scholarly journals Elastic Properties of Natural Sea Surface Films Incorporated with Solid Dust Particles: Model Baltic Sea Studies

2012 ◽  
Vol 2012 ◽  
pp. 1-14 ◽  
Author(s):  
Adriana Z. Mazurek ◽  
Stanisław J. Pogorzelski
Keyword(s):  
Baltic Sea ◽  
Surface Film ◽  
Contact Angles ◽  
Solid Particles ◽  
Sea Surface ◽  
Dust Particles ◽  
Surface Films ◽  
Particle Removal ◽  
Water Contact ◽  
Composite Surface

Floating dust-originated solid particles at air-water interfaces will interact with one another and disturb the smoothness of such a composite surface affecting its dilational elasticity. To quantify the effect, surface pressure (Π) versus film area (A) isotherm, and stress-relaxation (Π-time) measurements were performed for monoparticulate layers of the model hydrophobic material (of μm-diameter and differentiated hydrophobicity corresponding to the water contact angles (CA) ranging from 60 to 140°) deposited at surfaces of surfactant-containing original seawater and were studied with a Langmuir trough system. The composite surface dilational modulus predicted from the theoretical approach, in which natural dust load signatures (particle number flux, daily deposition rate, and diameter spectra) originated from in situ field studies performed along Baltic Sea near-shore line stations, agreed well with the direct experimentally derived data. The presence of seawater surfactants affected wettability of the solid material which was evaluated with different CA techniques applicable to powdered samples. Surface energetics of the particle-subphase interactions was expressed in terms of the particle removal energy, contact cross-sectional areas, collapse energies, and so forth. The hydrophobic particles incorporation at a sea surface film structure increased the elasticity modulus by a factor K (1.29–1.58). The particle-covered seawater revealed a viscoelastic behavior with the characteristic relaxation times ranging from 2.6 to 68.5 sec.

Environmentally Conscious Gas Mixtures for Magnesium Melt Protection

2006 ◽  
Vol 510-511 ◽  
pp. 806-809 ◽  
Author(s):  
Won Ha ◽  
Jeong Il Youn ◽  
Young Jig Kim
Keyword(s):  
Surface Film ◽  
Chemical Properties ◽  
Fluorine Content ◽  
Surface Films ◽  
Environmentally Conscious ◽  
Composite Surface ◽  
Gas Concentration ◽  
Porous Magnesium ◽  
Magnesium Melt ◽  
And Chemical Properties

The candidate gases for the replacement of SF6 in magnesium melt protection were reviewed from the viewpoint of environmental effects, melt protection properties, and chemical properties. The surface films formed under fluorine bearing gases were analyzed by using XPS. The XPS results revealed that the surface films consist of MgO and MgF2. The fluorine content of the surface film increases with increasing gas concentration and exposure time. The Pilling- Bedworth ratio (PBR) of MgO was 0.73, and the porous magnesium oxide could not cover the whole melt surface. PBR of MgF2 was 1.29, and the surface film which contains MgF2 could cover a lager area of the melt surface. This higher PBR of composite surface film prevented further oxidation and evaporation of magnesium.

Surface Films on Zircaloy-2 Samples Cracked in Neutral Aqueous NaCl by Stress Corrosion

1973 ◽  
Vol 31 ◽  
pp. 46-47
Author(s):  
R.A. Ploc
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Film Thickness ◽  
Stress Corrosion ◽  
Zirconium Dioxide ◽  
Surface Film ◽  
Surface Films ◽  
Continuous Layer ◽  
Transmission Electron ◽  
Product Film

Samples of low-nickel Zircaloy-2 (material MLI-788-see(1)), when anodically polarized in neutral 5 wt% NaCl solutions, were found to be susceptible to pitting and stress corrosion cracking. The SEM revealed that pitting of stressed samples was occurring below a 2000Å thick surface film which behaved differently from normal zirconium dioxide in that it did not display interference colours. Since the initial film thickness was approximately 65Å, attempts were made to examine the product film by transmission electron microscopy to deduce composition and how the corrosion environment could penetrate the continuous layer.

scholarly journals The Effect of Hydroxyl on the Superhydrophobicity of Dodecyl Methacrylate (LMA) Coated Fabrics through Simple Dipping-Plasma Crosslinked Method

Coatings ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1263
Author(s):  
Liyun Xu ◽  
Yu Zhang ◽  
Ying Guo ◽  
Ruiyun Zhang ◽  
Jianjun Shi ◽  
...  
Keyword(s):  
Thermoplastic Polyurethane ◽  
Hydrophobic Effect ◽  
Surface Hydrophobicity ◽  
Contact Angles ◽  
Binding Property ◽  
Interesting Phenomenon ◽  
Water Contact ◽  
Capacitively Coupled ◽  
Pet Fabric ◽  
Dodecyl Methacrylate

In order to obtain stable superhydrophobicity, suitable hydrophobic treatment agents should be selected according to different material properties. In this paper, cotton and poly(ethylene terephthalate) (PET) fabrics were respectively coated with dodecyl methacrylate (LMA) via argon combined capacitively coupled plasma (CCP), and the surface hydrophobicity and durability of the treated cotton and polyester fabrics are also discussed. An interesting phenomenon happened, whereby the LMA-coated cotton fabric (Cotton-g-LMA) had better water repelling and mechanical durability properties than LMA-coated PET fabric (PET-g-LMA), and LMA-coated hydroxyl-grafted PET fabrics (PET fabrics were successively coated with polyethylene glycol (PEG) and LMA, PET-g-PEG & LMA) had a similar performance to cotton fabrics. The water contact angles of Cotton-g-LMA, PET-g-LMA and PET-g-PEG & LMA were 156°, 153° and 155°, respectively, and after 45 washing cycles or 1000 rubbing cycles, the corresponding water contact angles decreased to 145°, 88°, 134° and 146°, 127° and 143°, respectively. Additionally, thermoplastic polyurethane (TPU) and polyamides-6 (PA6) fabrics all exhibited the same properties as the PET fabric. Therefore, the grafting of hydroxyl can improve the hydrophobic effect of LMA coating and the binding property between LMA and fabrics effectively, without changing the wearing comfort.

Investigation of the different particle size dust releases from rigid filter candles during pulse-jet cleaning

2021 ◽  
pp. 095440622110179
Author(s):  
Xin Luan ◽  
Zhongli Ji ◽  
Longfei Liu ◽  
Ruifeng Wang
Keyword(s):  
Particle Size ◽  
Critical Role ◽  
Operating Conditions ◽  
Solid Particles ◽  
Dust Particles ◽  
Cleaning Efficiency ◽  
Term Operation ◽  
Cleaning Performance ◽  
Experimental Apparatus ◽  
Pulse Jet

Rigid filters made of ceramic or metal are widely used to remove solid particles from hot gases at temperature above 260 °C in the petrochemical and coal industries. Pulse-jet cleaning of fine dust from rigid filter candles plays a critical role in the long-term operation of these filters. In this study, an experimental apparatus was fabricated to investigate the behavior of a 2050 mm filter candle, which included monitoring the variation of pressure dynamic characteristics over time and observing the release of dust layers that allowed an analysis of the cleaning performance of ISO 12103-1 test dusts with different particle size distributions. These results showed the release behavior of these dusts could be divided into five stages: radial expansion, axial crack, flaky release, irregular disruption and secondary deposition. The cleaning performance of smaller sized dust particles was less efficient as compared with larger sized dust particles under the same operating conditions primarily because large, flaky-shaped dust aggregates formed during the first three stages were easily broken into smaller, dispersed fragments during irregular disruption that forced more particles back to the filter surface during secondary deposition. Also, a “low-pressure and long-pulse width” cleaning method improved the cleaning efficiency of the A1 ultrafine test dust from 81.4% to 95.9%.

scholarly journals Polypropylene/Lignin/POSS Nanocomposites: Thermal and Wettability Properties, Application in Water Remediation

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3950
Author(s):  
Abeer Alassod ◽  
Syed Rashedul Islam ◽  
Mina Shahriari Khalaji ◽  
Rogers Tusiime ◽  
Wanzhen Huang ◽  
...  
Keyword(s):  
Organic Liquid ◽  
Contact Angles ◽  
Water Remediation ◽  
Scanning Calorimetry ◽  
Water Contact ◽  
Thermally Induced ◽  
Dsc Measurements ◽  
Infrared Measurement ◽  
Oligomeric Silsesquioxane ◽  
Tga And Dsc

Compositing is an interesting strategy that has always been employed to introduce or enhance desired functionalities in material systems. In this paper, sponges containing polypropylene, lignin, and octavinyl-polyhedral oligomeric silsesquioxane (OV-POSS) were successfully prepared via an easy and elegant strategy called thermally induced phase separation (TIPS). To fully explore the behaviour of different components of prepared sponges, properties were characterized by a thermogravimetric analyser (TGA), differential scanning calorimetry (DSC), Fourier transform infrared measurement (FTIR), and scanning electron microscopy (SEM). Furthermore, wettability properties toward an organic liquid and oil were investigated. The FTIR analysis confirmed the chemical modification of the components. TGA and DSC measurements revealed thermal stability was much better with an increase in OV-POSS content. OV-POSS modified sponges exhibited ultra-hydrophobicity and high oleophilicity with water contact angles of more than 125°. The SEM revealed that POSS molecules acted as a support for reduced surface roughness. Moreover, OV-POSS-based blend sponges showed higher sorption capacities compared with other blend sponges without OV-POSS. The new blend sponges demonstrated a potential for use as sorbent engineering materials in water remediation.

scholarly journals Physico-Chemical Characterization and Antimicrobial Properties of Hybrid Film Based on Saponite and Phloxine B

Molecules ◽  
2021 ◽  
Vol 26 (2) ◽  
pp. 325
Author(s):  
Nitin Chandra teja Dadi ◽  
Matúš Dohál ◽  
Veronika Medvecká ◽  
Juraj Bujdák ◽  
Kamila Koči ◽  
...  
Keyword(s):  
Hybrid Film ◽  
Antimicrobial Properties ◽  
Chemical Characterization ◽  
Layered Silicate ◽  
Contact Angles ◽  
Exchange Capacity ◽  
Resistant Bacteria ◽  
Hybrid Films ◽  
Water Contact ◽  
Physico Chemical

This research was aimed at the preparation of a hybrid film based on a layered silicate saponite (Sap) with the immobilized photosensitizer phloxine B (PhB). Sap was selected because of its high cation exchange capacity, ability to exfoliate into nanolayers, and to modify different surfaces. The X-ray diffraction of the films confirmed the intercalation of both the surfactant and PhB molecules in the Sap film. The photosensitizer retained its photoactivity in the hybrid films, as shown by fluorescence spectra measurements. The water contact angles and the measurement of surface free energy demonstrated the hydrophilic nature of the hybrid films. Antimicrobial effectiveness, assessed by the photodynamic inactivation on hybrid films, was tested against a standard strain and against methicillin-resistant bacteria of Staphylococcus aureus (MRSA). One group of samples was irradiated (green LED light; 2.5 h) and compared to nonirradiated ones. S. aureus strains manifested a reduction in growth from 1-log10 to over 3-log10 compared to the control samples with Sap only, and defects in S. aureus cells were proven by scanning electron microscopy. The results proved the optimal photo-physical properties and anti-MRSA potential of this newly designed hybrid system that reflects recent progress in the modification of surfaces for various medical applications.

scholarly journals Bonding of Selected Hardwoods with PVAc Adhesive

2020 ◽  
Vol 11 (1) ◽  
pp. 67
Author(s):  
Ján Iždinský ◽  
Ladislav Reinprecht ◽  
Ján Sedliačik ◽  
Jozef Kúdela ◽  
Viera Kučerová
Keyword(s):  
Adhesion Strength ◽  
Cold Water ◽  
Ph Value ◽  
Water Extract ◽  
Solid Wood ◽  
Contact Angles ◽  
Water Contact ◽  
Ph Values ◽  
Positive Tendency ◽  
The Impact

The bonding of wood with assembly adhesives is crucial for manufacturing wood composites, such as solid wood panels, glulam, furniture parts, and sport and musical instruments. This work investigates 13 hardwoods—bangkirai, beech, black locust, bubinga, ipé, iroko, maçaranduba, meranti, oak, palisander, sapelli, wengé and zebrano—and analyzes the impact of their selected structural and physical characteristics (e.g., the density, cold water extract, pH value, roughness, and wettability) on the adhesion strength with the polyvinyl acetate (PVAc) adhesive Multibond SK8. The adhesion strength of the bonded hardwoods, determined by the standard EN 205, ranged in the dry state from 9.5 MPa to 17.2 MPa, from 0.6 MPa to 2.6 MPa in the wet state, and from 8.5 MPa to 19.2 MPa in the reconditioned state. The adhesion strength in the dry state of the bonded hardwoods was not influenced by their cold water extracts, pH values, or roughness parallel with the grain. On the contrary, the adhesion strength was significantly with positive tendency influenced by their higher densities, lower roughness parameters perpendicular to the grain, and lower water contact angles.

scholarly journals Remote Sensing Supported Sea Surface pCO2 Estimation and Variable Analysis in the Baltic Sea

2021 ◽  
Vol 13 (2) ◽  
pp. 259
Author(s):  
Shuping Zhang ◽  
Anna Rutgersson ◽  
Petra Philipson ◽  
Marcus B. Wallin
Keyword(s):  
Remote Sensing ◽  
Baltic Sea ◽  
Mean Squared Error ◽  
Numerical Models ◽  
Mixed Layer Depth ◽  
Sea Surface ◽  
The Baltic Sea ◽  
Chl A ◽  
Marginal Seas ◽  
The Baltic

Marginal seas are a dynamic and still to large extent uncertain component of the global carbon cycle. The large temporal and spatial variations of sea-surface partial pressure of carbon dioxide (pCO2) in these areas are driven by multiple complex mechanisms. In this study, we analyzed the variable importance for the sea surface pCO2 estimation in the Baltic Sea and derived monthly pCO2 maps for the marginal sea during the period of July 2002–October 2011. We used variables obtained from remote sensing images and numerical models. The random forest algorithm was employed to construct regression models for pCO2 estimation and produce the importance of different input variables. The study found that photosynthetically available radiation (PAR) was the most important variable for the pCO2 estimation across the entire Baltic Sea, followed by sea surface temperature (SST), absorption of colored dissolved organic matter (aCDOM), and mixed layer depth (MLD). Interestingly, Chlorophyll-a concentration (Chl-a) and the diffuse attenuation coefficient for downwelling irradiance at 490 nm (Kd_490nm) showed relatively low importance for the pCO2 estimation. This was mainly attributed to the high correlation of Chl-a and Kd_490nm to other pCO2-relevant variables (e.g., aCDOM), particularly in the summer months. In addition, the variables’ importance for pCO2 estimation varied between seasons and sub-basins. For example, the importance of aCDOM were large in the Gulf of Finland but marginal in other sub-basins. The model for pCO2 estimate in the entire Baltic Sea explained 63% of the variation and had a root of mean squared error (RMSE) of 47.8 µatm. The pCO2 maps derived with this model displayed realistic seasonal variations and spatial features of sea surface pCO2 in the Baltic Sea. The spatially and seasonally varying variables’ importance for the pCO2 estimation shed light on the heterogeneities in the biogeochemical and physical processes driving the carbon cycling in the Baltic Sea and can serve as an important basis for future pCO2 estimation in marginal seas using remote sensing techniques. The pCO2 maps derived in this study provided a robust benchmark for understanding the spatiotemporal patterns of CO2 air-sea exchange in the Baltic Sea.

scholarly journals Fabrication of Superhydrophobic Ti–6Al–4V Surfaces with Single-Scale Micotextures by using Two-Step Laser Irradiation and Silanization

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3816
Author(s):  
Haidong He ◽  
Risheng Hua ◽  
Xuan Li ◽  
Chunju Wang ◽  
Xuezhong Ning ◽  
...  
Keyword(s):  
Laser Irradiation ◽  
Laser Fluence ◽  
Rolling Direction ◽  
Contact Angles ◽  
Second Step ◽  
Water Contact ◽  
Single Scale ◽  
The Common ◽  
The Rich ◽  
Hierarchical Multiscale

Laser irradiation is a popular method to produce microtextures on metal surfaces. However, the common laser-produced microtextures were hierarchical (multiscale), which may limit their applicability. In this paper, a method of two-step laser irradiation, combining first-step strong ablation and sequentially second-step gentle ablation, was presented to produce micron-rough surface with single-scale microtextures. The effect of laser fluence on the Ti–6Al–4V surface morphology and wettability were investigated in detail. The morphology results revealed that the microtextures produced using this method gradually evolved from multiscale to single-scale meanwhile from microprotrusions to microholes with increasing the second-step laser fluence from 0.0 to 2.4 J/cm2. The wettability and EDS/XPS results indicated that attributing to the rich TiO2 content and micron roughness produced by laser irradiation, all the two-step laser-irradiated surfaces exhibited superhydrophilicity. In addition, after silanization, all these superhydrophilic surfaces immediately turned to be superhydrophobic with close water contact angles of 155–162°. However, due to the absence of nanotextures, the water-rolling angle on the superhydrophobic surfaces with single-scale microtextures distinctly larger than those with multiscale ones. Finally, using the two-step laser-irradiation method and assisted with silanization, multifunctional superhydrophobic Ti–6Al–4V surfaces were achieved, including self-cleaning, guiding of the water-rolling direction and anisotropic water-rolling angles (like the rice-leaf), etc.

scholarly journals P4VP Modified Zwitterionic Polymer for the Preparation of Antifouling Functionalized Surfaces

Nanomaterials ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 706 ◽  
Author(s):  
Chaoqun Wu ◽  
Yudan Zhou ◽  
Haitao Wang ◽  
Jianhua Hu
Keyword(s):  
Photoelectron Spectroscopy ◽  
Cell Attachment ◽  
Raft Polymerization ◽  
Polymer Brush ◽  
Contact Angles ◽  
Polymerization Process ◽  
Water Contact ◽  
Zwitterionic Polymers ◽  
Ito Glass ◽  
Zwitterionic Polymer

Zwitterionic polymers are suitable for replacing poly(ethylene glycol) (PEG) polymers because of their better antifouling properties, but zwitterionic polymers have poor mechanical properties, strong water absorption, and their homopolymers should not be used directly. To solve these problems, a reversible-addition fragmentation chain transfer (RAFT) polymerization process was used to prepare copolymers comprised of zwitterionic side chains that were attached to an ITO glass substrate using spin-casting. The presence of 4-vinylpyridine (4VP) and zwitterion chains on these polymer-coated ITO surfaces was confirmed using 1H NMR, FTIR, and GPC analyses, with successful surface functionalization confirmed using water contact angle, X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM) studies. Changes in water contact angles and C/O ratios (XPS) analysis demonstrated that the functionalization of these polymers with β-propiolactone resulted in hydrophilic mixed 4VP/zwitterionic polymers. Protein adsorption and cell attachment assays were used to optimize the ratio of the zwitterionic component to maximize the antifouling properties of the polymer brush surface. This work demonstrated that the antifouling surface coatings could be readily prepared using a “P4VP-modified” method, that is, the functionality of P4VP to modify the prepared zwitterionic polymer. We believe these materials are likely to be useful for the preparation of biomaterials for biosensing and diagnostic applications.

Sign in / Sign up

Export Citation Format

Share Document