Failure Analysis of Single-Bit Charge Loss after Stress and Studies on Silicon Dopant Profile

2016 ◽  
Author(s):  
Rong-Wei Gong ◽  
Hsiao-Tien Chang ◽  
Hui-Wen Chan ◽  
Lian-Feng Lee ◽  
Chih-Ching Shih ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Flash Memory ◽  
Degradation Process ◽  
Electrical Failure ◽  
Dopant Profile ◽  
Analysis Technique ◽  
Drain Side ◽  
Charge Loss ◽  
Selective Chemical ◽  
Tcad Simulation

Abstract The single-bit charge loss of flash memory after stress has been investigated using TEM with selective chemical etching and TCAD simulation for the effect of silicon dopant profile and electrical failure analysis technique. However, the abnormal dopant profile on the drain-side of the failing bit observed in the TEM does not match the leakage behavior from the simulation. A qualitative model for the degradation process is proposed based on the electrical failure analysis results, it is suggested that the hole generated by avalanche breakdown captured by oxide traps on the drain-side during the stress is the source of leakage current.

Application of Electro Optical Terahertz Pulse Reflectometry for Fault Localization and Defect Analysis

2017 ◽  
Author(s):  
Yi-Sheng Lin ◽  
Yu-Hsiang Hsiao ◽  
Shu-Hua Lee
Keyword(s):  
Failure Analysis ◽  
Semiconductor Industry ◽  
Fault Isolation ◽  
Defect Analysis ◽  
Wafer Level ◽  
Terahertz Pulse ◽  
Electrical Failure ◽  
Analysis Technique ◽  
Destructive Analysis ◽  
Non Destructive

Abstract Electro Optical Terahertz Pulse Reflectometry (EOTPR) is an E-FA (Electrical Failure Analysis) technique in the semiconductor industry for non-destructive electrical fault isolation for shorts, leakages and opens. This paper introduces the capability and presents several case studies identifying the physical location of defects where EOTPR is useful as a non-destructive analysis technique. In this paper, the methodology and application of EOTPR on open and short failure isolations in advanced 2.5D IC and wafer level packages (WLP) have been presented. The experimental results of P-FA (Physical Failure Analysis) verify the accuracy of the EOTPR system in determining the distance to defect.

Detection and Characterization of an Electrical Failure Induced during Laser Ablation of Packages

2008 ◽  
Author(s):  
P. Schwindenhammer ◽  
H. Murray ◽  
P. Descamps ◽  
P. Poirier
Keyword(s):  
Laser Ablation ◽  
Integrated Circuits ◽  
Failure Analysis ◽  
Ablation Process ◽  
Thermally Induced ◽  
Electrical Failure ◽  
Electrical Phenomenon ◽  
Semiconductor Packages ◽  
Complex Semiconductor

Abstract Decapsulation of complex semiconductor packages for failure analysis is enhanced by laser ablation. If lasers are potentially dangerous for Integrated Circuits (IC) surface they also generate a thermal elevation of the package during the ablation process. During measurement of this temperature it was observed another and unexpected electrical phenomenon in the IC induced by laser. It is demonstrated that this new phenomenon is not thermally induced and occurs under certain ablation conditions.

Advanced IR-OBIRCH Analysis Technique for High Isb Failure Analysis

2010 ◽  
Author(s):  
Kuo Hsiung Chen ◽  
Wen Sheng Wu ◽  
Yu Hsiang Shu ◽  
Jian Chan Lin
Keyword(s):  
Failure Analysis ◽  
Failure Mechanisms ◽  
Fault Localization ◽  
Resistance Change ◽  
The Real ◽  
Analysis Techniques ◽  
Analysis Technique ◽  
Leakage Failure ◽  
Failure Site

Abstract IR-OBIRCH (Infrared Ray – Optical Beam Induced Resistance Change) is one of the main failure analysis techniques [1] [2] [3] [4]. It is a useful tool to do fault localization on leakage failure cases such as poor Via or contact connection, FEoL or BEoL pattern bridge, and etc. But the real failure sites associated with the above failure mechanisms are not always found at the OBIRCH spot locations. Sometimes the real failure site is far away from the OBIRCH spot and it will result in inconclusive PFA Analysis. Finding the real failure site is what matters the most for fault localization detection. In this paper, we will introduce one case using deep sub-micron process generation which suffers serious high Isb current at wafer donut region. In this case study a BEoL Via poor connection is found far away from the OBIRCH spots. This implies that layout tracing skill and relation investigation among OBIRCH spots are needed for successful failure analysis.

Case Study in Fault Isolation of a Metal Short for Yield Enhancement

2010 ◽  
Author(s):  
Sarven Ipek ◽  
David Grosjean
Keyword(s):  
Failure Analysis ◽  
Failure Mechanism ◽  
Photon Emission ◽  
Fault Isolation ◽  
Yield Enhancement ◽  
Analysis Technique ◽  
Laser Signal ◽  
Signal Injection ◽  
Microscopy Techniques

Abstract The application of an individual failure analysis technique rarely provides the failure mechanism. More typically, the results of numerous techniques need to be combined and considered to locate and verify the correct failure mechanism. This paper describes a particular case in which different microscopy techniques (photon emission, laser signal injection, and current imaging) gave clues to the problem, which then needed to be combined with manual probing and a thorough understanding of the circuit to locate the defect. By combining probing of that circuit block with the mapping and emission results, the authors were able to understand the photon emission spots and the laser signal injection microscopy (LSIM) signatures to be effects of the defect. It also helped them narrow down the search for the defect so that LSIM on a small part of the circuit could lead to the actual defect.

Test Circuit Conditioning for Soft Defect Localization

2014 ◽  
Author(s):  
Kristopher D. Staller ◽  
Corey Goodrich
Keyword(s):  
Laser Beam ◽  
Failure Analysis ◽  
Signal Frequency ◽  
Dynamic Failure ◽  
The Third ◽  
Analysis Technique ◽  
Test Circuit ◽  
Defect Localization ◽  
Manual Input ◽  
Fast Dynamic

Abstract Soft Defect Localization (SDL) is a dynamic laser-based failure analysis technique that can detect circuit upsets (or cause a malfunctioning circuit to recover) by generation of localized heat or photons from a rastered laser beam. SDL is the third and seldom used method on the LSM tool. Most failure analysis LSM sessions use the endo-thermic mode (TIVA, XIVA, OBIRCH), followed by the photo-injection mode (LIVA) to isolate most of their failures. SDL is seldom used or attempted, unless there is a unique and obvious failure mode that can benefit from the application. Many failure analysts, with a creative approach to the analysis, can employ SDL. They will benefit by rapidly finding the location of the failure mechanism and forgoing weeks of nodal probing and isolation. This paper will cover circuit signal conditioning to allow for fast dynamic failure isolation using an LSM for laser stimulation. Discussions of several cases will demonstrate how the laser can be employed for triggering across a pass/fail boundary as defined by voltage levels, supply currents, signal frequency, or digital flags. A technique for manual input of the LSM trigger is also discussed.

Localization Techniques on a 0.15um CMOS Device: Charge Pump Failure Analysis

2002 ◽  
Author(s):  
Hui Pan ◽  
Thomas Gibson
Keyword(s):  
Failure Analysis ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Electrical Characterization ◽  
Charge Pump ◽  
Front Side ◽  
Pump Failure ◽  
Electrical Failure ◽  
Optical Proximity Correction ◽  
A Charge

Abstract In recent years, there have been many advances in the equipment and techniques used to isolate faults. There are many options available to the failure analyst. The available techniques fall into the categories of electrical, photonic, thermal and electron/ion beam [1]. Each technique has its advantages and its limitations. In this paper, we introduce a case of successful failure analysis using a combination of several fault localization techniques on a 0.15um CMOS device with seven layers of metal. It includes electrical failure mode characterization, front side photoemission, backside photoemission, Focused Ion Beam (FIB), Scanning Electron Microscope (SEM) and liquid crystal. Electrical characterization along with backside photoemission proved most useful in this case as a poly short problem was found to be causing a charge pump failure. A specific type of layout, often referred to as a hammerhead layout, and the use of Optical Proximity Correction (OPC) contributed to the poly level shorts.

scholarly journals Combine TEM with TCAD Simulation - A Novel Approach in Failure Analysis

2021 ◽  
Vol 27 (S1) ◽  
pp. 1548-1549
Author(s):  
Yu Zhang ◽  
Satish Kodali ◽  
Edmund Banghart ◽  
Travis Mitchell ◽  
Frieder Baumann
Keyword(s):  
Failure Analysis ◽  
Novel Approach ◽  
Tcad Simulation

scholarly journals Progressive Failure Analysis in Open-Hole Tensile Composite Laminates of Airplane Stringers Based on Tests and Simulations

2020 ◽  
Vol 11 (1) ◽  
pp. 185
Author(s):  
Jian Shi ◽  
Mingbo Tong ◽  
Chuwei Zhou ◽  
Congjie Ye ◽  
Xindong Wang
Keyword(s):  
Failure Analysis ◽  
Composite Laminates ◽  
Progressive Failure ◽  
Tensile Load ◽  
Fiber Failure ◽  
Stress Criterion ◽  
Progressive Failure Analysis ◽  
Analysis Technique ◽  
Open Hole ◽  
Failure Types

The failure types and ultimate loads for eight carbon-epoxy laminate specimens with a central circular hole subjected to tensile load were tested experimentally and simulated using two different progressive failure analysis (PFA) methodologies. The first model used a lamina level modeling based on the Hashin criterion and the Camanho stiffness degradation theory to predict the damage of the fiber and matrix. The second model implemented a micromechanical analysis technique coined the generalized method of cells (GMC), where the 3D Tsai–Hill failure criterion was used to govern matrix failure, and the fiber failure was dictated by the maximum stress criterion. The progressive failure methodology was implemented using the UMAT subroutine within the ABAQUS/implicit solver. Results of load versus displacement and failure types from the two different models were compared against experimental data for the open hole laminates subjected to tensile displacement load. The results obtained from the numerical simulation and experiments showed good agreement. Failure paths and accurate damage contours for the tested specimens were also predicted.

SRAM Bitcell Defect Identification Methodology Using Electrical Failure Analysis Data

2020 ◽  
Author(s):  
Hyungtae Kim ◽  
Geonho Kim ◽  
Yunrong Li ◽  
Jinyong Jeong ◽  
Youngdae Kim
Keyword(s):  
Failure Analysis ◽  
Technology Development ◽  
New Technology ◽  
Random Access ◽  
Analysis Data ◽  
Test Method ◽  
Design For Test ◽  
Defect Identification ◽  
Electrical Failure ◽  
Efficient Test

Abstract Static Random Access Memory (SRAM) has long been used for a new technology development vehicle because it is sensitive to process defects due to its high density and minimum feature size. In addition, failure location can be accurately predicted because of the highly structured architecture. Thus, fast and accurate Failure Analysis (FA) of the SRAM failure is crucial for the success of new technology learning and development. It is often quite time consuming to identify defects through conventional physical failure analysis techniques. In this paper, we present an advanced defect identification methodology for SRAM bitcell failures with fast speed and high accuracy based on the bitcell transistor analog characteristics from special design for test (DFT) features, Direct Bitcell Access (DBA). This technique has the advantage to shorten FA throughput time due to a time efficient test method and an intuitive failure analysis method based on Electrical Failure Analysis (EFA) without destructive analysis. In addition, all the defects in a wafer can be analyzed and improved simultaneously utilizing the proposed defect identification methodology. Some successful case studies are also discussed to demonstrate the efficiency of the proposed defect identification methodology.

Sign in / Sign up

Export Citation Format

Share Document