scholarly journals Morphology Study on Inclusion Modifications Using Mg–Ca Treatment in Resulfurized Special Steel

Materials ◽  
2019 ◽  
Vol 12 (2) ◽  
pp. 197 ◽  
Author(s):  
Ping Shen ◽  
Jianxun Fu
Keyword(s):  
Fatigue Life ◽  
Energy Dispersive Spectrometer ◽  
Hot Forging ◽  
Laboratory Studies ◽  
Complex Inclusion ◽  
Special Steel ◽  
Low Aspect Ratio ◽  
Mg Content ◽  
Statistical Results ◽  
Scanning Electron

In resulfurized special steel, MnS and Al2O3 are two main inclusions that deteriorate fatigue life and machinability. It is important that these two inclusions should be well controlled to increase steel quality and usage performance. In the present study, a Mg–Ca treatment was employed to modify the MnS and Al2O3 inclusions in resulfurized steels to reduce detrimental effects on fatigue life and machinability. In the laboratory study, Ni–Mg alloy was added to 16MnCrS5 and 49MnVS3 steels. Both Al2O3 and CaO–Al2O3 were gradually modified to MgO·Al2O3 and MgO, being surrounded by MnS, that is, a complex inclusion with an oxide core and sulfide outer layer was formed. The amount of the complex inclusion increased with Mg content. In the hot forging experiment, non-Mg treated inclusions were in the morphology of long strip, while those with Mg treatment were seen to be less deformed with spherical morphology of low aspect ratio in which case inclusions had less effect on steel mechanical properties. The Mg–Ca treatment was also applied to the manufacture of resulfurized special steel in steel plants. The scanning electron microscope–energy dispersive spectrometer and statistical results agreed well with those in the laboratory studies.

Microstructure and microanalysis of sintered Fe-Nd-B permanent magnets

1990 ◽  
Vol 48 (4) ◽  
pp. 990-991
Author(s):  
Mahesh Chandramouli
Keyword(s):  
Electron Microscope ◽  
Liquid Phase ◽  
Permanent Magnets ◽  
Phase Distribution ◽  
Energy Dispersive Spectrometer ◽  
Nucleation And Growth ◽  
Liquid Phase Sintering ◽  
Domain Wall Energy ◽  
Oxide Phases ◽  
Scanning Electron

Magnetization reversal in sintered Fe-Nd-B, a complex, multiphase material, occurs by nucleation and growth of reverse domains making the isolation of the ferromagnetic Fe14Nd2B grains by other nonmagnetic phases crucial. The magnets used in this study were slightly rich in Nd (in comparison to Fe14Nd2B) to promote the formation of Nd-oxides at multigrain junctions and incorporated Dy80Al20 as a liquid phase sintering addition. Dy has been shown to increase the domain wall energy thus making nucleation more difficult while Al is thought to improve the wettability of the Nd-oxide phases.Bulk polished samples were examined in a JEOL 35CF scanning electron microscope (SEM) operated at 30keV equipped with a Be window energy dispersive spectrometer (EDS) detector in order to determine the phase distribution.

scholarly journals Extraction of Boron from Ludwigite Ore: Mechanism of Soda-Ash Roasting of Lizardite and Szaibelyite

Minerals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 533 ◽  
Author(s):  
Xin Zhang ◽  
Guanghui Li ◽  
Jinxiang You ◽  
Jian Wang ◽  
Jun Luo ◽  
...  
Keyword(s):  
Sodium Carbonate ◽  
Energy Dispersive Spectrometer ◽  
Low Grade ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Selective Activation ◽  
X Ray ◽  
Shed Light ◽  
Soda Ash ◽  
Scanning Electron

Ludwigite ore is a typical low-grade boron ore accounting for 58.5% boron resource of China, which is mainly composed of magnetite, lizardite and szaibelyite. During soda-ash roasting of ludwigite ore, the presence of lizardite hinders the selective activation of boron. In this work, lizardite and szaibelyite were prepared and their soda-ash roasting behaviors were investigated using thermogravimetric-differential scanning calorimetry (TG-DSC), X-ray diffraction (XRD), and scanning electron microscope and energy dispersive spectrometer (SEM-EDS) analyses, in order to shed light on the soda-ash activation of boron within ludwigite ore. Thermodynamics of Na2CO3-MgSiO3-Mg2SiO4-Mg2B2O5 via FactSage show that the formation of Na2MgSiO4 was preferential for the reaction between Na2CO3 and MgSiO3/Mg2SiO4. While, regarding the reaction between Na2CO3 and Mg2B2O5, the formation of NaBO2 was foremost. Raising temperature was beneficial for the soda-ash roasting of lizardite and szaibelyite. At a temperature lower than the melting of sodium carbonate (851 °C), the soda-ash roasting of szaibelyite was faster than that of lizardite. Moreover, the melting of sodium carbonate accelerated the reaction between lizardite with sodium carbonate.

Study on the Formation of Nanometer Silver Sol by Micro Arc Discharge

2014 ◽  
Vol 490-491 ◽  
pp. 8-13
Author(s):  
Jing Yang ◽  
Zhi Yu Yan ◽  
Bing Sun ◽  
Qiao Min Wang
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Electrolyte Solution ◽  
Sodium Citrate ◽  
Preparation Method ◽  
Arc Discharge ◽  
Energy Dispersive Spectrometer ◽  
Original Size ◽  
Stabilizer Type ◽  
Scanning Electron

A preparation of nanometer silver sol by micro arc discharge has been study here through the reduction of Ag3PO4. Sodium citrate and polyvinylpyrrolidone were added respectively into the electrolyte as stabilizer. The results show that, the Ag3PO4 concentration, stabilizer type and concentration have great impacts on the formation of the nanometer silver sol. By means of UV-VIS extinction spectrophotometer, scanning electron microscope and energy dispersive spectrometer, it is found that the solid powder extracted from the electrolyte solution after discharge is the aggregation of the silver formed in the solution and their original size maybe less than 20nm. Nanometer silver with smaller size and narrower size distribution can be obtained with sodium citrate as stabilizer than with polyvinylpyrrolidone. But the latter has higher conversion rate. From this experiment, we found that micro arc discharge can be a rapid, stable preparation method of nanometer silver sol.

The Study of Electroless Ni-P and Ni-P-PTFE Coating on Steel Tire Mold

2012 ◽  
Vol 501 ◽  
pp. 316-320
Author(s):  
Jian Zhang Guo ◽  
Bin Xu
Keyword(s):  
Wear Resistance ◽  
Corrosion Resistance ◽  
Pore Structure ◽  
Energy Dispersive Spectrometer ◽  
Salt Spray ◽  
Amorphous Structure ◽  
Carbon Steels ◽  
Electrochemical System ◽  
Electroless Ni ◽  
Scanning Electron

In order to improve the surface property of the steel tire mold, carbon steels were processed by electroless Ni-P and Ni-P-PTFE under contrast experiment. The coatings were characterized by Scanning Electron Microscopy (SEM) and Energy Dispersive Spectrometer (EDS). The wear resistance and corrosion resistance of the coatings were explored by tribometer, salt spray cabinet and advanced electrochemical system. The experimental results showed that the Ni-P coating was amorphous structure, and the Ni-P-PTFE coating was micro-pore structure; The wear resistance of Ni-P-PTFE coating was superior to Ni-P coating; In view of the micro-pore structure, the corrosion resistance of Ni-P-PTFE coating was worse than Ni-P coating, but they were all superior to carbon steels, and the service life of the steel tire mold were improved.

scholarly journals Possible source of ancient carbon in phytolith concentrates from harvested grasses

2012 ◽  
Vol 9 (5) ◽  
pp. 1873-1884 ◽  
Author(s):  
G. M. Santos ◽  
A. Alexandre ◽  
J. R. Southon ◽  
K. K. Treseder ◽  
R. Corbineau ◽  
...  
Keyword(s):  
Plant Tissue ◽  
Atmospheric Carbon Dioxide ◽  
Energy Dispersive Spectrometer ◽  
Nutrient Acquisition ◽  
Published Data ◽  
Plant Nutrient ◽  
Before Present ◽  
Sem Images ◽  
Carbon Dioxide Co2 ◽  
Scanning Electron

Abstract. Plants absorb and transport silicon (Si) from soil, and precipitation of Si within the living plants results in micrometric amorphous biosilica particles known as phytoliths. During phytolith formation, a small amount of carbon (<2%) can become occluded in the silica structure (phytC) and therefore protected from degradation by the environment after plant tissue decomposition. Since the major C source within plants is from atmospheric carbon dioxide (CO2) via photosynthesis, the current understanding is that the radiocarbon (14C) content of phytC should reflect the 14C content of atmospheric CO2 at the time the plant is growing. This assumption was recently challenged by 14C data from phytoliths extracted from living grasses that yielded ages of several thousand years (2–8 kyr BP; in radiocarbon years "Before Present" (BP), "Present" being defined as 1950). Because plants can take up small amounts of C of varying ages from soils (e.g., during nutrient acquisition), we hypothesized that this transported C within the plant tissue could be attached to or even embedded in phytoliths. In this work, we explore this hypothesis by reviewing previously published data on biosilica mineralization and plant nutrient acquisition as well as by evaluating the efficiency of phytolith extraction protocols from scanning electron microscope (SEM) images and energy dispersive spectrometer (EDS) analyses from harvested grasses phytolith concentrates. We show that current extraction protocols are inefficient since they do not entirely remove recalcitrant forms of C from plant tissue. Consequently, material previously measured as "phytC" may contain at least some fraction of soil-derived C (likely radiocarbon-old) taken up by roots. We also suggest a novel interpretation for at least some of the phytC – which enters via the root pathway during nutrient acquisition – that may help to explain the old ages previously obtained from phytolith concentrates.

scholarly journals Calorimetric study on Bi-Cu-Sn alloys

2019 ◽  
Vol 38 (2019) ◽  
pp. 541-546
Author(s):  
Jolanta Romanowska
Keyword(s):  
Differential Scanning Calorimetry ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Temperature Interval ◽  
Energy Dispersive Spectrometer ◽  
Energy Dispersive ◽  
Calorimetric Study ◽  
Calorimetric Investigation ◽  
Scanning Calorimetry ◽  
Scanning Electron

AbstractThe paper presents results of calorimetric investigation of the Bi-Cu-Sn system by means of differential scanning calorimetry (DSC) at the temperature interval 25-1250∘C, Values of liquidus, solidus and invariant reactions temperatures, as well as melting enthalpies of the selected alloys were determined. Microstructure investigation of the alloys were performed by the use of a scanning electron microscope (SEM) equipped with an energy-dispersive spectrometer (EDS).

scholarly journals Effect of Cerium on the Microstructure and Inclusion Evolution of C-Mn Cryogenic Vessel Steels

Materials ◽  
2021 ◽  
Vol 14 (18) ◽  
pp. 5262
Author(s):  
Liping Wu ◽  
Jianguo Zhi ◽  
Jiangshan Zhang ◽  
Bo Zhao ◽  
Qing Liu
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Heterogeneous Nucleation ◽  
Energy Dispersive Spectrometer ◽  
Energy Dispersive ◽  
Vessel Steel ◽  
Cryogenic Vessel ◽  
Central Segregation ◽  
Scanning Electron

The effects of Cerium (Ce) were studied on the casting slab quality, microstructure, and inclusion evolution of cryogenic vessel steel. An optical metallographic microscope, scanning electron microscope, energy dispersive spectrometer, and Thermo-calc thermodynamic software were used for characterization and analysis. The results indicated that the central segregation was significantly improved after adding Ce and reached the lowest level when the content of Ce was 0.0009 wt.%. Meanwhile, the presence of Ce reduces the size of ferrite and improves pearlite morphology. Ce also enables the modification of Al2O3 and MnS + Ti4C2S2 inclusions into ellipsoid CeAlO3 and spherical Ce2O2S + Ti4C2S2 composite inclusions, respectively, which are easier to remove. The formed Ce2O2S inclusions are fine and can work as heterogeneous nucleation points to refine the microstructure of steel.

scholarly journals Microstructural and Fracture Surface Study of Friction Stir Welded AA5082-AA7075 Butt Joints

2020 ◽  
Vol 5 (1) ◽  
pp. 49-56
Author(s):  
Gaurav Kumar ◽  
◽  
Rajeev Kumar ◽  
Ratnesh Kumar
Keyword(s):  
Tensile Strength ◽  
Fatigue Life ◽  
Fracture Surface ◽  
Microstructural Analysis ◽  
Butt Joints ◽  
Friction Stir ◽  
Three Samples ◽  
Mode Of Failure ◽  
Microstructural Behavior ◽  
Scanning Electron

In this study, experiments were performed to analyze the fracture surface and microstructural behavior of friction stir welded (FSW) AA5082-AA7075butt joints. Three samples at varying speeds and constant feed were prepared to identify optimum tool speed to produce FSW AA5082-AA7075 butt joints having maximum tensile strength and fatigue life. A scanning electron microscope (SEM) was used to analyze microstructure and fracture surfaces. The samples prepared exhibited a considerable difference in their fatigue life and tensile strength. Microstructural analysis showed the refinement of grains present in the stir zone (SZ), also known as the weld nugget, and thermo-mechanically affected zone (TMAZ). The study of the fracture surface showed that the mode of failure was ductile in nature

Effect of Roughness on Fatigue Life of Open Holes

2007 ◽  
Vol 348-349 ◽  
pp. 757-760 ◽  
Author(s):  
Yong Shou Liu ◽  
Jun Liu ◽  
Xiao Jun Shao ◽  
Zhu Feng Yue
Keyword(s):  
Surface Roughness ◽  
Fatigue Life ◽  
Fatigue Testing ◽  
Fracture Morphology ◽  
Internal Crack ◽  
Corner Crack ◽  
Fatigue Lifetime ◽  
Crack Type ◽  
Open Hole ◽  
Scanning Electron

The fatigue testing of the specimen with a central open hole was carried out to investigate the influence of the surface roughness on the fatigue lifetime. Fracture morphology investigations were used by scanning electron microscope. The reliability analysis of the specimen was carried out by detail fatigue rating. The results revealed that the less the roughness is, the longer the fatigue life of open hole and the higher the value of DFR (Detail Fatigue Rating) is. Under the same technological conditions, the effect of corner crack on fatigue life of open holes is greater than the effect of internal crack. So, the effect of a decrease of roughness on the fatigue life of an open hole is similar to a change of crack type from a corner crack to an internal crack.

Effect of Nano CaO and MgO Addition on the Inclusions Composition in the Cast Microstructure of X80 Pipeline Steel

2013 ◽  
Vol 395-396 ◽  
pp. 289-292
Author(s):  
Yan Liu ◽  
Chun Lin He ◽  
Qian He Ma ◽  
Yang Liu
Keyword(s):  
Electron Microscope ◽  
Molten Steel ◽  
Pipeline Steel ◽  
Energy Dispersive Spectrometer ◽  
X80 Pipeline Steel ◽  
Composite Oxides ◽  
Segregation Phenomenon ◽  
Calcium And Magnesium ◽  
Scanning Electron ◽  
Cast Microstructure

Nanometer calcium and magnesium oxides were added into molten steel by the carrier method in the experiment. The experiment takes the X80 pipeline steel as the research object and analyses the effect of nanometer calcium and magnesium oxides addition on the inclusions in the cast microstructure of the X80 pipeline steel. The scanning electron microscope (SEM) and energy dispersive spectrometer (EDS) were used to analyze the composition of the inclusions in the cast microstructure of the X80 pipeline steel. The result reveals that when no addition of nanooxides, the inclusions in the cast microstructure are the C-Fe-Si-Al-Mn-based inclusions. When adding nanoMgO, the inclusions are mainly the composite oxides of Fe-Mg-Si-O, Fe-Mg-Si-Mn-O and Mg-Si-Mn-Al-O. When adding nanoCaO, the inclusions are mainly the composite oxides of Fe-Ca-Al-O, Fe-Ca-Si-O, Fe-Ca-Si-Mn-O and the composite oxides or sulfides of Fe-Ca-Si-Mn-O-S. There is more Fe in some inclusions and Fe is not uniformly dispersed in the molten steel. As the result, some certain segregation phenomenon takes place.

Sign in / Sign up

Export Citation Format

Share Document