully fabricated on a 150-mm Si wafer. P-GaN gate technology is applied to be compatible with the commercial E-mode GaN power device technology platform and a systematic study of E/D-mode GaN inverters has been conducted with detail. The key electrical characters have been analyzed from room temperature (RT) to 200 °C. Small variations of the inverters are observed at different temperatures. The logic swing voltage of 2.91 V and 2.89 V are observed at RT and 200 °C at a supply voltage of 3 V. Correspondingly, low/high input noise margins of 0.78 V/1.67 V and 0.68 V/1.72 V are observed at RT and 200 °C. The inverters also demonstrate small rising edge time of the output signal. The results show great potential for GaN smart power integrated circuit (IC) application.

Effect on Vulcanized Rubber Compounds of Immersion in Boiling Water

1931 ◽  
Vol 4 (3) ◽  
pp. 426-436
Author(s):  
K. J. Soule
Keyword(s):  
Water Absorption ◽  
Room Temperature ◽  
Anomalous Behavior ◽  
Boiling Water ◽  
Vulcanized Rubber ◽  
Rubber Compounds ◽  
Different Temperatures ◽  
Actual Change

Abstract Further work is very desirable on the effect of different accelerators, antioxidants, and fluxes. It is possible that their study will throw more light on the mechanism of the swelling phenomena, and also help to explain the anomalous behavior of some of the fillers tested. It would also seem to be worth while to study the action of a few selected stocks in water, at several temperatures between room temperature and 100° C., to determine if the water absorption and swelling merely increase with rising temperatures, or whether there might be an actual change in behavior at different temperatures.

scholarly journals Investigation of Fatigue Behavior of ABS and PC-ABS Polymers at Different Temperatures

Materials ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 1818
Author(s):  
Andrea Mura ◽  
Alessando Ricci ◽  
Giancarlo Canavese
Keyword(s):  
High Temperature ◽  
Room Temperature ◽  
Working Condition ◽  
Fatigue Behavior ◽  
Polymeric Materials ◽  
Cyclic Loads ◽  
Structural Components ◽  
Working Temperature ◽  
Different Temperatures ◽  
Positive Effect

Plastics are widely used in structural components where cyclic loads may cause fatigue failure. In particular, in some applications such as in vehicles, the working temperature may change and therefore the strength of the polymeric materials. In this work, the fatigue behavior of two thermoplastic materials (ABS and PC-ABS) at different temperatures has been investigated. In particular, three temperatures have been considered representing the working condition at room temperature, at low temperature (winter conditions), and high temperature (summer conditions and/or components close to the engine). Results show that high temperature have big impact on fatigue performance, while low temperatures may also have a slight positive effect.

scholarly journals Evaluation of pyrite and pyrrhotite in concretes

2016 ◽  
Vol 9 (3) ◽  
pp. 484-493 ◽  
Author(s):  
A. P. Marcelino ◽  
J. M. Calixto ◽  
A. G. Gumieri ◽  
M. C. Ferreira ◽  
C. L. Caldeira ◽  
...  
Keyword(s):  
Room Temperature ◽  
Iron Sulfide ◽  
Hydroelectric Power Plant ◽  
Hydroelectric Power ◽  
Rock Samples ◽  
Limit Value ◽  
Plant Area ◽  
Different Temperatures ◽  
Pyrite Content ◽  
One Year

ABSTRACT It is well known that aggregate characteristics can intensively interfere in concrete behavior especially when sulfides are presented in the aggregates. The lack of consensus to content limit value of these deleterious sulfur compounds in concrete structures for dams has motivated several investigations worldwide. Within this scenario, this work presents a methodology to evaluate the presence of pyrite and pyrrhotite in concretes produced with aggregates containing sulfides. For the study, rock samples from the Irapé hydroelectric power plant area in Minas Gerais (Brazil) were used. This plant was built in a geological site where the rock presented sulfide levels of at least 3%. These rock samples were first ground and then used as aggregates in mortars, which were, during almost one year, subjected to three different exposed conditions: temperature of 23° ± 2°C and relative humidity of 95 to 100%; calcium hydroxide solution diluted in water kept at two different temperatures: room temperature and 50° C. The presence and amount of pyrrhotite were obtained from a leaching process of the material (aggregate or mortar) in a solution of hydrochloric acid. This procedure allowed also the evaluation of the pyrite content. The results showed that the amount of pyrite has remained virtually constant over time in the three exposure situations. This finding indicates that sulfur limits in aggregates should be set according to the type of iron sulfide presented and not solely by the total amount of sulfur.

scholarly journals Water-Based Indium Tin Oxide Nanoparticle Ink for Printed Toluene Vapours Sensor Operating at Room Temperature

Sensors ◽  
2018 ◽  
Vol 18 (10) ◽  
pp. 3246 ◽  
Author(s):  
Jan Maslik ◽  
Ivo Kuritka ◽  
Pavel Urbanek ◽  
Petr Krcmar ◽  
Pavol Suly ◽  
...  
Keyword(s):  
Tin Oxide ◽  
Indium Tin Oxide ◽  
Room Temperature ◽  
Ambient Air ◽  
Protective Atmosphere ◽  
Baseline Drift ◽  
Nanoparticle Dispersions ◽  
Treatment Conditions ◽  
Water Based ◽  
Different Temperatures

This study is focused on the development of water-based ITO nanoparticle dispersions and ink-jet fabrication methodology of an indium tin oxide (ITO) sensor for room temperature operations. Dimensionless correlations of material-tool-process variables were used to map the printing process and several interpretational frameworks were re-examined. A reduction of the problem to the Newtonian fluid approach was applied for the sake of simplicity. The ink properties as well as the properties of the deposited layers were tested for various nanoparticles loading. High-quality films were prepared and annealed at different temperatures. The best performing material composition, process parameters and post-print treatment conditions were used for preparing the testing sensor devices. Printed specimens were exposed to toluene vapours at room temperature. Good sensitivity, fast responses and recoveries were observed in ambient air although the n-type response mechanism to toluene is influenced by moisture in air and baseline drift was observed. Sensing response inversion was observed in an oxygen and moisture-free N2 atmosphere which is explained by the charge-transfer mechanism between the adsorbent and adsorbate molecules. The sensitivity of the device was slightly better and the response was stable showing no drifts in the protective atmosphere.

scholarly journals Effect of epitaxial alignment on electron transport from quasi-two-dimensional iron silicide alpha-FeSi-=SUB=-2-=/SUB=- nanocrystals into p-Si(001)

2018 ◽  
Vol 52 (5) ◽  
pp. 523
Author(s):  
I.A. Tarasov ◽  
M.V. Rautskii ◽  
I.A. Yakovlev ◽  
M.N. Volochaev
Keyword(s):  
Electron Transport ◽  
Room Temperature ◽  
Molecular Beam ◽  
Schottky Barrier Height ◽  
Iron Silicide ◽  
Current Voltage Characteristic ◽  
Current Voltage ◽  
Basic Orientation ◽  
Different Temperatures ◽  
A Current

AbstractSelf-assembled growth of α-FeSi_2 nanocrystal ensembles on gold-activated and gold-free Si(001) surface by molecular beam epitaxy is reported. The microstructure and basic orientation relationship (OR) between the silicide nanocrystals and silicon substrate were analysed. The study reveals that utilisation of the gold as catalyst regulates the preferable OR of the nanocrystals with silicon and their habitus. It is shown that electron transport from α-FeSi2 phase into p-Si(001) can be tuned by the formation of (001)—or (111)—textured α-FeSi2 nanocrystals ensembles. A current-voltage characteristic of the structures with different preferable epitaxial alignment (α-FeSi_2(001)/Si(100) and α-FeSi_2(111)/Si(100)) shows good linearity at room temperature. However, it becomes non-linear at different temperatures for different ORs due to different Schottky barrier height governed by a particular epitaxial alignment of the α-FeSi_2/ p -Si interfaces.

Sign in / Sign up

Export Citation Format

Share Document