scholarly journals Crack Detectability in Vertical Axis Cooling Pumps During Operation

2004 ◽  
Vol 10 (2) ◽  
pp. 121-133 ◽  
Author(s):  
N. Bachschmid ◽  
P. Pennacchi ◽  
E. Tanzi ◽  
P. Verrier ◽  
F. Hasnaoui ◽  
...  
Keyword(s):  
Cold Water ◽  
Water Pressure ◽  
Vertical Axis ◽  
Cyclic Stress ◽  
Hot Water ◽  
Rotating Shaft ◽  
Machine Condition Monitoring ◽  
Pump Shaft ◽  
Condition Monitoring System ◽  
Thermal Striping

The problem which is faced in this article is the analysis of the effects of a transverse propagating crack on the vibrational behavior of a vertical axis cooling pump. The crack is assumed to develop in a section between the impeller and a seal, preventing the hot water to flow upwards along the rotor shaft. The pressurized seal is fed with an injection of cold water, and crack initiation may be due to a thermal striping phenomenon. Afterwards, crack growth could be driven by a combination of thermal and mechanical loads, causing alternate cyclic stress in the shaft. Cracking instances of this type have been reported worldwide in several machines of similar design. In this article, the fact is emphasized that the crack behavior is likely to be influenced by the thermal field and by the water pressure in the cracked area. A dynamical lineshaft model, integrated by an original representation of the crack, has been developed to investigate the possible vibratory symptoms related to a crack propagation. The vibrations are generally measured in correspondence of a rigid coupling which connects the motor shaft to the pump shaft, in a position which is rather far away from the crack. 1 × rev., 2 × rev., and 3 × rev. vibration components, which are generally displayed by the machine condition monitoring system and are the most significative symptoms of the presence of a transverse crack in a rotating shaft, are calculated.

Experimental Investigation of Heat Transfer Enhancement by Using Different Number of Fins in Circular Tube

2018 ◽  
Vol 6 (3) ◽  
pp. 1-12
Author(s):  
Kamil Abdul Hussien
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Cold Water ◽  
Finned Tube ◽  
Hot Water ◽  
Copper Tube ◽  
Smooth Tube ◽  
Tube Heat Exchanger ◽  
Mass Flow Rates ◽  
Flow Heat

Abstract-The present work investigates the enhancement of heat transfer by using different number of circular fins (8, 10, 12, 16, and 20) in double tube counter flow heat exchanger experimentally. The fins are made of copper with dimensions 66 mm OD, 22 mm ID and 1 mm thickness. Each fin has three of 14 mm diameter perforations located at 120o from each to another. The fins are fixed on a straight smooth copper tube of 1 m length, 19.9 mm ID and 22.2 mm OD. The tube is inserted inside the insulated PVC tube of 100 mm ID. The cold water is pumped around the finned copper tube, inside the PVC, at mass flow rates range (0.01019 - 0.0219) kg/s. The Reynold's number of hot water ranges (640 - 1921). The experiment results are obtained using six double tube heat exchanger (1 smooth tube and the other 5 are finned one). The results, illustrated that the heat transfer coefficient proportionally with the number of fin. The results also showed that the enhancement ratio of heat transfer for finned tube is higher than for smooth tube with (9.2, 10.2, 11.1, 12.1 13.1) times for number of fins (8, 10, 12, 16 and 20) respectively.

scholarly journals The Effect of Thermo-Mechanical Processing on Physical Properties of Processed Amaranth and Oat Bran Composites

2017 ◽  
Vol 6 (2) ◽  
pp. 82
Author(s):  
Sean X. Liu ◽  
Diejun Chen ◽  
George E. Inglett ◽  
Jingyuan Xu
Keyword(s):  
Physical Properties ◽  
High Speed ◽  
Functional Foods ◽  
Cold Water ◽  
Essential Amino Acids ◽  
Hot Water ◽  
Blood Cholesterol ◽  
Gluten Free ◽  
Oat Bran ◽  
Amaranth Flour

Amaranth-oat composites were developed using gluten free amaranth flour containing essential amino acids and minerals with oat products containing β-glucan, known for lowering blood cholesterol. Amaranth flour and oat bran concentrate (OBC) composites (1:4) were processed using different technologies, including dry mixing, baking, steaming, cold wet blending, and high speed homogenizing (Polytron PT6000) with cold water or hot water. The results showed that water holding capacities, pasting, and rheological properties were dramatically increased by wet blending, Polytron with cold water, and Polytron with hot water followed by drum drying. The processing procedures created dissimilar physical properties that will enhance the application of ancient grains and oat for functional foods that are suitable for people who are gluten-intolerant. In addition, the dietary fiber contents of composites were increased by the incorporation of OBC. The composites can be inexpensively prepared and processed. The new healthful products will be affordable for people who suffer from celiac disease or gluten-intolerant. These innovative gluten-free functional food products will help millions of gluten sensitive consumers enjoy heart-healthy functional foods.

Stability of Water-Lubricated, Hydrostatic, Conical Bearings With Spiral Grooves for High-Speed Spindles

2001 ◽  
Vol 124 (2) ◽  
pp. 398-405 ◽  
Author(s):  
S. Yoshimoto ◽  
S. Oshima ◽  
S. Danbara ◽  
T. Shitara
Keyword(s):  
High Speed ◽  
Water Pressure ◽  
Rotating Shaft ◽  
Pressurized Water ◽  
High Speeds ◽  
Theoretical Predictions ◽  
The Stability ◽  
Stability Of Water ◽  
Spiral Grooves ◽  
Good Agreement

In this paper, the stability of water-lubricated, hydrostatic, conical bearings with spiral grooves for high-speed spindles is investigated theoretically and experimentally. In these bearing types, pressurized water is first fed to the inside of the rotating shaft and then introduced into spiral grooves through feeding holes located at one end of each spiral groove. Therefore, water pressure is increased due to the effect of the centrifugal force at the outlets of the feeding holes, which results from shaft rotation. In addition, water pressure is also increased by the viscous pumping effect of the spiral grooves. The stability of the proposed bearing is theoretically predicted using the perturbation method, and calculated results are compared with experimental results. It was consequently found that the proposed bearing is very stable at high speeds and theoretical predictions show good agreement with experimental data.

scholarly journals Thermal Characteristics Analysis on Multi- Heat Pipe Induced Heat Exchanger

2019 ◽  
Vol 9 (2S2) ◽  
pp. 143-147 ◽  
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Pipe ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Cold Water ◽  
Hot Water ◽  
Working Fluid ◽  
Physical Parameters

In this investigation of multi heat pipe induced in heat exchanger shows the developments in heat transfer is to improve the efficiency of heat exchangers. Water is used as a heat transfer fluid and acetone is used as a working fluid. Rotameter is set to measure the flow rate of cold water and hot water. To maintain the parameter as experimental setup. Then set the mass flow rate of hot water as 40 LPH, 60LPH, 80 LPH, 100LPH, 120 LPH and mass flow rate of cold water as 20 LPH, 30 LPH, 40 LPH, 50 LPH, and 60 LPH. Then 40 C, 45 ºC, 50 ºC, 55 C, 60 ºC are the temperatures of hot water at inlet are maintained. To find some various physical parameters of Qc , hc , Re ,, Pr , Rth. The maximum effectiveness of the investigation obtained from condition of Thi 60 C, Tci 32 C and 100 LPH mhi, 60 LPH mci the maximum effectiveness attained as 57.25. Then the mhi as 100 LPH, mci as 60 LPH and Thi at 40 C as 37.6%. It shows the effectiveness get increased about 34.3 to the maximum conditions.

scholarly journals Simulation of the effectiveness of longitudinal rectangular fins on the efficiency of the double pipe heat exchanger

2019 ◽  
Vol 21 (4) ◽  
pp. 48-57
Author(s):  
N. F. Timerbaev ◽  
A. K. Ali ◽  
Omar Abdulhadi Mustafa Almohamed ◽  
A. R. Koryakin
Keyword(s):  
Heat Exchanger ◽  
Heat Exchangers ◽  
Cold Water ◽  
Tube Diameter ◽  
Hot Water ◽  
Outer Tube ◽  
Design Parameters ◽  
Double Pipe ◽  
Central Pipe ◽  
Pipe Heat

In this article, a mathematical simulation of a double pipe heat exchanger is carried out, having the longitudinal rectangular fins with the dimension of (2*3*1000) mm, mounted on the outer surface of the inner tube of the heat exchanger. In this paper, the advantage of using of that type of fins and its effect on the effectiveness of the heat exchanger are studied with the help of the computer program. The carried out research allowsmaking the calculation to find the optimum design parameters of heat exchangers. The outer tube diameter is (34.1mm) while the inner tube diameter is (16.05mm). The tubes wall thickness is (1.5mm) and the model length was (1 m). The hot water is flowing through the inner tube in parallel with the cold water that passing the outer tube. The hot and cold water temperature at the inlet is (75°C & 30°C) respectively. The mass flow rate inside the central pipe is (0.1 kg/s) while the annular pipe carrying (0.3 kg/s). In the present work, the program ANSYS Workbench 15.0 was used to find out the results of heat transfer as well as the behavior of liquids inside the heat exchangers.

scholarly journals Effect of Variable Confining Pressure on Cyclic Triaxial Behavior of K0-consolidated Soft Marine Clay

2018 ◽  
Vol 4 (4) ◽  
pp. 755
Author(s):  
Lei Sun
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Axial Strain ◽  
Water Pressure ◽  
Confining Pressure ◽  
Stress Path ◽  
Cyclic Stress ◽  
Marine Clay ◽  
Stress Ratios ◽  
Variable Confining Pressure

The effect of variable confining pressure (VCP) on the cyclic deformation and cyclic pore water pressure in K0-consolidated saturated soft marine clay were investigated with the help of the cyclic stress-controlled advanced dynamic triaxial test in undrained condition. The testing program encompassed three cyclic deviator stress ratios, CSR=0.189, 0.284 and 0.379 and three stress path inclinations ηampl=3,1 and 0.64. All tests with constant confining pressure (CCP) and variable confining pressure (VCP) have identical initial stress and average stress. The results were analyzed in terms of the accumulative normalized excess pore water pressure rqu recorded at the end of each stress cycle and permanent axial strain, as well as resilient modulus. Limited data suggest that these behavior are significantly affected by both of the VCP and CSR. For a given value of VCP, both of the pore water pressure rqu and permanent axial strains are consistently increase with the increasing values of CSR. However, for a given value of CSR, the extent of the influence of VCP and the trend is substantially depend on the CSR.

scholarly journals Antibacterial activity of ginger extracts and its essential oil on some of pathogenic bacteria

2010 ◽  
Vol 7 (3) ◽  
pp. 1159-1165
Author(s):  
Baghdad Science Journal
Keyword(s):  
Antimicrobial Activity ◽  
Antibacterial Activity ◽  
Essential Oil ◽  
Pathogenic Bacteria ◽  
Cold Water ◽  
Water Extract ◽  
Ethanolic Extract ◽  
Hot Water ◽  
Diffusion Method ◽  
Resistant Bacteria

The antimicrobial activity of ginger extracts ( cold-water, hot-water, ethanolic and essential oil ) against some of pathogenic bacteria ( Escherichia coli , Salmonella sp , Klebsiella sp , Serratia marcescens, Vibrio cholerae , Staphylococcus aureus , Streptococcus sp) was investigated using Disc diffusion method , and the results were compared with the antimicrobial activity of 12 antibiotics on the same bacteria . The results showed that the ginger extracts were more effective on gram-positive bacteria than gram-negative . V. cholerae and S. marcescens,were the most resistant bacteria to the extracts used , while highest inhibition was noticed against Streptococcus sp (28 mm) . The ethanolic extract showed the broadest antibacterial activity ( 11 to 28 mm ) , in comparison with moderate activity of essential oil , it was observed that the cold-water extract was more effective on the bacteria than hot-water extract . Ginger ethanolic extract presented higher diameter of inhibition zone for Streptococcus sp than in Ciprofloxacin , Cefotaxime , Cefalotin , Cephalexin and Cephaloridine , also it was found a similarity between the higher inhibition zones of ethanolic extract of ginger and some antibiotics for S. aureus , E. coli , Salmonella sp and Klebsiella sp . V. cholerae and S. marcescens,also highly resistant to antibiotics . Phytochemical analysis of ethanolic extract of ginger revealed the present of glycosides, terpenoids, flavonids and phenolic compounds

scholarly journals Potassium Recovery Potential of Selected Agroforestry and Organic Wastes in Ibadan, Nigeria

2017 ◽  
Vol 13 (6) ◽  
pp. 492
Author(s):  
Akindejoye F. ◽  
Hammed T.B. ◽  
Sridhar M.K.C.
Keyword(s):  
Cold Water ◽  
Organic Wastes ◽  
Hot Water ◽  
Water Extraction ◽  
Recovery Potential ◽  
Sodium Magnesium ◽  
Cheap Alternative ◽  
K Concentration ◽  
Coconut Fibre ◽  
Mineral Concentrations

This study explored potassium recovery from agroforestry wastes that may be a cheap alternative to imported ones. The wastes: Plantain Peel (PP), Coconut Fibre (CF), Coconut Shell (CS), Cocoa Pod (CP), Sugarcane Bagasse (SB), Sawdust (SD) and four common wood-fuel species - Antiaris toxicaria (Wd1), Cordia millenii (Wd2), Khayas senegalensis (Wd3) and Milicia excelsa (Wd4) were assessed for their ash content (AC) and moisture content (MC), using standard procedures of AOAC. Atomic Absorption spectrophotometer was used to determine mineral concentrations: potassium, sodium, magnesium, calcium, zinc, lead and iron of the wastes. In addition, efficacy of three methods of extracting potassium from ashes: cold water extraction at 35 OC, hot water extraction at 90 OC and steam extraction was assessed. Data were analysed using descriptive statistics and correlation test at p˂0.05. Wastes with highest values in terms of AC and MC were: CP (AC- 11.62 ± 0.3 %) and SB (MC- 82 ± 2.64 %). The highest concentration of K (mg·kg -1 ) was found in CP (8,387.50 ± 2.00 mg·kg-1 ). Cold water extraction gave the most potassium yield (88.44 %) and the highest solid potash content was found in PP (68 500 mg·kg -1 ) while CP had the highest K concentration (12.51±0.20 g·dm-3 ). Cocoa pod, plantain peel and Cordia millenii are very good sources of agroforestry/organic wastes for local production of potassium both in terms of solid potash yield and potassium recovery potential. Development of a suitable technology which can be used to extract potassium locally is recommended.

scholarly journals Effect of pre-sowing treatments and growing media on seed germination and seedling growth of Albizia lebbeck (L.) Benth

2018 ◽  
Vol 10 (3) ◽  
pp. 860-863
Author(s):  
Naresh Kumar ◽  
A. K. Handa ◽  
Inder Dev ◽  
Asha Ram ◽  
A. R. Uthappa ◽  
...  
Keyword(s):  
Seedling Growth ◽  
Room Temperature ◽  
Cold Water ◽  
Hot Water ◽  
Albizia Lebbeck ◽  
Physical Dormancy ◽  
Growing Media ◽  
Hard Seed ◽  
Collar Diameter ◽  
Hard Seed Coat

The seeds of Albizia lebbeck have been observed to exhibit physical dormancy due to presence of hard seed-coat. To overcome this problem, the seeds were subjected to seven pre-sowing treatments viz., T1-immersion of seeds in cold water for 12 h; T2-immersion of seeds in cold water for 24 h; T3-immersion of seeds in hot water (100 °C) and subsequent cooling at room temperature for 12 h; T4-immersion of seeds in hot water (100 °C) and subsequent cooling at room temperature for 24 h; T5-immersion of seeds in cold water for 12 h followed by immersion in hot water (100 °C) and allowed to cool for 1 h; T6-immersion of seeds in cold water for 24 h followed by immersion in hot water (100 °C) and allowed to cool for 1 h. Untreated seeds served as control (T0). Treatment T3 gave highest germination (96%) which was comparable with T5 (95 %), T4 (94 %) and T6 (93%). Nine growing media viz., T1: soil,  T2: soil+sand (2:1), T3: soil+perlite (2:1), T4: soil+Farm Yard Manure (FYM) (2:1), T5: soil+vermicompost (2:1), T6: soil+sand+FYM (1:1:1), T7: soil+sand+vermicompost (1:1:1), T8: soil+perlite+FYM (1:1:1) and T9: soil+perlite+ vermicompost (1:1:1) were, also, studied for their effect on seedling growth of A. lebbeck. Among these media, maximum values of shoot length (23.82 cm), root length (21.14 cm), collar diameter (3.59 mm) and seedling quality index (0.350) were observed in T7.

scholarly journals Sacrificial amphiphiles: Eco-friendly chemical herders as oil spill mitigation chemicals

2015 ◽  
Vol 1 (5) ◽  
pp. e1400265 ◽  
Author(s):  
Deeksha Gupta ◽  
Bivas Sarker ◽  
Keith Thadikaran ◽  
Vijay John ◽  
Charles Maldarelli ◽  
...  
Keyword(s):  
Crude Oil ◽  
Oil Spill ◽  
Oil Spills ◽  
Cold Water ◽  
Marine Ecosystem ◽  
Hot Water ◽  
Sea Surface ◽  
Marine Biota ◽  
Polar Group ◽  
Branched Chain

Crude oil spills are a major threat to marine biota and the environment. When light crude oil spills on water, it forms a thin layer that is difficult to clean by any methods of oil spill response. Under these circumstances, a special type of amphiphile termed as “chemical herder” is sprayed onto the water surrounding the spilled oil. The amphiphile forms a monomolecular layer on the water surface, reducing the air–sea surface tension and causing the oil slick to retract into a thick mass that can be burnt in situ. The current best-known chemical herders are chemically stable and nonbiodegradable, and hence remain in the marine ecosystem for years. We architect an eco-friendly, sacrificial, and effective green herder derived from the plant-based small-molecule phytol, which is abundant in the marine environment, as an alternative to the current chemical herders. Phytol consists of a regularly branched chain of isoprene units that form the hydrophobe of the amphiphile; the chain is esterified to cationic groups to form the polar group. The ester linkage is proximal to an allyl bond in phytol, which facilitates the hydrolysis of the amphiphile after adsorption to the sea surface into the phytol hydrophobic tail, which along with the unhydrolyzed herder, remains on the surface to maintain herding action, and the cationic group, which dissolves into the water column. Eventual degradation of the phytol tail and dilution of the cation make these sacrificial amphiphiles eco-friendly. The herding behavior of phytol-based amphiphiles is evaluated as a function of time, temperature, and water salinity to examine their versatility under different conditions, ranging from ice-cold water to hot water. The green chemical herder retracted oil slicks by up to ~500, 700, and 2500% at 5°, 20°, and 35°C, respectively, during the first 10 min of the experiment, which is on a par with the current best chemical herders in practice.

Sign in / Sign up

Export Citation Format

Share Document