Improving the Photostabilization of Poly(vinyl chloride) Using 4-(benzylideneamino)benzenesulfonamide Tin Complex

2022 ◽  
Vol 16 (1) ◽  
pp. 23
Author(s):  
Hassan Ghani ◽  
Emad Yousif ◽  
Mohammed Kadhom ◽  
Waled Abdo Ahmed ◽  
Muhammad Rahimi Yusop ◽  
...  
Keyword(s):  
Weight Loss ◽  
Vinyl Chloride ◽  
Photo Degradation ◽  
Viscosity Change ◽  
Force Microscopy ◽  
Atomic Force ◽  
Poly Vinyl Chloride ◽  
Pvc Film ◽  
Before And After ◽  
The Impact

The photostabilization of poly (vinyl chloride) (PVC) film filled with an organotin complex in its structure was examined and compared with the blank PVC film. The organotin (IV) complex that contains 4-(benzylideneamino) benzenesulfonamide as a ligand was synthesized and applied as a PVC photostabilizer. The impact of the complex on the polymer was assessed by comparing the properties of the films with and without the complex, before and after irradiation, using Fourier transform infrared spectroscopy, weight loss, viscosity change, atomic force microscopy, and field emission scanning electron microscopy (FE-SEM). Results showed that the complex film had lower weight loss, gel content, and molecular weight deterioration than the plain PVC film. Also, surfaces of the complexes-filled films were smoother, less lumpy, and more homogeneous. These findings were obtained via the FE-SEM and light microscope images and confirmed by measuring the roughness factor. The organotin (IV) complex proved its activity in delaying the photo-degradation of PVC by several mechanisms. Ultimately, the Tin complex has effectively protected the PVC film against irradiation. The photostabilization of poly (vinyl chloride) (PVC) film filled with an organotin complex in its structure was examined and compared with the blank PVC film. The organotin (IV) complex that contains 4-(benzylideneamino) benzenesulfonamide as a ligand was synthesized and applied as a PVC photostabilizer. The impact of the complex on the polymer was assessed by comparing the properties of the films with and without the complex, before and after irradiation, using Fourier transform infrared spectroscopy, weight loss, viscosity change, atomic force microscopy, and field emission scanning electron microscopy (FE-SEM). Results showed that the complex film had lower weight loss, gel content, and molecular weight deterioration than the plain PVC film. Also, surfaces of the complexes-filled films were smoother, less lumpy, and more homogeneous. These findings were obtained via the FE-SEM and light microscope images and confirmed by measuring the roughness factor. The organotin (IV) complex proved its activity in delaying the photo-degradation of PVC by several mechanisms. Ultimately, the Tin complex has effectively protected the PVC film against irradiation.

scholarly journals Tin(IV) Compounds as Photo-Stabilizers for Irradiated Surfaces of Poly(Vinyl Chloride) Films

Surfaces ◽  
2021 ◽  
Vol 4 (4) ◽  
pp. 279-292
Author(s):  
Alaa Mohammed ◽  
Mohammed Kadhom ◽  
Emad Yousif
Keyword(s):  
Vinyl Chloride ◽  
Room Temperature ◽  
Uv Light ◽  
Weight Ratio ◽  
Force Microscopy ◽  
Content Change ◽  
Atomic Force ◽  
Poly Vinyl Chloride ◽  
Before And After ◽  
Scanning Electron

Dimethyl-organotin(IV) valsartan (Me2SnL2) and dichlorostannanediyl valsartan (SnL2Cl2) complexes were synthesized, characterized, and applied as Poly(vinyl chloride) (PVC) photo-stabilizers. The complexes were loaded within the PVC films in a weight ratio of 0.5%, and the modified films were irradiated to a UV light of 313 nm wavelength for 300 h at room temperature. The efficiency of the complexes-filled films was compared with the plain one and evaluated before and after irradiation by Fourier transform infrared spectroscopy, weight loss, gel content, change in viscosity, atomic force microscopy, and field emission scanning electron microscopy. The SnL2Cl2 complex had higher activity than the Me2SnL2 complex to retard the PVC’s photodegradation by several mechanisms.

scholarly journals The Morphology and Performance of Poly(Vinyl Chloride) Containing Melamine Schiff Bases against Ultraviolet Light

Molecules ◽  
2019 ◽  
Vol 24 (4) ◽  
pp. 803 ◽  
Author(s):  
Gamal El-Hiti ◽  
Mohammad Alotaibi ◽  
Ahmed Ahmed ◽  
Basheer Hamad ◽  
Dina Ahmed ◽  
...  
Keyword(s):  
Ultraviolet Light ◽  
Vinyl Chloride ◽  
Schiff Bases ◽  
Average Molecular Weight ◽  
Hydroxyl Group ◽  
Force Microscopy ◽  
Polymeric Surface ◽  
Atomic Force ◽  
Poly Vinyl Chloride ◽  
And Performance

Five Schiff bases derived from melamine have been used as efficient additives to reduce the process of photodegradation of poly(vinyl chloride) films. The performance of Schiff bases has been investigated using various techniques. Poly(vinyl chloride) films containing Schiff bases were irradiated with ultraviolet light and any changes in their infrared spectra, weight, and the viscosity of their average molecular weight were investigated. In addition, the surface morphology of the films was inspected using a light microscope, atomic force microscopy, and a scanning electron micrograph. The additives enhanced the films resistance against irradiation and the polymeric surface was much smoother in the presence of the Schiff bases compared with the blank film. Schiff bases containing an ortho-hydroxyl group on the aryl rings showed the greatest photostabilization effect, which may possibly have been due to the direct absorption of ultraviolet light. This phenomenon seems to involve the transfer of a proton as well as several intersystem crossing processes.

scholarly journals Photostabilization of Poly(vinyl chloride) by Organotin(IV) Compounds against Photodegradation

Molecules ◽  
2019 ◽  
Vol 24 (19) ◽  
pp. 3557 ◽  
Author(s):  
Angham G. Hadi ◽  
Khudheyer Jawad ◽  
Gamal A. El-Hiti ◽  
Mohammad Hayal Alotaibi ◽  
Ahmed A. Ahmed ◽  
...  
Keyword(s):  
Molecular Weight ◽  
Weight Loss ◽  
Vinyl Chloride ◽  
Room Temperature ◽  
Loss Reduction ◽  
Radical Scavengers ◽  
Poly Vinyl Chloride ◽  
Pvc Film ◽  
Surface Irregularities ◽  
Industrial Materials

Poly(vinyl chloride) (PVC), a polymer widely used in common household and industrial materials, undergoes photodegradation upon ultraviolet irradiation, leading to undesirable physicochemical properties and a reduced lifetime. In this study, four telmisartan organotin(IV) compounds were tested as photostabilizers against photodegradation. PVC films (40-µm thickness) containing these compounds (0.5 wt%) were irradiated with ultraviolet light at room temperature for up to 300 h. Changes in various polymeric parameters, including the growth of hydroxyl, carbonyl, and alkene functional groups, weight loss, reduction in molecular weight, and appearance of surface irregularities, were investigated to test the efficiency of the photostabilizers. The changes were more noticeable in the blank PVC film than in the films containing the telmisartan organotin(IV) compounds. These results reflect that these compounds effectively inhibit the photodegradation of PVC, possibly by acting as hydrogen chloride and radical scavengers, peroxide decomposers, and primary photostabilizers. The synthesized organotin(IV) complexes could be used as PVC additives to enhance photostability.

Surface roughness measurements of vanadium-contaminated fluidized cracking catalysts by atomic force microscopy

1996 ◽  
Vol 54 ◽  
pp. 866-867
Author(s):  
H. Kinney ◽  
M.L. Occelli ◽  
S.A.C. Gould
Keyword(s):  
Surface Roughness ◽  
Zeolite Y ◽  
Atomic Level ◽  
Microporous Structure ◽  
Contact Mode ◽  
Force Microscopy ◽  
Atomic Force ◽  
Before And After ◽  
Roughness Measurements ◽  
Cracking Catalysts

For this study we have used a contact mode atomic force microscope (AFM) to study to topography of fluidized cracking catalysts (FCC), before and after contamination with 5% vanadium. We selected the AFM because of its ability to well characterize the surface roughness of materials down to the atomic level. It is believed that the cracking in the FCCs occurs mainly on the catalysts top 10-15 μm suggesting that the surface corrugation could play a key role in the FCCs microactivity properties. To test this hypothesis, we chose vanadium as a contaminate because this metal is capable of irreversibly destroying the FCC crystallinity as well as it microporous structure. In addition, we wanted to examine the extent to which steaming affects the vanadium contaminated FCC. Using the AFM, we measured the surface roughness of FCCs, before and after contamination and after steaming.We obtained our FCC (GRZ-1) from Davison. The FCC is generated so that it contains and estimated 35% rare earth exchaged zeolite Y, 50% kaolin and 15% binder.

scholarly journals Extracellular Vesicles Analysis in the COVID-19 Era: Insights on Serum Inactivation Protocols towards Downstream Isolation and Analysis

Cells ◽  
2021 ◽  
Vol 10 (3) ◽  
pp. 544
Author(s):  
Roberto Frigerio ◽  
Angelo Musicò ◽  
Marco Brucale ◽  
Andrea Ridolfi ◽  
Silvia Galbiati ◽  
...  
Keyword(s):  
Extracellular Vesicles ◽  
Analytical Techniques ◽  
Heat Inactivation ◽  
Force Microscopy ◽  
Atomic Force ◽  
Droplet Pcr ◽  
Detergent Treatment ◽  
Routine Procedures ◽  
The Impact ◽  
Mirna Content

Since the outbreak of the COVID-19 crisis, the handling of biological samples from confirmed or suspected SARS-CoV-2-positive individuals demanded the use of inactivation protocols to ensure laboratory operators’ safety. While not standardized, these practices can be roughly divided into two categories, namely heat inactivation and solvent-detergent treatments. These routine procedures should also apply to samples intended for Extracellular Vesicles (EVs) analysis. Assessing the impact of virus-inactivating pre-treatments is therefore of pivotal importance, given the well-known variability introduced by different pre-analytical steps on downstream EVs isolation and analysis. Arguably, shared guidelines on inactivation protocols tailored to best address EVs-specific requirements will be needed among the analytical community, yet deep investigations in this direction have not yet been reported. We here provide insights into SARS-CoV-2 inactivation practices to be adopted prior to serum EVs analysis by comparing solvent/detergent treatment vs. heat inactivation. Our analysis entails the evaluation of EVs recovery and purity along with biochemical, biophysical and biomolecular profiling by means of a set of complementary analytical techniques: Nanoparticle Tracking Analysis, Western Blotting, Atomic Force Microscopy, miRNA content (digital droplet PCR) and tetraspanin assessment by microarrays. Our data suggest an increase in ultracentrifugation (UC) recovery following heat treatment; however, it is accompanied by a marked enrichment in EVs-associated contaminants. On the other hand, solvent/detergent treatment is promising for small EVs (<150 nm range), yet a depletion of larger vesicular entities was detected. This work represents a first step towards the identification of optimal serum inactivation protocols targeted to EVs analysis.

Structuring of Silicon Wafer Surfaces on the Sub-100 nm Scale by Hydrogen Plasma Treatments

2003 ◽  
Vol 788 ◽  
Author(s):  
R. Job ◽  
Y. Ma ◽  
A. G. Ulyashin
Keyword(s):  
Hydrogen Plasma ◽  
Structural Defects ◽  
Process Conditions ◽  
Force Microscopy ◽  
Czochralski Silicon ◽  
Atomic Force ◽  
Nano Structures ◽  
Plasma Treatments ◽  
The Impact ◽  
Wafer Surfaces

ABSTRACTHydrogen plasma treatments applied on standard Czochralski silicon (Cz Si) wafers cause a structuring of the surface regions on the sub-100 nm scale, i.e. a thin ‘nano-structured’ Si layer is created up to a depth of ∼ 150 nm. The formation of the ‘nano-structures’ and their evolution in dependence on the process conditions was studied. The impact of post-hydrogenation annealing on the morphology of the structural defects was studied up to 1200 °C. The H-plasma treated and annealed samples were analyzed at surface and sub-surface regions by scanning electron microscopy (SEM), atomic force microscopy (AFM), and μ-Raman spectroscopy.

scholarly journals The Physicochemical and Antibacterial Properties of Chitosan-Based Materials Modified with Phenolic Acids Irradiated by UVC Light

2021 ◽  
Vol 22 (12) ◽  
pp. 6472
Author(s):  
Beata Kaczmarek-Szczepańska ◽  
Marcin Wekwejt ◽  
Olha Mazur ◽  
Lidia Zasada ◽  
Anna Pałubicka ◽  
...  
Keyword(s):  
Thin Films ◽  
Antimicrobial Activity ◽  
Ferulic Acid ◽  
Phenolic Acid ◽  
Food Packaging ◽  
Antibacterial Properties ◽  
Force Microscopy ◽  
Atomic Force ◽  
Before And After

This paper concerns the physicochemical properties of chitosan/phenolic acid thin films irradiated by ultraviolet radiation with wavelengths between 200 and 290 nm (UVC) light. We investigated the preparation and characterization of thin films based on chitosan (CTS) with tannic (TA), caffeic (CA) and ferulic acid (FA) addition as potential food-packaging materials. Such materials were then exposed to the UVC light (254 nm) for 1 and 2 h to perform the sterilization process. Different properties of thin films before and after irradiation were determined by various methods such as Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), atomic force microscopy (AFM), differential scanning calorimeter (DSC), mechanical properties and by the surface free energy determination. Moreover, the antimicrobial activity of the films and their potential to reduce the risk of contamination was assessed. The results showed that the phenolic acid improving properties of chitosan-based films, short UVC radiation may be used as sterilization method for those films, and also that the addition of ferulic acid obtains effective antimicrobial activity, which have great benefit for food packing applications.

Characterization of X-ray irradiated graphene oxide coatings using X-ray diffraction, X-ray photoelectron spectroscopy, and atomic force microscopy

2013 ◽  
Vol 28 (2) ◽  
pp. 68-71 ◽  
Author(s):  
Thomas N. Blanton ◽  
Debasis Majumdar
Keyword(s):  
Atomic Force Microscopy ◽  
Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
High Energy ◽  
X Ray Diffraction ◽  
Carbon Phase ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Before And After

In an effort to study an alternative approach to make graphene from graphene oxide (GO), exposure of GO to high-energy X-ray radiation has been performed. X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM) have been used to characterize GO before and after irradiation. Results indicate that GO exposed to high-energy radiation is converted to an amorphous carbon phase that is conductive.

scholarly journals Фотофизические свойства тонких пленок перилена, модифицированного функциональными группами диангидрида и диимида тетракарбоновой кислоты

2021 ◽  
Vol 63 (9) ◽  
pp. 1437
Author(s):  
А.С. Комолов ◽  
Э.Ф. Лазнева ◽  
Е.В. Жижин ◽  
Э.К. Алиджанов ◽  
Ю.Д. Лантух ◽  
...  
Keyword(s):  
Charge Carrier ◽  
Band Gap ◽  
Charge Carrier Mobility ◽  
Dark Conductivity ◽  
Localized States ◽  
Semiconductor Films ◽  
Force Microscopy ◽  
Atomic Force ◽  
Before And After ◽  
Carrier Traps

The morphology of organic semiconductor films of perylenetetracarboxylic acid dianhydride (PTCDA) and perylenetetracarboxylic acid dibenzyl-diimide (N, N`-DBPTCDI) formed by thermal vacuum deposition was studied by atomic force microscopy. It was shown that annealing of films at 420 K leads to rearrangement of their structure and crystallization. The optical absorption spectra of the films under study were used to estimate the optical band gap. The temperature dependence of the dark conductivity of PTCDA and N, N-DBPTCDI films before and after annealing (Т = 420 K) was established. The values of the activation energy of charge carrier traps are determined. The computer simulation of the density of localized states in the band gap of the films studied was carried out using the photoconductivity spectra in the constant photocurrent mode. Model photovoltaic cells based on PTCDA / СuPc and N, N-DBPTCDI / СuPc structures were formed. The kinetics of decay of the interfacial photo-voltage of the cells prepared was measured using pulsed light as an excitation source. On the basis of the performed measurements, the charge carrier mobility values in the investigated semiconductor materials were estimated.

scholarly journals Deswelling Induced Morphological Changes in Dual pH and Temperature Responsive Ultra-Low Crosslinked Poly (N-Isopropyl Acrylamide)-Co-Acrylic Acid Microgels

2018 ◽  
Author(s):  
Molla Islam ◽  
Maddie Tumbarello ◽  
Andrew Lyon
Keyword(s):  
Light Scattering ◽  
Acrylic Acid ◽  
Morphological Changes ◽  
Scattering Data ◽  
Ionization State ◽  
Force Microscopy ◽  
Temperature Responsive ◽  
Atomic Force ◽  
Isopropyl Acrylamide ◽  
The Impact

<div>We demonstrated the deswelling induced morphological change in dual pH and Temperature responsive ultra-low crosslinked Poly (N-isopropyl acrylamide)-co-acrylic acid microgels. The responsivity with pH and temperature were studied by light scattering and atomic force microscopy. Light scattering data suggest that at pH 4.5 the microgels undergo multiple transitions associated with collapse of pNIPAm-rich segments and repulsion between the AAc-rich segments. The evolution of punctate structures around the periphery or throughout the whole microgels at pH 4.5 and 6.5 respectively was revealed by AFM, further illustrating the heterogeneous deswelling present in the ionized copolymer microgels.</div><div>The impact of this study and understanding how ionization state of copolymer dictates the overall structural properties of microgels will widen our understanding for their applications in biotechnology</div><div><b><br></b></div>

Sign in / Sign up

Export Citation Format

Share Document