Homogenization Modes Effect on Mechanical Properties and Corrosive Characteristics of the Rolled Products from Al-Mg (1570) Aluminum Alloy with Addition of Scandium and Zirconium

2022 ◽  
Vol 1049 ◽  
pp. 102-107
Author(s):  
Aleksandr A. Ragazin ◽  
Vasiliy V. Yashin ◽  
Ilya A. Latushkin ◽  
Evgenii V. Aryshesnkii ◽  
Fedor V. Grechnikov
Keyword(s):  
Mechanical Properties ◽  
Annealing Temperature ◽  
Strength Properties ◽  
Commercial Production ◽  
Scanning Microscope ◽  
Interdendritic Segregation ◽  
Electron Scanning Microscope ◽  
Production Practices ◽  
Increasing Temperature ◽  
Resistance Improvement

Objective of the study: study of various homogenization modes effects on mechanical and corrosive properties of rolled sheets from Al-Mg system alloy 1570 with additions of zirconium and scandium transition metals. The sheets were produced in laboratory conditions from the ingot, cast in production DC mold based on the commercial production practices and treatment modes. 4 homogenization modes, 2 tempers H12 and H321, and several modes of stabilization annealing in the temperature range from 240 °C to 325 °C have been reviewed. The samples have been comprehensively examined using optic and electron scanning microscope, mechanical properties were achieved by break test in compliance with ISO 6892-1, corrosion was examined using ASTM G66 and G67 standards. The curve of 1570 alloy sheets softening as the function of annealing temperature was constructed. It was demonstrated that the increasing temperature effect during homogenization leads to strength properties decrease and corrosion resistance improvement due to interdendritic segregation elimination. Among analyzed homogenization modes, 360 - 380 °C - 6 h mode is established as the most practical, and the sheets. produced without stabilization annealing, occurred to be the most resistant to exfoliation corrosion. The sheets, subjected to annealing at 260 °C - 2 h, show no traces of layer corrosion, but have pit corrosion locations rated as «PC» based on ASTM G-66 classification, such rating is unacceptable for the manufacture of products for use in the marine environment.

Effect of annealing temperature on microstructure and mechanical properties of a Ti–18Zr–12.5Nb–2Sn (at.%) alloy

2018 ◽  
Vol 11 (05) ◽  
pp. 1850033 ◽  
Author(s):  
Shuanglei Li ◽  
Tae-Hyun Nam
Keyword(s):  
Mechanical Properties ◽  
Annealing Temperature ◽  
Fracture Strain ◽  
Rolled Plate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Recovery Strain ◽  
Microstructure And Mechanical Properties ◽  
Cold Rolled ◽  
Increasing Temperature

In this study, the effect of annealing temperature on microstructure and mechanical properties of a Ti–18Zr–12.5Nb–2Sn (at.%) alloy was investigated by using optical microscopy (OM), X-ray diffraction (XRD) measurement and tensile test. The cold-rolled plate was annealed at temperatures between 773[Formula: see text]K and 1173[Formula: see text]K. Recrystallization occurred in the specimen annealed at 873[Formula: see text]K. Grain size increased from 8[Formula: see text][Formula: see text]m to 80[Formula: see text][Formula: see text]m with increasing temperature from 873[Formula: see text]K to 1173[Formula: see text]K. The ultimate tensile strength decreased from 1590[Formula: see text]MPa to 806[Formula: see text]MPa with increasing annealing temperature from 773[Formula: see text]K to 973[Formula: see text]K, and then showed similar value in the specimens annealed at temperatures from 973[Formula: see text]K to 1173[Formula: see text]K. The fracture strain increased from 3.8% to 41.0% with increasing annealing temperature from 773[Formula: see text]K to 1173[Formula: see text]K due to the recovery and recrystallization. The recovery strain increased with increasing of annealing temperature attributed to the evolution of recrystallization texture.

scholarly journals Structural and Mechanical Properties of Ti–Co Alloys Treated by High Pressure Torsion

Materials ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 426 ◽  
Author(s):  
Boris Straumal ◽  
Anna Korneva ◽  
Askar Kilmametov ◽  
Lidia Lityńska-Dobrzyńska ◽  
Alena Gornakova ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Pressure ◽  
Annealing Temperature ◽  
High Pressure Torsion ◽  
Pure Titanium ◽  
Eutectoid Transformation ◽  
Ω Phase ◽  
Preliminary Annealing ◽  
Increasing Temperature ◽  
Co Alloys

The microstructure and properties of titanium-based alloys can be tailored using severe plastic deformation. The structure and microhardness of Ti–4 wt.% Co alloy have been studied after preliminary annealing and following high pressure torsion (HPT). The Ti–4 wt.% Co alloy has been annealed at 400, 500, and 600 °C, i.e., below the temperature of eutectoid transformation in the Ti–4 wt.% Co system. The amount of Co dissolved in α-Ti increased with increasing annealing temperature. HPT led to the transformation of α-Ti in ω-Ti. After HPT, the amount of ω-phase in the sample annealed at 400 °C was about 80­85%, i.e., higher than in pure titanium (about 40%). However, with increasing temperature of pre-annealing, the portion of ω-phase decreased (60–65% at 500 °C and about 5% at 600 °C). The microhardness of all investigated samples increased with increasing temperature of pre-annealing.

Effect of nickel on formation of transition layer during liquid-phase aluminizing of titanium

2020 ◽  
pp. 313-317
Author(s):  
A.I. Kovtunov ◽  
Yu.Yu. Khokhlov ◽  
S.V. Myamin
Keyword(s):  
Mechanical Properties ◽  
Liquid Phase ◽  
Intermetallic Layer ◽  
Reaction Diffusion ◽  
Strength Properties ◽  
Effect Of Temperature ◽  
Nickel Concentration ◽  
Aluminum Melt ◽  
Titanium Aluminum ◽  
Titanium Foam

Titanium—aluminum, titanium—foam aluminum composites and bimetals obtained by liquid-phase methods, are increasingly used in industry. At the liquid-phase methods as result of the reaction diffusion of titanium and aluminum is formed transitional intermetallic layer at the phase boundary of the composite, which reduces the mechanical properties of titanium and composite. To reduce the growth rate of the intermetallic layer between the layers of the composite and increase its mechanical properties, it is proposed to alloy aluminum melt with nickel. The studies of the interaction of titanium and molten aluminum alloyed with nickel made it possible to establish the effect of temperature and aluminizing time on the thickness, chemical and phase compositions of the transition intermetallic layer. The tests showed the effect of the temperature of the aluminum melt, the nickel concentration on the strength properties of titanium—aluminum bimetal.

scholarly journals Microstructure and Mechanical Properties of Novel Quasibinary Al-Cu-Yb and Al-Cu-Gd Alloys

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 476
Author(s):  
Sayed Amer ◽  
Ruslan Barkov ◽  
Andrey Pozdniakov
Keyword(s):  
Mechanical Properties ◽  
Tensile Properties ◽  
Mechanism Of Action ◽  
Annealing Temperature ◽  
Eutectic Reaction ◽  
Solidification Process ◽  
Annealed State ◽  
Microstructure And Mechanical Properties ◽  
Cold Rolled ◽  
Hot Rolled

Microstructure of Al-Cu-Yb and Al-Cu-Gd alloys at casting, hot-rolled -cold-rolled and annealed state were observed; the effect of annealing on the microstructure was studied, as were the mechanical properties and forming properties of the alloys, and the mechanism of action was explored. Analysis of the solidification process showed that the primary Al solidification is followed by the eutectic reaction. The second Al8Cu4Yb and Al8Cu4Gd phases play an important role as recrystallization inhibitor. The Al3Yb or (Al, Cu)17Yb2 phase inclusions are present in the Al-Cu-Yb alloy at the boundary between the eutectic and aluminum dendrites. The recrystallization starting temperature of the alloys is in the range of 250–350 °C after rolling with previous quenching at 590 and 605 °C for Al-Cu-Yb and Al-Cu-Gd, respectively. The hardness and tensile properties of Al-Cu-Yb and Al-Cu-Gd as-rolled alloys are reduced by increasing the annealing temperature and time. The as-rolled alloys have high mechanical properties: YS = 303 MPa, UTS = 327 MPa and El. = 3.2% for Al-Cu-Yb alloy, while YS = 290 MPa, UTS = 315 MPa and El. = 2.1% for Al-Cu-Gd alloy.

scholarly journals Comparative Analysis of Shear Strength Parallel to Fiber of Different Local Bamboo Species in the Philippines

2021 ◽  
Vol 13 (15) ◽  
pp. 8164
Author(s):  
Brian E. Bautista ◽  
Lessandro E. O. Garciano ◽  
Luis F. Lopez
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Comparative Analysis ◽  
Strength Properties ◽  
The Philippines ◽  
Bamboo Species ◽  
Test Protocol ◽  
Future Design ◽  
Average Shear Strength ◽  
Bambusa Vulgaris

There are limited published studies related to the mechanical properties of bamboo species in the Philippines. In this study, the shear strength properties of some economically viable bamboo species in the Philippines were properly characterized based on 220 shear test results. The rationales of selecting this mechanical property are the following: (1) Shear strength, parallel to the fiber, has the highest variability among the mechanical properties; and (2) Shear is one of the governing forces on joint connections, and such connections are the points of failure on bamboo structures when subjected to extreme loading conditions. ISO 22157-1 (2017) test protocol for shear was used for all tests. The results showed that Bambusa blumeana has the highest average shear strength, followed by Gigantochloa apus, Dendrocalamus asper, Bambusa philippinensis, and Bambusa vulgaris. However, comparative analysis, using One-way ANOVA, showed that shear strength values among these bamboo species have significant differences statistically. A linear regression model is also established to estimate the shear strength of bamboo from the physical properties. Characteristic shear strength is also determined using ISO 12122-1 (2014) for future design reference.

scholarly journals The Extrusion and SPS of Zirconium–Copper Powders and Studies of Selected Mechanical Properties

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3560
Author(s):  
Tomasz Skrzekut ◽  
Grzegorz Boczkal ◽  
Adam Zwoliński ◽  
Piotr Noga ◽  
Lucyna Jaworska ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Intermetallic Compounds ◽  
Room Temperature ◽  
Intermetallic Phase ◽  
Extrusion Process ◽  
Strength Properties ◽  
Plasma Sintering ◽  
Copper Powders ◽  
Spark Plasma ◽  
Zirconium Copper

Zr-2.5Cu and Zr-10Cu powder mixtures were consolidated in the extrusion process and using the spark plasma sintering technique. In these studies, material tests were carried out in the fields of phase composition, microstructure, hardness and tensile strength for Zr-Cu materials at room temperature (RT) and 400 °C. Fractography analysis of materials at room temperature and 400 °C was carried out. The research took into account the anisotropy of the materials obtained in the extrusion process. For the nonequilibrium SPS process, ZrCu2 and Cu10Zr7 intermetallic compounds formed in the material at sintering temperature. Extruded materials were composed mainly of α-Zr and ZrCu2. The presence of intermetallic compounds affected the reduction in the strength properties of the tested materials. The highest strength value of 205 MPa was obtained for the extruded Zr-2.5Cu, for which the samples were cut in the direction of extrusion. For materials with 10 wt.% copper, more participation of the intermetallic phase was formed, which lowered the mechanical properties of the obtained materials. In addition to brittle intermetallic phases, the materials were characterized by residual porosity, which also reduced the strength properties.

scholarly journals Effect of PWHT on the Microstructure and Mechanical Properties of Friction Stir Welded DP780 Steel

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1097
Author(s):  
Umer Masood Chaudry ◽  
Seung-Chang Han ◽  
Fathia Alkelae ◽  
Tea-Sung Jun
Keyword(s):  
Mechanical Properties ◽  
Annealing Temperature ◽  
Tensile Elongation ◽  
Image Correlation ◽  
Frictional Heat ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties ◽  
Dp780 Steel

In the present study, the effect of post-weld heat treatment (PWHT) on the microstructure and mechanical properties of friction stir welded (FSW) DP780 steel sheets was investigated. FSW was carried out at a constant tool rotation speed of 400 rpm and different welding speeds (200 mm/min and 400 min/min). A defect free weld was witnessed for both of the welding conditions. The mutual effect of severe plastic deformation and frictional heat generation by pin rotation during the FSW process resulted in grain refinement due to dynamic recrystallization in the stir zone (SZ) and thermo-mechanically affected zone (TMAZ). Lower tensile elongation and higher yield and ultimate tensile strengths were recorded for welded-samples as compared to the base material (BM) DP780 steel. The joints were subsequently annealed at various temperatures at 450–650 °C for 1 h. At higher annealing temperature, the work hardening rate of joints gradually decreased and subsequently failed in the softened heat-affected zone (HAZ) during the uniaxial tensile test. Reduction in yield strength and tensile strength was found in all PWHT conditions, though improvement in elongation was achieved by annealing at 550 °C. The digital image correlation analysis showed that an inhomogeneous strain distribution occurred in the FSWed samples, and the strain was particularly highly localized in the advancing side of interface zone. The nanoindentation measurements covering the FSWed joint were consistent with an increase of the annealing temperature. The various grains size in the BM, TMAZ, and SZ is the main factor monitoring the hardness distribution in these zones and the observed discrepancies in mechanical properties.

scholarly journals Cell mechanical properties of human breast carcinoma cells depend on temperature

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Christian Aermes ◽  
Alexander Hayn ◽  
Tony Fischer ◽  
Claudia Tanja Mierke
Keyword(s):  
Mechanical Properties ◽  
Power Law ◽  
Cell Mechanics ◽  
Cell Types ◽  
Creep Response ◽  
Temperature Range ◽  
Myosin Filaments ◽  
Cell Mechanical Properties ◽  
Increasing Temperature ◽  
Mcf 7

AbstractThe knowledge of cell mechanics is required to understand cellular processes and functions, such as the movement of cells, and the development of tissue engineering in cancer therapy. Cell mechanical properties depend on a variety of factors, such as cellular environments, and may also rely on external factors, such as the ambient temperature. The impact of temperature on cell mechanics is not clearly understood. To explore the effect of temperature on cell mechanics, we employed magnetic tweezers to apply a force of 1 nN to 4.5 µm superparamagnetic beads. The beads were coated with fibronectin and coupled to human epithelial breast cancer cells, in particular MCF-7 and MDA-MB-231 cells. Cells were measured in a temperature range between 25 and 45 °C. The creep response of both cell types followed a weak power law. At all temperatures, the MDA-MB-231 cells were pronouncedly softer compared to the MCF-7 cells, whereas their fluidity was increased. However, with increasing temperature, the cells became significantly softer and more fluid. Since mechanical properties are manifested in the cell’s cytoskeletal structure and the paramagnetic beads are coupled through cell surface receptors linked to cytoskeletal structures, such as actin and myosin filaments as well as microtubules, the cells were probed with pharmacological drugs impacting the actin filament polymerization, such as Latrunculin A, the myosin filaments, such as Blebbistatin, and the microtubules, such as Demecolcine, during the magnetic tweezer measurements in the specific temperature range. Irrespective of pharmacological interventions, the creep response of cells followed a weak power law at all temperatures. Inhibition of the actin polymerization resulted in increased softness in both cell types and decreased fluidity exclusively in MDA-MB-231 cells. Blebbistatin had an effect on the compliance of MDA-MB-231 cells at lower temperatures, which was minor on the compliance MCF-7 cells. Microtubule inhibition affected the fluidity of MCF-7 cells but did not have a significant effect on the compliance of MCF-7 and MDA-MB-231 cells. In summary, with increasing temperature, the cells became significant softer with specific differences between the investigated drugs and cell lines.

scholarly journals Overview of HSS Steel Grades Development and Study of Reheating Condition Effects on Austenite Grain Size Changes

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 1988
Author(s):  
Tibor Kvackaj ◽  
Jana Bidulská ◽  
Róbert Bidulský
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
High Strength Steel ◽  
Single Phase ◽  
Hsla Steel ◽  
High Strength ◽  
Strength Properties ◽  
Austenite Grain Size ◽  
Austenite Grain ◽  
Steel Grades

This review paper concerns the development of the chemical compositions and controlled processes of rolling and cooling steels to increase their mechanical properties and reduce weight and production costs. The paper analyzes the basic differences among high-strength steel (HSS), advanced high-strength steel (AHSS) and ultra-high-strength steel (UHSS) depending on differences in their final microstructural components, chemical composition, alloying elements and strengthening contributions to determine strength and mechanical properties. HSS is characterized by a final single-phase structure with reduced perlite content, while AHSS has a final structure of two-phase to multiphase. UHSS is characterized by a single-phase or multiphase structure. The yield strength of the steels have the following value intervals: HSS, 180–550 MPa; AHSS, 260–900 MPa; UHSS, 600–960 MPa. In addition to strength properties, the ductility of these steel grades is also an important parameter. AHSS steel has the best ductility, followed by HSS and UHSS. Within the HSS steel group, high-strength low-alloy (HSLA) steel represents a special subgroup characterized by the use of microalloying elements for special strength and plastic properties. An important parameter determining the strength properties of these steels is the grain-size diameter of the final structure, which depends on the processing conditions of the previous austenitic structure. The influence of reheating temperatures (TReh) and the holding time at the reheating temperature (tReh) of C–Mn–Nb–V HSLA steel was investigated in detail. Mathematical equations describing changes in the diameter of austenite grain size (dγ), depending on reheating temperature and holding time, were derived by the authors. The coordinates of the point where normal grain growth turned abnormal was determined. These coordinates for testing steel are the reheating conditions TReh = 1060 °C, tReh = 1800 s at the diameter of austenite grain size dγ = 100 μm.

scholarly journals Influence of Alumina Nanofibers Sintered by the Spark Plasma Method on Nickel Mechanical Properties

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 548 ◽  
Author(s):  
Leonid Agureev ◽  
Valeriy Kostikov ◽  
Zhanna Eremeeva ◽  
Svetlana Savushkina ◽  
Boris Ivanov ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Strength Properties ◽  
Alumina Nanoparticles ◽  
Metal Powders ◽  
Wide Range ◽  
The Matrix ◽  
Spark Plasma ◽  
Average Size

The article presents the study of alumina nanoparticles’ (nanofibers) concentration effect on the strength properties of pure nickel. The samples were obtained by spark plasma sintering of previously mechanically activated metal powders. The dependence of the grain size and the relative density of compacts on the number of nanofibers was investigated. It was found that with an increase in the concentration of nanofibers, the average size of the matrix particles decreased. The effects of the nanoparticle concentration (0.01–0.1 wt.%) on the elastic modulus and tensile strength were determined for materials at 25 °C, 400 °C, and 750 °C. It was shown that with an increase in the concentration of nanofibers, a 10–40% increase in the elastic modulus and ultimate tensile strength occurred. A comparison of the mechanical properties of nickel in a wide range of temperatures, obtained in this work with materials made by various technologies, is carried out. A description of nanofibers’ mechanisms of influence on the structure and mechanical properties of nickel is given. The possible impact of impurity phases on the properties of nickel is estimated. The tendency of changes in the mechanical properties of nickel, depending on the concentration of nanofibers, is shown.

Sign in / Sign up

Export Citation Format

Share Document