scholarly journals The Influence of Gum Arabic Admixture on the Mechanical Properties of Lime-Metakaolin Paste Used as Binder in Hemp Concrete

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6775
Author(s):  
Przemysław Brzyski
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Mechanical Strength ◽  
Pore Diameter ◽  
Gum Arabic ◽  
Total Porosity ◽  
Hydrated Lime ◽  
Partial Replacement ◽  
Reference Formulation ◽  
Strength Parameters

Organic admixtures based on polysaccharides are used in construction for modifying the properties of mortars and concretes. Gum arabic is an example of a polysaccharide-based biopolymer. The aim of the article was to investigate the possibilities of improving the strength parameters of a binder paste based on hydrated lime and metakaolin. The paste was modified with powdered gum arabic at 1%, 3% and 5% (by mass) as a partial replacement for the binder mix. The influence of the admixture on the pore size distribution as well as flexural and compressive strength was investigated. The admixture enhanced the total porosity of the paste, increasing the pore diameter compared with the reference formulation. The increase in porosity, in turn, did not reduce the mechanical strength. Conversely, the admixture in the amount of 3% and 5% caused a significant increase in the flexural (by about 300% in relation to reference paste) and compressive strengths (by 25% and 60%, respectively). The tested pastes were used as a binder in a composite based on hemp shives. The influence of binder modification on the water absorption and compressive strength of hemp concrete was tested. The strength of the composite soaked in water was also tested. The modification of the binder with gum arabic in the amount of 3% and 5% increased the compressive strength of hemp concrete (not soaked in water) by 53% and 92%, respectively and reduced the mass absorptivity by 6.6% and 10.4%, respectively.

scholarly journals Material-removing machining wastes as a filler of a polymer concrete (industrial chips as a filler of a polymer concrete)

2021 ◽  
Vol 28 (1) ◽  
pp. 343-351
Author(s):  
Norbert Kępczak ◽  
Radosław Rosik ◽  
Mariusz Urbaniak
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Young’S Modulus ◽  
Industrial Waste ◽  
Splitting Tensile Strength ◽  
Polymer Concrete ◽  
Strength Parameters ◽  
Basic Parameters ◽  
Natural Fillers

Abstract The paper presents an impact of the addition of industrial machining chips on the mechanical properties of polymer concrete. As an additional filler, six types of industrial waste machining chips were used: steel fine chips, steel medium chips, steel thick chips, aluminium fine chips, aluminium medium chips, and titanium fine chips. During the research, the influence of the addition of chips on the basic parameters of mechanical properties, i.e., tensile strength, compressive strength, splitting tensile strength, and Young’s modulus, was analyzed. On the basis of the obtained results, conclusions were drawn that the addition of chips from machining causes a decrease in the value of the mechanical properties parameters of the polymer concrete even by 30%. The mechanism of cracking of samples, which were subjected to durability tests, was also explored. In addition, it was found that some chip waste can be used as a substitute for natural fillers during preparation of a mineral cast composition without losing much of the strength parameters.

scholarly journals Determination of Mechanical Properties of Altered Dacite by Laboratory Methods

Minerals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 813
Author(s):  
Veljko Rupar ◽  
Vladimir Čebašek ◽  
Vladimir Milisavljević ◽  
Dejan Stevanović ◽  
Nikola Živanović
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Rock Mass ◽  
Uniaxial Compressive Strength ◽  
Rock Material ◽  
Strength Parameter ◽  
Gradual Transition ◽  
Strength Parameters ◽  
Triaxial Compressive Strength ◽  
Heterogeneous Rock

This paper presents a methodology for determining the uniaxial and triaxial compressive strength of heterogeneous material composed of dacite (D) and altered dacite (AD). A zone of gradual transition from altered dacite to dacite was observed in the rock mass. The mechanical properties of the rock material in that zone were determined by laboratory tests of composite samples that consisted of rock material discs. However, the functional dependence on the strength parameter alteration of the rock material (UCS, intact UCS of the rock material, and mi) with an increase in the participation of “weaker” rock material was determined based on the test results of uniaxial and triaxial compressive strength. The participation of altered dacite directly affects the mode and mechanism of failure during testing. Uniaxial compressive strength (σciUCS) and intact uniaxial compressive strength (σciTX) decrease exponentially with increased AD volumetric participation. The critical ratio at which the uniaxial compressive strength of the composite sample equals the strength of the uniform AD sample was at a percentage of 30% AD. Comparison of the obtained exponential equation with practical suggestions shows a good correspondence. The suggested methodology for determining heterogeneous rock mass strength parameters allows us to determine the influence of rock material heterogeneity on the values σciUCS, σciTX, and constant mi. Obtained σciTX and constant mi dependences define more reliable rock material strength parameter values, which can be used, along with rock mass classification systems, as a basis for assessing rock mass parameters. Therefore, it is possible to predict the strength parameters of the heterogeneous rock mass at the transition of hard (D) and weak rock (AD) based on all calculated strength parameters for different participation of AD.

scholarly journals Mechanical Properties and Microstructural Features using Stone Dust as a Partial Replacement of Sand

2019 ◽  
Vol 8 (6) ◽  
pp. 5232-5237
Keyword(s):  
Mechanical Properties ◽  
Economic Growth ◽  
Sustainable Development ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Natural Resources ◽  
Strength Test ◽  
Partial Replacement ◽  
Test Results ◽  
Stone Dust

Today’s world is always leads to development in technology as well as the economic growth though sometime these will affect the environment badly. That’s why world environmental commission coined the termed called sustainable development where development takes place without hampering the others’ needs. Concrete industry is rapidly growing industry in India which consumes lots of natural resources during the production of concrete. Here Stone dust is used as a sustainable material in place of sand partially. M25 grade of concrete has been chosen for the experiments. Different mechanical properties of concrete like compressive strength, Split tensile, flexural strength etc. and Microstructural features like SEM, EDX have been included in this study. Compressive Strength and flexural strength test results shown the increase in the strength. Sulphate Resistance Properties have been tested by curing the cubes in the MgSO4 solution and increase in weight has been observed. Similarities are found in the SEM pictures

scholarly journals Influence of Restrained Condition on Mechanical Properties, Frost Resistance, and Carbonation Resistance of Expansive Concrete

Materials ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2136
Author(s):  
Nguyen Duc Van ◽  
Emika Kuroiwa ◽  
Jihoon Kim ◽  
Hyeonggil Choi ◽  
Yukio Hama
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Frost Resistance ◽  
Total Porosity ◽  
Length Change ◽  
Ratio Test ◽  
Expansive Concrete ◽  
Restrained Condition ◽  
Carbonation Resistance ◽  
Compressive Strength Test

This paper presents the results of an experimental investigation of the effect of the restrained condition on the mechanical properties, frost resistance, and carbonation resistance of expansive concrete with different water–binder ratios. In this study, length change ratio test, expansion strain test, compressive strength test, mercury intrusion porosimetry test, underwater weighing test, freezing–thawing test, and accelerated carbonation test were performed to evaluate the mechanical properties, pore size distribution, total porosity, and durability of expansive concrete under both restrained and unrestrained conditions. The test results indicate that the length change ratio and expansion strain of the expansive concrete were controlled by the restrained condition. The compressive strength of expansive concrete was enhanced by the triaxial restraining when the amount of expansive additive was 40 kg/m3 of concrete. Two hypotheses were described to explain the change of pore structure change expansive mortar. The results also indicate that the carbonation resistance and frost resistance were improved by the uniaxial restrained condition. Furthermore, the effect of the restrained condition must be considered to evaluate not only the experimental results of the expansive concrete with a high EX replacement level but also the expansive concrete combining other cement replacement materials.

The Influence of Pore-Strucrure on the Campressive Strength of Hardened Cement Paste

1984 ◽  
Vol 42 ◽  
Author(s):  
Huang Yiun-Yuan ◽  
Ding Wei ◽  
Lu Ping
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Pore Structure ◽  
Cement Paste ◽  
Total Porosity ◽  
Hardened Cement ◽  
Hardened Cement Paste ◽  
New Information ◽  
The Relationship ◽  
Empirical Constants

AbstractThe pore-structure strongly influences the carpressive strength of hardened cement paste (hcp) and other porous materials, as well as other mechanical properties. The simplest but most currently used expression representing the relationship between the pore-structure and compressive strength is fram Balshin: σ = σ0 (l-P)A, in which only the total porosity P is involved as a single parameter and σ0 and A are empirical constants. The influence of pore size distribution and pore shapes etc. are not considered.The authors introduce second parameter w - the factor of relative specific surface area of the pores other than the total porosity P into consideration and a new expression is proposed:σc=K11-p/1+2p(K2(1-p))K3w+K4 all the constants K1 - K4 can be determined experimentally. By using of this expression the new information relating the influence of pore-structure on the caopressive strength of hcp can be predicted.

Effect of steel slag powder, fly ash, and silica fume on the mechanical properties and durability of cement mortar

2019 ◽  
Vol 9 (9) ◽  
pp. 1049-1054
Author(s):  
Yunxia Lun ◽  
Fangfang Zheng
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Cement Mortar ◽  
Steel Slag ◽  
Mineral Admixtures ◽  
Partial Replacement ◽  
Slag Powder ◽  
Steel Slag Powder

This study is aimed at exploring the effect of steel slag powder (SSP), fly ash (FA), and silica fume (SF) on the mechanical properties and durability of cement mortar. SSP, SF, and FA were used as partial replacement of the Ordinary Portland cement (OPC). It was showed that the compressive and bending strength of steel slag powder were slightly lower than that of OPC. An increase in the SSP content caused a decrease in strength. However, the growth rate of compressive strength of SSP2 (20% replacement by the weight of OPC) at the curing ages of 90 days was about 8% higher than that of OPC, and the durability of SSP2 was better than that of OPC. The combination of mineral admixtures improved the later strength, water impermeability, and sulfate resistance compared with OPC and SSP2. The compressive strength of SSPFA (SSP and SF) at 90 days reached 70.3 MPa. The results of X-ray diffraction patterns and scanning electron microscopy indicated that SSP played a synergistic role with FA or SF to improve the performance of cement mortar.

Impact of Plasticizers on Technological Properties of Gypsum

2016 ◽  
Vol 865 ◽  
pp. 130-134 ◽  
Author(s):  
Dušan Dolák ◽  
Karel Dvořák
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Mechanical Strength ◽  
Research Work ◽  
High Strength ◽  
Building Industry ◽  
Technological Properties ◽  
Accurate Comparison

Sulphate binders based on gypsum are widely used in building industry. This research work was focused on testing the influence of Melflux plasticizers on the final properties of the gypsum mixture. The aim was to determine the correct concentration of the plasticizer considering workability and improvement of mechanical properties, especially the compressive strength. Different concentrations of plasticizers were tested in mixture of alfa and beta plaster. Each batch was created as paste of normal consistency to create accurate comparison. The results of experiment show significant improvements of mechanical strength of the hardened mixture while maintaining same consistency. This knowledge can be utilized in the design of high-strength sulphate binders.

scholarly journals Behavior of Steel Slag Concrete Subjected to Elevated Temperature

2020 ◽  
Vol 9 (4) ◽  
pp. 1165-1170
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
High Temperatures ◽  
Elevated Temperatures ◽  
Coarse Aggregate ◽  
Steel Slag ◽  
Partial Replacement ◽  
High Porosity ◽  
Residual Mechanical Properties

Recycling of materials has become a major interest for engineers. At present, the amount of slag deposited in storage yard adds up to millions of tons/year leading to the occupation of farm land and serious pollution to the environment, as a result of the rapid growth in the steel industry. Steel slag is made at 1500- 1650°C having a honey comp shape with high porosity. Using steel slag as the natural aggregate with a lower waste material cost can be considered as a good alternative for sustainable constructions. The objective of this study is to evaluate the performance of residual mechanical properties of concrete with steel slag as coarse aggregate partial replacement after exposing to high temperatures .This study investigates the behavior of using granulated slag as partial or fully coarse aggregate replacement with different percentages of 0%, 15%, 30%, 50% and 100% in concrete when subjected to elevated temperatures. Six groups of concrete mixes were prepared using various replacement percentages of slag exposed to different temperatures of 400 °C, 600 °C and 800 °C for different durations of 1hr, 1.5hr and 2hr. Evaluation tests were compressive strength, tensile strength, and bond strength. The steel slag concrete mixes showed week workability lower than control mix. A systematic increasing of almost up to 21.7% in compressive strength, and 66.2% in tensile strength with increasing the percentage of steel slag replacement to 50%. And the results showed improvement on concrete residual mechanical properties after subjected to elevated temperatures with the increase of steel slag content. The findings of this study give an overview of the effect of steel slag coarse aggregate replacement on concrete after exposed to high temperatures.

scholarly journals Mechanical and Microstructural Characterization of Quarry Rock Dust Incorporated Steel Fiber Reinforced Geopolymer Concrete and Residual Properties after Exposure to Elevated Temperatures

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6890
Author(s):  
Muhammad Ibraheem ◽  
Faheem Butt ◽  
Rana Muhammad Waqas ◽  
Khadim Hussain ◽  
Rana Faisal Tufail ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Weight Loss ◽  
Compressive Strength ◽  
Fly Ash ◽  
Mechanical Strength ◽  
Elevated Temperatures ◽  
Strength Properties ◽  
Steel Fibers ◽  
Geopolymer Concrete

The purpose of this research is to study the effects of quarry rock dust (QRD) and steel fibers (SF) inclusion on the fresh, mechanical, and microstructural properties of fly ash (FA) and ground granulated blast furnace slag (SG)-based geopolymer concrete (GPC) exposed to elevated temperatures. Such types of ternary mixes were prepared by blending waste materials from different industries, including QRD, SG, and FA, with alkaline activator solutions. The multiphysical models show that the inclusion of steel fibers and binders can enhance the mechanical properties of GPC. In this study, a total of 18 different mix proportions were designed with different proportions of QRD (0%, 5%, 10%, 15%, and 20%) and steel fibers (0.75% and 1.5%). The slag was replaced by different proportions of QRD in fly ash, and SG-based GPC mixes to study the effect of QRD incorporation. The mechanical properties of specimens, i.e., compressive strength, splitting tensile strength, and flexural strength, were determined by testing cubes, cylinders, and prisms, respectively, at different ages (7, 28, and 56 days). The specimens were also heated up to 800 °C to evaluate the resistance of specimens to elevated temperature in terms of residual compressive strength and weight loss. The test results showed that the mechanical strength of GPC mixes (without steel fibers) increased by 6–11%, with an increase in QRD content up to 15% at the age of 28 days. In contrast, more than 15% of QRD contents resulted in decreasing the mechanical strength properties. Incorporating steel fibers in a fraction of 0.75% by volume increased the compressive, tensile, and flexural strength of GPC mixes by 15%, 23%, and 34%, respectively. However, further addition of steel fibers at 1.5% by volume lowered the mechanical strength properties. The optimal mixture of QRD incorporated FA-SG-based GPC (QFS-GPC) was observed with 15% QRD and 0.75% steel fibers contents considering the performance in workability and mechanical properties. The results also showed that under elevated temperatures up to 800 °C, the weight loss of QFS-GPC specimens persistently increased with a consistent decrease in the residual compressive strength for increasing QRD content and temperature. Furthermore, the microstructure characterization of QRD blended GPC mixes were also carried out by performing scanning electron microscopy (SEM), X-ray diffraction (XRD), and energy dispersive spectroscopy (EDS).

scholarly journals Mechanical Properties of OPC - Geocement Concrete

2019 ◽  
Vol 8 (4) ◽  
pp. 3733-3736
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
External Heat ◽  
Partial Replacement ◽  
Strength Development ◽  
Strength Increase ◽  
Heat Curing ◽  
Compressive Strength Development

Nowadays geopolymer concretes are subjected to heat curing. A large amount of highly corrosive and the hygroscopic alkaline activators are nowadays generally utilized in producing geopolymer concretes. In this paper, hybrid Ordinary Portland Cement (OPC) and geopolymer mixes are developed. The mainly used activator id the Solid potassium carbonate at different percentage is used as 5% & 10% of the weight of geopolymeric materials and OPC was blended with geopolymeric materials in different proportions. By adding cement, improves all the geopolymer properties except workability. By Applying external heat, it plays an important role in gaining strength. Strength gained by the absence of external heat is achieved by using Portland cement as a partial replacement of geocement. The influence of OPC content on the compressive strength development is investigated, and the optimized amount of solid activator to be used in the mix is also investigated. It is observed that percentage of strength increase decreases from52.24% to 14.77% as the OPC content increased from 20% to 60%.

Sign in / Sign up

Export Citation Format

Share Document