Application of Bamboo Shoot Shell in Color Removal from Methylene Blue Solution

2014 ◽  
Vol 675-677 ◽  
pp. 489-492
Author(s):  
Jing Miao Zhang ◽  
Zhi Wei Zhong ◽  
Da Pan Zhu ◽  
Lin Man Lin ◽  
Qing Ju Wang ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Removal Efficiency ◽  
Ph Value ◽  
Color Removal ◽  
Target Color ◽  
Maximum Adsorption Capacity ◽  
Bamboo Shoot ◽  
Blue Solution ◽  
Optimized Conditions

Biosorption of dyeing wastewater is most widely used method so far. The adsorption of methylene blue (MB) with bamboo shoot shell (BSS) as biosorbent was investigated. Orthogonal test was used to optimize the adsorption process, and adsorption capacity and color removal efficiency were used to judge the adsorptivity of BSS. Results showed that maximum adsorption capacity was 225.71 mg·g-1, and color removal efficiency could achieve to 98.96% during the test. To obtain best adsorption capacity, the optimized conditions of temperature, initial concentration of dye, BSS dosage, pH value and adsorption time were 45 °C, 400 mg·L-1, 10 mg/10 mL, 9.6 and 30 min, respectively. As to another target color removal efficiency, the best parameters were 100 mg·L-1, 200 mg/10 mL, 11.5 and 120 min, respectively. The results reveal that the agricultural by-product BSS is an effective biosorbent.

Insights into the mechanism of methylene blue removed by novel and classic biochars

2019 ◽  
Vol 79 (8) ◽  
pp. 1561-1570
Author(s):  
Wei Chen ◽  
Fengting Chen ◽  
Bin Ji ◽  
Lin Zhu ◽  
Hongjiao Song
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Ph Value ◽  
Low Cost ◽  
Underlying Mechanism ◽  
Maximum Adsorption Capacity ◽  
Experimental Conditions ◽  
Average Pore ◽  
Adsorption Effect ◽  
Magnolia Grandiflora

Abstract The adsorption behavior and the underlying mechanism of methylene blue (MB) sorption on biochars prepared from different feedstocks at 500 °C were evaluated. The biochar feedstocks included Magnolia grandiflora Linn. leaves biochar (MBC), pomelo (Citrus grandis) peel biochar (PBC) and badam shell biochar (BBC). The results of characterizing and analyzing the samples showed that different biochars had different effects on the adsorption of MB. It could be found that MBC had the best adsorption effect on MB due to its largest average pore diameter of 5.55 nm determined by Brunauer-Emmett-Teller analysis. Under the optimal conditions, the maximum adsorption capacities of BBC, PBC and MBC were 29.7, 85.15 and 99.3 mg/g, respectively. The results showed that the amount of adsorption was affected by the pH value. The maximum adsorption capacity of MBC was 46.99 mg/g when it was at pH of 3, whereas for the same experimental conditions the maximum adsorption capacity of BBC and PBC was 25.29 mg/g at pH of 11 and 36.08 mg/g at pH of 7, respectively. Therefore, MBC was found to be a most efficient low-cost adsorbentl for dye wastewater treatment compared with BBC and PBC, and it had the best removal effect under acidic conditions.

scholarly journals Synthesis of a Novel Ce-bpdc for the Effective Removal of Fluoride from Aqueous Solution

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Changqing Zhao ◽  
Yanwei Cui ◽  
Fang Fang ◽  
Si Ok Ryu ◽  
Jiarui Huang
Keyword(s):  
Adsorption Capacity ◽  
Removal Efficiency ◽  
Photoelectron Spectroscopy ◽  
Ph Value ◽  
Binding Capacity ◽  
Fluoride Removal ◽  
Maximum Adsorption Capacity ◽  
Fluoride Ions ◽  
X Ray ◽  
Fluoride Adsorption

Ce-1,1′-biphenyl-4,4′-dicarboxylic acid (Ce-bpdc), a novel type of metal organic framework, was synthesized and applied to remove excessive fluoride from water. The structure and morphology of Ce-bpdc were measured by X-ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. The effects, such as saturated adsorption capacity, HCO3-, and pH, were investigated. The optimal pH value for fluoride adsorption was the range from 5 to 6. The coexisting bicarbonate anions have a little influence on fluoride removal. The fluoride adsorption over the Ce-bpdc adsorbent could reach its equilibrium in about 20 min. The Ce-bpdc coordination complex exhibited high binding capacity for fluoride ions. The maximum adsorption capacity calculated from Langmuir model was high up to 45.5 mg/g at 298 K (pH = 7.0) and the removal efficiency was greater than 80%. In order to investigate the mechanism of fluoride removal, various adsorption isotherms such as Langmuir and Freundlich were fitted. The experimental data revealed that the Langmuir isotherm gave a more satisfactory fit for fluoride removal. Finally, the tested results of ground water samples from three places, Yuefang, Jiangji, and Sanyi which exhibited high removal efficiency, also demonstrate the potential utility of the Ce-bpdc as an effective adsorbent.

scholarly journals Study on Adsorption of Nickel and Methylene Blue in Aqueous Solution by Magnetic Carboxylate-Rich Carbon

2021 ◽  
Vol 37 (2) ◽  
Author(s):  
Doan Van Dat ◽  
Nguyen Hoai Thuong ◽  
Tran Thi Kieu Ngan ◽  
Le Thi Thanh Nhi ◽  
Dao My Uyen ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Adsorption Capacity ◽  
Ph Value ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
High Adsorption ◽  
Endothermic Process ◽  
High Adsorption Capacity

In this study, magnetic carboxylate-rich carbon material (Fe3O4@CRC) was synthesized via a low-temperature carbonization method and applied as an adsorbent for adsorption of Ni(II) ions and methylene blue (MB) in aqueous solution. The synthesized Fe3O4@CRC was characterized by various techniques (XRD, FTIR, FE-SEM, TEM, EDX, VSM, and BET). The adsorption kinetics, isotherms, thermodynamics, and the effects of key adsorption factors, including the pH value, initial adsorbate concentration, contact time, adsorbent dose and temperature were investigated in detail. The results showed that Fe3O4@CRC exhibited a high adsorption capacity for MB and Ni(II) with the maximum adsorption capacity of 187.26 mg/g and 106.75 mg/g, respectively. The adsorption of MB and Ni(II) on Fe3O4@CRC was a spontaneous and endothermic process, and was best described with the first-order kinetic model, Freundlich (for MB) and Langmuir (for Ni(II)) isotherm models. In addition, Fe3O4@CRC could maintain a high adsorption capacity after many consecutive cycles. Therefore, the Fe3O4@CRC material can be used as a highly efficient adsorbent for the removal of heavy metals and dyes from wastewater due to the advantages of high adsorption performance, easy separation, and good reusability.  

Adsorption and Catalysis of Orange II from Wastewater by Inorganic-Organic-Bentonite

2011 ◽  
Vol 340 ◽  
pp. 236-240
Author(s):  
Jian Feng Ma ◽  
Jian Ming Yu ◽  
Bing Ying Cui ◽  
Ding Long Li ◽  
Juan Dai
Keyword(s):  
Adsorption Capacity ◽  
Removal Efficiency ◽  
Dye Removal ◽  
Maximum Adsorption Capacity ◽  
Orange Ii ◽  
Acid Dye ◽  
Secondary Pollution ◽  
Organic Bentonite ◽  
Maximum Removal

Inorganic-organic-bentonite was synthesized by modification of bentonite by Hydroxy-iron and surfactant, which could be applied in dye removal by adsorption and catalysis. The removal of acid dye Orange II was studied at various factors such as time and pH of solution. The results showed that the inorganic-organic-bentonite could efficiently remove the dye with efficiency of 96.22%. The maximum adsorption capacity is 76 mg/g. The pH of solution has significant effect on both adsorption and catalysis. When pH was 4, the maximum removal efficiency of adsorption and catalysis were 97.57% and 87.23%, respectively. After degradation, the secondary pollution was diminished and the bentonite could be reused.

Ouricuri (Syagrus coronata) fiber: a novel biosorbent to remove methylene blue from aqueous solutions

2016 ◽  
Vol 75 (1) ◽  
pp. 106-114 ◽  
Author(s):  
Lucas Meili ◽  
Társila Santos da Silva ◽  
Daniely Carlos Henrique ◽  
João Inácio Soletti ◽  
Sandra Helena Vieira de Carvalho ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Experimental Design ◽  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Adsorption Process ◽  
Fiber Diameter ◽  
Aqueous Media ◽  
Process Efficiency ◽  
Maximum Adsorption Capacity ◽  
Equilibrium Studies

In this work, the potential of ouricuri (Syagrus coronata) fiber as a novel biosorbent to remove methylene blue (MB) from aqueous solutions was investigated. The fiber was prepared and characterized according to the fundamental features for adsorption. A 23 experimental design was used to evaluate the effects of adsorbent dosage (M), fiber diameter (D) and agitation (A) on the adsorption capacity. In the more adequate conditions, kinetic and equilibrium studies were performed. The experimental design results showed that M = 10 g L−1), D = 0.595 mm and A = 200 rpm were the more adequate conditions for MB adsorption. Based on the kinetic study, it was found that the adsorption process was fast, being the equilibrium was attained at about 5 min, with 90% of color removal. The isotherm was properly represented by the Sips model, and the maximum adsorption capacity was 31.7 mg g−1. In brief, it was demonstrated that ouricuri fiber is an alternative biosorbent to remove MB from aqueous media, taking into account the process efficiency and economic viewpoint.

scholarly journals Kinetic Study of the Bioadsorption of Methylene Blue on the Surface of the Biomass Obtained from the Algae D. antarctica

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Jhonatan R. Guarín ◽  
Juan Carlos Moreno-Pirajan ◽  
Liliana Giraldo
Keyword(s):  
Methylene Blue ◽  
Kinetic Study ◽  
Adsorption Capacity ◽  
Scientific Community ◽  
Second Order ◽  
Maximum Adsorption Capacity ◽  
Pseudo Second Order ◽  
Best Fit ◽  
Total Elimination ◽  
Purification Of Water

Currently, there is a great pollution of water by the dyes; due to this, several studies have been carried out to remove these compounds. However, the total elimination of these pollutants from the aquatic effluents has represented a great challenge for the scientific community, for which it is necessary to carry out investigations that allow the purification of water. In this work, we studied the bioadsorption of methylene blue on the surface of the biomass obtained from the algae D. antarctica. This material was characterized by SEM and FTIR. To the data obtained in the biosorption experiments, different models of biosorption and kinetics were applied, finding that the best fit to the obtained data is given by applying the pseudo-second-order models and the Toth model, respectively. It was also determined that the maximum adsorption capacity of MB on the surface of the biomass is 702.9 mg/g, which shows that this material has great properties as a bioadsorbent.

Adsorption of Methylene Blue from Aqueous Solution Using Honeycomb-Cinder

2012 ◽  
Vol 550-553 ◽  
pp. 2259-2262
Author(s):  
Song Bo Cui ◽  
Hua Yong Zhang ◽  
Lu Yi Zhang
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Ph Value ◽  
Dye Wastewater ◽  
Batch System ◽  
Adsorption Data ◽  
Adsorption Processes ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Mb Adsorption

The adsorption behavior of methylene blue (MB) dye from aqueous solutions onto honeycomb-cinder (HC) and its acid-activated product was investigated in a batch system. The results showed the adsorption capacity was decreased for raw HC samples with the increase of pH value, while it was increased for activated samples. The adsorption data were fit with Langmuir isotherm model for MB adsorption by all samples. The MB adsorption capacity on samples was increased from 2.62 mg/g to 7.81 mg/g and 7.00 mg/g after acid-activated by HCl and H2SO4, respectively. The adsorption processes of MB followed pseudo-second-order kinetics with a coefficient of correlation≥0.99. This study demonstrated that acid-activated HC has superior adsorbing ability for MB than raw HC and can be used as alternative adsorbents in dye wastewater treatment.

scholarly journals Adsorption of hexavalent chromium by polyacrylonitrile-based porous carbon from aqueous solution

2018 ◽  
Vol 5 (1) ◽  
pp. 171662 ◽  
Author(s):  
Bin Feng ◽  
Wenzhong Shen ◽  
Liyi Shi ◽  
Shijie Qu
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Porous Carbon ◽  
Photoelectron Spectroscopy ◽  
Ph Value ◽  
Functional Materials ◽  
High Specific Surface Area ◽  
Maximum Adsorption Capacity ◽  
Elementary Analysis ◽  
Initial Adsorption

Owing to the unique microporous structure and high specific surface area, porous carbon could act as a good carrier for functional materials. In this paper, polyacrylonitrile (PAN)-based porous carbon materials (PPC-0.6-600, PPC-0.8-600, PPC-0.6-800 and PPC-0.8-800) were prepared by heating KOH at 600°C and 800 o C for the removal of Cr(VI) from aqueous solution. The adsorbent was characterized by the techniques of Fourier transform infrared spectroscopy (FT-IR), elementary analysis, scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and N 2 adsorption techniques. The results showed that the adsorption capacity increased with decreasing pH value of the initial solution. The adsorption capacity of Cr(VI) on PPC-0.8-800 was much greater than that on other materials, and maximum adsorption capacity were calculated to be 374.90 mg g −1 . Moreover, PPC-0.8-800 had superior recyclability for the removal of Cr(VI) from wastewater, about 82% of its initial adsorption capacity was retained even after five cycles. The result of kinetic simulation showed that the adsorption of Cr(VI) on the PAN-based porous carbon could be described by pseudo-second-order kinetics. The adsorption process was the ionic interaction between protonated amine groups of PPC and HCrO 4 - ions.

scholarly journals β-Cyclodextrin Modified Poly(Acrylonitrule-co-Acrylic Acid) Hydrogel for Thorium(IV) Adsorption

Polymers ◽  
2017 ◽  
Vol 9 (6) ◽  
pp. 201 ◽  
Author(s):  
Guojian Duan ◽  
Qiangqiang Zhong ◽  
Lei Bi ◽  
Liu Yang ◽  
Tonghuan Liu ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Contact Time ◽  
Ph Value ◽  
Water System ◽  
Maximum Adsorption Capacity ◽  
Practical Application ◽  
X Ray Diffraction ◽  
Liquid Ratio ◽  
X Ray ◽  
Solid Liquid

In this report, the β-CD(AN-co-AA) hydrogel was used to remove the thorium(IV) [Th(IV)] from the water system, and the new adsorbent was characterized through Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The influences of contact time, pH value, ionic strength, solid-liquid ratio, initial Th(IV) concentration, and temperature on Th(IV) adsorption onto the functional hydrogel were researched. The results showed that the experimental data followed the Langmuir isotherm and the maximum adsorption capacity (qmax) for Th(IV) was 692 mg/g at pH 2.95, which approached the calculated (qe) 682 mg/g. The desorption capacity of Th(IV) in different HNO3 concentrations ranging from 0.005 to 0.5 M was also studied, and the percentage of the maximum desorption was 86.85% in the condition of 0.09 M HNO3. The selectivity of β-CD(AN-co-AA) hydrogel was also be studied, the results indicated that this material retained the good adsorption capacity to Th(IV) even when the Ca2+, Mg2+, or Pb2+ existed in the system. The findings indicate that β-CD(AN-co-AA) can be used as a new candidate for the enrichment and separation of Th(IV), or its analogue actinides, from large-volume solution in practical application.

scholarly journals Selenate Adsorption from Water Using the Hydrous Iron Oxide-Impregnated Hybrid Polymer

Metals ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1630
Author(s):  
Vesna Marjanovic ◽  
Aleksandra Peric-Grujic ◽  
Mirjana Ristic ◽  
Aleksandar Marinkovic ◽  
Radmila Markovic ◽  
...  
Keyword(s):  
Iron Oxide ◽  
Adsorption Capacity ◽  
Ph Value ◽  
Xrd Analysis ◽  
Maximum Adsorption Capacity ◽  
Solution Ph ◽  
Adsorbent Regeneration ◽  
Desorption Efficiency ◽  
Hydrous Iron Oxide ◽  
The Cross

Hybrid adsorbent, based on the cross-linked copolymer impregnated with hydrous iron oxide, was applied for the first time for Se(VI) adsorption from water. The influence of the initial solution pH, selenate concentration and contact time to adsorption capacity was investigated. Adsorbent regeneration was explored using a full factorial experimental design in order to optimize the volume, initial pH value and concentration of the applied NaCl solution as a reagent. Equilibrium state was described using the Langmuir model, while kinetics fitted the pseudo-first order. The maximum adsorption capacity was found to be 28.8 mg/g. Desorption efficiency increased up to 70%, and became statistically significant with the reagent concentration and pH increase, while the applied solution volume was found to be insignificant in the investigated range. Based on the results obtained, pH influence to the adsorption capacity, desorption efficiency, Fourier transform infrared (FTIR) and X-ray diffraction (XRD) analysis of loaded adsorbent, it was concluded that the outer- and inner-sphere complexation are mechanisms responsible for Se(VI) separation from water. In addition to the experiments with synthetic solutions, the adsorbent performances in drinking water samples were explored, showing the purification efficiency up to 25%, depending on the initial Se(VI) concentration and water pH. Determined sorption capacity of the cross-linked copolymer impregnated with hydrous iron oxide and its ability for regeneration, candidate this material for further research, as a promising anionic species sorbent.

Sign in / Sign up

Export Citation Format

Share Document