scholarly journals Thermal Decomposition and Kinetics of Pentlandite-Bearing Ore Oxidation in the Air Atmosphere

Metals ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 1364
Author(s):  
Kristina Božinović ◽  
Nada Štrbac ◽  
Aleksandra Mitovski ◽  
Miroslav Sokić ◽  
Duško Minić ◽  
...  

The roasting of sulfide ores and concentrates is one of the most important steps in pyrometallurgical metal production from primary raw materials, due to the necessity of excess sulfur removal, present in the virgin material. Pentlandite is one of the main sources for nickel pyrometallurgical production. The knowledge of its reaction mechanism, products distribution during oxidation and reaction kinetics is important for optimizing the production process. Raw pentlandite-bearing ore from the Levack mine (Ontario, Canada) was subjected to oxidative roasting in the air atmosphere. A chemical analysis of the initial sample was conducted according to EDXRF (Energy-Dispersive X-Ray Fluorescence) and AAS (Atomic Adsorption Spectrometry) results. The characterization of the initial sample and oxidation products was conducted by an XRD (X-ray Diffraction) and SEM/EDS (Scanning Electron Microscopy with Energy Dispersive Spectrometry) analysis. Thermodynamic calculations, a phase analysis and construction of Kellogg diagrams for Ni-S-O and Fe-S-O systems at 298 K, 773 K, 923 K and 1073 K were used for proposing the theoretical reaction mechanism. A thermal analysis (TG/DTA—Thermogravimetric and Differential Thermal Analyses) was conducted in temperature range 298–1273 K, under a heating rate of 15° min−1. A kinetic analysis was conducted according to the non-isothermal method of Daniels and Borchardt, under a heating rate of 15° min−1. Calculated activation energies of 113 kJ mol−1, 146 kJ mol−1 and 356 kJ mol−1 for three oxidation stages imply that in every examined stage of the oxidation process, temperature is a dominant factor determining the reaction rate.

10.30544/320 ◽  
2017 ◽  
Vol 23 (3) ◽  
pp. 267-280 ◽  
Author(s):  
Aleksandra Mitovski ◽  
Nada Štrbac ◽  
Miroslav Sokić ◽  
Milan Kragović ◽  
Vesna Grekulović

Sulfide copper concentrate from domestic ore deposit (Bor, Serbia) was subjected to oxidation in the air atmosphere due to a better understanding of reaction mechanism and oxidation of various sulfides present in the copper concentrate at elevated temperatures. Results of the initial sample characterization showed that concentrate is chalcopyrite–enargite-tennantite type, with an increased arsenic content. Characterization of the oxidation products showed the presence of sulfates, oxysulfates, and oxides. Based on predominance area diagrams for Me-S-O systems (Me = Cu, Fe, As) combined with thermal analysis results, the reaction mechanism of the oxidation process was proposed. The reactions which occur in the temperature range 25 – 1000 °C indicate that sulfides are unstable in the oxidative conditions. Sulfides from the initial sample decomposed into binary copper and iron sulfides and volatile arsenic oxides at lower temperatures. Further heating led to oxidation of sulfides into iron oxides and copper sulfates and oxysulfates. At higher temperatures sulfates and oxysulfates decomposed into oxides. Kinetic analysis of the oxidation process was done using Ozawa’s method in the non-isothermal conditions. The values for activation energies showed that the reactions are chemically controlled and the temperature is the most influential parameter on the reaction rates.


2011 ◽  
Vol 236-238 ◽  
pp. 1919-1922 ◽  
Author(s):  
Wen Jun Fa ◽  
Pin Jiang Li ◽  
Yan Ge Zhang ◽  
Li Li Guo ◽  
Jia Fan Guo ◽  
...  

BiOI nanolamellas and BiSI nanowires were synthesized using Bi(NO3)3·5H2O, (NH2)2CS and I2 as reactants in the solvothermal process with ethanol as the system media. The as-prepared samples were characterized by X-ray powder diffraction (XRD), scanning electronic microscopy (SEM), Energy-Dispersive X-ray Spectrometer (EDS). The competitive growth of BiOI and BiSI were investigated by changing the quantity of (NH2)2CS. A possible reaction mechanism was proposed.


Materials ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 2209 ◽  
Author(s):  
Jing Liu ◽  
Xiao-Min Li ◽  
Jing He ◽  
Lu-Ying Wang ◽  
Jian-Du Lei

A core-shell Cu-benzene-1,3,5-tricarboxylic acid (Cu-BTC)@TiO2 was successfully synthesized for photocatalysis-assisted adsorptive desulfurization to improve adsorptive desulfurization (ADS) performance. Under ultraviolet (UV) light irradiation, the TiO2 shell on the surface of Cu-BTC achieved photocatalytic oxidation of thiophenic S-compounds, and the Cu-BTC core adsorbed the oxidation products (sulfoxides and sulfones). The photocatalyst and adsorbent were combined using a distinct core-shell structure. The morphology and structure of the fabricated Cu-BTC@TiO2 microspheres were verified by scanning electron microscopy, high-resolution transmission electron microscopy, energy-dispersive x-ray spectroscopy, X-ray powder diffraction, nitrogen adsorption-desorption and X-ray photoelectron spectroscopy analyses. A potential formation mechanism of Cu-BTC@TiO2 is proposed based on complementary experiments. The sulfur removal efficiency of the microspheres was evaluated by selective adsorption of benzothiophene (BT) and dibenzothiophene (DBT) from a model fuel with a sulfur concentration of 1000 ppmw. Within a reaction time of 20 min, the BT and DBT conversion reached 86% and 95%, respectively, and achieved ADS capacities of 63.76 and 59.39 mg/g, respectively. The BT conversion and DBT conversion obtained using Cu-BTC@TiO2 was 6.5 and 4.6 times higher, respectively, than that obtained using Cu-BTC. A desulfurization mechanism was proposed, the interaction between thiophenic sulfur compounds and Cu-BTC@TiO2 microspheres was discussed, and the kinetic behavior was analyzed.


2021 ◽  
Vol 2080 (1) ◽  
pp. 012009
Author(s):  
Siti Fatimah Azzahran Abdullah ◽  
Siti Shuhadah Md Saleh ◽  
Nur Farahiyah Mohammad ◽  
Mohd Sobri Idris ◽  
H. R. Saliu

Abstract Dolomite is a mineral material that is formed from limestone which is mostly contains the calcite (CaCO3) and magnesite (MgCO3). This paper aimed to study on thermal decomposition of dolomite under air atmosphere. Calcination of dolomite was carried out by using furnace with heating rate of 10 °C/minute in an air atmosphere. The different temperature of calcination was varied at 400 °C, 600 °C, 800 °C, and 1000 °C within 6 hours. Phase analysis (XRD) and functional group analysis (FTIR) were carried out to analysis the dolomite after calcination. Microstructural (SEM) and Energy Dispersive X-ray (EDX) analysis showed that the main constituents of pure dolomite include CaCO3 (calcite), MgCO3 (magnesite), CaO, and MgO. From the results, XRD showed that the high intensity of CaO and MgO at 800 - 1000 °C was much stronger than that of dolomite at 400 - 600 °C. In addition, FTIR presents strong and intense bands are observed at 3632.23 and 3690.98 cm−1 (800 °C), and also 3694.03 and 3633.60 cm−1 (1000 °C) due to the calcium oxide.


Author(s):  
J.M. Titchmarsh

The advances in recent years in the microanalytical capabilities of conventional TEM's fitted with probe forming lenses allow much more detailed investigations to be made of the microstructures of complex alloys, such as ferritic steels, than have been possible previously. In particular, the identification of individual precipitate particles with dimensions of a few tens of nanometers in alloys containing high densities of several chemically and crystallographically different precipitate types is feasible. The aim of the investigation described in this paper was to establish a method which allowed individual particle identification to be made in a few seconds so that large numbers of particles could be examined in a few hours.A Philips EM400 microscope, fitted with the scanning transmission (STEM) objective lens pole-pieces and an EDAX energy dispersive X-ray analyser, was used at 120 kV with a thermal W hairpin filament. The precipitates examined were extracted using a standard C replica technique from specimens of a 2¼Cr-lMo ferritic steel in a quenched and tempered condition.


Author(s):  
J. Bentley ◽  
E. A. Kenik

Instruments combining a 100 kV transmission electron microscope (TEM) with scanning transmission (STEM), secondary electron (SEM) and x-ray energy dispersive spectrometer (EDS) attachments to give analytical capabilities are becoming increasingly available and useful. Some typical applications in the field of materials science which make use of the small probe size and thin specimen geometry are the chemical analysis of small precipitates contained within a thin foil and the measurement of chemical concentration profiles near microstructural features such as grain boundaries, point defect clusters, dislocations, or precipitates. Quantitative x-ray analysis of bulk samples using EDS on a conventional SEM is reasonably well established, but much less work has been performed on thin metal foils using the higher accelerating voltages available in TEM based instruments.


Author(s):  
Allen Angel ◽  
Kathryn A. Jakes

Fabrics recovered from archaeological sites often are so badly degraded that fiber identification based on physical morphology is difficult. Although diagenetic changes may be viewed as destructive to factors necessary for the discernment of fiber information, changes occurring during any stage of a fiber's lifetime leave a record within the fiber's chemical and physical structure. These alterations may offer valuable clues to understanding the conditions of the fiber's growth, fiber preparation and fabric processing technology and conditions of burial or long term storage (1).Energy dispersive spectrometry has been reported to be suitable for determination of mordant treatment on historic fibers (2,3) and has been used to characterize metal wrapping of combination yarns (4,5). In this study, a technique is developed which provides fractured cross sections of fibers for x-ray analysis and elemental mapping. In addition, backscattered electron imaging (BSI) and energy dispersive x-ray microanalysis (EDS) are utilized to correlate elements to their distribution in fibers.


Author(s):  
Marc H. Peeters ◽  
Max T. Otten

Over the past decades, the combination of energy-dispersive analysis of X-rays and scanning electron microscopy has proved to be a powerful tool for fast and reliable elemental characterization of a large variety of specimens. The technique has evolved rapidly from a purely qualitative characterization method to a reliable quantitative way of analysis. In the last 5 years, an increasing need for automation is observed, whereby energy-dispersive analysers control the beam and stage movement of the scanning electron microscope in order to collect digital X-ray images and perform unattended point analysis over multiple locations.The Philips High-speed Analysis of X-rays system (PHAX-Scan) makes use of the high performance dual-processor structure of the EDAX PV9900 analyser and the databus structure of the Philips series 500 scanning electron microscope to provide a highly automated, user-friendly and extremely fast microanalysis system. The software that runs on the hardware described above was specifically designed to provide the ultimate attainable speed on the system.


Author(s):  
Michael E. Rock ◽  
Vern Kennedy ◽  
Bhaskar Deodhar ◽  
Thomas G. Stoebe

Cellophane is a composite polymer material, made up of regenerated cellulose (usually derived from wood pulp) which has been chemically transformed into "viscose", then formed into a (1 mil thickness) transparent sheet through an extrusion process. Although primarily produced for the food industry, cellophane's use as a separator material in the silver-zinc secondary battery system has proved to be another important market. We examined 14 samples from five producers of cellophane, which are being evaluated as the separator material for a silver/zinc alkaline battery system in an autonomous underwater target vehicle. Our intent was to identify structural and/or chemical differences between samples which could be related to the functional differences seen in the lifetimes of these various battery separators. The unused cellophane samples were examined by transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDS). Cellophane samples were cross sectioned (125-150 nm) using a diamond knife on a RMC MT-6000 ultramicrotome. Sections were examined in a Philips 430-T TEM at 200 kV. Analysis included morphological characterization, and EDS (for chemical composition). EDS was performed using an EDAX windowless detector.


Author(s):  
Y. Sato ◽  
T. Hashimoto ◽  
M. Ichihashi ◽  
Y. Ueki ◽  
K. Hirose ◽  
...  

Analytical TEMs have two variations in x-ray detector geometry, high and low angle take off. The high take off angle is advantageous for accuracy of quantitative analysis, because the x rays are less absorbed when they go through the sample. The low take off angle geometry enables better sensitivity because of larger detector solid angle.Hitachi HF-2000 cold field emission TEM has two versions; high angle take off and low angle take off. The former allows an energy dispersive x-ray detector above the objective lens. The latter allows the detector beside the objective lens. The x-ray take off angle is 68° for the high take off angle with the specimen held at right angles to the beam, and 22° for the low angle take off. The solid angle is 0.037 sr for the high angle take off, and 0.12 sr for the low angle take off, using a 30 mm2 detector.


Sign in / Sign up

Export Citation Format

Share Document