Synthesis of Kapok (Ceiba pentandra) Carbon Sponges for Recovery of Oil and Organic Solvents

2021 ◽  
Vol 880 ◽  
pp. 127-132
Author(s):  
Wayne Christian P. Datiles ◽  
Sellina M. Sy ◽  
Mary Donnabelle L. Balela
Keyword(s):  
Oil Spills ◽  
High Surface ◽  
High Surface Area ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Sem Images ◽  
Water Contact ◽  
Cellulosic Fibers ◽  
Kapok Fibers ◽  
Increasing Temperature

Extensive processes and costly precursors for the fabrication of existing sorbents for oil spills urges to look for more renewable sorbent sources. In this work, hollow, tubular, cellulosic fibers (kapok, Ceibapentandra) were successfully converted to carbon sponges by pyrolysis at increasing temperature and time. Fourier Transform Infrared (FTIR) spectroscopy confirmed the complete carbonization of the kapok fibers at 800 °C. Scanning Electron Microscope (SEM) images revealed that the carbonized kapok fibers maintained their original tubular structures, suggesting high surface area. Water contact angle measurement showed improved hydrophobicity, with a maximum value of about 135°. The carbonized fibers were able to hold selected organic and oil solvents ranging from 16-20 times the weight of the fibers. The fiber pyrolyzed at 400 °C for 0.5 h showed the highest sorption capacity at 45.56 g/g for palm oil, almost matching that of raw kapok.

scholarly journals Effect of Kenaf MCC composition on Thin Film Composite membrane for NaCI Rejection

2019 ◽  
Vol 258 ◽  
pp. 04003
Author(s):  
Azman Ismail ◽  
Ramlah Mohd Tajuddin ◽  
Hamizah Mohktar ◽  
Ahmad Fauzi Ismail
Keyword(s):  
Thin Film ◽  
Interfacial Polymerization ◽  
Pure Water ◽  
Water Flux ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Sem Images ◽  
Water Contact ◽  
Membrane Performance ◽  
Pure Water Flux

A modified thin film PSf-MCC reverse osmosis membrane was prepared by interfacial polymerization between aqueous MPD and TMC as the organic monomer. Aim of this study is to determine the effect of MCC in membrane formulation and fabrication. The surface and cross section morphology of TFC PSF/MCC membrane shows MCC particle which able to improve hydrophilicity of the membrane. The SEM images showed dense and porous structure of the MCC incorporated membranes. In addition, the water contact angle measurement also confirmed the increased hydrophilicity of the modified membranes. The effect of MCC on membrane matric influence the membrane performance in terms of NaCl rejection and pure water flux. Results showed that TFC PSf/MCC membrane shows NaCl rejection up to 98.9% compared with TFC PSf membrane. TFC PSf/MCC membrane also showed the highest pure water flux which is 3.712 Lm2/hr compare with TFC PSF membrane which is 3.606 Lm2/hr. The overall result proved that MCC particle could improve membrane hydrophilicity hence, increased pure water flux and salt rejection.

scholarly journals Superhydrophobic functionalized cellulosic paper by copper hydroxide nanorods for oils purification

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ahmed S. Belal ◽  
Jehan El Nady ◽  
Azza Shokry ◽  
Shaker Ebrahim ◽  
Moataz Soliman ◽  
...  
Keyword(s):  
Contact Angle ◽  
Filter Paper ◽  
Separation Efficiency ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Absorption Capacity ◽  
Morphological Properties ◽  
Copper Hydroxide ◽  
Immersion Method ◽  
Water Contact

AbstractOily water contamination has been sighted as one of the most global environmental pollution. Herein, copper hydroxide nanorods layer was constructed onto cellulosic filter paper surface cured with polydopamine, Ag nanoparticles, and Cu NPs through immersion method. This work has been aimed to produce a superhydrophobic and superoleophilic cellulosic filter paper. The structure, crystalline, and morphological properties of these modified cellulosic filter paper were investigated. Scanning electron microscope images confirmed that the modified surface was rougher compared with the pristine surface. The contact angle measurement confirmed the hydrophobic nature of these modified surfaces with a water contact angle of 169.7°. The absorption capacity was 8.2 g/g for diesel oil and the separation efficiency was higher than 99%. It was noted that the flux in the case of low viscosity solvent as n-hexane was 9663.5 Lm−2 h−1, while for the viscous oil as diesel was 1452.7 Lm−2 h−1.

Plasma Pre-Treatment of Polyethylene Terephthalate Substrate Influence on the Properties of ZnO Thin Film

2014 ◽  
Vol 895 ◽  
pp. 41-44
Author(s):  
Seiw Yen Tho ◽  
Kamarulazizi Ibrahim
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Polyethylene Terephthalate ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Zno Thin Films ◽  
Zno Thin Film ◽  
Water Contact ◽  
Pre Treatment ◽  
Pet Substrate

In this work, the influences of plasma pre-treatment on polyethylene terephthalate (PET) substrate to the properties of ZnO thin film have been carried out. ZnO thin films were successfully grown on PET substrate by spin coating method. In order to study the effects of plasma pre-treatment, a comparison of treated and untreated condition was employed. Water contact angle measurement had been carried out for PET wettability study prior to ZnO thin film coating. Morphology study of ZnO thin film was performed by scanning probe microscope (SPM). Besides, optical study of the ZnO thin film was done by using UV-vis spectrophotometer. All the measured results show that plasma pre-treatment of PET substrate plays an important role in enhancing the wettability of PET and optical properties of the ZnO thin films. In conclusion, pre-treatment of PET surface is essential to produce higher quality ZnO thin film on this particular substrate in which would pave the way for the integration of future devices.

Preparation of TiO2–SiO2 Hybrid Nanosols Coated Flame-Retardant Polyester Fabric Possessing Dual Contradictory Characteristics of Superhydrophobicity and Self Cleaning Ability

2020 ◽  
Vol 20 (3) ◽  
pp. 1780-1789 ◽  
Author(s):  
Priyanka Katiyar ◽  
Shraddha Mishra ◽  
Anurag Srivastava ◽  
N. Eswara Prasad
Keyword(s):  
Electron Microscopy ◽  
Contact Angle ◽  
Flame Retardant ◽  
Protective Clothing ◽  
Sol Gel ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Water Contact ◽  
Vis Spectroscopy ◽  
Self Cleaning

TiO2, SiO2 and their hybrid nanocoatings are prepared on inherent flame retardant textile substrates from titanium(IV)iso-proproxide (TTIP) and tetraethoxysilane (TEOS) precursors using a sol–gel process followed by hydrothermal treatment. The coated samples are further functionalized by hexadecyltrimethoxysilane (HDTMS) to impart superhydrophobicity. Sample characterization of the nanosols, nanoparticles and coated samples are investigated using, X-ray diffractometer, transmission electron microscopy, scanning electron microscopy, UV-Vis spectroscopy, contact angle measurement. Stain degradation test under mild UV irradiation shows almost 54% degradation of coffee stain within 4 hours measured by Spectrophotometer. UV-Vis Absorption Spectroscopy demonstrates complete degradation of methyl orange colorant within 3 hours. Hybrid nanosol coated and HDTMS modified inherent flame retardant polyester surfaces show apparent water contact angle as ~145°, which is much closer to proximity of superhydrophobic surfaces. Thus, the novelty of present work is, by using sol–gel technique, a bi-functional textile surface has been developed which qualifies the very specific requirements of protective clothing like self-cleaning property (imparted by TiO2 nanoparticles) and superhydrophobicity (imparted by SiO2 nanoparticles and further surface modification by HDTMS), which are entirely contradictory in nature, in a single fabric itself. Thus developed textile surfaces also possess the other attributes of protective clothing like flame retardancy and air permeability.

scholarly journals Application of Waterborne Acrylic and Solvent-Borne Polyester Coatings on Plasma-Treated Fir (Abies alba M.) Wood

Materials ◽  
2022 ◽  
Vol 15 (1) ◽  
pp. 370
Author(s):  
Hadi Gholamiyan ◽  
Behnam Gholampoor ◽  
Reza Hosseinpourpia
Keyword(s):  
Plasma Treatment ◽  
Treated Wood ◽  
Abies Alba ◽  
Untreated Wood ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Accelerated Weathering ◽  
Water Contact ◽  
Before And After ◽  
Carbon Dioxide Co2

This research investigates the effect of plasma treatment with air, nitrogen (N2), and carbon dioxide (CO2) gases on the performance of waterborne (acrylic) and solvent-borne (polyester) coated fir (Abies alba M.) wood samples. The properties of the plasma-coated samples were analyzed before and after exposure to accelerated weathering and compared with those of untreated and solely treated ones. According to pull-off testing, the coating adhesion of the wood samples was considerably improved by plasma treatment, and obvious differences were observed between different plasma gases. The effect was more pronounced after the weathering test. Similar results were obtained for the abrasion resistance of the samples. The water contact angle measurement illustrated more hydrophilic character in the solely plasma-treated wood in comparison with the untreated wood. The application of coatings, however, strongly improved its hydrophobic character. The performances of waterborne and solvent-borne coatings on plasma-treated wood were comparable, although slightly better values were obtained by the waterborne system. Our results exhibit the positive effect of plasma treatment on coating performances and the increased weather resistance of the waterborne and solvent-borne coating systems on plasma-treated wood.

scholarly journals High Loading Capacity and Wear Resistance of Graphene Oxide/Organic Molecule Assembled Multilayer Film

2021 ◽  
Vol 9 ◽  
Author(s):  
Li Chen ◽  
Gang Wu ◽  
Yin Huang ◽  
Changning Bai ◽  
Yuanlie Yu ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
Multilayer Films ◽  
Thickness Measurement ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Film Structure ◽  
Silicon Substrates ◽  
Water Contact ◽  
Macro Scale

Taking advantage of the strong charge interactions between negatively charged graphene oxide (GO) sheets and positively charged poly(diallyldimethylammonium chloride) (PDDA), self-assembled multilayer films of (GO/PDDA)n were created on hydroxylated silicon substrates by alternating electrostatic adsorption of GO and PDDA. The formation and structure of the films were analyzed by means of water contact angle measurement, thickness measurement, atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). Meanwhile, tribological behaviors in micro- and macro- scale were investigated by AFM and a ball-on-plate tribometer, respectively. The results showed that (GO/PDDA)n multilayer films exhibited excellent friction-reducing and anti-wear abilities in both micro- and macro-scale, which was ascribed to the special structure in (GO/PDDA)n multilayer films, namely, a well-stacked GO–GO layered structure and an elastic 3D crystal stack in whole. Such a film structure is suitable for design molecular lubricants for MEMS and other microdevices.

Surface Modification of Ultra-High Molecular Weight Polyethylene with Crosslinked Hyaluronic Acid and its Antiwear Performance

2015 ◽  
Vol 642 ◽  
pp. 94-98
Author(s):  
Chau Chang Chou ◽  
Yu Hsiang Hao ◽  
Fu Yin Hsu
Keyword(s):  
Molecular Weight ◽  
Hyaluronic Acid ◽  
High Molecular Weight ◽  
Incident Light ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Coated Sample ◽  
Infrared Spectrometry ◽  
Water Contact ◽  
Ultra High Molecular Weight

The surface of high-pressure crystallized ultra-high molecular weight polyethylene (UHMWPE) was modified for application as an artificial cartilage material. A UHMWPE surface pretreated by a series of processes, including treatment with O2-plasma and ethylenediamine solution, was coated with hyaluronic acid (HA). After that, adipic acid dihydrazide (AAD) was added to partially crosslink the HA coating in order to enhance its durability. The modified samples were verified by water contact angle measurement and Fourier transform infrared spectrometry. Both HA layers, original and crosslinked, were also quantitatively evaluated by carbohydrate chemistry assay according to the absorbance of the incident light. The tribological performance of the samples was evaluated by a pin-on-disk test rig lubricated by normal saline under an average pressure of 18 MPa and at a sliding speed of 0.03 m/s for 45 h. The wear resistance of the HA-coated UHMWPE specimens promoted by the crosslink process was superior to that of the original HA-coated sample, and that resistance was maintained after immersion in saline solution for one month.

Effect of Plasma-Induced Polymerization on Contact Angle of Paper

2011 ◽  
Vol 396-398 ◽  
pp. 1619-1623
Author(s):  
Zhao Ping Song ◽  
Jun Rong Li ◽  
Hui Ning Xiao
Keyword(s):  
Contact Angle ◽  
Photoelectron Spectroscopy ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Polymer Grafting ◽  
Hydrophobic Property ◽  
Cellulose Fibres ◽  
Water Contact ◽  
X Ray ◽  
Factors Associated

Hydrophobic modification of cellulose fibres was conducted by plasma-induced polymer grafting in an attempt to increase the hydrophobicity of paper. Two hydrophobic monomers, i.e., butyl acrylate (BA) and 2-ethylhexyl acrylate (2-EHA) were grafted on cellulose fibres, induced by atmospheric cold plasma. Various influencing factors associated with the plasma-induced grafting were investigated, including the contact time and reaction temperature with monomers, and the dosage of monomers. Contact-angle measurement, infrared spectrum (IR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscope (SEM) were used to ascertain the occurrence of the grafting. The results showed that the hydrophobic property of the modified paper sheet was improved significantly after the plasma-induced grafting. The water contact angle on the surface of the paper reached up to higher than125°.

scholarly journals Amorphous Mo5O14-Type/Carbon Nanocomposite with Enhanced Electrochemical Capability for Lithium-Ion Batteries

Nanomaterials ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 8 ◽  
Author(s):  
Ahmed M. Hashem ◽  
Ashraf E. Abdel-Ghany ◽  
Rasha S. El-Tawil ◽  
Sylvio Indris ◽  
Helmut Ehrenberg ◽  
...  
Keyword(s):  
Oxygen Deficiency ◽  
High Surface ◽  
High Surface Area ◽  
Lithium Ion ◽  
Carbon Matrix ◽  
X Ray Diffraction ◽  
Sem Images ◽  
Thermal Gravimetry ◽  
Type C ◽  
Carbon Nanocomposite

An amorphous MomO3m−1/carbon nanocomposite (m ≈ 5) is fabricated from a citrate–gel precursor heated at moderate temperature (500 °C) in inert (argon) atmosphere. The as-prepared Mo5O14-type/C material is compared to α-MoO3 synthesized from the same precursor in air. The morphology and microstructure of the as-prepared samples are characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and Raman scattering (RS) spectroscopy. Thermal gravimetry and elemental analysis indicate the presence of 25.8 ± 0.2% of carbon in the composite. The SEM images show that Mo5O14 is immersed inside a honeycomb-like carbon matrix providing high surface area. The RS spectrum of Mo5O14/C demonstrates an oxygen deficiency in the molybdenum oxide and the presence of a partially graphitized carbon. Outstanding improvement in electrochemical performance is obtained for the Mo5O14 encapsulated by carbon in comparison with the carbon-free MoO3.

Sign in / Sign up

Export Citation Format

Share Document