scholarly journals Research on a Piezoelectric Pump with Flexible Valves

2021 ◽  
Vol 11 (7) ◽  
pp. 2909
Author(s):  
Weiqing Huang ◽  
Liyi Lai ◽  
Zhenlin Chen ◽  
Xiaosheng Chen ◽  
Zhi Huang ◽  
...  
Keyword(s):  
Flow Rate ◽  
Fluid Transport ◽  
Smooth Transition ◽  
Driving Voltage ◽  
Piezoelectric Pump ◽  
Venous Valve ◽  
Output Pressure ◽  
Small Flow ◽  
Working Principle ◽  
Opening And Closing

Imitating the structure of the venous valve and its characteristics of passive opening and closing with changes in heart pressure, a piezoelectric pump with flexible valves (PPFV) was designed. Firstly, the structure and the working principle of the PPFV were introduced. Then, the flexible valve, the main functional component of the pump, was analyzed theoretically. Finally, an experimental prototype was manufactured and its performance was tested. The research proves that the PPFV can achieve a smooth transition between valved and valveless by only changing the driving signal of the piezoelectric (PZT) vibrator. The results demonstrate that when the driving voltage is 100 V and the frequency is 25 Hz, the experimental flow rate of the PPFV is about 119.61 mL/min, and the output pressure is about 6.16 kPa. This kind of pump can realize the reciprocal conversion of a large flow rate, high output pressure, and a small flow rate, low output pressure under the electronic control signal. Therefore, it can be utilized for fluid transport and pressure transmission at both the macro-level and the micro-level, which belongs to the macro–micro combined component.

scholarly journals Improving Output Performance of a Resonant Piezoelectric Pump by Adding Proof Masses to a U-Shaped Piezoelectric Resonator

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 500
Author(s):  
Jian Chen ◽  
Wenzhi Gao ◽  
Changhai Liu ◽  
Liangguo He ◽  
Yishan Zeng
Keyword(s):  
Flow Rate ◽  
Maximum Flow ◽  
Working Fluid ◽  
Driving Voltage ◽  
Piezoelectric Resonator ◽  
Piezoelectric Pump ◽  
Compact Structure ◽  
Output Performance ◽  
Volume Efficiency ◽  
Working Efficiency

This study proposes the improvement of the output performance of a resonant piezoelectric pump by adding proof masses to the free ends of the prongs of a U-shaped piezoelectric resonator. Simulation analyses show that the out-of-phase resonant frequency of the developed resonator can be tuned more efficiently within a more compact structure to the optimal operating frequency of the check valves by adjusting the thickness of the proof masses, which ensures that both the resonator and the check valves can operate at the best condition in a piezoelectric pump. A separable prototype piezoelectric pump composed of the proposed resonator and two diaphragm pumps was designed and fabricated with outline dimensions of 30 mm × 37 mm × 54 mm. Experimental results demonstrate remarkable improvements in the output performance and working efficiency of the piezoelectric pump. With the working fluid of liquid water and under a sinusoidal driving voltage of 298.5 Vpp, the miniature pump can achieve the maximum flow rate of 2258.9 mL/min with the highest volume efficiency of 77.1% and power consumption of 2.12 W under zero backpressure at 311/312 Hz, and the highest backpressure of 157.3 kPa under zero flow rate at 383 Hz.

Development of a novel piezoelectric-actuated inertial pump using bionic valve

2021 ◽  
pp. 1045389X2097828
Author(s):  
Ji Ding ◽  
Yi Cao ◽  
Quanqu Chen ◽  
Jingshi Dong ◽  
Zhi Xu ◽  
...  
Keyword(s):  
Small Diameter ◽  
Flow Characteristics ◽  
Inertial Force ◽  
Maximum Output ◽  
Piezoelectric Pump ◽  
Flow Area ◽  
Response Characteristics ◽  
Tilting Angle ◽  
Small Flow ◽  
Working Principle

Sampling fluids from the small-diameter deep pipeline is a challenging problem. In this paper, a very simple, piezoelectric-actuated inertial pump (PIP) is developed using a bionic valve to solve these problems. The PIP consists of simple components, including a cantilever beam piezoelectric actuator, a hard tube, and a bionic valve made of silicone. The fluid is driven by the inertial force generated in the vibration process of the tube. A new bionic valve inspired by a heart valve has been designed which has the advantages of small flow resistance and large flow area. The authors described the working principle of PIP in detail, established the flow characteristics model of the bionic valve, and used COMSOL Multiphysics to analyze the characteristics of the bionic valve. By comparing the response characteristics of the bionic valve with different tilt angles, the optimal Angle was obtained. Finally, the experimental and simulation results were compared, and the basic performance of PIP was tested. The experimental results showed that: When the tilting angle was 45° and the valve hole diameter was 6 mm, when the voltage was 98 V and the frequency was 24.5 Hz, the maximum output flow of the piezoelectric pump was 170.25 ml/min.

scholarly journals Equivalent Circuit Modeling for a Valveless Piezoelectric Pump

Sensors ◽  
2018 ◽  
Vol 18 (9) ◽  
pp. 2881 ◽  
Author(s):  
Jianhui Zhang ◽  
Yuan Wang ◽  
Jun Huang
Keyword(s):  
Equivalent Circuit ◽  
Flow Rate ◽  
Equivalent Circuit Model ◽  
Circuit Model ◽  
Experimental Results ◽  
Driving Voltage ◽  
Piezoelectric Pump ◽  
Pump System ◽  
Field Problem ◽  
Valveless Piezoelectric Pump

Various kinds of the models had been proposed to explain the relationship between the performance and the structural parameters of valveless piezoelectric pumps, so as to evaluate the functional performance such devices. Among the models, the equivalent circuit model, which converts the multi-field problem of a valveless piezoelectric pump system into a simple circuit problem, is the most simple and clear one. Therefore, the proposed structure and working principle of the valveless piezoelectric pump with multistage Y-shape treelike bifurcate tubes are analyzed; then, the equivalent circuit model of the valveless piezoelectric pump is established based on the working principles of this pump and liquid-electric analogy theory. Finally, an experimental study of the pump is carried out, with a comparative analysis of the experimental results and the simulation results of the generated equivalent circuit. The experimental results show that with a driving voltage of 100 V and frequency of 6 Hz, the maximum flow rate of the valveless piezoelectric pump is 1.16 mL/min. Meanwhile, the output current of equivalent circuit also reaches its peak at the frequency of 6 Hz, therefore, indicating a good predictive ability of this model in calculating the maximum output flow rate and best working frequency of valveless piezoelectric pumps.

Modeling and Simulation of a New Type Intelligent Gas Pressure Regulator

2014 ◽  
Vol 721 ◽  
pp. 191-194
Author(s):  
Yi Tong Wang ◽  
Jun Gong Ma
Keyword(s):  
Remote Control ◽  
Flow Rate ◽  
Gas Pressure ◽  
Mathematics Model ◽  
Pressure Regulator ◽  
Output Pressure ◽  
Centralized Management ◽  
Model And Simulation ◽  
New Type ◽  
Working Principle

In the view of the traditional purely mechanical regulator’s disadvantage, this paper proposed a new type intelligent gas pressure regulator. Its advantage is the ability to achieve accurate output pressure, remote control and centralized management. It can resist the disturbance of inlet pressure and flow rate changes. In this paper, we introduce the regulator’s structure, working principle, mathematics model and simulation model. According to the simulation result, it can basically meet the working demand.

scholarly journals Investigation on the Influence of Design Parameters of Streamline Flow Tubes on Pump Performance

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Kan Bian ◽  
Zhi Huang ◽  
Jietao Dai ◽  
Fan Zhang ◽  
Xiaosheng Chen ◽  
...  
Keyword(s):  
Flow Rate ◽  
Structure Design ◽  
Simulation Software ◽  
Smooth Transition ◽  
Design Parameters ◽  
Streamline Flow ◽  
Piezoelectric Pump ◽  
Conservation Of Energy ◽  
Pump Performance ◽  
Valveless Piezoelectric Pump

Studies have shown that the valveless piezoelectric pump with streamline flow tubes (VPPSFTs) can increase the flow rate while reducing the vortex, which has a broad application prospect and conforms to the huge potential demand in the fields of medical treatment, sanitation, and health care. The flow runner of the VPPSFT was designed as two segments with a smooth transition between the hyperbola segment and the arc segment. However, the effect of the radius of the arc segment on pump performance is not clear. Therefore, three groups of VPPSFT with arc segments of different curvature radii were designed in this study, and the influence of curvature radius of arc segment on the pump performance was explored. On the basis of the theoretical analysis of fluid continuity and conservation of energy, the structure of VPPSFT was designed, the experimental test was carried out, and the finite element simulation software was used for numerical analysis. The results show that the output performance increases with the increase in the radius of the arc segment, and the maximum flow rate was 116.78 mL/min. The amplitude and the flow rate are almost the same trend as the frequency. This study improves the performance of the valveless piezoelectric pump and provides reference for the structure design of VPPSFT.

A piezoelectric micro gas compressor with parallel-serial hybrid chambers

2021 ◽  
pp. 1045389X2110639
Author(s):  
Song Chen ◽  
Zhen He ◽  
Chaoping Qian ◽  
Jianping Li ◽  
Zhonghua Zhang ◽  
...  
Keyword(s):  
Flow Rate ◽  
Maximum Flow ◽  
Stage I ◽  
Stage Ii ◽  
Driving Voltage ◽  
Driving Frequency ◽  
Output Pressure ◽  
New Ideas ◽  
Further Development ◽  
Large Flow

A piezoelectric micro gas compressor with parallel-serial hybrid chambers (PMGCPS) is presented, which consists of two compression stages of stage I and stage II. The stage I is composed of two piezoelectric driving units connected in parallel, while stage II is composed of a piezoelectric driving unit, forming an integral tower compression structure. Based on the tower compression structure, the PMGCPS owns the dual advantages of large flow rate and high output pressure. The prototype of PMGCPS is designed and manufactured. The driving frequency and voltage characteristics of PMGCPS are experimented. Under the driving frequency of 300 Hz and the driving voltage of 300 Vpp, the maximum flow rate and output pressure of PMGCPS is 795.6 mL/min and 13.4 kPa, respectively. PMGCPS provides new ideas for the further development of piezoelectric micro gas compressor.

scholarly journals Numerical simulation and experimental study on valveless piezoelectric pump with triangular obstacles

2021 ◽  
Vol 2083 (2) ◽  
pp. 022028
Author(s):  
Yeming Sun ◽  
Yu Wang ◽  
Yiwei Wang
Keyword(s):  
Numerical Simulation ◽  
Flow Rate ◽  
Flow Resistance ◽  
Reverse Flow ◽  
Maximum Output ◽  
Driving Voltage ◽  
Driving Frequency ◽  
Piezoelectric Pump ◽  
Valveless Pump ◽  
Valveless Piezoelectric Pump

Abstract A valve less piezoelectric pump with triangular obstacles is designed and manufactured, which uses piezoelectric vibrator as power source. The working principle and theoretical flow rate of the valveless piezoelectric pump are analyzed, and its flow rate expression is derived. The flow resistance characteristics of triangular obstacles are simulated by numerical simulation. Based on the mass fraction distribution of liquid water, the forward and reverse flow resistance of triangular obstacles and the influence of triangular obstacles on pumping capacity are analyzed. Finally, two groups of test prototypes of the valveless pump are made by using the engraving machine, and the flow measurement test is carried out. The experimental results show that the valveless piezoelectric pump with triangular obstacles can realize the valveless pumping function, and the pumping flow per unit time increases with the increase of triangular obstacles in the channel, and decreases with the increase of the distance between triangular obstacles and the channel. When the driving voltage is 140V and the driving frequency is 10Hz, the maximum output flow of the piezoelectric pump is 16.26ml/min.

On-Line Monitoring System for Monitoring SO2 in Fumes (1) — Monitoring Subsystem for SO2 Mass Concentration

2011 ◽  
Vol 422 ◽  
pp. 296-299
Author(s):  
Shi Long Wang ◽  
Li Na Wang ◽  
Hong Bo Wang ◽  
Yong Hui Cai
Keyword(s):  
Flow Velocity ◽  
Monitoring System ◽  
Flow Rate ◽  
Mass Concentration ◽  
National Monitoring ◽  
Monitoring Result ◽  
Short Period ◽  
On Line ◽  
Working Principle

In order to achieve the target of controlling SO2 emissions in fumes in a short period of time in China, a SO2 on-line monitoring system (CEMS) has been developed by the authorased on the principle of electrochemistry. This system consists of two subsystems: (1) SO2 mass concentration monitoring and (2) SO2 flow velocity and flow rate monitoring. In the paper, the procedure of system and working principle and method of SO2 mass concentration monitoring subsystem are described in detail (SO2 flow velocity and flow rate monitoring subsystem is described by another paper).Two subsystems work synchronously to monitor and calculate the SO2 emissions, then the on-line monitoring of SO2 emissions is achieved. Through experiment and testing, monitoring result of the system is stable and reliable, which has reached the national monitoring standards and passed the appraisal.

Experiment analysis of high output pressure piezoelectric pump with straight arm wheeled check valve

2021 ◽  
pp. 1045389X2098700
Author(s):  
Lipeng He ◽  
Xiaoqiang Wu ◽  
Zheng Zhang ◽  
Zhe Wang ◽  
Bangcheng Zhang ◽  
...  
Keyword(s):  
Chemical Analysis ◽  
Energy Loss ◽  
Check Valve ◽  
Experimental Results ◽  
Piezoelectric Pump ◽  
Output Pressure ◽  
Pressure Characteristic ◽  
Analysis System ◽  
Experiment Analysis ◽  
High Output

Piezoelectric pumps are applied in many fields, such as chemical analysis system and fluid pumping systems. Piezoelectric pumps with high output pressure can meet the needs of more fields. This article introduces the design and fabrication of a high output pressure piezoelectric pump with straight arm wheeled check valve. In this paper, the influence of straight arm wheeled check valve on the output pressure of piezoelectric pump is deeply discussed from the aspect of energy loss. This study investigated the effect of valve arm number ( N = 2, 3,4, and 5), the valve arm width ( W = 0.8, 1.0, and 1.2 mm), and the valve arm length ( L = 1.92, 2.02, and 2.12 mm) on the output pressure of piezoelectric pump. The output pressure characteristic of straight arm wheeled check valve piezoelectric pump with different valve parameters is obtained by experiment. Experimental results show that when N = 4, W = 1.0 mm, L = 2.02 mm, the output pressure of the straight arm wheeled check valve piezoelectric pump has the best output pressure of 27.41 kPa at 220 V and 85 Hz. This study provides a reference for the further application of piezoelectric pumps in fluid pumping field.

Optimization of Inlet Ring Groove Arrangement for Suppression of Unstable Flow in a Centrifugal Impeller

2005 ◽  
Author(s):  
Masahiro Ishida ◽  
Daisaku Sakaguchi ◽  
Hironobu Ueki
Keyword(s):  
Flow Rate ◽  
The Other ◽  
Centrifugal Impeller ◽  
Shape Parameters ◽  
Unstable Flow ◽  
Ring Groove ◽  
Flow Rates ◽  
Small Flow ◽  
Specific Speed ◽  
Large Flow

An optimization of the inlet ring groove arrangement has been pursued in the present study for obtaining better impeller characteristics and a wider operation range at both small and large flow rates in a high specific speed type centrifugal impeller with inducer. The effects of the shape parameters with respect to the inlet ring groove on the impeller characteristic and the flow incidence were analyzed mainly based on numerical simulations, but also compared to the experimental results. At small flow rates, a significant improvement in the impeller characteristic is achieved due to reduction in the excessive-positive flow incidence by optimizing both location and width of the rear groove near the inducer tip throat. On the other hand, the impeller characteristic is improved at large flow rates by implementing the corner radius at the rear groove edge and by placing another front ring groove in the suction pipe. As a result, by the optimized configuration of the front and rear ring grooves, the unstable flow range of the test impeller can be reduced by about 50% without deterioration of the impeller characteristic even at the 125% flow rate.

Sign in / Sign up

Export Citation Format

Share Document