Study on the Dry-Cleaning Process of Mink Fur Based on Subcritical Solvent

2021 ◽  
Vol 116 (9) ◽  
Author(s):  
Yingxuan Wang ◽  
Qiao Xia ◽  
Qiang Liu ◽  
Hong Dai ◽  
Zongcai Zhang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Oil Content ◽  
Wool Fiber ◽  
Environmentally Benign ◽  
Cleaning Process ◽  
Dry Cleaning ◽  
Shrinkage Temperature ◽  
Dispersion Degree

It is significant to apply environmentally benign technology to fur processing. In this paper, subcritical extraction with n-pentane was used to dry clean mink fur and the effect on the quality of mink fur was studied. The dispersion degree of the leather fibers and the morphology of the wool fiber were characterized with SEM, the mechanical properties, shrinkage temperature and oil content left in fur were determined and analyzed. The results showed that the fibers of mink fur were well separated and no excess lipids in the fibers or on the surface of mink fur and the hair of the mink fur is not damaged. The tensile strength and elongation of mink fur show slight increase respectively, and the shrinkage temperature of mink fur that was treated by subcritical solvent was significantly increased compared with that of the mink fur treated with tetrachloroethylene by conventional dry cleaning method.

scholarly journals The Influence of Different Plasma Cell Discharges on the Performance Quality of Surgical Gown Samples

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4329
Author(s):  
Atif H. Asghar ◽  
Ahmed Rida Galaly
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Exposure Time ◽  
Electrical Characteristics ◽  
Cathode Fall ◽  
Treatment Efficiency ◽  
Performance Quality ◽  
Surgical Gown ◽  
The One

An experimental study was performed on a low-density plasma discharge using two different configurations of the plasma cell cathode, namely, the one mesh system electrodes (OMSE) and the one mesh and three system electrodes (OMTSE), to determine the electrical characteristics of the plasma such as current–voltage characteristics, breakdown voltage (VB), Paschen curves, current density (J), cathode fall thickness (dc), and electron density of the treated sample. The influence of the electrical characteristics of the plasma fluid in the cathode fall region for different cathode configuration cells (OMSE and OMTSE) on the performance quality of a surgical gown was studied to determine surface modification, treatment efficiency, exposure time, wettability property, and mechanical properties. Over a very short exposure time, the treatment efficiency for the surgical gown surface of plasma over the mesh cathode at a distance equivalent to the cathode fall distance dc values of the OMTSE and for OMSE reached a maximum. The wettability property decreased from 90 to 40% for OMTSE over a 180 s exposure time and decreased from 90 to 10% for OMSE over a 160 s exposure time. The mechanisms of each stage of surgical gown treatment by plasma are described. In this study, the mechanical properties of the untreated and treated surgical gown samples such as the tensile strength and elongation percentage, ultimate tensile strength, yield strength, strain hardening, resilience, toughness, and fracture (breaking) point were studied. Plasma had a more positive effect on the mechanical properties of the OMSE reactor than those of the OMTSE reactor.

The Effect of Yarn Linear Density on Mechanical Properties of Plain Woven Kenaf Reinforced Unsaturated Polyester Composite

2013 ◽  
Vol 465-466 ◽  
pp. 962-966 ◽  
Author(s):  
Mohd Pahmi bin Saiman ◽  
Mohd Saidin Bin Wahab ◽  
Mat Uzir Wahit
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Linear Density ◽  
Unsaturated Polyester ◽  
Composite Panel ◽  
Composite Yarn ◽  
Polyester Composite ◽  
The Impact ◽  
Woven Kenaf

To produce a good quality of dry fabric for reinforced material in a natural-based polymer composite, yarn linear density should be in consideration. A woven kenaf dry fabric with three different linear densities of 276tex, 413.4tex and 759tex were produced. The fabrics with different linear densities were been optimize with the assistance of WiseTex software. The optimized dry fabrics were infused with unsaturated polyester to produce composite panel using vacuum infusion process. The composites properties were tested on the tensile strength, flexural strength and the impact strength. The result shows that the mechanical properties of the composite increased when the yarn linear densities increased.

scholarly journals The Effect of Borax Solution as Preservative to the Mechanical Properties of Bamboo

2020 ◽  
Vol 11 (2) ◽  
Author(s):  
M.A.P Handana ◽  
◽  
Besman Surbakti ◽  
Rahmi Karolina ◽  
◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Bending Strength ◽  
Environmentally Friendly ◽  
Preservative Solution ◽  
Borax Solution ◽  
Preservative Solutions

The use of borax solution as a preservative in wood and bamboo materials is well known in the community. A borax solution is an environmentally friendly liquid that can dissolve in water, so it is suitable to be used as a preservative within cold or hot soaking techniques. The ability of borax to resist insects and fungus attacks on bamboo has been proven, but the effect of the solution on the strength of bamboo must also be investigated. This study conducts to investigate the effects of borax and its additives as preservative solutions to the mechanical properties of bamboos. The bamboos preservations were conducted by cold conditions of immersion, while the mechanical properties were performed to understand the effects of preservatives. The result of this study indicated that 30% to 50% borax in the preservative solution is sufficient to provide significant increase in strength for compressive strength, tensile strength, and bending strength of bamboo specimen. From this study, the use of borax solution in preserving the bamboos materials improved the quality of bamboos based on its mechanical properties.

scholarly journals The Impact of Slicing Softwares on the Mechanical Properties of 3D Printed Parts

2020 ◽  
Vol 9 (2) ◽  
pp. 487-494
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
3D Printer ◽  
Stl File ◽  
3D Printed ◽  
Intersection Curves ◽  
The Impact

“Slicing tool” or “Slicing Software” computes the intersection curves of models and slicing planes. They improve the quality of the model being printed when given in the form of STL file. Upon analyzing a specimen that has been printed using two different slicing tools, there was a drastic variation on account of the mechanical properties of the specimen. The ultimate tensile strength and the surface roughness of the material vary from one tool to another. This paper reports an investigation and analysis of the variation in the ultimate tensile strength and the surface roughness of the specimen, given that the 3D printer and the model being printed is the same, with a variation of usage of slicing software. This analysis includes ReplicatorG, Flashprint as the two different slicing tools that are used for slicing of the model. The variation in the ultimate tensile strength and the surface roughness are measured and represented statistically through graphs. An appropriate decisive conclusion was drawn on the basis of the observations and analysis of the experiment on relevance to the behavior and mechanical properties of the specimen.

scholarly journals PENGARUH PERBEDAAN BAHAN PENYAMAK TERHADAP KUALITAS KULIT IKAN PARI MONDOL (Himantura gerrardi) TERSAMAK The Effect of Different Tanning Materials towards Leather Quality of Tanned Mondol Stingray (Himantura gerrardi)

2016 ◽  
Vol 11 (2) ◽  
pp. 140
Author(s):  
Tika Kusmaryanti ◽  
Ratna Ibrahim ◽  
Putut Har Riyadi
Keyword(s):  
Tensile Strength ◽  
Moisture Content ◽  
Ph Value ◽  
Block Design ◽  
Shrinkage Temperature ◽  
Quality Requirements ◽  
Tear Strength ◽  
Randomized Block Design ◽  
Significant Difference

ABSTRAK   Usaha penyamakan kulit ikan Pari umumnya dilakukan oleh usaha kecil menengah dan hanya menggunakan metode aldehid dengan bahan samak formalin, Selain itu juga belum diketahui kualitas kulit ikan Pari Mondol tersamak yang menggunakan bahan samak krom. Penelitian ini bertujuan untuk mengetahui pengaruh perbedaan penggunaan jenis bahan penyamak terhadap kualitas fisik dan kimiawi kulit ikan Pari Mondol tersamak. Materi penelitian berupa kulit ikan Pari Mondol (Himantura gerrardi) dan bahan samak. Penelitian dilakukan dengan metode eksperimental laboratoris. Rancangan percobaan yang digunakan adalah Rancangan Acak Kelompok dengan perlakuan bahan samak yang berbeda, yaitu formalin, krom, dan kombinasi. Masing-masing perlakuan diulang tiga kali. Variabel mutu yang diamati adalah kekuatan tarik, kemuluran, kekuatan sobek, ketebalan, suhu kerut, ketahanan bengkuk (bengkok), pH dan kadar air. Data dianalisis menggunakan ANOVA dan perbedaan diantara perlakuan diuji dengan Uji Tukey. Hasil penelitian menunjukkan bahwa perbedaan bahan penyamak menyebabkan pengaruh nyata terhadap nilai kekuatan tarik, kekuatan sobek dan ketebalan tetapi tidak memberikan pengaruh nyata terhadap nilai pH, kadar air dan ketahanan bengkuk. Produk yang terbaik yaitu kulit ikan Pari Mondol yang disamak dengan bahan samak kombinasi antara krom dan mimosa, yang sebagian persyaratan mutunya sudah memenuhi persyaratan mutu kulit ikan Pari tersamak menurut SNI 06-6121-1999.   Kata kunci: Kualitas, kulit Ikan Pari, penyamak     ABSTRACT  Meanwhile the quality of Stingray tanned leather which using chrome tannin materials was not yet known. This research aims to determine the effect of different types used tannin materials towards physical and chemical quality of Stingray leather quality. The materials used in this research isStingray (Himantura gerrardi) skin and tannin materials. The study was conducted with laboratory experimental method. The experiments was designed according to the Randomized Block Design with different tanning materials (formalin, chrome, and chrome-combination). Each treatment was done with in triplicate. The quality variables that measured were tensile strength, elongation, tear strength, thickness, shrinkage temperature, bent resistance, pH and moisture content. Data were analyzed using Analysis of Variance. To find the difference between treatments, the data were tested with Honestly Significant Difference Test . The results showed that various of tannin materials gave significant effects to the values of tensile strength, tear strength and thickness however there was not any significant effect on bent resistance, moisture content and pH value. The best product were Stingray tanned leather with chrome-combination tannin material, which partially quality requirements has been comply with Stingray tanned leather quality requirements according to SNI. Keywords: Quality, stingray skin, tanning

scholarly journals Low-Pressure Membrane for Water Treatment Applications

2020 ◽  
Vol 2020 ◽  
pp. 1-7
Author(s):  
Huda AlFannakh ◽  
Heba Abdallah ◽  
S. S. Ibrahim ◽  
Basma Souayeh
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Drinking Water ◽  
Humic Acid ◽  
Tap Water ◽  
Permeate Flux ◽  
Membrane Performance ◽  
Polyethersulfone Membrane ◽  
Contaminated Drinking Water

Three ultrafiltration membranes were prepared using phase separation techniques. The membranes were characterized by scan electron microscope, porosity, pore size distribution measurement, and mechanical properties. The membrane performance was carried out using synthetic solutions from humic acid and tap water to express the contaminated drinking water. The polyvinylidene difluoride (M2) has the highest tensile strength 33.2 MPa with elongation of 52.3%, while polyacrylonitrile (M3) has the lowest mechanical properties, tensile strength 16.4 MPa with elongation of 42.7%. Polyethersulfone membrane (M1) provides the highest removal of humic acid, which was 99.5, 98.8, and 98.2% using feed concentrations 0.1, 0.3, and 0.5 g/l, respectively, while M3 provides the highest permeate flux which was 250, 234.4, and 201.4 l/m2 h using feed concentrations 0.1, 0.3, and 0.5 g/l, respectively. Analysis of water samples indicates that the prepared membranes can be used to treat the contaminated drinking water which produced the high quality of drinking water after treatment.

Effect of Atmosphere and Holding Time on the Quality of Surface and Mechanical Properties of the Cold-Rolling Plate of Fe-42% Ni (4J42)

2012 ◽  
Vol 560-561 ◽  
pp. 655-660
Author(s):  
Li Juan Li ◽  
Li Hua Liu ◽  
Jing Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Yield Strength ◽  
Cold Rolling ◽  
Surface Quality ◽  
Annealing Process ◽  
Holding Time ◽  
Annealing Condition ◽  
Nitrogen Ratio

In order to guide atmosphere annealing process in industry, the effect of atmosphere and holding times on the surface quality and mechanical properties of the cold-rolling plate of Fe-42% Ni (4J42) was studied. It is found that in the laboratory, surface qualities of all the samples annealed at different annealing condition are all good enough. When the ratio of hydrogen and nitrogen is below 70%:30%, at different holding time, with increasing of H2 proportion, 4J42’s tensile strength and yield strength all increases, and the hardness declines. And except H2:N2=70%:30, when holding time is less than or equal to 1.2min, at different ratio of hydrogen and nitrogen, holding time will influence 4J42’s mechanical properties little. So combine requires in industry with the experiment results, it can be concluded that for 4J42 alloy, annealing at atmosphere of hydrogen nitrogen ratio is less than 70%:30% for about 1.2min is appropriate to atmosphere annealing process in industry.

scholarly journals Analisis Sifat Mekanik Hasil Pengelasan SMAW dengan Akar Las Tig dan Las SMAW pada Pipa API 5L

2019 ◽  
Vol 17 (1) ◽  
pp. 37
Author(s):  
Muas M ◽  
Muhammad Arsyad Suyuti ◽  
Rasul Rasul ◽  
Patta Hajji
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Bending Strength ◽  
Mechanical Tests ◽  
Current Variation ◽  
Root Face ◽  
A Current ◽  
Root Methods ◽  
Made In

The purpose of this research is to know the mechanical properties of the welds due to the current variation of welding joint API 5L using TIG and SMAW welding root methods. Preparation of specimens of pipe API 5L PSL1 grade X56 (Ø 177.8 mm, length 200 mm, width 7 mm), then specimens preparation were made in a single V 600, root gap 2mm, root face 2mm. Filling the welding roots with TIG welding and SMAW using electrodes E7018 with a current variation 70A, 80A, 90A. Mechanical tests consist of tensile, bending and hard test. The results showed that the quality of a good TIG root weld at 70A, the highest tensile strength of the weld joint 52.27 kgf/mm2 (70A), the highest hardnest 164,217 HRB (90A), the bending strength 1.123,061 N/mm2 (70A) using face bend method and 1,172,959 N/mm2 with root bend. In SMAW root welding, the highest tensile strength 54.27 kgf/mm2 (70 A) , the highest hardnest  158.717 HRB (70 A), the highest bending strength 1.115,611 N/mm2 (70 A) using face bend method, and 1.161,748 N/ mm2 with root bend. 

scholarly journals COMPARATIVE EVALUATION OF EFFECT OF TWO LIGHT CURING UNITS ON MECHANICAL PROPERTIES OF FILTEK BULK FILL COMPOSITE

2021 ◽  
Vol 9 (02) ◽  
pp. 104-110
Author(s):  
Akshay Punjabi ◽  
◽  
Rahul Rao ◽  
Ashish K. Jain ◽  
Meenakshi Verma ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Testing Machine ◽  
Dental Composite ◽  
Light Curing ◽  
Circular Rings ◽  
The Difference ◽  
Diametral Tensile Strength

Context:The quality of light curing units can profoundly influence mechanical properties of dental composite materials. Aim: To compare effect of Woodpecker RTA Mini-S and Elipar Deep Cure-L curing units onmechanical properties (compressive strength, diametral tensile strength and microhardness) of Filtek Bulk-Fill. Methods and Materials: A total of 32 samples of Filtek Bulk Fill composite were divided into 2 equal groups (n=16). 12 samples in each group were fabricated using a tooth shaped mold and 4 in circular rings to test compressive strength, microhardness and diametral tensile strength, respectively. Theblocks were evaluated for the above parameters using Universal Testing Machine and Vickers Microhardness Tester.Independent sample-t test was used in this study (p< 0.05). Results: The results of this study showed that the group of composites cured using Elipar Deep Cure-L curing unit showed better mechanical properties and the difference between the groups was statistically significant for compressive strength and diametral tensile strength (p < 0.05) Conclusion: It was concluded that a curing unit of higher intensity and quality of output used in conjugation with bulk fill composites are likely to give better results.

Properties of VA/E/MMA Terpolymer Powder-Modified Mortars

2015 ◽  
Vol 1129 ◽  
pp. 169-176
Author(s):  
Sunhee Hong ◽  
Wan Ki Kim
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Cement Mortar ◽  
Mercury Porosimetry ◽  
Chloride Ion ◽  
Test Results ◽  
Polymer Powder ◽  
Chloride Ion Penetration ◽  
Redispersible Polymer Powder

This study is to examine and clarify the quality of polymer-modified mortars using a VA/E/MMA terpolymer powder as compared with polymer-modified mortars using a VAE copolymer powder. Polymer-modified mortars using general commercial redispersible polymer powders are prepared with various polymer-cement ratios, and tested for flexural and compressive strengths, tensile strength, water absorption, chloride ion penetration, carbonation and pore size distribution by mercury porosimetry. Overall, the properties of polymer-modified mortars using a VA/E/MMA terpolymer powder were superior to those of polymer-modified mortars using a VAE copolymer powder. And VA/E/MMA terpolymer powder-modified mortars showed significantly improved mechanical properties and durability in comparison with unmodified mortar. It is concluded from the test results that the modification of cement mortar with redispersible polymer powder improves the properties of unmodified mortar, and VA/E/MMA terpolymer powder has higher quality than VAE copolymer powder.

Sign in / Sign up

Export Citation Format

Share Document