Development of Wood-Based Composites Material for 3D Printing Process

2013 ◽  
Vol 315 ◽  
pp. 987-991 ◽  
Author(s):  
Wahab Saidin ◽  
Abdullah Wagiman ◽  
Mustaffa Ibrahim
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Surface Quality ◽  
Low Cost ◽  
Three Dimensional ◽  
Dimensional Accuracy ◽  
Wood Powder ◽  
Powder Preparation ◽  
Printing Process ◽  
Powder Content

This paper presents the development of wood-based composites material for 3D Printing process. The aim is to characterize the waste material from wood powder (WD) as an alternative material and low cost production for rapid prototyping product. The powder blends containing wood powder (90-120µm) with commercial ZP102 material from Z Corporation was used as the composite material. The materials were mechanically blended to produce composition of WD/ZP102(vol.%) 25:70, 50:50 and 75:25 respectively. The material was successfully processed on 3D printers machine, to produce three-dimensional components and followed by post-treatment with ZMax solution to enhance the mechanical properties. The mechanical properties, dimensional accuracy and surface quality of the components were evaluated and the results were compared with the standard ZP102 material. The result shows that the mechanical properties improved with the increased of wood powder content up to 50 (vol.%). However, dimensional accuracy and surface quality were decreased as the wood content increased. Further work on powder preparation is continued for surface quality improvement.

scholarly journals Analysis of Mechanical Properties of Polylactic Acid Using a New 3D Printer Nozzle

2018 ◽  
Vol 15 (2) ◽  
pp. 666-675
Author(s):  
Nor Aiman Sukindar ◽  
Mohd Khairol Anuar Mohd Ariffin ◽  
B. T. Hang Tuah Baharudin ◽  
Che Nor Aiza Jaafar ◽  
Mohd Idris Shah Ismail
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Polylactic Acid ◽  
Low Cost ◽  
Three Dimensional ◽  
Extrusion Process ◽  
3D Printer ◽  
Layer By Layer ◽  
The Stability ◽  
Stability And Accuracy

Additive manufacturing, also known as three-dimensional (3D) printing, is the process of developing 3D products in a layer-by-layer manner using filament as a material feedstock to create a solid structure. Owing to its unique properties and advantages, which include biodegradability and printing speed, polylactic acid is one of the most common 3D printing extrusion materials. While a considerable attention has been paid to the manipulation of process parameters in order to achieve desired finished product quality, to date less research has been performed on improving the hardware systems of low-cost 3D printers. This study focuses on fabricating the 3D printer nozzle parts, with an emphasis on die angle, nozzle diameter, liquefier design, and insulator composition. Modifying the properties of these components from the conventional nozzle, it is possible to optimize the stability and accuracy of the extrusion process, leading to better-quality printed products. To demonstrate the capability of the new nozzle, its tensile and compressive strengths were compared to those of a conventional nozzle. The obtained results proved that the proposed augmentations to the nozzle system lead to finished products with improved mechanical properties.

scholarly journals Evaluating Temperature Influence on Low-Cost Piezoelectric Transducer Response for 3D Printing Process Monitoring

Proceedings ◽  
2019 ◽  
Vol 42 (1) ◽  
pp. 26
Author(s):  
Thiago Glissoi Lopes ◽  
Renata Maia Rocha ◽  
Paulo Roberto Aguiar ◽  
Felipe Aparecido Alexandre ◽  
Thiago Valle França
Keyword(s):  
3D Printing ◽  
Piezoelectric Transducer ◽  
Low Cost ◽  
Three Dimensional ◽  
Signal Amplitude ◽  
Acceptable Error ◽  
Temperature Variations ◽  
Printing Process ◽  
Frequency Bands ◽  
Low Sensitivity

The 3D printing process deals with the production of three-dimensional objects with defined geometries. However, this manufacturing process has a crucial point established at the beginning of the object manufacturing, where anomalies can occur and compromise the entire object produced. The piezoelectric diaphragm has been studied as an alternative to the conventional acoustic emission (AE) sensor concerning the monitoring of structures and processes. It has in its assembling a ceramic element with piezoelectric properties, which makes its response sensitive to temperature variations. The Pencil Lead Break (PLB) method is widely used due to its efficiency in the characterization of AE sensors. The present work aims to study the influence of temperature on the piezoelectric diaphragm response for the monitoring of the 3D printing process. PLB tests were performed on the glass surface of a 3D printer at three different temperatures, and the raw signal was collected at 5 MHz sample rate. The signal was investigated in the time and frequency domain. The results demonstrate that the frequency response of the sensor is directly influenced by the temperature variations. In addition, the signal amplitude variations occur differently along the entire spectrum, and frequency bands with small and large amplitude variations can be selected for a comparison study. Furthermore, two frequency bands were carefully selected, and the mean error was obtained regarding the reference temperatures of 25 and 45 °C. It can be inferred that the piezoelectric transducer has low sensitivity to temperature variation if a proper frequency band is selected, where an acceptable error of 16.9% was obtained.

scholarly journals An Overview on the Rheology, Mechanical Properties, Durability, 3D Printing, and Microstructural Performance of Nanomaterials in Cementitious Composites

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2950
Author(s):  
Hongwei Song ◽  
Xinle Li
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Three Dimensional ◽  
Cementitious Materials ◽  
Research Area ◽  
Cementitious Composites ◽  
Split Tensile Strength ◽  
Contour Crafting ◽  
Wide Range ◽  
Active Research

The most active research area is nanotechnology in cementitious composites, which has a wide range of applications and has achieved popularity over the last three decades. Nanoparticles (NPs) have emerged as possible materials to be used in the field of civil engineering. Previous research has concentrated on evaluating the effect of different NPs in cementitious materials to alter material characteristics. In order to provide a broad understanding of how nanomaterials (NMs) can be used, this paper critically evaluates previous research on the influence of rheology, mechanical properties, durability, 3D printing, and microstructural performance on cementitious materials. The flow properties of fresh cementitious composites can be measured using rheology and slump. Mechanical properties such as compressive, flexural, and split tensile strength reveal hardened properties. The necessary tests for determining a NM’s durability in concrete are shrinkage, pore structure and porosity, and permeability. The advent of modern 3D printing technologies is suitable for structural printing, such as contour crafting and binder jetting. Three-dimensional (3D) printing has opened up new avenues for the building and construction industry to become more digital. Regardless of the material science, a range of problems must be tackled, including developing smart cementitious composites suitable for 3D structural printing. According to the scanning electron microscopy results, the addition of NMs to cementitious materials results in a denser and improved microstructure with more hydration products. This paper provides valuable information and details about the rheology, mechanical properties, durability, 3D printing, and microstructural performance of cementitious materials with NMs and encourages further research.

scholarly journals Extrusion Based 3D Printing of Sustainable Biocomposites from Biocarbon and Poly(trimethylene terephthalate)

Molecules ◽  
2021 ◽  
Vol 26 (14) ◽  
pp. 4164
Author(s):  
Elizabeth Diederichs ◽  
Maisyn Picard ◽  
Boon Peng Chang ◽  
Manjusri Misra ◽  
Amar Mohanty
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Surface Finish ◽  
Three Dimensional ◽  
Morphological Properties ◽  
Great Promise ◽  
Structural Components ◽  
Computer Aided ◽  
Trimethylene Terephthalate ◽  
Optimal Quantity

Three-dimensional (3D) printing manufactures intricate computer aided designs without time and resource spent for mold creation. The rapid growth of this industry has led to its extensive use in the automotive, biomedical, and electrical industries. In this work, biobased poly(trimethylene terephthalate) (PTT) blends were combined with pyrolyzed biomass to create sustainable and novel printing materials. The Miscanthus biocarbon (BC), generated from pyrolysis at 650 °C, was combined with an optimized PTT blend at 5 and 10 wt % to generate filaments for extrusion 3D printing. Samples were printed and analyzed according to their thermal, mechanical, and morphological properties. Although there were no significant differences seen in the mechanical properties between the two BC composites, the optimal quantity of BC was 5 wt % based upon dimensional stability, ease of printing, and surface finish. These printable materials show great promise for implementation into customizable, non-structural components in the electrical and automotive industries.

scholarly journals Exceptional Mechanical Properties and Heat Resistance of Photocurable Bismaleimide Ink for 3D Printing

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1708
Author(s):  
Wenqiang Hua ◽  
Qilang Lin ◽  
Bo Qu ◽  
Yanyu Zheng ◽  
Xiaoying Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Heat Resistance ◽  
Three Dimensional ◽  
Mechanical And Thermal Properties ◽  
Amino Group ◽  
Building Models ◽  
Fast Processing ◽  
Forming Precision ◽  
Complex Structural

Photosensitive resins used in three-dimensional (3D) printing are characterized by high forming precision and fast processing speed; however, they often possess poor mechanical properties and heat resistance. In this study, we report a photocurable bismaleimide ink with excellent comprehensive performance for stereolithography (SLA) 3D printing. First, the main chain of bismaleimide with an amino group (BDM) was synthesized, and then, the glycidyl methacrylate was grafted to the amino group to obtain the bismaleimide oligomer with an unsaturated double bond. The oligomers were combined with reaction diluents and photo-initiators to form photocurable inks that can be used for SLA 3D printing. The viscosity and curing behavior of the inks were studied, and the mechanical properties and heat resistance were tested. The tensile strength of 3D-printed samples based on BDM inks could reach 72.6 MPa (166% of that of commercial inks), glass transition temperature could reach 155 °C (205% of that of commercial inks), and energy storage modulus was 3625 MPa at 35 °C (327% of that of commercial inks). The maximum values of T-5%, T-50%, and Tmax of the 3D samples printed by BDM inks reached 351.5, 449.6, and 451.9 °C, respectively. These photocured BDM inks can be used to produce complex structural components and models with excellent mechanical and thermal properties, such as car parts, building models, and pipes.

scholarly journals An Application of Integrated 3D Technologies for Replicas in Cultural Heritage

2019 ◽  
Vol 8 (6) ◽  
pp. 285 ◽  
Author(s):  
Balletti ◽  
Ballarin
Keyword(s):  
3D Printing ◽  
Cultural Heritage ◽  
Laser Scanning ◽  
Low Cost ◽  
Three Dimensional ◽  
Digital Data ◽  
Survey Analysis ◽  
Critical Issues ◽  
Data Acquisition And Processing ◽  
Short Time

In recent decades, 3D acquisition by laser scanning or digital photogrammetry has become one of the standard methods of documenting cultural heritage, because it permits one to analyze the shape, geometry, and location of any artefact without necessarily coming into contact with it. The recording of three-dimensional metrical data of an asset allows one to preserve and monitor, but also to understand and explain the history and cultural heritage shared. In essence, it constitutes a digital archive of the state of an artefact, which can be used for various purposes, be remodeled, or kept safely stored. With the introduction of 3D printing, digital data can once again take on material form and become physical objects from the corresponding mathematical models in a relatively short time and often at low cost. This possibility has led to a different consideration of the concept of virtual data, no longer necessarily linked to simple visual fruition. The importance of creating high-resolution physical copies has been reassessed in light of different types of events that increasingly threaten the protection of cultural heritage. The aim of this research is to analyze the critical issues in the production process of the replicas, focusing on potential problems in data acquisition and processing and on the accuracy of the resulting 3D printing. The metric precision of the printed model with 3D technology are fundamental for everything concerning geomatics and must be related to the same characteristics of the digital model obtained through the survey analysis.

scholarly journals Effects of Sintering Behaviors on Dimensional Accuracy, Surface Quality, and Mechanical Properties of Stereolithography-printed 3Y-ZrO2 Ceramics

2021 ◽  
Author(s):  
Cheng Zhang ◽  
Zhaoliang Jiang ◽  
Li Zhao ◽  
Weiwei Guo ◽  
Chengpeng Zhang
Keyword(s):  
Mechanical Properties ◽  
Dental Implants ◽  
Surface Quality ◽  
Dimensional Accuracy ◽  
Scanning Speed ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
Air Atmosphere ◽  
Length Width ◽  
Technical Guide

Abstract Sintering process is essential to acquire the final components by stereolithography (SLA), which is a promising additive manufacturing technology for the fabrication of complex, custom-designed dental implants. 3Y-ZrO2 ceramics at different sintering behaviors in air atmosphere were successfully obtained in this study. Firstly, the curing properties of homemade pastes were studied, and the penetration depth and critical exposure of the pastes were calculated as 17.2 μm and 4.80 mJ/cm2, respectively. The green ceramic parts were performed at 154 mW laser power and 6000 mm/s scanning speed. Then, the dimensional accuracy, surface quality, and mechanical properties of 3Y-ZrO2 ceramics were investigated. The shrinkages of length, width, and height were 26%~27 %, 30%~31 %, and 27%~33 % in sintered ceramics, respectively. The Ra values of XOY, YOZ, and XOZ surfaces showed an anisotropic feature, and they were smallest as 0.52 μm, 2.40 μm, and 2.46 μm, respectively. Meanwhile, the mechanical properties presented a similar trend that they grew first and then dropped at various sintering behaviors. The optimal parameters were 1500 ℃, 60 min, and 4 ℃/min, and the maximum relative density of 96.18 %, Vickers hardness of 12.45 GPa, and fracture toughness of 6.35 MPa·m1/2 were achieved. Finally, the X-ray diffraction (XRD) and energy-dispersive spectroscopy (EDS) analysis demonstrated that no change was observed in crystal transformation and phase composition, and the organic was completely removed in sintered ceramics. This research is expected to provide a technical guide for the fabrication of ceramics for dental implants using SLA technique.

scholarly journals Design and implementation of a three dimensions (3D) printer for modeling and pre-manufacturing applications

2019 ◽  
Vol 9 (6) ◽  
pp. 4749
Author(s):  
Ghazi Qaryouti ◽  
Abdel Rahman Salbad ◽  
Sohaib A. Tamimi ◽  
Anwar Almofleh ◽  
Wael A. Salah ◽  
...  
Keyword(s):  
3D Printing ◽  
Manufacturing Sector ◽  
Low Cost ◽  
Three Dimensional ◽  
Three Dimensions ◽  
3D Printer ◽  
Overall Design ◽  
Design And Implementation ◽  
Manufacturing Applications ◽  
Functional Components

The three-dimensional (3D) printing technologies represent a revolution in the manufacturing sector due to their unique characteristics. These printers arecapable to increase the productivitywithlower complexity in addition tothe reduction inmaterial waste as well the overall design cost prior large scalemanufacturing.However, the applications of 3D printing technologies for the manufacture of functional components or devices remain an almost unexplored field due to their high complexity. In this paper the development of 3D printing technologies for the manufacture of functional parts and devices for different applications is presented. The use of 3D printing technologies in these applicationsis widelyused in modelingdevices usually involves expensive materials such as ceramics or compounds. The recent advances in the implementation of 3D printing with the use of environmental friendly materialsin addition to the advantages ofhighperformance and flexibility. The design and implementation of relatively low-cost and efficient 3D printer is presented. The developed prototype was successfully operated with satisfactory operated as shown from the printed samples shown.

Experimental study on the accuracy and surface quality of printed versus machined holes in PEI Ultem 9085 FDM specimens

2021 ◽  
Vol 27 (11) ◽  
pp. 1-12
Author(s):  
Giovanni Gómez-Gras ◽  
Marco A. Pérez ◽  
Jorge Fábregas-Moreno ◽  
Guillermo Reyes-Pozo
Keyword(s):  
Surface Quality ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Dimensional Accuracy ◽  
Technological Parameters ◽  
Content Type ◽  
Fused Deposition ◽  
Comparison Of The Results ◽  
Through Hole

Purpose This paper aims to investigate the quality of printed surfaces and manufacturing tolerances by comparing the cylindrical cavities machined in parts obtained by fused deposition modeling (FDM) with the holes manufactured during the printing process itself. The comparison focuses on the results of roughness and tolerances, intending to obtain practical references when making assemblies. Design/methodology/approach The experimental approach focuses on the comparison of the results of roughness and tolerances of two manufacturing strategies: geometric volumes with a through-hole and the through-hole machined in volumes that were initially printed without the hole. Throughout the study, both alternates are explained to make appropriate recommendations. Findings The study shows the best combinations of technological parameters, both machining and three-dimensional printing, which have been decisive for obtaining successful results. These conclusive results allow enunciating recommendations for use in the industrial environment. Originality/value This paper fulfills an identified need to study the dimensional accuracy of the geometries obtained by additive manufacturing, as no experimental evidence has been found of studies that directly address the problem of the FDM-printed part with geometric and dimensional tolerances and desirable surface quality for assembly.

scholarly journals Strength Characteristics and the Reaction Mechanism of Stone Powder Cement Tailings Backfill

2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
Jianhua Hu ◽  
Qifan Ren ◽  
Quan Jiang ◽  
Rugao Gao ◽  
Long Zhang ◽  
...  
Keyword(s):  
Reaction Mechanism ◽  
Early Stage ◽  
Low Cost ◽  
Three Dimensional ◽  
Adsorbed Water ◽  
Gelling Agent ◽  
Hydration Reaction ◽  
3D Network ◽  
Mining Procedure ◽  
Powder Content

Stone powder cement (SPC) is widely used as a novel cement substitute material in concrete for its good gelling performance and low cost. In order to reduce the backfilling cost and assess the potential of SPC backfilling materials, a series of experiments were conducted to analyze the strength and hydration reaction mechanism of stone powder cement tailings backfill (SPCTB). The analysis was based on SPC and tailings, which were used as the gelling agent and the aggregate, respectively. The results showed that the strength of the backfill was greatly reduced at an early stage and slightly reduced in the final stages. The stone powder content was less than 15%, which met the requirement of mining procedure. The addition of stone powder reduced the content of adsorbed water and capillary water in the early stages, while it increased in the middle stages. The SiO2 contained in stone powder reacted with the hydration products at later stages, which is the reason why the growth of strength is rapid between the groups with the addition of stone powder. The addition of stone powder improved the microstructure of backfill and produced a denser three-dimensional (3D) network structure; however, the plane porosities of Groups A and B gradually increased with the increase in the content of stone powder. The cement powder mixed appropriately with the stone power could meet the strength requirement and reduce the cost of backfilling materials.

Sign in / Sign up

Export Citation Format

Share Document