scholarly journals NUMERICAL MODELLING OF COMPRESSIVE CHARACTERISTICS OF AUXETIC STRUCTURES

2018 ◽  
Vol 18 ◽  
pp. 38 ◽  
Author(s):  
Michaela Neuhäuserová ◽  
Petr Koudelka
Keyword(s):  
Numerical Analysis ◽  
Mechanical Behaviour ◽  
Three Dimensional ◽  
Deformation Energy ◽  
Unit Cell ◽  
Geometrical Parameters ◽  
Static Compression ◽  
Virtual Experiments ◽  
Auxetic Structures ◽  
Loading Modes

The paper is focused on numerical analysis of mechanical behaviour of auxetic structures with re-entrant tetrakaidecahedral unit cell subjected to uni-axial quasi-static compression. The mechanical behaviour was evaluated inversely with respect to selected geometrical parameters of the unit cell and two different loading modes. Finite element method was used for the numerical analysis of the problem. A set of fully parametric tools has been developed, which enabled automated execution and evaluation of virtual experiments. From results of the simulations, Young’s modulus, the characteristics of the Poisson’s ratio function, and the deformation energy density were estimated. The relation between these characteristics and geometry of the unit cell, particularly the re-entrant angle and the relative density, was evaluated. Results of the numerical simulations for the unit cell and representative volume element of its three-dimensional periodic assembly are presented.

scholarly journals Finite Element Study on the Effect of Geometrical Parameters on the Mechanical Behavior of 3D Reentrant Auxetic Honeycombs.

2022 ◽  
pp. 1-7
Author(s):  
Sai Adithya Vanga ◽  
Aravind Rajan Ayagara ◽  
Rohan Gooty ◽  
Taha Hussain ◽  
Moulshree Srivastava
Keyword(s):  
Finite Element ◽  
Energy Absorption ◽  
Poisson’S Ratio ◽  
Bulk Material ◽  
Three Dimensional ◽  
Unit Cell ◽  
Poisson's Ratio ◽  
Geometrical Parameters ◽  
Self Healing ◽  
Strain Behavior

Auxetic materials are a special case of cellular materials, which exhibit a negative Poisson’s ratio. This in fact is the reason behind their peculiar behavior i.e. lateral shrinkage under longitudinal compression and vice versa. Since these materials do not obey the laws of “normal” materials and go beyond common sense, they are still an emerging class which can be put to use for various purposes like self-locking reinforcing fibers in composites, controlled release media, self-healing films, piezoelectric sensors, and also be used in biomedical engineering. Their stress-strain behavior, Poisson’s ratio and impact energy absorption are controlled by bulk material as well as the unit cell geometry. Among many forms of auxetic structures available, we have chosen a three-dimensional reentrant auxetic honeycomb unit cell. The unit cell geometrical parameters were taken from literature. In this study, we try to understand the effects of strut angle through finite element simulations while keeping the bulk material, unit cell size, strut thickness and number of repetitions constant. A total of three different angles were tested, based on which we conclude that as angle increases, the Poisson’s ratio increases and Energy absorption is maximum at 30 deg.

Compressive Properties of Corevo® Foam under Uni-Axial Loading Based on Experimental and Numerical Analysis

2014 ◽  
Vol 597 ◽  
pp. 121-126
Author(s):  
M.A. Sulong ◽  
Vincent Mathier ◽  
Thomas Fiedler ◽  
Irina V. Belova ◽  
Graeme E. Murch
Keyword(s):  
Numerical Analysis ◽  
Yield Stress ◽  
Three Dimensional ◽  
Axial Loading ◽  
Micro Computed Tomography ◽  
Compressive Properties ◽  
Element Analysis ◽  
Static Compression ◽  
Initial Yield Stress ◽  
Three Dimensional Finite Element

This manuscript investigates the compressive properties of Corevo®foam. Corevo®foam is a cellular metal manufactured by the infiltration casting of salt dough with aluminium. Corevo®foam samples with different porosities are tested by using quasi-static compression loading. Their mechanical properties (i.e.: effective Young’s modulus, Poisson’s ratio, initial yield stress and material yield stress) are then compared to reveal the importance of the density difference. In addition, three-dimensional finite element analysis is performed on models generated from micro-computed tomography (μCT). The results of two different pore sizes are obtained and compared in the scope of this work. These numerical results are verified by comparison with the experimental analysis. A sound agreement is found. Numerical analysis in this work also includes the investigation of the mechanical material anisotropy and plastic deformation.

scholarly journals Numerical analysis of plasmonic metasurfaces for fluorescence enhancement

2021 ◽  
Vol 255 ◽  
pp. 04004
Author(s):  
Roxana Tomescu ◽  
Florin Nita ◽  
Stefan Caramizoiu ◽  
Veronica Anastasoaie ◽  
Dana Cristea
Keyword(s):  
Numerical Analysis ◽  
Fluorescence Enhancement ◽  
Rhodamine 6G ◽  
Collection Efficiency ◽  
Fdtd Method ◽  
Three Dimensional ◽  
Geometrical Parameters ◽  
Excitation Field ◽  
Rectangular Array ◽  
Different Types

The paper presents an extensive numerical analysis performed by three-dimensional (3D) simulations using the finite difference in time and space (FDTD) method to identify the optimal geometry, size and configuration of the nano-antennas that constitute a plasmonic metasurface. The aim was to achieve the highest resonance at various wavelengths (NIR-VIS), for local enhancement of the excitation field and collection efficiency of emitted photons. We investigated ten different types of metals, two shapes (disks and U-shape resonators) and various geometrical parameters for the nanoresonators composing the metasurface. The best results for Rhodamine 6G excitation and emission were obtained using silver resonators with 105 nm diameter of the cylinder elements in a rectangular array with a 110 nm period, and with 110 nm long U-shape placed at a period of 40 nm.

Compression behavior of three-dimensional printed polymer lattice structures

2018 ◽  
Vol 233 (8) ◽  
pp. 1574-1584 ◽  
Author(s):  
Mohammed Al Rifaie ◽  
Ahsan Mian ◽  
Raghavan Srinivasan
Keyword(s):  
Energy Absorption ◽  
Lattice Structure ◽  
Three Dimensional ◽  
Unit Cell ◽  
The Body ◽  
Basic Unit ◽  
Lattice Structures ◽  
Body Centered Cubic ◽  
Static Compression ◽  
Compression Behavior

This paper focuses on the compression behavior of additively manufactured or three-dimensional printed polymer lattice structures of different configurations. The body-centered cubic lattice unit cell, which has been extensively investigated for energy absorption applications, is the starting point for this research. In this study, the lattice structure based on the body-centered cubic unit cell was modified by adding vertical struts in different arrangements to create three additional configurations. Four lattice structure designs were selected for comparison: the basic unit cell (body centered cubic), body centered cubic with vertical struts added to all nodes in the lattice, body centered cubic with vertical struts added to alternate nodes in the lattice, and body centered cubic with gradient in the number of vertical bars in the lattice. Samples of all four designs were prepared using acrylonitrile–butadiene–styrene polymer by three-dimensional printing. The stiffness, failure loads, and energy absorption behaviors of all four configurations were determined under quasi-static compression loading. Specific properties were calculated by normalizing the test properties by the sample mass. It is observed from experimental data that selective placement of vertical support struts in the unit cell influences both the absolute and specific mechanical properties of lattice structures.

Three dimensional numerical analysis of heat transfer during spray quenching of 22MnB5 steel with a single nozzle

2020 ◽  
Author(s):  
Emre Bulut ◽  
Gökhan Sevilgen ◽  
Ferdi Eşiyok ◽  
Ferruh Öztürk ◽  
Tuğçe Turan Abi
Keyword(s):  
Heat Transfer ◽  
Numerical Analysis ◽  
Three Dimensional ◽  
22Mnb5 Steel

scholarly journals Energy Loss in Steep Open Channels with Step-Pools

Water ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 72
Author(s):  
Suresh Kumar Thappeta ◽  
S. Murty Bhallamudi ◽  
Venu Chandra ◽  
Peter Fiener ◽  
Abul Basar M. Baki
Keyword(s):  
Energy Loss ◽  
Flow Rate ◽  
Recirculation Zone ◽  
Three Dimensional ◽  
Nonlinear Function ◽  
Open Channels ◽  
Geometrical Parameters ◽  
Transition Flow ◽  
Cumulative Energy ◽  
Zone Velocity

Three-dimensional numerical simulations were performed for different flow rates and various geometrical parameters of step-pools in steep open channels to gain insight into the occurrence of energy loss and its dependence on the flow structure. For a given channel with step-pools, energy loss varied only marginally with increasing flow rate in the nappe and transition flow regimes, while it increased in the skimming regime. Energy loss is positively correlated with the size of the recirculation zone, velocity in the recirculation zone and the vorticity. For the same flow rate, energy loss increased by 31.6% when the horizontal face inclination increased from 2° to 10°, while it decreased by 58.6% when the vertical face inclination increased from 40° to 70°. In a channel with several step-pools, cumulative energy loss is linearly related to the number of step-pools, for nappe and transition flows. However, it is a nonlinear function for skimming flows.

Prediction of internal geometry and tensile behavior of 3D woven solid structures by mathematical coding

2021 ◽  
pp. 152808372110013
Author(s):  
Vivek R Jayan ◽  
Lekhani Tripathi ◽  
Promoda Kumar Behera ◽  
Michal Petru ◽  
BK Behera
Keyword(s):  
Volume Fraction ◽  
Three Dimensional ◽  
Areal Density ◽  
Woven Fabrics ◽  
Tensile Behavior ◽  
Geometrical Parameters ◽  
Fiber Volume ◽  
Acceptable Error ◽  
Internal Geometry ◽  
Unit Cells

The internal geometry of composite material is one of the most important factors that influence its performance and service life. A new approach is proposed for the prediction of internal geometry and tensile behavior of the 3 D (three dimensional) woven fabrics by creating the unit cell using mathematical coding. In many technical applications, textile materials are subjected to rates of loading or straining that may be much greater in magnitude than the regular household applications of these materials. The main aim of this study is to provide a generalized method for all the structures. By mathematical coding, unit cells of 3 D woven orthogonal, warp interlock and angle interlock structures have been created. The study then focuses on developing code to analyze the geometrical parameters of the fabric like fabric thickness, areal density, and fiber volume fraction. Then, the tensile behavior of the coded 3 D structures is studied in Ansys platform and the results are compared with experimental values for authentication of geometrical parameters as well as for tensile behavior. The results show that the mathematical coding approach is a more efficient modeling technique with an acceptable error percentage.

Optimization of the Navy’s three-dimensional mine impact burial prediction simulation model, Impact35, using high-order numerical methods

2021 ◽  
pp. 154851292110286
Author(s):  
Athanasios Donas ◽  
Ioannis Famelis ◽  
Peter C Chu ◽  
George Galanis
Keyword(s):  
Numerical Analysis ◽  
Numerical Methods ◽  
Prediction Model ◽  
Simulation Model ◽  
Three Dimensional ◽  
Simulation System ◽  
High Order ◽  
Alternative Methodology ◽  
Runge Kutta ◽  
Fifth Order

The aim of this paper is to present an application of high-order numerical analysis methods to a simulation system that models the movement of a cylindrical-shaped object (mine, projectile, etc.) in a marine environment and in general in fluids with important applications in Naval operations. More specifically, an alternative methodology is proposed for the dynamics of the Navy’s three-dimensional mine impact burial prediction model, Impact35/vortex, based on the Dormand–Prince Runge–Kutta fifth-order and the singly diagonally implicit Runge–Kutta fifth-order methods. The main aim is to improve the time efficiency of the system, while keeping the deviation levels of the final results, derived from the standard and the proposed methodology, low.

scholarly journals Air Ventilation Performance of School Classrooms with Respect to the Installation Positions of Return Duct

2021 ◽  
Vol 13 (11) ◽  
pp. 6188
Author(s):  
Sungwan Son ◽  
Choon-Man Jang
Keyword(s):  
Air Quality ◽  
Numerical Analysis ◽  
Indoor Air Quality ◽  
Indoor Air ◽  
Three Dimensional ◽  
Cross Infection ◽  
School Students ◽  
Height Range ◽  
Air Ventilation ◽  
Ventilation Performance

For students, who spend most of their time in school classrooms, it is important to maintain indoor air quality (IAQ) to ensure a comfortable and healthy life. Recently, the ventilation performance for indoor air quality in elementary schools has emerged as an important social issue due to the increase in the number of days of continuous high concentrations of particulate matter. Three-dimensional numerical analysis has been introduced to evaluate the indoor airflow according to the installation location of return diffusers. Considering the possibility of the cross-infection of infectious diseases between students due to the direction of airflow in the classroom, the airflow angles of the average respiratory height range of elementary school students, between 1.0 and 1.5 m, are analyzed. Throughout the numerical analysis inside the classroom, it is found that the floor return system reduces the indoor horizontal airflow that causes cross-infection among students by 20% compared to the upper return systems. Air ventilation performance is also analyzed in detail using the results of numerical simulation, including streamlines, temperature and the age of air.

Sign in / Sign up

Export Citation Format

Share Document