Third Paper: The Influence of Engine Design on Spark Knock at High Speeds

1967 ◽  
Vol 182 (1) ◽  
pp. 95-103 ◽  
Author(s):  
J. B. Perrett
Keyword(s):  
High Speed ◽  
Considerable Time ◽  
Research Octane Number ◽  
High Speeds ◽  
Spark Timing ◽  
Engine Design ◽  
Present Generation ◽  
A Chain ◽  
Swept Volume ◽  
Exhaust Valves

Modern motor roads permit cars to be driven at high speeds for many miles. In these circumstances it is possible for engines to be operating in a condition of spark knock for a considerable time. Such knock might not be detected by the driver, but could initiate a chain of events leading to damage to the engine. A realistic procedure has been devised for carrying out tests for spark knock at high speeds, employing cars mounted on vehicle dynamometers. Tests on 30 European car models, all having manual transmissions, led to the critical knock speed concept for making comparisons between the high speed knock susceptibilities of various designs of engine. These comparisons have shown that, in service, over-advanced spark timing is frequently the prime reason for the occurrence of high speed knock. With spark timing set at the minimum advance required for the engine to develop its best torque, octane requirement is influenced by compression ratio, brake horsepower per litre, cylinder swept volume and disposition of the exhaust valves. Also to a small extent, by combustion chamber design and the amount of induction heating employed. Given attention to the above factors, it is felt that the high speed anti-knock requirements of the present generation of engines can be met by currently marketed gasolines of 98/99 Research octane number (ON).

A Statistical Study of Process Variables to Optimize a High Speed Curtain Coater: Part I

TAPPI Journal ◽  
2009 ◽  
Vol 8 (1) ◽  
pp. 20-26 ◽  
Author(s):  
PEEYUSH TRIPATHI ◽  
MARGARET JOYCE ◽  
PAUL D. FLEMING ◽  
MASAHIRO SUGIHARA
Keyword(s):  
Boundary Layer ◽  
Experimental Design ◽  
High Speed ◽  
Statistical Study ◽  
Process Variables ◽  
High Speeds ◽  
The Stability ◽  
Air Removal ◽  
Removal System

Using an experimental design approach, researchers altered process parameters and material prop-erties to stabilize the curtain of a pilot curtain coater at high speeds. Part I of this paper identifies the four significant variables that influence curtain stability. The boundary layer air removal system was critical to the stability of the curtain and base sheet roughness was found to be very important. A shear thinning coating rheology and higher curtain heights improved the curtain stability at high speeds. The sizing of the base sheet affected coverage and cur-tain stability because of its effect on base sheet wettability. The role of surfactant was inconclusive. Part II of this paper will report on further optimization of curtain stability with these four variables using a D-optimal partial-facto-rial design.

RED CUT COBALT

Alloy Digest ◽  
1980 ◽  
Vol 29 (8) ◽  
Keyword(s):  
Fracture Toughness ◽  
Cast Iron ◽  
High Speed ◽  
Elevated Temperatures ◽  
High Speed Steel ◽  
Heat Treating ◽  
High Speeds ◽  
Red Hardness ◽  
Nonferrous Alloys ◽  
Cutting Point

Abstract RED CUT COBALT steel is made by adding 5% cobalt to the conventional 18% tungsten -4% chromium-1% vanadium high-speed steel. Cobalt increases hot or red hardness and thus enables the tool to maintain a higher hardness at elevated temperatures. This steel is best adapted for hogging cuts or where the temperature of the cutting point of the tool in increased greatly. It is well adapted for tools to be used for reaming cast-iron engine cylinders, turning alloy steel or cast iron and cutting nonferrous alloys at high speeds. This datasheet provides information on composition, physical properties, and hardness as well as fracture toughness. It also includes information on forming, heat treating, and machining. Filing Code: TS-367. Producer or source: Teledyne Vasco.

CPM REX 25

Alloy Digest ◽  
1980 ◽  
Vol 29 (7) ◽  
Keyword(s):  
Heat Treatment ◽  
High Speed ◽  
High Speed Steel ◽  
High Hardness ◽  
Heat Treating ◽  
High Speeds ◽  
Aisi Type ◽  
Tool Performance ◽  
End Mills ◽  
Machining Operations

Abstract CPM REX 25 is a super high-speed steel made without cobalt. It is comparable to AISI Type T15 cobalt-containing high-speed steel in response to heat treatment, properties, and tool performance. CPM REX 25 is recommended for machining operations requiring heavy cuts, high speeds and feeds, and difficult-to-machine materials of high hardness and abrasion resistance. Typical applications are boring tools, drills, gear cutters, punches, form tools, end mills and broaches. This datasheet provides information on composition, physical properties, hardness, and elasticity as well as fracture toughness. It also includes information on forming, heat treating, machining, and surface treatment. Filing Code: TS-365. Producer or source: Crucible Materials Corporation.

A Method of Making High-Speed Compression Tests on Small Copper Cylinders

1948 ◽  
Vol 15 (3) ◽  
pp. 248-255
Author(s):  
E. T. Habib
Keyword(s):  
High Speed ◽  
Underwater Explosion ◽  
Dynamic Calibration ◽  
Test Apparatus ◽  
Compression Tests ◽  
High Speeds

Abstract In mechanical gages used to measure the pressure from an underwater explosion, small copper cylinders are compressed at high speeds. This paper describes the test apparatus designed for the dynamic calibration of these cylinders, presents the results obtained with this apparatus, and compares these results with those obtained by other experimenters.

The High Performance Toroidal Engine Concept (HiPerTEC)

2011 ◽  
Author(s):  
Karl V. Hoose ◽  
Eric E. Shorey
Keyword(s):  
High Performance ◽  
Combustion Process ◽  
Thermodynamic Cycle ◽  
Unmanned Vehicles ◽  
Advanced Materials ◽  
Specific Power ◽  
Operating Characteristics ◽  
Free Piston ◽  
Engine Design ◽  
Swept Volume

The traditional reciprocating I.C. engine has evolved to a point where significant improvements in thermal efficiency and specific power are not expected. Modifications to existing engines may prove to be difficult and expensive while resulting in only marginal gains. In addition, most modifications result in added components that often increase cost and decrease reliability of the system as a whole. For applications requiring major advances in performance, such as unmanned vehicles, meeting mission requirements will likely stem from a revolutionary rather than an evolutionary engine design. The slider crank mechanism is a major impediment to the traditional reciprocating I.C. engine. Although this mechanism has been used for the past 100 years, it is very wasteful of the available energy supplied by the combustion process, where piston-liner interactions from this arrangement accounts for 50–70% of the total friction losses in this engine design. Eliminating the slider crank could significantly reduce friction losses and provide additional benefits that can increase fuel conversion efficiency. The HiPerTEC engine is an opposed, free-piston engine arranged in a toroidal configuration with two counter reciprocating sets of pistons. The counter reciprocating masses eliminate the vibration found in linear free-piston engines. The HiPerTEC employs a unique shared volume configuration where the swept volume is twice the physical cylinder volume. This attribute offers a significant increase in specific power, while the free-piston characteristics provide for substantial gains in thermodynamic cycle efficiency. An eight cylinder/chamber arrangement offers balanced operation in both two and four-stroke cycle modes to allow for a wide operating envelope. The final HiPerTEC configuration will require advanced materials to address lubrication and cooling requirements. This paper discusses the HiPerTEC design, operating characteristics, development progress to date, and the challenges that lie ahead.

scholarly journals Physical Simulations of High Speed and Low Power NanoMagnet Logic Circuits

2018 ◽  
Vol 8 (4) ◽  
pp. 37 ◽  
Author(s):  
Giovanna Turvani ◽  
Laura D’Alessandro ◽  
Marco Vacca
Keyword(s):  
High Speed ◽  
Logic Circuits ◽  
Micromagnetic Simulations ◽  
Electrical Fields ◽  
Nanomagnet Logic ◽  
Nanomagnetic Logic ◽  
Elastic Effect ◽  
Physical Simulations ◽  
A Chain ◽  
Beyond Cmos

Among all “beyond CMOS” solutions currently under investigation, nanomagnetic logic (NML) technology is considered to be one of the most promising. In this technology, nanoscale magnets are rectangularly shaped and are characterized by the intrinsic capability of enabling logic and memory functions in the same device. The design of logic architectures is accomplished by the use of a clocking mechanism that is needed to properly propagate information. Previous works demonstrated that the magneto-elastic effect can be exploited to implement the clocking mechanism by altering the magnetization of magnets. With this paper, we present a novel clocking mechanism enabling the independent control of each single nanodevice exploiting the magneto-elastic effect and enabling high-speed NML circuits. We prove the effectiveness of this approach by performing several micromagnetic simulations. We characterized a chain of nanomagnets in different conditions (e.g., different distance among cells, different electrical fields, and different magnet geometries). This solution improves NML, the reliability of circuits, the fabrication process, and the operating frequency of circuits while keeping the energy consumption at an extremely low level.

Stability of Water-Lubricated, Hydrostatic, Conical Bearings With Spiral Grooves for High-Speed Spindles

2001 ◽  
Vol 124 (2) ◽  
pp. 398-405 ◽  
Author(s):  
S. Yoshimoto ◽  
S. Oshima ◽  
S. Danbara ◽  
T. Shitara
Keyword(s):  
High Speed ◽  
Water Pressure ◽  
Rotating Shaft ◽  
Pressurized Water ◽  
High Speeds ◽  
Theoretical Predictions ◽  
The Stability ◽  
Stability Of Water ◽  
Spiral Grooves ◽  
Good Agreement

In this paper, the stability of water-lubricated, hydrostatic, conical bearings with spiral grooves for high-speed spindles is investigated theoretically and experimentally. In these bearing types, pressurized water is first fed to the inside of the rotating shaft and then introduced into spiral grooves through feeding holes located at one end of each spiral groove. Therefore, water pressure is increased due to the effect of the centrifugal force at the outlets of the feeding holes, which results from shaft rotation. In addition, water pressure is also increased by the viscous pumping effect of the spiral grooves. The stability of the proposed bearing is theoretically predicted using the perturbation method, and calculated results are compared with experimental results. It was consequently found that the proposed bearing is very stable at high speeds and theoretical predictions show good agreement with experimental data.

scholarly journals The Concept of Development and Implementation of High-Speed Transport

2020 ◽  
Vol 18 (1) ◽  
pp. 58-72
Author(s):  
V. M. Alexeev ◽  
A. V. Vaganov ◽  
M. V. Katina
Keyword(s):  
High Speed ◽  
Magnetic Levitation ◽  
Transport Systems ◽  
Rolling Stock ◽  
Design Elements ◽  
Safety Issues ◽  
Current Collection ◽  
High Speeds ◽  
Technical Solutions ◽  
Original Approach

The article discusses the issues of implementation and organization of high-speed transport. The objective of the article is to consider possible options for implementing highspeed (HS) motion systems using the principle of magnetic levitation, which will ensure high speeds for delivery of goods and carrying people over long distances. To achieve this objective, it is necessary to develop an engine and technical solutions for design of HS rolling stock, make decisions on energy supply infrastructure and the HS track, address safety issues and new control systems considering the state of the infrastructure and its design elements. The article discusses several options for implementation of high-speed transport systems, differing in the power supply system, current collection and track based on the magnetic levitation approach. An original approach is proposed in implementation of magnetic levitation transport using the technology of electromagnetic guns designed to implement traction forces of a magnetic levitation vehicle. The advantage of this approach is that it opens the possibility of maneuvering for the vehicle while driving. This allows to abandon switch turnouts, now significantly limiting the use of magnetic levitation transport. A mathematical model describing interaction of an electromagnetic gun and supermagnets located on the track is considered. In constructing the model, methods of the theory of electromagnetic field and interaction of magnetic bodies were used, and when constructing a model of interaction of rolling stock with a magnetic track, methods of mathematical algebra and the Cauchy theorem were used. The article discusses various principles of organization of movement using the magnetic levitation for urban, suburban, and intercity transport.

The Measurement and Analysis of Ball Motion in High Speed Deep Groove Ball Bearings

1975 ◽  
Vol 97 (3) ◽  
pp. 341-348 ◽  
Author(s):  
R. J. Boness ◽  
J. J. Chapman
Keyword(s):  
High Speed ◽  
Experimental Results ◽  
Complete Analysis ◽  
Ball Speed ◽  
Rolling Axis ◽  
High Speeds ◽  
Deep Groove ◽  
Wide Range ◽  
Ring Mode ◽  
Ball Motion

This paper reports on a study of ball motion, including the measurement of ball rolling axis, in deep groove bearings operating at high speeds under thrust load conditions. The technique employed relies on viewing the test bearing, operating in the conventional fixed outer ring mode, through a rotating prism which eliminates optically the gross rotation of the separator. Videotape recordings of a selected ball, distinctively marked and illuminated stroboscopically, allows a complete analysis of ball bearing kinematics. Experimental results of separator speed, ball speed and rolling axis together with separator slip, ball slip and spin velocities at both the inner and outer raceway contacts are presented for a wide range of loads and shaft speeds up to 12,000 rev/min. These results are compared with the existing theory of Jones. Discrepancies between predicted and actual ball motion are due to the assumption made by Jones in neglecting bearing element slip. A further analysis of the experimental results including both gyroscopic torques and slip based on elastohydrodynamic traction values for the test lubricant explains actual ball motion more fully.

Dynamics of Machine Tool Spindle/Bearing Systems Under Thermal Growth

1997 ◽  
Vol 119 (4) ◽  
pp. 875-882 ◽  
Author(s):  
Bert R. Jorgensen ◽  
Yung C. Shin
Keyword(s):  
Thermal Expansion ◽  
Dynamic Response ◽  
Heat Generation ◽  
High Speed ◽  
Transfer Model ◽  
Good Prediction ◽  
High Speeds ◽  
Spindle Bearing ◽  
Thermal Growth ◽  
Bearing Stiffness

Increased use of high-speed machining creates the need to predict spindle/bearing performance at high speeds. Spindle dynamic response is a function of the nonlinear bearing stiffness. At high speeds, thermal expansion can play an important role in bearing stiffness. A complete bearing load-deflection analysis including thermal expansion is derived and is coupled with an analysis of spindle dynamic response. Steady-state temperature distribution is found from heat generation at the contact point and from a quasi three-dimensional heat transfer model. Numerical solutions give a good prediction of thermal growth and heat generation in the bearing. Predicted high-speed spindle frequencies show good agreement with experimentation. The effects of loading condition and bearing material type on bearing stiffness are also shown.

Sign in / Sign up

Export Citation Format

Share Document