Temperature Stability Of Plasma Polymerized Antiadhesive Coatings

1998 ◽  
Vol 544 ◽  
Author(s):  
W. Michaeli ◽  
R. Dahlmann ◽  
I. Fonteiner
Keyword(s):  
Surface Tension ◽  
Photoelectron Spectroscopy ◽  
Thermo Gravimetric Analysis ◽  
Temperature Stability ◽  
Polymer Coatings ◽  
Gravimetric Analysis ◽  
Angle Measurements ◽  
Wide Range ◽  
Contact Angle Measurements ◽  
Thermal Stability Of

AbstractBy means of microwave-assisted plasma polymerization it is possible to deposit polymer coatings on different surfaces such as plastics or metals. The surface tension can be influenced in a wide range. However, many applications require a high thermal stability of such low surface tension layers. Therefore, the influence of variations of the process parameters on temperature stability of such layers is examined. The produced layers were studied regarding their chemical and physical characteristics under temperature influence by means of contact angle measurements, xray photoelectron spectroscopy (XPS), thermo gravimetric analysis (TGA) combined with Fouriertransformed infrared spectroscopy (FTIR). Fluorine containing monomers offer good perspectives. Up to temperatures of approx. 200°C the antiadhesivity of these coatings is adjustable to values close to those of poly(tetrafluoroethylene) (PTFE).

MECHANICAL PROPERTIES OF BAMBOO POWDER REINFORCED ETHYLENE PROPYLENE DIENE MONOMER (EPDM) COMPOSITES: EFFECT OF FILLER LOADING AND PARTICLE SIZE

2014 ◽  
Vol 6 (2) ◽  
pp. 1122-1134 ◽  
Author(s):  
Mokhtar Hemdan Abd El-Salam
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Particle Size ◽  
Internal Friction ◽  
Thermo Gravimetric Analysis ◽  
Filler Loading ◽  
Gravimetric Analysis ◽  
Wide Range ◽  
Bamboo Powder ◽  
Thermal Stability Of

Due to the light weight, high specific strength and non hazardous nature of bamboo fiber, it is preferred over synthetic fibers in composite materials for a wide range of applications such as automotive industry and including household sectors. As was noticed, little attention has been given to the effect of bamboo powder on the mechanical properties of rubber composites. Hence, an attempt has been made in this paper to the study the effect of loading and particle size of bamboo powder on the mechanical properties of EPDM composites. Thermo-gravimetric analysis (TGA) was carried out to study the thermal stability of composites. Results indicated that the thermal stability of EPDM was further improved with increasing in bamboo loading and decreasing in particle size. The stress- strain curves of the composites were studied and fitted according toOgden’s model. Mechanical parameters for the studied composites were improved with increasing bamboo loading. Besides, properties such as rupture stress, and internal friction were found to be maximum for composites containing certain content of bamboo powder, depending upon its particle size. Moreover, composites containing the smallest particle size of powder, at all levels of bamboo loading, showed mechanical properties superior to all other composites. From the dynamic mechanical measurements, the dynamic modulus, internal friction, and thermal diffusivity were calculated. The observed variations were explained in view of the role played by both the loading level and the particle size of bamboo powder. These findings were supported by scanning electron microscopy (SEM) micrographs.

scholarly journals Preparation and Characterization of Chitosan/Agar Blended Films: Part 2. Thermal, Mechanical, and Surface Properties

2012 ◽  
Vol 9 (2) ◽  
pp. 510-516 ◽  
Author(s):  
Esam A. Elhefian ◽  
Mohamed Mahmoud Nasef ◽  
Abdul Hamid Yahaya
Keyword(s):  
Gravimetric Analysis ◽  
Thermal Gravimetric ◽  
Water Contact ◽  
Elongation At Break ◽  
Angle Measurements ◽  
Static Water Contact Angle ◽  
Contact Angle Measurements ◽  
Static Water ◽  
Thermal Stability Of

Chitosan/agar (CS/AG) films were prepared by blending different proportions of chitosan and agar (considering chitosan as the major component) in solution forms. The thermal stability of the blended films was studied using thermal gravimetric analysis (TGA). It was revealed that chitosan and agar form a compatible blend. Studying the mechanical properties of the films showed a decrease in the tensile strength and elongation at break with increasing agar content. Blending of agar with chitosan at all proportions was found to form hydrogel films with enhanced swelling compared to the pure chitosan one. Static water contact angle measurements confirmed the increasing affinity of the blended films towards water suggesting that blending of agar with chitosan improves the wettability of the obtained films.

scholarly journals Development of Nervilia fordii Extract-Loaded Electrospun PVA/PVP Nanocomposite for Antioxidant Packaging

Foods ◽  
2021 ◽  
Vol 10 (8) ◽  
pp. 1728
Author(s):  
Peng Wen ◽  
Teng-Gen Hu ◽  
Yan Wen ◽  
Ke-Er Li ◽  
Wei-Peng Qiu ◽  
...  
Keyword(s):  
Food Packaging ◽  
Thermo Gravimetric Analysis ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
Poly Vinyl Alcohol ◽  
Total Phenolic ◽  
Gravimetric Analysis ◽  
Thermo Gravimetric ◽  
Phenolic And Flavonoid ◽  
Thermal Stability Of

An ethyl acetate extract from of Nervilia fordii (NFE) with considerable suppression activity on lipid peroxidation (LPO) was first obtained with total phenolic and flavonoid contents and anti-LPO activity (IC50) of 86.67 ± 2.5 mg GAE/g sample, 334.56 ± 4.7 mg RE/g extract and 0.307 mg/mL, respectively. In order to improve its stability and expand its application in antioxidant packaging, the nano-encapsulation of NFE within poly(vinyl alcohol) (PVA) and polyvinyl(pyrrolidone) (PVP) bio-composite film was then successfully developed using electrospinning. SEM analysis revealed that the NFE-loaded fibers exhibited similar morphology to the neat PVA/PVP fibers with a bead-free and smooth morphology. The encapsulation efficiency of NFE was higher than 90% and the encapsulated NFE still retained its antioxidant capacity. Fourier transform infrared spectroscopy (FTIR) and X-ray powder diffraction (XRD) analysis confirmed the successful encapsulation of NFE into fibers and their compatibility, and the thermal stability of which was also improved due to the intermolecular interaction demonstrated by thermo gravimetric analysis (TGA). The ability to preserve the fish oil’s oxidation and extend its shelf-life was also demonstrated, suggesting the obtained PVA/PVP/NFE fiber mat has the potential as a promising antioxidant food packaging material.

scholarly journals Preparation and structure of SiOCN fibres derived from cyclic silazane/poly-acrylic acid hybrid precursor

2019 ◽  
Vol 6 (10) ◽  
pp. 190690
Author(s):  
Zhongkan Ren ◽  
Christel Gervais ◽  
Gurpreet Singh
Keyword(s):  
Acrylic Acid ◽  
Photoelectron Spectroscopy ◽  
Thermo Gravimetric Analysis ◽  
Ceramic Matrix Composite ◽  
Linear Structure ◽  
Cost Effective ◽  
Gravimetric Analysis ◽  
Low Viscosity ◽  
Hybrid Precursor ◽  
Poly Acrylic Acid

Ceramic matrix composite (CMC) materials have been considered a desired solution for lightweight and high-temperature applications. Simultaneously, among all different CMC reinforcements, polymer-derived ceramic (PDC) fibres have gained attention for the intrinsic thermal stability and mechanical strength with simple and cost-effective synthesis techniques. Here, carbon-rich SiOCN fibres were synthesized via hand-drawing and polymer pyrolysis of a hybrid precursor of 1,3,5,7-tetramethyl-1,3,5,7-tetravinylcyclotetrasilazane (TTCSZ) and poly-acrylic acid (PAA). The type of silazane reported in this work is considered as a major precursor for SiCN; however, it is unspinnable, due to its unfavourable physical properties (low viscosity) and chemical structure (cyclic rather than linear structure). The introduction of PAA to TTCSZ to create a hybrid precursor remarkably improved the spinnability of the silazane and should be widely applicable to other unspinnable PDC pre-ceramic polymers. Investigations on the structural and compositional development of the fibres were mainly conducted via Raman spectroscopy, Fourier-transform infrared spectroscopy, scanning electron microscopy, X-ray photoelectron spectroscopy, nuclear magnetic resonance and thermo-gravimetric analysis to determine spinnability, free carbon content, cross-linking and pyrolysis behaviour of the fibres, respectively.

scholarly journals Green Bio-Assisted Synthesis, Characterization and Biological Evaluation of Biocompatible ZnO NPs Synthesized from Different Tissues of Milk Thistle (Silybum marianum)

Nanomaterials ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 1171 ◽  
Author(s):  
Bilal Haider Abbasi ◽  
Muzamil Shah ◽  
Syed Salman Hashmi ◽  
Munazza Nazir ◽  
Sania Naz ◽  
...  
Keyword(s):  
Thermo Gravimetric Analysis ◽  
Radical Scavenging ◽  
Biological Evaluation ◽  
Seed Extract ◽  
Wild Plant ◽  
Gravimetric Analysis ◽  
Silybum Marianum ◽  
Zno Nps ◽  
Wide Range ◽  
Different Tissues

The purpose of the current study was green synthesis of ZnO-nanoparticles (NPs) from different tissues of Silybum marianum (L.) Gaernt. (i.e., seeds, wild plant, in vitro derived plantlets and callus cultures) followed by extensive characterization and evaluation of their biological potency. ZnO-NPs thus synthesized were subjected to characterization using standard techniques such as XRD, FTIR and SEM. Thermal stability of synthesized NPs was also evaluated using thermo-gravimetric analysis. Highly stable crystalline NPs with size ranging between 30.8 and 46.0 nm were obtained from different tissues of S. marianum. These NPs have revealed a wide range of biological applications showing antioxidant, moderate α-amylase inhibitor, antibacterial and cytotoxic potencies. The highest antibacterial activity (20 ± 0.98 mm) was shown by seed extract-mediated ZnO NPs against Staphylococcus aureus (ATCC-6538). Seed extract-mediated ZnO NPs also showed the most potent antioxidant activity (27.7 ± 0.9 µgAAE/mg, 23.8 ± 0.7 µgAAE/mg and 12.7 ± 1.9% total antioxidant capacity (TAC), total reducing power (TRP) and DPPH-free radical scavenging assay (FRSA), respectively). All of the synthesized ZnO NPs also showed cytotoxic activity against the hepato-cellular carcinoma (HepG2) human cells. Interestingly, these ZnO NPs were also highly biocompatible, as evidenced by the brine shrimp lethality and human red blood cells hemolytic assays. Among all of the NPs synthesized and used, the effect of seed extract-mediated NPs was found to be most promising for future applications.

scholarly journals 3D Printed Silicone Meniscus Implants: Influence of the 3D Printing Process on Properties of Silicone Implants

Polymers ◽  
2020 ◽  
Vol 12 (9) ◽  
pp. 2136
Author(s):  
Eric Luis ◽  
Houwen Matthew Pan ◽  
Anil Kumar Bastola ◽  
Ram Bajpai ◽  
Swee Leong Sing ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Weight Bearing ◽  
Thermo Gravimetric Analysis ◽  
Silicone Implants ◽  
Osteoarthritis Of The Knee ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Hydrogel Scaffolds ◽  
Custom Made ◽  
3D Printed

Osteoarthritis of the knee with meniscal pathologies is a severe meniscal pathology suffered by the aging population worldwide. However, conventional meniscal substitutes are not 3D-printable and lack the customizability of 3D printed implants and are not mechanically robust enough for human implantation. Similarly, 3D printed hydrogel scaffolds suffer from drawbacks of being mechanically weak and as a result patients are unable to execute immediate post-surgical weight-bearing ambulation and rehabilitation. To solve this problem, we have developed a 3D silicone meniscus implant which is (1) cytocompatible, (2) resistant to cyclic loading and mechanically similar to native meniscus, and (3) directly 3D printable. The main focus of this study is to determine whether the purity, composition, structure, dimensions and mechanical properties of silicone implants are affected by the use of a custom-made in-house 3D-printer. We have used the phosphate buffer saline (PBS) absorption test, Fourier transform infrared (FTIR) spectroscopy, surface profilometry, thermo-gravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS), differential scanning calorimetry (DSC), and scanning electron microscopy (SEM) to effectively assess and compare material properties between molded and 3D printed silicone samples.

Effect of Alkali and Silane Treatment on the Thermal Stability of Hemp Fibers as Reinforcement in Composite Structures

2011 ◽  
Vol 415-417 ◽  
pp. 666-670 ◽  
Author(s):  
Na Lu ◽  
Shubhashini Oza ◽  
Ian Ferguson
Keyword(s):  
Thermal Stability ◽  
Composite Structures ◽  
Natural Fiber ◽  
Alkali Treatment ◽  
Thermo Gravimetric Analysis ◽  
Natural Fibers ◽  
Gravimetric Analysis ◽  
Silane Treatment ◽  
Hemp Fibers ◽  
Thermal Stability Of

Natural fiber reinforced composites are being used as reinforcement material in composite system due to their positive environmental benefits. Added to that, natural fibers offer advantages such as low density, low cost, good toughness, high specific strength, relatively non-abrasive and wide availability. However, the low thermal stability of natural fibers is one of the major challenges to increase their use as reinforcing component. In this study, a thorough investigation has been done to compare the effect of two chemical treatment methods on the thermal stability of hemp fibers. 5wt% sodium hydroxide and 5wt% triethoxyvinylsilane was used for the treatment of hemp fibers. Fourier transform infrared spectroscopy, scanning electron microscopy and thermo gravimetric analysis were used for characterization of untreated and treated fiber. The results indicated that 24 hours alkali treatment and 3 hours silane treatment time enhanced the thermal stability of the hemp fiber. However, alkali treatment shows better improvement compared to silane treatment.

scholarly journals Effect of Sr2TiMnO6 fillers on mechanical, dielectric and thermal behaviour of PMMA polymer

2015 ◽  
Vol 05 (03) ◽  
pp. 1550018 ◽  
Author(s):  
P. Thomas ◽  
B. S. Dakshayini ◽  
H. S. Kushwaha ◽  
Rahul Vaish
Keyword(s):  
Coefficient Of Thermal Expansion ◽  
Thermo Gravimetric Analysis ◽  
Mechanical Analysis ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Melt Mixing ◽  
Transition Formula ◽  
Thermal Stability Of ◽  
Pmma Polymer

Composites of poly(methyl methacrylate) (PMMA) and [Formula: see text] (STMO) were fabricated via melt mixing followed by hot pressing technique. These were characterized using X-ray diffraction (XRD), thermo gravimetric analysis (TGA), differential scanning calorimetry (DSC), thermo mechanical analysis (TMA) and impedance analyser for their structural, thermal and dielectric properties. The coefficient of thermal expansion (CTE) was measured between 40°C and 100°C for pure PMMA is 115.2 ppm/°C, which was decreased to 78.58 ppm/°C when the STMO content was increased to 50 wt.% in PMMA. There was no difference in the glass transition ([Formula: see text]) temperature of the PMMA polymer and their composites. However, the FTIR analysis indicated possible interaction between the PMMA and STMO. The density and the hardness were increased as the STMO content increased in the PMMA matrix. Permittivity was found to be as high as 30.9 at 100 Hz for the PMMA+STMO-50 wt.% composites, indicating the possibility of using these materials for capacitor applications. The thermal stability of polymer was enhanced by incorporation of STMO fillers.

scholarly journals Amphiphobic Nanostructured Coatings for Industrial Applications

Materials ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 787 ◽  
Author(s):  
Federico Veronesi ◽  
Giulio Boveri ◽  
Mariarosa Raimondo
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Photoelectron Spectroscopy ◽  
Contact Angle Hysteresis ◽  
Contact Angles ◽  
Friction Reduction ◽  
Hybrid Coatings ◽  
Wetting Behavior ◽  
Wide Range ◽  
Solid Liquid

The search for surfaces with non-wetting behavior towards water and low-surface tension liquids affects a wide range of industries. Surface wetting is regulated by morphological and chemical features interacting with liquid phases under different ambient conditions. Most of the approaches to the fabrication of liquid-repellent surfaces are inspired by living organisms and require the fabrication of hierarchically organized structures, coupled with low surface energy chemical composition. This paper deals with the design of amphiphobic metals (AM) and alloys by deposition of nano-oxides suspensions in alcoholic or aqueous media, coupled with perfluorinated compounds and optional infused lubricant liquids resulting in, respectively, solid–liquid–air and solid–liquid–liquid working interfaces. Nanostructured organic/inorganic hybrid coatings with contact angles against water above 170°, contact angle with n-hexadecane (surface tension γ = 27 mN/m at 20 °C) in the 140–150° range and contact angle hysteresis lower than 5° have been produced. A full characterization of surface chemistry has been undertaken by X-ray photoelectron spectroscopy (XPS) analyses, while field-emission scanning electron microscope (FE-SEM) observations allowed the estimation of coatings thicknesses (300–400 nm) and their morphological features. The durability of fabricated amphiphobic surfaces was also assessed with a wide range of tests that showed their remarkable resistance to chemically aggressive environments, mechanical stresses and ultraviolet (UV) radiation. Moreover, this work analyzes the behavior of amphiphobic surfaces in terms of anti-soiling, snow-repellent and friction-reduction properties—all originated from their non-wetting behavior. The achieved results make AM materials viable solutions to be applied in different sectors answering several and pressing technical needs.

Effect of 172-nm UV irradiation on polyimide and its application in surface modification by grafting

2020 ◽  
Vol 32 (7) ◽  
pp. 761-774
Author(s):  
Lopamudra Das ◽  
John C Poutsma ◽  
Michael J Kelley
Keyword(s):  
Uv Irradiation ◽  
Photoelectron Spectroscopy ◽  
Secondary Ion Mass Spectrometry ◽  
Mechanical Stability ◽  
Uv Light ◽  
Force Microscopy ◽  
Angle Measurements ◽  
Wide Range ◽  
Grafting Reactions ◽  
Sample Position

Polyimides (PIs) have a wide range of industrial and scientific applications due to their excellent thermal and mechanical stability and chemical resistance. Their response to ultraviolet (UV) irradiation is of further interest in high-value applications such as spacecraft technology and electronics packaging. In this work, we investigated the effect of 172-nm UV xenon excimer lamp irradiation on samples of pyromellitimido-oxydianiline (PMDA-ODA) commercial films in the absence of oxygen. The average irradiance received at the sample position was 90 mW/cm2, and the total radiation dosage varied from 0 to 64 J/cm2. X-Ray photoelectron spectroscopy, time-of-flight-secondary ion mass spectrometry, atomic force microscopy, and contact angle measurements were used to characterize the effect. Calculated UV-visible spectroscopy absorption spectra were obtained using the ZINDO//B3LYP/3-21G method to give an indication of which orbitals are involved in the transitions near 172 nm. The reactivity of the different UV-treated PI samples toward nitrogen-borne heptafluorodecene vapor was then investigated using the above techniques. Grafting reactions occurred on the surface of the photochemically activated polymer. This study explored the potential for modification of PI surfaces using UV-light-assisted grafting to impart valuable functionalities.

Sign in / Sign up

Export Citation Format

Share Document