Three-dimensional grain angle measurement of softwood (Hinoki cypress) using near infrared spatially and spectrally resolved imaging (NIR-SSRI)

Holzforschung ◽  
2019 ◽  
Vol 73 (9) ◽  
pp. 817-826
Author(s):  
Te Ma ◽  
Tetsuya Inagaki ◽  
Satoru Tsuchikawa
Keyword(s):  
Near Infrared ◽  
Linear Regression Analysis ◽  
Measurement Techniques ◽  
Three Dimensional ◽  
Gaussian Process Regression ◽  
Nonlinear Least Squares ◽  
Angle Measurement ◽  
Hinoki Cypress ◽  
Spectrally Resolved ◽  
Surface Angle

Abstract As the strength of wood is greatly affected by its three-dimensional (3D) grain angles (the dive angle and the surface angle), the wood industry today requires automatic, rapid, and robust measurement techniques for measuring them simultaneously. In the present study, a near infrared spatially and spectrally resolved imaging (NIR-SSRI) system was designed in a line scan model, mainly including an NIR hyperspectral imaging camera and a halogen spotlight source (Ø 1 mm). Spatially resolved diffuse reflectance images at three target wavelengths (1002 nm, 1217 nm, and 1413 nm) were obtained from Hinoki cypress [Chamaecyparis obtusa (Siebold & Zucc.) Endl.] samples at various (0°, 3°, 6°, … 45°) dive angles and surface angles (0°, 3°, 6°, … 45°). The scattering patterns caused by the “tracheid effect” were almost elliptical. Subsequently, nonlinear least squares fitting was used to determine their eccentricities (e) and rotation angles (θ). The e values at each selected wavelength were highly correlated with the dive angle reference values; and the global identification model developed using Gaussian process regression (GPR) under five-fold cross-validation (CV) reached a determination coefficient (r2) of 0.98 with a root mean square error (RMSE) of 2.2°. On the other hand, local surface angle identification models developed using linear regression analysis achieved determination coefficients higher than 0.90 on r2 and an RMSE of CV lower than 3.8° when the dive angle was lower than 30°.

scholarly journals Spectrally resolved helium absorption from the extended atmosphere of a warm Neptune-mass exoplanet

Science ◽  
2018 ◽  
Vol 362 (6421) ◽  
pp. 1384-1387 ◽  
Author(s):  
R. Allart ◽  
V. Bourrier ◽  
C. Lovis ◽  
D. Ehrenreich ◽  
J. J. Spake ◽  
...  
Keyword(s):  
Large Scale ◽  
Near Infrared ◽  
Mass Loss Rate ◽  
Three Dimensional ◽  
Neutral Hydrogen ◽  
Blue Shift ◽  
Spectral Signature ◽  
Night Side ◽  
Spectrally Resolved ◽  
Infrared Triplet

Stellar heating causes atmospheres of close-in exoplanets to expand and escape. These extended atmospheres are difficult to observe because their main spectral signature—neutral hydrogen at ultraviolet wavelengths—is strongly absorbed by interstellar medium. We report the detection of the near-infrared triplet of neutral helium in the transiting warm Neptune-mass exoplanet HAT-P-11b by using ground-based, high-resolution observations. The helium feature is repeatable over two independent transits, with an average absorption depth of 1.08 ± 0.05%. Interpreting absorption spectra with three-dimensional simulations of the planet’s upper atmosphere suggests that it extends beyond 5 planetary radii, with a large-scale height and a helium mass loss rate of ≲3 × 105 grams per second. A net blue-shift of the absorption might be explained by high-altitude winds flowing at 3 kilometers per second from day to night-side.

Urban energetics applications and Geomatic technologies in a Smart City perspective

2015 ◽  
Vol 6 (1) ◽  
pp. 19-29 ◽  
Author(s):  
G. Bitelli ◽  
P. Conte ◽  
T. Csoknyai ◽  
E. Mandanici
Keyword(s):  
Smart City ◽  
Laser Scanning ◽  
Near Infrared ◽  
Three Dimensional ◽  
Energy Sector ◽  
Primary Objective ◽  
Airborne Lidar ◽  
City Management ◽  
Urban Context ◽  
Research Areas

The management of an urban context in a Smart City perspective requires the development of innovative projects, with new applications in multidisciplinary research areas. They can be related to many aspects of city life and urban management: fuel consumption monitoring, energy efficiency issues, environment, social organization, traffic, urban transformations, etc. Geomatics, the modern discipline of gathering, storing, processing, and delivering digital spatially referenced information, can play a fundamental role in many of these areas, providing new efficient and productive methods for a precise mapping of different phenomena by traditional cartographic representation or by new methods of data visualization and manipulation (e.g. three-dimensional modelling, data fusion, etc.). The technologies involved are based on airborne or satellite remote sensing (in visible, near infrared, thermal bands), laser scanning, digital photogrammetry, satellite positioning and, first of all, appropriate sensor integration (online or offline). The aim of this work is to present and analyse some new opportunities offered by Geomatics technologies for a Smart City management, with a specific interest towards the energy sector related to buildings. Reducing consumption and CO2 emissions is a primary objective to be pursued for a sustainable development and, in this direction, an accurate knowledge of energy consumptions and waste for heating of single houses, blocks or districts is needed. A synoptic information regarding a city or a portion of a city can be acquired through sensors on board of airplanes or satellite platforms, operating in the thermal band. A problem to be investigated at the scale A problem to be investigated at the scale of the whole urban context is the Urban Heat Island (UHI), a phenomenon known and studied in the last decades. UHI is related not only to sensible heat released by anthropic activities, but also to land use variations and evapotranspiration reduction. The availability of thermal satellite sensors is fundamental to carry out multi-temporal studies in order to evaluate the dynamic behaviour of the UHI for a city. Working with a greater detail, districts or single buildings can be analysed by specifically designed airborne surveys. The activity has been recently carried out in the EnergyCity project, developed in the framework of the Central Europe programme established by UE. As demonstrated by the project, such data can be successfully integrated in a GIS storing all relevant data about buildings and energy supply, in order to create a powerful geospatial database for a Decision Support System assisting to reduce energy losses and CO2 emissions. Today, aerial thermal mapping could be furthermore integrated by terrestrial 3D surveys realized with Mobile Mapping Systems through multisensor platforms comprising thermal camera/s, laser scanning, GPS, inertial systems, etc. In this way the product can be a true 3D thermal model with good geometric properties, enlarging the possibilities in respect to conventional qualitative 2D images with simple colour palettes. Finally, some applications in the energy sector could benefit from the availability of a true 3D City Model, where the buildings are carefully described through three-dimensional elements. The processing of airborne LiDAR datasets for automated and semi-automated extraction of 3D buildings can provide such new generation of 3D city models.

Photon Emission Spectral Signatures of AlGaN/GaN HEMT for Functional and Reliability Analysis

2008 ◽  
Author(s):  
Arkadiusz Glowacki ◽  
Christian Boit ◽  
Richard Lossy ◽  
Joachim Würfl
Keyword(s):  
Reliability Analysis ◽  
Gate Voltage ◽  
Near Infrared ◽  
Photon Emission ◽  
Electrical Characterization ◽  
Spectral Signatures ◽  
Operating Modes ◽  
Gan Hemt ◽  
Spectrally Resolved ◽  
Performance Variations

Abstract Non-degraded and degraded AlGaN/GaN HEMT devices have been characterized electrically and investigated in various operating modes using integral and spectrally resolved photon emission (PE). In degraded devices the PE dependence on the gate voltage differs from the non-degraded devices. Various types of dependencies on the gate voltage have been identified when investigating local degradation sites. PE spectroscopy was performed at various bias conditions. For both devices broad spectra have been obtained in a wavelength regime from visible to near-infrared, including local performance variations. Signatures of the degradation have been determined in the electrical characterization, in integral PE distribution and in the PE spectrum.

scholarly journals Electromechanically reconfigurable optical nano-kirigami

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Shanshan Chen ◽  
Zhiguang Liu ◽  
Huifeng Du ◽  
Chengchun Tang ◽  
Chang-Yin Ji ◽  
...  
Keyword(s):  
Near Infrared ◽  
Large Range ◽  
Three Dimensional ◽  
High Contrast ◽  
Si Substrate ◽  
High Modulation ◽  
Gold Nanostructure ◽  
Infrared Wavelengths ◽  
On Chip ◽  
Nano Electromechanical System

AbstractKirigami, with facile and automated fashion of three-dimensional (3D) transformations, offers an unconventional approach for realizing cutting-edge optical nano-electromechanical systems. Here, we demonstrate an on-chip and electromechanically reconfigurable nano-kirigami with optical functionalities. The nano-electromechanical system is built on an Au/SiO2/Si substrate and operated via attractive electrostatic forces between the top gold nanostructure and bottom silicon substrate. Large-range nano-kirigami like 3D deformations are clearly observed and reversibly engineered, with scalable pitch size down to 0.975 μm. Broadband nonresonant and narrowband resonant optical reconfigurations are achieved at visible and near-infrared wavelengths, respectively, with a high modulation contrast up to 494%. On-chip modulation of optical helicity is further demonstrated in submicron nano-kirigami at near-infrared wavelengths. Such small-size and high-contrast reconfigurable optical nano-kirigami provides advanced methodologies and platforms for versatile on-chip manipulation of light at nanoscale.

scholarly journals Validity and reliability of smartphone applications for measurement of hip rotation, compared with three‐dimensional motion analysis

2021 ◽  
Vol 22 (1) ◽  
Author(s):  
Phob Ganokroj ◽  
Nuchanun Sompornpanich ◽  
Pichitpol Kerdsomnuek ◽  
Bavornrat Vanadurongwan ◽  
Pisit Lertwanich
Keyword(s):  
Internal Rotation ◽  
Motion Analysis ◽  
Supine Position ◽  
External Rotation ◽  
Three Dimensional ◽  
Angle Measurement ◽  
Smartphone Applications ◽  
Rater Reliability ◽  
Link Type ◽  
Hip Rotation

Abstract Background Measurement of hip rotation is a crucial clinical parameter for the identification of hip problems and the monitoring of symptoms. The objective of this study was to determine whether the use of two smartphone applications is valid and reliable for the measurement of hip rotation. Methods An experimental, cross-sectional study was undertaken to assess passive hip internal and external rotation in three positions by two examiners. The hip rotational angles were measured by a smartphone clinometer application in the sitting and prone positions, and by a smartphone compass application in the supine position; their results were compared with those of the standard, three-dimensional, motion analysis system. The validities and inter-rater and intra-rater reliabilities of the smartphone applications were evaluated. Results The study involved 24 participants. The validities were good to excellent for the internal rotation angles in all positions (ICC 0.81–0.94), good for the external rotation angles in the prone position (ICC 0.79), and fair for the sitting and supine positions (ICC 0.70–0.73). The measurement of the hip internal rotation in the supine position had the highest ICC value of 0.94 (0.91, 0.96). The two smartphone applications showed good-to-excellent intra-rater reliability, but good-to-excellent inter-rater reliability for only three of the six positions (two other positions had fair reliability, while one position demonstrated poor reliability). Conclusions The two smartphone applications have good-to-excellent validity and intra-rater reliability, but only fair-to-good inter-rater reliability for the measurement of the hip rotational angle. The most valid hip rotational position in this study was the supine IR angle measurement, while the lowest validity was the ER angle measurement in the sitting position. The smartphone application is one of the practical measurements in hip rotational angles. Trial registration Number 20181022003 at the Thai Clinical Trials Registry (http://www.clinicaltrials.in.th) which was retrospectively registered at 2018-10-18 15:30:29.

scholarly journals Dermacozine N, the First Natural Linear Pentacyclic Oxazinophenazine with UV–Vis Absorption Maxima in the Near Infrared Region, Along with Dermacozines O and P Isolated from the Mariana Trench Sediment Strain Dermacoccus abyssi MT 1.1T

Marine Drugs ◽  
2021 ◽  
Vol 19 (6) ◽  
pp. 325
Author(s):  
Bertalan Juhasz ◽  
Dawrin Pech-Puch ◽  
Jioji N. Tabudravu ◽  
Bastien Cautain ◽  
Fernando Reyes ◽  
...  
Keyword(s):  
Linear Regression ◽  
Density Functional ◽  
Near Infrared ◽  
Linear Regression Analysis ◽  
2D Nmr ◽  
Multiple Linear Regression Analysis ◽  
Infrared Region ◽  
Cellular Level ◽  
Mariana Trench ◽  
Uv Visible

Three dermacozines, dermacozines N–P (1–3), were isolated from the piezotolerant Actinomycete strain Dermacoccus abyssi MT 1.1T, which was isolated from a Mariana Trench sediment in 2006. Herein, we report the elucidation of their structures using a combination of 1D/2D NMR, LC-HRESI-MSn, UV–Visible, and IR spectroscopy. Further confirmation of the structures was achieved through the analysis of data from density functional theory (DFT)–UV–Visible spectral calculations and statistical analysis such as two tailed t-test, linear regression-, and multiple linear regression analysis applied to either solely experimental or to experimental and calculated 13C-NMR chemical shift data. Dermacozine N (1) bears a novel linear pentacyclic phenoxazine framework that has never been reported as a natural product. Dermacozine O (2) is a constitutional isomer of the known dermacozine F while dermacozine P (3) is 8-benzoyl-6-carbamoylphenazine-1-carboxylic acid. Dermacozine N (1) is unique among phenoxazines due to its near infrared (NIR) absorption maxima, which would make this compound an excellent candidate for research in biosensing chemistry, photodynamic therapy (PDT), opto-electronic applications, and metabolic mapping at the cellular level. Furthermore, dermacozine N (1) possesses weak cytotoxic activity against melanoma (A2058) and hepatocellular carcinoma cells (HepG2) with IC50 values of 51 and 38 μM, respectively.

scholarly journals Neural Modeling of the Distribution of Protein, Water and Gluten in Wheat Grains during Storage

2020 ◽  
Vol 12 (12) ◽  
pp. 5050
Author(s):  
Katarzyna Szwedziak ◽  
Ewa Polańczyk ◽  
Żaneta Grzywacz ◽  
Gniewko Niedbała ◽  
Wiktoria Wojtkiewicz
Keyword(s):  
Total Protein ◽  
Near Infrared ◽  
Linear Regression Analysis ◽  
Multiple Linear Regression Analysis ◽  
Quality Parameters ◽  
Neural Modeling ◽  
Infrared Spectrometry ◽  
Stored Grain ◽  
Stored Wheat

An important requirement in the grain industry is to obtain fast information on the quality of purchased and stored grain. Therefore, it is of great importance to search for innovative solutions aimed at the monitoring and fast assessment of quality parameters of stored wheat The results of the evaluation of total protein, water and gluten content by means of near infrared spectrometry are presented in the paper. Multiple linear regression analysis (MLR) and neural modeling were used to analyze the obtained results. The results obtained show no significant changes in total protein (13.13 ± 0.15), water (10.63 ± 0.16) or gluten (30.56 ± 0.54) content during storage. On the basis of the collected data, a model artificial neural network (ANN) MLP 52-6-3 was created, which, with the use of four independent features, allows us to determine changes in the content of water, protein and gluten in stored wheat. The chosen network returned good error values: learning, below 0.001; testing, 0.015; and validation, 0.008. The obtained results and their interpretation are an important element in the warehouse industry. The information obtained in this way about the state of the quality of stored grain will allow for a fast reaction in case of the threat of lowering the quality parameters of the stored grain.

The Three-Dimensional Surface Topographic Characterisation of Diamond Grinding Wheels

2010 ◽  
Vol 126-128 ◽  
pp. 690-695
Author(s):  
David Lee Butler
Keyword(s):  
Measurement Techniques ◽  
Three Dimensional ◽  
Surface Measurement ◽  
Grinding Wheel ◽  
Profile Measurement ◽  
Detailed Knowledge ◽  
Grinding Wheels ◽  
Diamond Grinding ◽  
Insight Into ◽  
Dimensional Surface

Surface measurement using three-dimensional stylus instruments is a relatively new technique that offers numerous advantages over more traditional profilometry methods. The information generated is, unlike profile measurement, less subjective and more statistical providing additional insight into the surface structure. One application of surface measurement that has encountered problems when using the profilometry method is that of grinding wheel characterisation. The wheel surface texture (topography) and the conditions under which it is generated have a profound effect upon the grinding performance as characterised by the grinding forces, power consumption, temperature, and surface integrity of components. A detailed knowledge of the nature of the topography of the grinding wheel would provide further insight into surface interactions between the wheel and workpiece as well as enabling improved control of the grinding process in general. In this paper four diamond grinding wheels of 91 and 181 micron grit size were subjected to differing dressing conditions to produce varying final wheel topographies. Three-dimensional surface measurement techniques were employed to quantitatively characterise the topographic change and provide an aerial estimation of the number of cutting grains. The results demonstrate that the techniques can distinguish between a worn and dressed wheel. In addition, the parametric values generated from the various surfaces can aid the user in determining when re-dressing is required.

Three-dimensional Force Perception of Robotic Bipolar Forceps for Brain Tumor Resection

2021 ◽  
Author(s):  
Xiu-Heng Zhang ◽  
Heng Zhang ◽  
Zhen Li ◽  
Gui-Bin Bian
Keyword(s):  
Brain Tumor ◽  
Real Time ◽  
Force Measurement ◽  
Measurement Techniques ◽  
Tumor Resection ◽  
Three Dimensional ◽  
Contact Forces ◽  
Surgical Instruments ◽  
Force Perception ◽  
Brain Tumor Resection

Abstract Three-dimensional force perception is critically important in the enhancement of human force perception to minimize brain injuries resulting from excessive forces applied by surgical instruments in robot-assisted brain tumor resection. And surgeons are not responsive enough to interpret tool-tissue interaction forces. In previous studies, various force measurement techniques have been published. In neurosurgical scenarios, there are still some drawbacks to these presented approaches to forces perception. Because of the narrow, and slim configuration of bipolar forceps, three-dimensional contact forces on forceps tips is not easy to be traced in real-time. Five fundamental acts of handling bipolar forceps are poking, opposing, pressing, opening, and closing. The first three acts independently correspond to the axial force of z, x, y. So, in this paper, typical interactions between bipolar forceps and brain tissues have been analyzed. A three-dimensional force perception technique to collect force data on bipolar forceps tips by installing three Fiber Bragg Grating Sensors (FBGs) on each prong of bipolar forceps in real-time is proposed. Experiments using a tele-neurosurgical robot were performed on an in-vitro pig brain. In the experiments, three-dimensional forces were tracked in real-time. It is possible to experience forces at a minimum of 0.01 N. The three-dimensional force perception range is 0-4 N. The calibrating resolution on x, y, and z, is 0.01, 0.03, 0.1 N, separately. According to our observation, the measurement accuracy precision is over 95%.

Multiple Ship Motion Simulation Code Correlation with Model Test Results

2017 ◽  
Author(s):  
James A. Coller ◽  
Andrew Silver ◽  
Okey Nwogu ◽  
Benjamin S.H. Connell
Keyword(s):  
Real Time ◽  
Model Test ◽  
Three Dimensional ◽  
Angle Measurement ◽  
Ship Motion ◽  
Ship Motions ◽  
Simulation Code ◽  
Forecasting System ◽  
Scale Experiment ◽  
Response Amplitude Operators

The US Nav has developed a real-time multi-ship ship motion forecasting system which combines forecast wave conditions with ship motion simulations to produce a prediction of the relative motions between two ships operating in a skin-to-skin configuration. The system utilizes two different simulation methods for predicting ship motions: MotionSim and Reduced Order Model (ROM) based on AEGIR. MotionSim is a fast three-dimensional panel method that is used to estimate the Response Amplitude Operators (RAOs) necessary for multi-ship motion predictions. The ROM works to maximize the accuracy of high fidelity ship motion prediction methods while maintaining the computational speed required for real-time forecasting. A model scale experiment was performed in 2015 on two Navy ships conventionally moored together. The predicted relative ship motions from MotionSim and ROM were compared to the model data using three different metrics: RMS (root mean square) ratio, correlation coefficient, and average angle measurement (AAM).This paper provides an overview of the two methods for predicting the multi-ship motions, a description of the model test, challenges faced during testing, and a discussion on the methodology of the evaluation and the results of each code correlation.

Sign in / Sign up

Export Citation Format

Share Document