Entry Flow in Straight and Curved Channels With Slender Channel Approximations

1977 ◽  
Vol 99 (4) ◽  
pp. 666-673 ◽  
Author(s):  
F. G. Blottner

The slender channel equations for laminar flow are solved downstream of the entrance of curved channels of variable height. The singularities at the entrance are removed with coordinate transformations which stretch the boundary layer and shrink the core flow. Initial conditions at the entrance are obtained from the governing equations with only the streamwise velocity specified. A modified box scheme is used to develop a finite-difference method which allows the derivatives of the dependent variables across the channel to be discontinuous at the interface between the boundary layer and core flow. Numerical results are presented for several channel geometries and entry conditions.

2018 ◽  
Vol 18 (1) ◽  
pp. 3-48
Author(s):  
LMBC Campos ◽  
C Legendre

In this study, the propagation of waves in a two-dimensional parallel-sided nozzle is considered allowing for the combination of: (a) distinct impedances of the upper and lower walls; (b) upper and lower boundary layers with different thicknesses with linear shear velocity profiles matched to a uniform core flow; and (c) a uniform cross-flow as a bias flow out of one and into the other porous acoustic liner. The model involves an “acoustic triple deck” consisting of third-order non-sinusoidal non-plane acoustic-shear waves in the upper and lower boundary layers coupled to convected plane sinusoidal acoustic waves in the uniform core flow. The acoustic modes are determined from a dispersion relation corresponding to the vanishing of an 8 × 8 matrix determinant, and the waveforms are combinations of two acoustic and two sets of three acoustic-shear waves. The eigenvalues are calculated and the waveforms are plotted for a wide range of values of the four parameters of the problem, namely: (i/ii) the core and bias flow Mach numbers; (iii) the impedances at the two walls; and (iv) the thicknesses of the two boundary layers relative to each other and the core flow. It is shown that all three main physical phenomena considered in this model can have a significant effect on the wave field: (c) a bias or cross-flow even with small Mach number [Formula: see text] relative to the mean flow Mach number [Formula: see text] can modify the waveforms; (b) the possibly dissimilar impedances of the lined walls can absorb (or amplify) waves more or less depending on the reactance and inductance; (a) the exchange of the wave energy with the shear flow is also important, since for the same stream velocity, a thin boundary layer has higher vorticity, and lower vorticity corresponds to a thicker boundary layer. The combination of all these three effects (a–c) leads to a large set of different waveforms in the duct that are plotted for a wide range of the parameters (i–iv) of the problem.


Author(s):  
Ersin Sayar

Heat transfer in an oscillating water column in the transition regime of pool boiling to bubbly flow is investigated experimentally and theoretically. Forced oscillations are applied to water via a frequency controlled dc motor and a piston-cylinder device. Heat transfer is from the electrically heated inner surface to the reciprocating flow. The heat transfer in the oscillating fluid column is altered by using stainless steel scrap metal layers (made off open-cell discrete cells) which produces a porous medium within the system. The effective heat transfer mechanism is enhanced and it is due to the hydrodynamic mixing of the boundary layer and the core flow. In oscillating flow, the hydrodynamic lag between the core flow and the boundary layer flow is somehow significant. At low actuation frequencies and at low heat fluxes, heat transfer is restricted in the single phase flows. The transition regime of pool boiling to bubbly flow is proposed to be a remedy to the stated limitation. The contribution by the pool boiling on heat transfer appears to be the dominant mechanism for the selected low oscillation amplitudes and frequencies. Accordingly the regime is a transition from pool boiling to bubbly flow. Nucleate-bubbly flow boiling in oscillating flow is also investigated using a simplified thermodynamic analysis. According to the experimental results, bubbles induce highly efficient heat transfer mechanisms. Experimental study proved that the heater surface temperature is the dominant parameter affecting heat transfer. At greater actuation frequencies saturated nucleate pool boiling ceases to exist. Actuation frequency becomes important in that circumstances. The present investigation has possible applications in moderate sized wicked heat pipes, boilers, compact heat exchangers and steam generators.


1976 ◽  
Vol 98 (1) ◽  
pp. 58-68 ◽  
Author(s):  
A. K. M. F. Hussain ◽  
V. Ramjee

The performance characteristics of four different axisymmetric contraction shapes with the same contraction ratio are experimentally investigated for incompressible flow. The pre- and postcontraction mean and turbulent velocity profiles and spectra, and the variation of the mean and turbulent velocities along the axis as a function of local contraction ratio and axial length are presented in this paper. The results show that all the nozzles are of essentially equal effectiveness as far as the core flow in the exit plane is concerned. But the mean and turbulence characteristics of the exit boundary layer, the upstream influence of the contraction, and the departure from equipartition within the nozzle vary significantly with the contraction shape. The data demonstrate the inadequacy of the Batchelor-Proudman-Ribner-Tucker theory in predicting the effect of a contraction on the turbulence structure. These data are of interest in wind tunnel and nozzle design, and in boundary layer prediction.


Author(s):  
Kenneth L. Suder

A detailed experimental investigation to understand and quantify the development of blockage in the flow field of a transonic, axial flow compressor rotor (NASA Rotor 37) has been undertaken. Detailed laser anemometer measurements were acquired upstream, within, and downstream of a transonic, axial compressor rotor operating at 100%, 85%, 80%, and 60% of design speed which provided inlet relative Mach numbers at the blade tip of 1.48, 1.26, 1.18, and 0.89 respectively. The impact of the shock on the blockage development, pertaining to both the shock / boundary layer interactions and the shock / tip clearance flow interactions, is discussed. The results indicate that for this rotor the blockage in the endwall region is 2–3 times that of the core flow region, and the blockage in the core flow region more than doubles when the shock strength is sufficient to separate the suction surface boundary layer.


2015 ◽  
Vol 783 ◽  
pp. 379-411 ◽  
Author(s):  
I. Marusic ◽  
K. A. Chauhan ◽  
V. Kulandaivelu ◽  
N. Hutchins

In this paper we study the spatial evolution of zero-pressure-gradient (ZPG) turbulent boundary layers from their origin to a canonical high-Reynolds-number state. A prime motivation is to better understand under what conditions reliable scaling behaviour comparisons can be made between different experimental studies at matched local Reynolds numbers. This is achieved here through detailed streamwise velocity measurements using hot wires in the large University of Melbourne wind tunnel. By keeping the unit Reynolds number constant, the flow conditioning, contraction and trip can be considered unaltered for a given boundary layer’s development and hence its evolution can be studied in isolation from the influence of inflow conditions by moving to different streamwise locations. Careful attention was given to the experimental design in order to make comparisons between flows with three different trips while keeping all other parameters nominally constant, including keeping the measurement sensor size nominally fixed in viscous wall units. The three trips consist of a standard trip and two deliberately ‘over-tripped’ cases, where the initial boundary layers are over-stimulated with additional large-scale energy. Comparisons of the mean flow, normal Reynolds stress, spectra and higher-order turbulence statistics reveal that the effects of the trip are seen to be significant, with the remnants of the ‘over-tripped’ conditions persisting at least until streamwise stations corresponding to $Re_{x}=1.7\times 10^{7}$ and $x=O(2000)$ trip heights are reached (which is specific to the trips used here), at which position the non-canonical boundary layers exhibit a weak memory of their initial conditions at the largest scales $O(10{\it\delta})$, where ${\it\delta}$ is the boundary layer thickness. At closer streamwise stations, no one-to-one correspondence is observed between the local Reynolds numbers ($Re_{{\it\tau}}$, $Re_{{\it\theta}}$ or $Re_{x}$ etc.), and these differences are likely to be the cause of disparities between previous studies where a given Reynolds number is matched but without account of the trip conditions and the actual evolution of the boundary layer. In previous literature such variations have commonly been referred to as low-Reynolds-number effects, while here we show that it is more likely that these differences are due to an evolution effect resulting from the initial conditions set up by the trip and/or the initial inflow conditions. Generally, the mean velocity profiles were found to approach a constant wake parameter ${\it\Pi}$ as the three boundary layers developed along the test section, and agreement of the mean flow parameters was found to coincide with the location where other statistics also converged, including higher-order moments up to tenth order. This result therefore implies that it may be sufficient to document the mean flow parameters alone in order to ascertain whether the ZPG flow, as described by the streamwise velocity statistics, has reached a canonical state, and a computational approach is outlined to do this. The computational scheme is shown to agree well with available experimental data.


2020 ◽  
Vol 72 (1) ◽  
Author(s):  
Masaki Matsushima

AbstractThe electrical conductivity of the Earth’s core is an important physical parameter that controls the core dynamics and the thermal evolution of the Earth. In this study, the effect of core electrical conductivity on core surface flow models is investigated. Core surface flow is derived from a geomagnetic field model on the presumption that a viscous boundary layer forms at the core–mantle boundary. Inside the boundary layer, where the viscous force plays an important role in force balance, temporal variations of the magnetic field are caused by magnetic diffusion as well as motional induction. Below the boundary layer, where core flow is assumed to be in tangentially geostrophic balance or tangentially magnetostrophic balance, contributions of magnetic diffusion to temporal variation of the magnetic field are neglected. Under the constraint that the core flow is tangentially geostrophic beneath the boundary layer, the core electrical conductivity in the range from $${10}^{5} ~\mathrm{S}~{\mathrm{m}}^{-1}$$ 10 5 S m - 1 to $${10}^{7}~ \mathrm{S}~{\mathrm{m}}^{-1}$$ 10 7 S m - 1 has less significant effect on the core flow. Under the constraint that the core flow is tangentially magnetostrophic beneath the boundary layer, the influence of electrical conductivity on the core flow models can be clearly recognized; the magnitude of the mean toroidal flow does not increase or decrease, but that of the mean poloidal flow increases with an increase in core electrical conductivity. This difference arises from the Lorentz force, which can be stronger than the Coriolis force, for higher electrical conductivity, since the Lorentz force is proportional to the electrical conductivity. In other words, the Elsasser number, which represents the ratio of the Lorentz force to the Coriolis force, has an influence on the difference. The result implies that the ratio of toroidal to poloidal flow magnitudes has been changing in accordance with secular changes of rotation rate of the Earth and of core electrical conductivity due to a decrease in core temperature throughout the thermal evolution of the Earth.


Author(s):  
David J. Charlesworth ◽  
Mehrdad Zangeneh

A cell centred, finite volume, pressure correction method for unstructured grids is presented that facilitates the use of high order convective modelling. This is achieved through the use of a least squares technique to calculate first and second partial derivatives of the governing equations dependent variables. These derivatives are then used to construct both second and third order convective models that are bounded, accurate and stable. As an initial test of the effectiveness of these models calculated results are compared with standard laminar flow problems in both two and three dimensions.


2001 ◽  
Vol 124 (1) ◽  
pp. 152-159 ◽  
Author(s):  
T. Korakianitis ◽  
P. Papagiannidis ◽  
N. E. Vlachopoulos

The unsteady flow in stator–rotor interactions affects the structural integrity, aerodynamic performance of the stages, and blade-surface heat transfer. Numerous viscous and inviscid computer programs are used for the prediction of unsteady flows in two-dimensional and three-dimensional stator–rotor interactions. The relative effects of the various components of flow unsteadiness on heat transfer are under investigation. In this paper it is shown that for subsonic cases, the reduced frequency parameter for boundary-layer calculations is about two orders of magnitude smaller than the reduced frequency parameter for the core flow. This means that for typical stator–rotor interactions, the unsteady flow terms are needed to resolve the location of disturbances in the core flow, but in many cases the instantaneous disturbances can be input in steady-flow boundary-layer computations to evaluate boundary-layer effects in a quasi-steady approximation. This hypothesis is tested by comparing computations with experimental data on a turbine rotor for which there are extensive experimental heat transfer data available in the open literature. An unsteady compressible inviscid two-dimensional computer program is used to predict the propagation of the upstream stator disturbances into the downstream rotor passages. The viscous wake (velocity defect) and potential flow (pressure fluctuation) perturbations from the upstream stator are modeled at the computational rotor–inlet boundary. The effects of these interactions on the unsteady rotor flow result in computed instantaneous velocity and pressure fields. The period of the rotor unsteadiness is one stator pitch. The instantaneous velocity fields on the rotor surfaces are input in a steady-flow differential boundary-layer program, which is used to compute the instantaneous heat transfer rate on the rotor blades. The results of these quasi-steady heat-transfer computations are compared with the results of unsteady heat transfer experiments and with the results of previous unsteady heat transfer computations. The unsteady flow fields explain the unsteady amplitudes and phases of the increases and decreases in instantaneous heat transfer rate. It is concluded that the present method is accurate for quantitative predictions of unsteady heat transfer in subsonic turbine flows.


Author(s):  
Philippe Versailles ◽  
Wajid Ali Chishty ◽  
Huu Duc Vo

Dry low emissions premixed combustion systems have the ability to give larger NOx emissions reduction in comparison to diffusion type of combustors. However, these systems are prone to flashback because the fuel and oxidizers are mixed upstream of the combustion chamber. This is particularly true for premixed systems burning high-reactivity fuels due to their higher flame speed. Flashback is undesirable in gas turbines because it leads to overheating and failure of fuel nozzles and premixing sections. Recently, a novel application of Plasma Actuation through non-thermal Dielectric Barrier Discharge has been shown to significantly delay flashback in the core flow along the axis of the premixer. Building on this successful endeavour, efforts were directed to prove the effectiveness of the control method in situations where flashback was triggered in the boundary layer. Results show that the current application delays the occurrence of flashback in the boundary layer of the premixer to higher equivalence ratios. Improvements in the combustor operability margin of 10 to 14% when burning natural gas-air mixtures, and of about 3.5% when replacing the fuel by an equimolar mixture of natural gas and hydrogen, were achieved. It was found that the proposed application of plasma actuation is even more efficient in preventing flashback in the boundary layer than in the core flow.


Water ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 3515
Author(s):  
Hachem Kassem ◽  
Charlotte E. L. Thompson ◽  
Carl L. Amos ◽  
Ian H. Townend ◽  
David Todd ◽  
...  

Collinear wave-current shear interactions are often assumed to be the same for currents following or opposing the direction of regular wave propagation; with momentum and mass exchanges restricted to the thin oscillating boundary layer (zero-flux condition) and enhanced but equal wave-averaged bed shear stresses. To examine these assumptions, a prototype-scale experiment investigated the nature of turbulent exchanges in flows with currents aligned to, and opposing, wave propagation over a mobile sandy bed. Estimated mean and maximum stresses from measurements above the bed exceeded predictions by models of bed shear stress subscribing to the assumptions above, suggesting the combined boundary layer is larger than predicted by theory. The core flow experiences upward turbulent fluxes in aligned flows, coupled with sediment entrainment by vortex shedding at flow reversal, whilst downward fluxes of eddies generated by the core flow, and strong adverse shear can enhance near-bed mass transport, in opposing currents. Current-aligned coherent structures contribute significantly to the stress and energy dissipation, and display characteristics of wall-attached eddies formed by the pairing of counter-rotating vortices. These preliminary findings suggest a notable difference in wave-following and wave-opposing wave-current interactions, and highlight the need to account for intermittent momentum-exchanges in predicting stress, boundary layer thickness and sediment transport.


Sign in / Sign up

Export Citation Format

Share Document