scholarly journals Laboratory Evaluation of the Residue of Rubber-Modified Emulsified Asphalt

2020 ◽  
Vol 12 (20) ◽  
pp. 8383
Author(s):  
Dongdong Ge ◽  
Xiaodong Zhou ◽  
Siyu Chen ◽  
Dongzhao Jin ◽  
Zhanping You
Keyword(s):  
Chemical Change ◽  
Asphalt Binder ◽  
High Volume ◽  
Crumb Rubber ◽  
Asphalt Binders ◽  
Laboratory Evaluation ◽  
Chip Seal ◽  
Improvement Effect ◽  
Pavement Construction ◽  
Emulsified Asphalt

Emulsified asphalt has been widely used in various surface treatment methods such as chip seal for low-volume road preservation. Using modified emulsified asphalt made it possible to use chip seal technology on medium- and even high-volume traffic pavements. The main objective of the study is to quantify the residue characteristics of rubber-modified emulsified asphalt and to assess the effectiveness of using crumb rubber to modify emulsified asphalt binder. The four emulsified asphalt residues used the distillation procedure. Then, the rheology characteristics of emulsified asphalt residue were evaluated. The Fourier transform infrared spectroscopy (FTIR) test analyzed the chemical change of emulsified asphalt during the aging procedure. The results indicate that the evaporation method cannot remove all the water in emulsified asphalt. The mass change during the rolling thin film oven (RTFO) process only represented the component change of emulsified asphalt binder residue. Both the high-temperature and low-temperature performance grade of the two emulsified asphalt binders with rubber were lower. The original asphalt binder adopted to emulsification had a crucial influence on the performance of emulsified asphalt. The rubber modification enhanced the property of the emulsified asphalt binder at low temperatures, and the improvement effect was enhanced as the rubber content in the emulsified asphalt was raised. The C=O band was more effective in quantifying the aging condition of the residue. The findings of this study may further advance the emulsified asphalt technology in pavement construction and maintenance.

scholarly journals Material Properties and Environmental Benefits of Hot-Mix Asphalt Mixes Including Local Crumb Rubber Obtained from Scrap Tires

Environments ◽  
2021 ◽  
Vol 8 (6) ◽  
pp. 47
Author(s):  
Lim Min Khiong ◽  
Md. Safiuddin ◽  
Mohammad Abdul Mannan ◽  
Resdiansyah
Keyword(s):  
Asphalt Binder ◽  
Crumb Rubber ◽  
Environmental Benefits ◽  
Asphalt Binders ◽  
Rubber Content ◽  
Scrap Tires ◽  
Asphalt Mixes ◽  
Temperature Resistance ◽  
Modified Asphalt ◽  
Marshall Stability

This paper presents the results of a laboratory-based experimental investigation on the properties of asphalt binder and hot-mix asphalt (HMA) mixes modified by locally available crumb rubber, which was used as a partial replacement of asphalt by weight. In this study, fine crumb rubber with a particle size in the range of 0.3–0.6 mm, obtained from scrap tires, was added to the asphalt binder through the wet process. Crumb rubber contents of 5%, 10%, 15%, and 19% by weight of asphalt were added to the virgin binder in order to prepare the modified asphalt binder samples, while the unmodified asphalt binder was used as the control sample. The crumb rubber modified binder samples were examined for measuring viscosity indirectly using the penetration test, and temperature resistance using the softening point test. Later, both the modified and unmodified asphalt binders were used to produce HMA mixes. Two categories of HMA mix commonly used in Malaysia—namely, AC 14 (dense-graded) and SMA 14 (gap-graded)—were produced using the modified asphalt binders containing 5%, 10%, 15%, and 19% crumb rubber. Two AC 14 and SMA 14 control mixes were also produced, incorporating the unmodified asphalt binder (0% crumb rubber). All of the AC 14 and SMA 14 asphalt mixes were examined in order to determine their volumetric properties, such as bulk density, voids in total mix (VTM), voids in mineral aggregate (VMA), and voids filled with asphalt (VFA). In addition, the Marshall stability, Marshall flow, and stiffness of all of the AC 14 and SMA 14 mixes were determined. Test results indicated that the modified asphalt binders possessed higher viscosity and temperature resistance than the unmodified asphalt binder. The viscosity and temperature resistance of the asphalt binders increased with the increase in their crumb rubber content. The increased crumb rubber content also led to improvements in the volumetric properties (bulk density, VTM, VMA, and VFA) of the AC 14 and SMA 14 mixes. In addition, the performance characteristics of the AC 14 and SMA 14 mixes—such as Marshall stability, Marshall flow, and stiffness—increased with the increase in crumb rubber content. However, the AC 14 mixes performed much better than the SMA 14 mixes. The overall research findings suggest that crumb rubber can be used to produce durable and sustainable HMA mixes, with manifold environmental benefits, for use in flexible pavements carrying the heavy traffic load of highways.

Evaluation of Adhesion Properties of Modified Asphalt Binders with Use of Binder Bond Strength Test

2017 ◽  
Vol 2632 (1) ◽  
pp. 88-98 ◽  
Author(s):  
Weidong Huang ◽  
Lu Zhou
Keyword(s):  
Bond Strength ◽  
Asphalt Binder ◽  
Gel Permeation Chromatography ◽  
Crumb Rubber ◽  
Asphalt Binders ◽  
Adhesion Properties ◽  
Rubber Powder ◽  
Positive Effects ◽  
Tracking Device ◽  
Styrene Butadiene

Moisture damage is a prominent problem of asphalt pavements. The bond strength between asphalt and aggregates is a crucial factor that influences the capability of asphalt to resist moisture-induced damage. In this study, a binder bond strength (BBS) test was conducted to evaluate the effects of various modifiers and additives of different amounts on bond strength between asphalt and aggregates. Furthermore, the influence of styrene–butadiene–styrene (SBS) on adhesion behavior of asphalt binder was investigated through a gel permeation chromatography (GPC) test. Finally, the results of the BBS test were compared with the findings obtained from a Hamburg wheel-tracking device (HWTD) test, which reflected the moisture sensitivity of mixtures under wet conditions. Results indicated that gilsonite, high-density polyethylene, and polyphosphoric acid improved the bond strength of the base asphalt; SBS had no positive effects on asphalt adhesion properties; and SBS at a low amount reduced the bond strength. Ethylene bis-stearamide wax, crumb rubber, terminal blend (TB) rubber powder, and compound modifier TB rubber powder plus SBS decreased the bond strength. The GPC test results showed that SBS possibly did not actively contribute to the formation of bond strength between asphalt and aggregates. Test data for BBS and HWTD tests under wet conditions confirmed that there was no discernible correlation between these two tests when adhesion properties of modified asphalts were evaluated. However, the results of the BBS test were in accordance with those of the HWTD test when the adhesion of asphalt with different amounts of the same modifier and the mixture resistance to water damage were evaluated.

scholarly journals Balancing the Performance and Environmental Concerns of Used Motor Oil as Rejuvenator in Asphalt Mixes

Recycling ◽  
2019 ◽  
Vol 4 (1) ◽  
pp. 11 ◽  
Author(s):  
Eslam Deef-Allah ◽  
Magdy Abdelrahman ◽  
Mark Fitch ◽  
Mohyeldin Ragab ◽  
Mousumi Bose ◽  
...  
Keyword(s):  
Environmental Protection Agency ◽  
Asphalt Binder ◽  
Crumb Rubber ◽  
Asphalt Binders ◽  
Environmental Concerns ◽  
Ethyl Benzene ◽  
Motor Oil ◽  
Asphalt Mixes ◽  
Used Motor Oil ◽  
The Us

Road deterioration inspires researchers to enhance the properties of asphalt binder for better performing mixes. Recycled tire rubber, or crumb rubber modifier (CRM), and used motor oil (UMO) are two modifiers that enhance asphalt binder performance through two different mechanisms. CRM affects high-temperature properties while UMO modifies low-temperature properties. Potential environmental concerns arising from the use of UMO have been raised in the literature. In this paper, the two recycled materials were investigated for their ability to complement each other. Both performance benefits of using both materials and the environmental concerns of using UMO were studied. Four CRM asphalt binders were investigated: two with UMO and two without UMO. Environmental impacts were evaluated using gas chromatography to check air emissions for benzene, toluene, ethyl-benzene, and xylenes (BTEX). The potential for toxic leaching of elements from modified hot mix asphalt (HMA) were checked using the US Environmental Protection Agency (EPA) Toxicity Characteristic Leaching Protocol (TCLP). For asphalt binders modified by CRM-UMO combinations, CRM decreased the amounts of released BTEX components, presumably by absorbing UMO and slowing the release of BTEX. Leaching results concluded that UMO mixtures showed a notable percentage of sulfur (S) as compared to non-UMO mixes. All these leachate components were under EPA limits.

scholarly journals Laboratory Evaluation of Asphalt Binder Modified with Crumb Rubber and Basalt Fiber

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Li Liu ◽  
You Huang ◽  
Zhaohui Liu
Keyword(s):  
Shear Strength ◽  
Low Temperature ◽  
Complex Modulus ◽  
Heavy Traffic ◽  
Asphalt Binder ◽  
Basalt Fiber ◽  
Crumb Rubber ◽  
Traffic Load ◽  
Laboratory Evaluation ◽  
Temperature Property

Asphalt pavement subjected to heavy traffic load and harsh environmental conditions can easily build up damage and shorten the service life. In this paper, different dosages of basalt fiber (BF) were introduced into crumb rubber (CR) modified asphalt binder, and a series of laboratory tests were carried out to evaluate the properties and performances. A dynamic shear rheometer (DSR) was employed to evaluate viscosity and rheological properties. Bending beam rheometer (BBR) test and direct tensile test (DTT) were conducted to test the low temperature property. Cone penetration was designed to test shear strength. Results show that the optimum content of BF is 0.3% by the weight of asphalt binder based on the overall performance evaluation. Viscosity, complex modulus, fatigue property, rutting resistance, and shear strength are improved by introducing BF into asphalt binder. Stiffness and elasticity are also increased. BBR indicates that ductility at low temperature is reduced a little by the presence of BF, but DTT shows that both tensile strength and elongation are improved by BF. Considering that DTT is more performance related, DTT is preferred over BBR to evaluate cracking potentials at low temperatures of asphalt binder modified with CR and BF. Finally, it is revealed through microscale scanning that three mechanisms, absorption of asphalt binder, 3-dimensional fiber network, and bridging effects, contribute to the performance improvement of asphalt binder modified with CR and BF.

scholarly journals Experimental Study to Determine the Most Preferred Additive for Improving Asphalt Performance Using Polypropylene, Crumb Rubber, and Tafpack Super in Medium and High-Temperature Range

2019 ◽  
Vol 9 (8) ◽  
pp. 1567 ◽  
Author(s):  
Huang Xiaoming ◽  
Ismail Bakheit Eldouma
Keyword(s):  
High Temperature ◽  
Physical Properties ◽  
Mechanical Performance ◽  
Asphalt Binder ◽  
Crumb Rubber ◽  
Asphalt Binders ◽  
Modified Bitumen ◽  
Asphalt Modification ◽  
Rotational Viscosity ◽  
Asphalt Performance

The overall objectives of this study were to determine the most appropriate additive for improving the physical properties and the medium- and high-temperature performances (mechanical performance) of asphalt binders. Three different types of modified binders were prepared: crumb rubber modifier (CRM), polypropylene (PP), and tafpack super (TPS), which had concentrations of 2%, 3%, 3.5%, and 4% by weight of asphalt binder, for each modifier. Their physical and rheological properties were evaluated by applying various tests such as ductility, rotational viscosity, toughness, and tenacity, as well as the dynamic shear rheometer (DSR) test. As a result, the physical properties of the modified bitumen binders were compared, as were the medium- and high-temperature performances (mechanical performance), which had temperatures of 58, 64, 70, 76, 82, and 88 °C, respectively. This was how the most appropriate modifier was determined. The results demonstrated that the asphalt binder properties significantly improved by utilizing CRM followed by PP and TPS modifiers. The increase in the rutting parameter (G*/sin(δ)) after asphalt modification indicated its excellent performance at both medium- and high-temperatures. Lastly, the CRM was determined as the most preferred additive because of its positive effect on the physical properties and enhancement of the medium- and high-temperature performance (mechanical performance).

scholarly journals Performance Evaluation of Crumb Rubber Asphalt Modified with Silicone-Based Warm Mix Additives

2020 ◽  
Vol 2020 ◽  
pp. 1-17 ◽  
Author(s):  
Nonde Lushinga ◽  
Liping Cao ◽  
Zejiao Dong ◽  
Chen Yang ◽  
Cyriaque O. Assogba
Keyword(s):  
Asphalt Binder ◽  
Fatigue Cracking ◽  
Crumb Rubber ◽  
Warm Mix Asphalt ◽  
Asphalt Binders ◽  
Water Repellent ◽  
Creep Recovery ◽  
Viscoelastic Continuum Damage ◽  
Warm Mix Additives ◽  
Different Temperatures

This research was conducted to elucidate better understanding of the performance of crumb rubber asphalt modified with silicone-based warm mix additives. Two different silicone-based warm mix asphalt (WMA) additives (herein Tego XP and Addibit) were used to prepare crumb rubber modified (CRM) warm mix asphalt binders. The viscosity of these CRM binders was measured at different temperatures and shearing rates. Furthermore, softening point and penetration tests, Multiple Stress Creep Recovery (MSCR), Time Sweep (TS), Atomic Force Microscopy (AFM), Frequency sweep (FS), and Fourier Transform Infrared (FTIR) tests were also conducted on prepared samples. Based on these robust and rigorous laboratory experiments, it was established that viscosity of CRM binders was reduced by addition of Tego XP and Addibit WMA additives. However, WMA additives had different influence on rheological properties of the binder. CRM binder with Tego XP improved resistance to rutting of the binders but would degrade the fatigue performance. On the contrary, viscoelastic continuum damage (VECD) model results and those of phase angle approach revealed that the binder with Addibit improved resistance to fatigue cracking of the binders but had no adverse effects on high temperature rutting performance. FTIR test results established a presence of polydimethylsiloxane (PDMS) in CRM binders with Tego XP and Addibit. PDMS is a well-known hydrophobic organic and inorganic polymer that is water repellent; therefore, binders containing these silicone-based warm mix additives could be beneficial in resisting moisture damage in asphalt binders and mixtures. Morphology of CRM binders with and without WMA revealed good distribution of the rubber particles in asphalt binder matrix. Further addition of WMA increased surface roughness of the binder, which can be correlated to changes in microstructure properties of the binder. Therefore, the study concluded that addition of Tego XP and Addibit reduces viscosity and improves mechanical properties of the asphalt binder.

Evaluation of Local Asphalt Binders under Superpave Specification

2012 ◽  
Vol 178-181 ◽  
pp. 1509-1512 ◽  
Author(s):  
Hussain Arshad ◽  
Yan Jun Qiu
Keyword(s):  
High Temperatures ◽  
Flexible Pavements ◽  
Asphalt Binder ◽  
Flexible Pavement ◽  
Asphalt Binders ◽  
Grading System ◽  
Empirical Tests ◽  
Heavy Loads ◽  
Pavement Construction

Premature rutting due to high temperatures and heavy loads has been a major distress on flexible pavements in Pakistan. One of the main causes of this early rutting is the available asphalt binders, which are still graded by using penetration grading system. The penetration grading system is based on empirical tests and does not link with performance. To improve the quality of the flexible pavement and to avoid the premature rutting the performance based testings were conducting in laboratory. This study evaluated performance graded (PG) binders for use in pavement construction in the country. Five different penetration graded asphalt binder, typically available in the country were graded according to PG system. The performance grades (PG) for all binders were determined based on DSR and BBR results. The two same penetration grades ARL60/70 and NRL 60/70 have different PG grades. The two different penetration grades ARL60/70 and NRL 80/100 have same PG grade. The results show that the local binders are very soft due to which they performed poorly at high temperatures and prone to severe rutting.

scholarly journals Influence of Different Types of Emulsifiers on Properties of Emulsified Asphalt Binder and Its Evaporation Residue by Molecular Dynamics Simulation

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Ying-feng Wu ◽  
Xin Qu
Keyword(s):  
Mechanical Properties ◽  
Asphalt Binder ◽  
Evaporation Residue ◽  
Dynamics Simulation ◽  
Asphalt Binders ◽  
Adhesion Behavior ◽  
Effective Role ◽  
Dodecyl Benzene Sulfonate ◽  
Emulsified Asphalt ◽  
Evaporation Residues

There is an important role in the properties of emulsified asphalt binder and its evaporation residue about emulsifier, which has been confirmed by experiment and chemical tests. However, there is little research about the emulsifier at microperspective. Therefore, the influence of two kinds of emulsifiers, a typical cationic emulsifier (dodecyl benzene sulfonate) and a typical anionic emulsifier (dodecyl primary amine), on technical properties of emulsified asphalt binder and its evaporation residues such as store stability, workability, breaking behavior, and mechanical properties are investigated using a microapproach. Results show that there is an effective role in the storage stability, workability, and demulsification of emulsified asphalt binder about cationic emulsifier compared with anionic emulsifier. The anionic emulsifier makes the density of evaporation residue larger. However, the mechanical properties of anionic emulsified asphalt evaporation residue are conversely smaller compared with the cationic emulsified asphalt evaporation residue. The adhesion behavior results have confirmed that the anionic emulsified asphalt evaporation residue has a negative adhesion with aggregate due to its anion. The mechanism of the different emulsifiers on asphalt binders and their evaporation residue is explored at a microscale to help us to understand emulsified asphalt binder and its evaporation residue more in depth.

scholarly journals Laboratory Evaluation of Sustainable PMA Binder Containing Styrene-Isoprene-Styrene (SIS) and Thermoplastic Polyurethane

2020 ◽  
Vol 12 (23) ◽  
pp. 10057
Author(s):  
Hyun Hwan Kim ◽  
Mithil Mazumder ◽  
Soon-Jae Lee ◽  
Moon-Sup Lee
Keyword(s):  
Thermoplastic Polyurethane ◽  
Asphalt Binder ◽  
Asphalt Binders ◽  
Laboratory Evaluation ◽  
Creep Recovery ◽  
Before And After ◽  
Multiple Stress Creep Recovery ◽  
Compaction Processes ◽  
Positive Effect

In this study, thermoplastic polyurethane (TPU) and styrene-isoprene-styrene (SIS) were utilized to enhance asphalt binder properties. Superpave asphalt binder tests and multiple stress creep recovery (MSCR) were conducted to evaluate the physical and rheological performance (viscosity, rutting, and cracking properties) of the asphalt binders before and after short-term aging and after the long-term aging process. The results showed that (i) TPU has a positive effect on workability, including the mixing and compaction processes, which was evident from the reduced binder viscosity; (ii) asphalt binders with TPU and SIS showed better rutting resistance compared to the SIS binders without TPU; (iii) the cracking resistance of asphalt binders was found to be improved significantly with the addition of TPU; and (iv) TPU has the potential to be considered as a sustainable polymer modifier for producing bearable asphalt binders by improving rutting and crack resistance without increasing the melting temperature of the asphalt binders.

Sign in / Sign up

Export Citation Format

Share Document