A tribo-oxidation abrasive wear model to quantify the wear rate of a cobalt-based alloy subjected to fretting in low-to-medium temperature conditions

2018 ◽  
Vol 125 ◽  
pp. 128-140 ◽  
Author(s):  
Alixe Dréano ◽  
Siegfried Fouvry ◽  
Gaylord Guillonneau
Keyword(s):  
Wear Rate ◽  
Abrasive Wear ◽  
Wear Model ◽  
Medium Temperature ◽  
Temperature Conditions

scholarly journals Prediction of Abrasive and Impact Wear Due to Multi-Shaped Particles in a Centrifugal Pump via CFD-DEM Coupling Method

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2391
Author(s):  
Cheng Tang ◽  
You-Chao Yang ◽  
Peng-Zhan Liu ◽  
Youn-Jea Kim
Keyword(s):  
Wear Rate ◽  
Abrasive Wear ◽  
Centrifugal Pump ◽  
Coupling Method ◽  
Particle Model ◽  
Equivalent Diameter ◽  
Impact Wear ◽  
Centrifugal Pumps ◽  
Wear Model ◽  
The Impact

Since solid particles suspended in the fluid can cause wear in centrifugal pumps, intensive attention has been focused on the numerical prediction for the wear of flow parts in centrifugal pumps. However, most numerical studies have focused on only one wear model and a sphere particle model. The impact of particle shape on the wear of flow parts in centrifugal pumps is under-studied, particularly considering abrasive and impact wear simultaneously. In this work, the Computational Fluid Dynamics (CFD)-Discrete Element Method (DEM) coupling method with an abrasive and impact wear prediction model was adopted to study the wear characteristics of a centrifugal pump. Moreover, four regular polyhedron particles and a sphere particle with the same equivalent diameter but different sphericity were mainly analyzed. The results demonstrate that more particles move closer to the blade pressure side in the impeller passage, and particles tend to cluster in specific areas within the volute as sphericity increases. The volute suffers the principal wear erosion no matter what the shapes of particles and wear model are. Both the impact and abrasive wear within the impeller occur primarily on the blade leading edge. The pump’s overall impact wear rate decreases first and then increases with particle sphericity rising, while the pump’s overall abrasive wear rate grows steadily.

Increasing in wear resistance of excavating machine elements

2020 ◽  
pp. 306-308
Author(s):  
V.S. Bochkov
Keyword(s):  
Wear Resistance ◽  
Wear Rate ◽  
Abrasive Wear ◽  
Thermomechanical Treatment ◽  
Cold Work ◽  
Hadfield Steel ◽  
Outer Side ◽  
Viii And Ix ◽  
Machine Elements ◽  
The Impact

The relevance of the search for solutions to increase the wear resistance of bucket teeth of excavating machine type front shovel is analyzed. The reasons for the wear of the teeth are considered. It is determined that when excavating machines work for rocks of VIII and IX categories, impact-abrasive wear of the inner side of the teeth and abrasive external wear occurs. It is proved that the cold-work hardening of Hadfield steel (the teeth material), which occurs during the excavating machine teeth work in the rocks of VIII and IX categories, reduces the impact-abrasive wear rate on the inner side of the teeth and does not affect the abrasive wear of the outer. The methods for thermomechanical treatment of the outer side of the excavating machine tooth is proposed. It can increase the wear resistance of Hadfield steel (110G13L) up to 1.7 times and lead to the self-sharpening effect of the tooth due to equalization of the wear rate of the outer and inner parts of the tooth. The efficiency factor of thermomechanical treatment to reduce the of abrasive wear rate of Hadfield steel is experimentally proved.

scholarly journals Simulation and Experimental Study on Wear of U-Shaped Rings of Power Connection Fittings under Strong Wind Environment

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 735
Author(s):  
Songchen Wang ◽  
Xianchen Yang ◽  
Xinmei Li ◽  
Cheng Chai ◽  
Gen Wang ◽  
...  
Keyword(s):  
Abrasive Wear ◽  
Adhesive Wear ◽  
Surface Hardness ◽  
Wear Depth ◽  
Strong Wind ◽  
Wear Model ◽  
Wind Environment ◽  
Simulation Results ◽  
Oxidation Wear ◽  
Good Agreement

The objective of this study was to investigate the wear characteristics of the U-shaped rings of power connection fittings, and to construct a wear failure prediction model of U-shaped rings in strong wind environments. First, the wear evolution and failure mechanism of U-shaped rings with different wear loads were studied by using a swinging wear tester. Then, based on the Archard wear model, the U-shaped ring wear was dynamically simulated in ABAQUS, via the Umeshmotion subroutine. The results indicated that the wear load has an important effect on the wear of the U-shaped ring. As the wear load increases, the surface hardness decreases, while plastic deformation layers increase. Furthermore, the wear mechanism transforms from adhesive wear, slight abrasive wear, and slight oxidation wear, to serious adhesive wear, abrasive wear, and oxidation wear with the increase of wear load. As plastic flow progresses, the dislocation density in ferrite increases, leading to dislocation plugs and cementite fractures. The simulation results of wear depth were in good agreement with the test value of, with an error of 1.56%.

Machining and Wear of High-Alumina Ceramics for Structural Applications

2009 ◽  
Vol 409 ◽  
pp. 137-144 ◽  
Author(s):  
Stojana Veskovic-Bukudur ◽  
Tanja Leban ◽  
Milan Ambrozic ◽  
Tomaž Kosmač
Keyword(s):  
Grain Size ◽  
Wear Rate ◽  
Abrasive Wear ◽  
Direct Relationship ◽  
Bending Strength ◽  
High Alumina ◽  
Alumina Ceramics ◽  
Large Area ◽  
Structural Applications ◽  
Worn Surfaces

The wear resistances of four standard-grade high-alumina ceramics were evaluated and related to their machining ability. Three of the material grades contained 96% of alumina and 4% of either calcium silicate, or magnesium silicate, or manganese titanate in the starting-powder composition. The nominal alumina content in the fourth material was 99.7%. The specimens were fabricated using a low-pressure injection-molding forming technique, followed by thermal de-binding and sintering. After sintering the four materials differ significantly in their grain size, bending strength and Vickers hardness. No direct relationship between the microstructural parameters and the mechanical properties was found, but there was a grain-size dependence of the surface finish after grinding under industrial conditions. The two silicate-containing ceramics exhibited considerably higher wear resistances than the two silicate-free ceramics, but no direct relationship between the abrasive wear rate during grinding and the cutting time was observed. The cutting ability represents a valuable material characteristic for industrial practice, but it should not be directly used for predicting the wear rate during grinding. Quantitative differences in the cutting time and abrasive wear rate were manifested in the different topographies of the worn surfaces. Cutting resulted in relatively large area fractions of plastically deformed surfaces, whereas pullouts dominated the worn surfaces after grinding.

Failure of Rubber by Abrasion

1985 ◽  
Vol 58 (3) ◽  
pp. 653-661 ◽  
Author(s):  
Carl T. R. Pulford
Keyword(s):  
Abrasive Wear ◽  
Physical Model ◽  
Abrasion Resistance ◽  
Short Review ◽  
Wear Model ◽  
Fracture Properties ◽  
Tire Wear ◽  
Physical Principles

Abstract This short review presents the landmark discoveries and ideas in rubber abrasion that have brought the field to where it is today. First, the important features of rubber abrasion are reviewed as background for a physical model for the abrasion of rubber. The model, due to Thomas, is described in detail, since it clearly shows the connection between the failure of rubber by abrasive wear and the appropriate rubber fracture properties. The implications of the model for improved abrasion resistance are also discussed. Then, physical principles are applied to the failure of rubber by abrasion in actual products, such as tires. The tire wear model of Schallamach and Turner is described, together with its success in explaining several features of tire wear.

Investigation of the Wear Behavior of AA6082 Against Different Counterparts

2021 ◽  
Author(s):  
Safiye İpek Ayvaz ◽  
Mehmet Ayvaz
Keyword(s):  
Wear Resistance ◽  
Aluminum Alloy ◽  
Wear Rate ◽  
Abrasive Wear ◽  
Wear Behavior ◽  
Specific Wear Rate ◽  
Pin On Disk ◽  
Disk Method ◽  
Sliding Distance ◽  
Oxidation Wear

In this study, the effect of different counterparts on the wear resistance of AA6082 aluminum alloy was investigated. In tests using pin-on-disk method, 6 mm diameter Al2O3, 100Cr6 and WC-6Co balls were used as counterparts. The tests were carried out using 500 m sliding distance and 5N load. The lowest specific wear rate was measured as 7.58x10-4 mm3/Nm in WC-6Co / AA6082 couple, and the highest value was measured as 9.71x10-4 mm3/Nm in 100Cr6/AA6082 couple. In the Al2O3/AA6082 couple, the specific wear rate of the AA6082-T6 sample was determined as 8.23x10-4 mm3/Nm.While it was observed that the dominant wear type in the 100Cr6/AA6082 pair was abrasive wear, oxidation wear and oxide tribofilm were detected in the WC-6Co/AA6082 and Al2O3/AA6082 couple besides the abrasive wear.

Wear Performance of GCr15 Friction Pairs with Effect of Initial Radial Micro-Grooves

2019 ◽  
Vol 11 (1) ◽  
pp. 56-61
Author(s):  
Wei Yuan ◽  
Shengkai Mei ◽  
Song Li ◽  
Zhiwen Wang ◽  
Jie Yu ◽  
...  
Keyword(s):  
Wear Rate ◽  
Abrasive Wear ◽  
Electrical Discharge Machining ◽  
Friction Pair ◽  
Wear Volume ◽  
Fatigue Wear ◽  
Wear Performance ◽  
Wear Process ◽  
Groove Test ◽  
On Line

Background: Grooves may inevitably occur on the surface of the friction pair caused by severe wear or residual stress, which will play an important role on the reliability of machine parts during operation. Objective: The effect of the micro-grooves perpendicular to sliding direction on the wear performance of the friction pairs should be studied. Method: Micro-grooves can be machined on discs of friction pairs using electrical discharge machining. On-line visual ferrograph method was used to monitor the wear process to research the wear rate changing characteristic. Profilemeter and metallurgical microscope were used to observe the wear scars. Results: Comparing to the non-groove test, i) in one-groove test, wear volume and rate were approximate the same, and the wear scar was smooth, ii) when the grooves more than 4, the test running-in stage will be obviously prolonged, particularly for the test with 8 grooves on the disc, the duration of running-in stage is 4 times than that without grooves on specimen, and the wear rate and volume increase significantly, and then decrease with fluctuation, iii) the abrasive wear can be avoid with the debris stagnating in the groove, however, fatigue wear will significantly emerge. Conclusion: Abrasive wear can be avoided and smooth running-in surfaces can be obtained with proper amount of initial radial micro-grooves.

Fabrication and characterization of TiB2-reinforced functionally graded aluminum matrix material

2020 ◽  
Vol 72 (10) ◽  
pp. 1147-1152
Author(s):  
Ömer Savaş
Keyword(s):  
Wear Rate ◽  
Abrasive Wear ◽  
Peer Review ◽  
Centrifugal Force ◽  
Matrix Material ◽  
Aluminum Matrix ◽  
Functionally Graded ◽  
Aluminum Matrix Composites ◽  
Content Type

Purpose This study aims to investigate the production and abrasive wear rate of functionally graded TiB2/Al composites. TiB2 particles have been spontaneously formed in liquid matrix using in situ technique. The properties of composites such as hardness, abrasive wear rate and microstructure have been examined. Design/methodology/approach In situ TiB2 reinforcement phase was synthesized by using a liquid Al–Ti–B system. A semi-solid composite (Al(l)-TiB2(s)) prepared at 900°C was solidified under a centrifugal force to both grade functionally and give the final shape to materials. Abrasive wear test of materials was conducted using the pin-on-disk method at room temperature. The wear tests were carried out with two different loads of 1 Newton (N) and 2 N, a sliding velocity of 3.5 m s−1 and a sliding distance of 75 m. Findings This research provided the following findings; TiB2 particles can be successfully synthesized with in situ reaction technique in molten aluminum. It was determined that abrasive wear rate increases with increasing load and decreases with increasing TiB2 reinforcement content within matrix. Originality/value In previous studies, there have been many trials on the in situ production of TiB2-reinforced aluminum matrix composites. However, there are few studies on production of in situ TiB2-reinforced aluminum matrix functionally graded materials. At the same time, there is no study that the properties of composite, such as hardness and abrasive wear rate, are examined together according to centrifugal force. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-12-2019-0538/

Sign in / Sign up

Export Citation Format

Share Document