scholarly journals Zearalenone Removal by Using Banana Peel as an Adsorbent

2020 ◽  
Vol 21 (2) ◽  
pp. 271-279
Author(s):  
Z. H. Shar
Keyword(s):  
Fourier Transforms ◽  
Animal Feed ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Banana Peel ◽  
Equilibration Time ◽  
Reproductive Disorders ◽  
Fusarium Toxin ◽  
Fourier Transforms Infrared Spectroscopy

Zearalenone (ZEA) is the most occurring Fusarium toxin in animal feed causing reproductive disorders and results in severe economical losses. A renewable bio adsorbent sourced from banana peel was tested for in vitro removal of ZEA from liquid mediums at different pH values. Efficacy of banana peel to sequester ZEA was evaluated by varying its pH, adsorbent dosage, equilibration time and quantified by using UHPLC-MS/MS. Adsorption was found to be efficient and completed in fifteen minutes with highest adsorption at alkaline pH (9). The adsorption and desorption studies have demonstrated the adsorption was strong enough to sustain the pH changes (3-9). Fourier transforms infrared spectroscopy (FTIR) and scanning electron microscope (SEM) was used to characterize the surface of bio sorbent to explain the mechanism of adsorption. Langmuir and Freundlich isotherm was found to be best fitted model with maximum monolayer capacity (Q0) 8 ng/mg. The results of this study suggested that dried banana peel may be an effective low cost decontamination method to be incorporated in animal feed.

scholarly journals Engineering of Calcium Alginate- PANI@Sawdust Wood hydrogel Bio-beads for the Removal of the Sulfonate Groups-Containing Orange G dye from Aqueous Solution

2021 ◽  
Author(s):  
ABDELAZIZ IMGHARN ◽  
Nouh Aarab ◽  
Abdelghani Hsini ◽  
Yassine Naciri ◽  
Mohammed Elhoudi ◽  
...  
Keyword(s):  
Calcium Alginate ◽  
Fourier Transforms ◽  
Low Cost ◽  
Aqueous Media ◽  
Freundlich Isotherm ◽  
Batch Tests ◽  
Orange G ◽  
Ft Ir ◽  
Interfering Ions ◽  
Ft Ir Spectroscopy

Abstract The aim of this work is to investigate the adsorption performance of orange G (OG) dye from aqueous solutions employing PANI@sawdust biocomposite enrobed by calcium-alginate biobeads (Alg-PANI@SD). The as-prepared adsorbent was characterized by scanning-electron-microscopy (SEM), X-ray energy dispersive spectroscopy (EDS) and Fourier transforms infrared (FT-IR) spectroscopy, and used to remove Orange G dye from water. batch tests were performed as a function of adsorbent dosage, pH, contact time, interfering ions and initial OG dye concentration. Experimental results show that the kinetic model of pseudo-first-order (PFO) and Freundlich isotherm provided a good fitting of the whole experimental data. The results revealed that the as-prepared tricomposite Alg-PANI@SD, has the potential to be applied as a low-cost adsorbent for the adsorption of OG dye from aqueous media.

scholarly journals Effect of Polymers nature and Stirring Speeds on Physicochemical Properties and the Controlled Release of Allopurinol-loaded Microspheres

2021 ◽  
Vol 66 (1) ◽  
Author(s):  
Karima Badis ◽  
Haouaria Merine ◽  
Youssef Ramli ◽  
OumCheikh Larbi ◽  
Cherifa Hakima Memou
Keyword(s):  
Fourier Transforms ◽  
Release Kinetics ◽  
Drug Loading ◽  
In Vitro Release ◽  
Release Mechanism ◽  
Release Studies ◽  
Fourier Transforms Infrared Spectroscopy ◽  
The Mean ◽  
Solvent Evaporation Process

Abstract. Allopurinol is an antigout drug therapy, commonly used in the treatment of chronic gout or hyperuricaemia associated with treatment of diuretic conditions. In the present study, new formulations based on Allopurinol, have been prepared with the microencapsulation by solvent evaporation process. Microspheres were prepared using pure Allopurinol and polymeric matrices (ethylcellulose EC, poly (ε-caprolactone) PCL, β-cyclodextrin CD and hydroxypropylmethylcellulose HPMC) at different compositions and stirring speeds to investigate the effect of these parameters on loading efficiency and drug release kinetics. The formulations produced were characterized by various methods : Fourier transforms infrared spectroscopy (FTIR), X-ray powder diffractometry, optical microscopy, surface morphology by scanning electron microscopy (SEM) and drug loading, as well as in vitro release studies in the simulated stomach tract. Depending on the stirring speed and the composition of the microparticles, the active ingredient loading is in a range from 10.46 ± 1.45 to 46.40 ± 0.5%. The microspheres are spherical and the mean Sauter diameter (d32) of the microparticles obtained is smaller and is in the range of 47.71 to 151.01 µm. Different release profiles were obtained and show that the release rate is strongly influenced by the characteristics of the microparticles ; namely, the stirring rates and the composition of the microparticles. The release mechanism was identified by modelling using Higuchi and Korsmeyer-Peppas models.   Resumen. Alopurinol es una droga terapéutica para tratar la gota, y se utiliza en el tratamiento de gota crónica o hiperuricemia asociada con el tratamiento de condiciones diuréticas. En este estudio, nuevas formulaciones basadas en Alopurinol se prepararon mediante microencapsulación por el proceso de evaporación de disolvente. Microesferas se prepararon usando Alopurinol puro y diferentes matrices poliméricas (etil-celulosa EC, poli(-caprolactona) PCL, β-cyclodextrina CD e hidroxipropil-metil-celulose HPMC) en diferentes composiciones y velocidades de agitación, para investigar el efecto de estos parámetros en la eficiencia de carga y en la cinética de liberación del fármaco. Las formulaciones obtenidas fueron caracterizadas por diferentes técnicas : Espectroscopía infrarroja de transformadas de Fourier (FTIR), difractometría de rayos X de polvos, microscopía óptica, morfología de superficies mediante microscopía electrónica de barrido electrónico, y la eficiencia de carga del fármaco, así como estudios de liberación in vitro en tracto estomacal simulado. Dependiendo de la velocidad de agitación y la composición de las micropartículas, la carga del ingrediente activo se encuentra en el rango de 10.46 ± 1.45 a 46.40 ± 0.5%. Las microesferas son esféricas y el diámetro medio de Sauter (d32) de las micropartículas obtenidas es menor, y se encuentra en el rango de 47.71 a 151.01 µm. Se obtuvieron diferentes perfiles de liberación y se observa que la velocidad de liberación está influenciada principalmente por las características propias de la producción de las micropartículas ; en particualr, las velocidades de agitación y las composición de las micropartículas. El mecanismo de liberación se ajusta mejor a los modelos matemáticos de Higuchi and Korsmeyer-Peppas.

scholarly journals Production of a Potentially Probiotic Product for Animal Feed and Evaluation of Some of Its Probiotic Properties

2021 ◽  
Vol 22 (18) ◽  
pp. 10004
Author(s):  
Rubén Agregán-Pérez ◽  
Elisa Alonso-González ◽  
Juan Carlos Mejuto ◽  
Nelson Pérez-Guerra
Keyword(s):  
Animal Feed ◽  
Low Cost ◽  
Skim Milk ◽  
Acetic Acid Bacteria ◽  
Probiotic Properties ◽  
The European Union ◽  
Gastrointestinal Conditions ◽  
Probiotic Product ◽  
Kefir Grains

Nowadays, probiotics have been proposed for substituting antibiotics in animal feed since the European Union banned the latter compounds in 2006 to avoid serious side effects on human health. Therefore, this work aimed to produce a probiotic product for use in animal feed by fed-batch fermentation of whey with a combination of kefir grains, AGK1, and the fermented whole milk used to activate these kefir grains. The probiotic culture obtained was characterized by high levels of biomass (8.03 g/L), total viability (3.6 × 108 CFU/mL) and antibacterial activity (28.26 Activity Units/mL). Some probiotic properties of the probiotic culture were investigated in vitro, including its survival at low pH values, under simulated gastrointestinal conditions, after freezing in skim milk at −20 °C, and in the commercial feed during storage at room temperature. The viable cells of lactic and acetic acid bacteria and yeasts exhibited higher tolerance to acidic pH and simulated gastrointestinal conditions when the cells were protected with skim milk and piglet feed, compared with washed cells. The results indicated the feasibility of producing a probiotic product at a low cost with a potential application in animal feed.

scholarly journals Production of a Potentially Probiotic Product for Animal Feed and Evaluation of Some of Its Probiotic Properties

2021 ◽  
Author(s):  
Rubén Agregán-Pérez ◽  
Elisa Alonso-González ◽  
Juan Carlos Mejuto ◽  
Nelson Pérez-Guerra
Keyword(s):  
Animal Feed ◽  
Low Cost ◽  
Skim Milk ◽  
Acetic Acid Bacteria ◽  
Probiotic Properties ◽  
The European Union ◽  
Gastrointestinal Conditions ◽  
Probiotic Product ◽  
Kefir Grains

Nowadays, probiotics has been proposed for substituting antibiotics in animal feed, since the European Union (EU) banned the latter compounds in 2006 to avoid their serious side effects on human health. Therefore, this work aimed to produce a probiotic product by fed-fermentation of whey with kefir grains for use in animal feed. The whey was fermented with a combination of kefir grains AGK1 and the free biomass present in whole milk fermented milk used to activate these kefir grains. The probiotic culture obtained was characterized with high levels of biomass, total viability and antibacterial activity. Some probiotic properties of the probiotic culture were investigated in vitro, including its survival at low pH values, under simulated gastrointestinal conditions, after freezing in skim milk at − 20 ºC, and in the commercial feed during storage at room temperature. The viable cells of lactic and acetic acid bacteria and yeasts exhibited higher tolerance to acidic pH and simulated gastrointestinal conditions when the cells were protected with skim milk and piglet feed, compared with washed cells. The results indicated the feasibility of producing a probiotic product at a low cost with a potential application in animal feed.

Observations of Frozen-Hydrated Microtubules

1990 ◽  
Vol 48 (1) ◽  
pp. 504-505
Author(s):  
D. Chrétien ◽  
D. Job ◽  
R.H. Wade
Keyword(s):  
Fourier Transforms ◽  
Structural Complexity ◽  
Image Contrast ◽  
Phase Behaviour ◽  
Experimental Conditions ◽  
Thin Sections ◽  
Surface Lattice ◽  
Cilia And Flagella ◽  
Outstanding Question

Microtubules are filamentary structures found in the cytoplasm of eukaryotic cells, where, together with actin and intermediate filaments, they form the components of the cytoskeleton. They have many functions and show various levels of structural complexity as witnessed by the singlet, doublet and triplet structures involved in the architecture of centrioles, basal bodies, cilia and flagella. The accepted microtubule model consists of a 25 nm diameter hollow tube with a wall made up of 13 paraxial protofilaments (pf). Each pf is a string of aligned tubulin dimers. Some results have suggested that the pfs follow a superhelix. To understand how microtubules function in the cell an accurate model of the surface lattice is one of the requirements. For example the 9x2 architecture of the axoneme will depend on the organisation of its component microtubules. We should also note that microtubules with different numbers of pfs have been observed in thin sections of cellular and of in-vitro material. An outstanding question is how does the surface lattice adjust to these different pf numbers?We have been using cryo-electron microscopy of frozen-hydrated samples to study in-vitro assembled microtubules. The experimental conditions are described in detail in this reference. The results obtained in conjunction with thin sections of similar specimens and with axoneme outer doublet fragments have already allowed us to characterise the image contrast of 13, 14 and 15 pf microtubules on the basis of the measured image widths, of the the image contrast symmetry and of the amplitude and phase behaviour along the equator in the computed Fourier transforms. The contrast variations along individual microtubule images can be interpreted in terms of the geometry of the microtubule surface lattice. We can extend these results and make some reasonable predictions about the probable surface lattices in the case of other pf numbers, see Table 1. Figure 1 shows observed images with which these predictions can be compared.

Natural Bioactive Compounds As Adjuvant Therapy For Hepatitis C Infection

2020 ◽  
Vol 16 ◽  
Author(s):  
Moema S. Santana ◽  
Rute Lopes ◽  
Isabela H. Peron ◽  
Carla R. Cruz ◽  
Ana M. M. Gaspar ◽  
...  
Keyword(s):  
Hepatitis C ◽  
Bioactive Compounds ◽  
Low Cost ◽  
Chemical Diversity ◽  
Acute Hepatitis C ◽  
Hepatitis C Infection ◽  
Middle Income ◽  
Broad Perspective ◽  
Cost Of Production

Background: Hepatitis C virus infection is a significant global health burden, which causes acute or chronic hepatitis. The acute hepatitis C is generally asymptomatic and progresses to cure, while persistent infection can progress to chronic liver disease and extrahepatic manifestations. Standard treatment is expensive, poorly tolerated, and has variable sustained virologic responses amongst the different viral genotypes. New therapies involve direct acting antivirals; however, it is also very expensive and may not be accessible for all patients worldwide. In order to provide a complementary approach to the already existing therapies, natural bioactive compounds are investigated as to their several biologic activities, such as direct antiviral properties against hepatitis C, and effects on mitigating chronic progression of the disease, which includes hepatoprotective, antioxidant, anticarcinogenic and anti-inflammatory activities; additionally, these compounds present advantages, as chemical diversity, low cost of production and milder or inexistent side effects. Objective: To present a broad perspective on hepatitis C infection, the chronic disease, and natural compounds with promising anti-HCV activity. Methods: This review consists of a systematic review study about the natural bioactive compounds as a potential therapy for hepatitis C infection. Results: The quest for natural products have yielded compounds with biologic activity, including viral replication inhibition in vitro, demonstrating antiviral activity against hepatitis C. Conclusion: One of the greatest advantages of using natural molecules from plant extracts is the low cost of production, not requiring chemical synthesis, which can lead to less expensive therapies available to low and middle-income countries.

scholarly journals Generation of High-Yield, Functional Oligodendrocytes from a c-myc Immortalized Neural Cell Line, Endowed with Staminal Properties

2021 ◽  
Vol 22 (3) ◽  
pp. 1124
Author(s):  
Mafalda Giovanna Reccia ◽  
Floriana Volpicelli ◽  
Eirkiur Benedikz ◽  
Åsa Fex Svenningsen ◽  
Luca Colucci-D’Amato
Keyword(s):  
Cell Line ◽  
Low Cost ◽  
Neural Cell ◽  
New Drugs ◽  
High Yield ◽  
Time Saving ◽  
Interacting Protein ◽  
Neuronal Marker ◽  
Differentiation Status

Neural stem cells represent a powerful tool to study molecules involved in pathophysiology of Nervous System and to discover new drugs. Although they can be cultured and expanded in vitro as a primary culture, their use is hampered by their heterogeneity and by the cost and time needed for their preparation. Here we report that mes-c-myc A1 cells (A1), a neural cell line, is endowed with staminal properties. Undifferentiated/proliferating and differentiated/non-proliferating A1 cells are able to generate neurospheres (Ns) in which gene expression parallels the original differentiation status. In fact, Ns derived from undifferentiated A1 cells express higher levels of Nestin, Kruppel-like factor 4 (Klf4) and glial fibrillary protein (GFAP), markers of stemness, while those obtained from differentiated A1 cells show higher levels of the neuronal marker beta III tubulin. Interestingly, Ns differentiation, by Epidermal Growth Factors (EGF) and Fibroblast Growth Factor 2 (bFGF) withdrawal, generates oligodendrocytes at high-yield as shown by the expression of markers, Galactosylceramidase (Gal-C) Neuron-Glial antigen 2 (NG2), Receptor-Interacting Protein (RIP) and Myelin Basic Protein (MBP). Finally, upon co-culture, Ns-A1-derived oligodendrocytes cause a redistribution of contactin-associated protein (Caspr/paranodin) protein on neuronal cells, as primary oligodendrocytes cultures, suggesting that they are able to form compact myelin. Thus, Ns-A1-derived oligodendrocytes may represent a time-saving and low-cost tool to study the pathophysiology of oligodendrocytes and to test new drugs.

scholarly journals Designing of an Advanced Compression Bioreactor with an Implementation of a Low-Cost Controlling System Connected to a Mobile Application

Processes ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 915
Author(s):  
Gözde Dursun ◽  
Muhammad Umer ◽  
Bernd Markert ◽  
Marcus Stoffel
Keyword(s):  
Mobile Application ◽  
Low Cost ◽  
Experimental Information ◽  
Raspberry Pi ◽  
Tissue Constructs ◽  
Cost Controlling ◽  
Controlling System ◽  
And Control ◽  
Tissue Models

(1) Background: Bioreactors mimic the natural environment of cells and tissues by providing a controlled micro-environment. However, their design is often expensive and complex. Herein, we have introduced the development of a low-cost compression bioreactor which enables the application of different mechanical stimulation regimes to in vitro tissue models and provides the information of applied stress and strain in real-time. (2) Methods: The compression bioreactor is designed using a mini-computer called Raspberry Pi, which is programmed to apply compressive deformation at various strains and frequencies, as well as to measure the force applied to the tissue constructs. Besides this, we have developed a mobile application connected to the bioreactor software to monitor, command, and control experiments via mobile devices. (3) Results: Cell viability results indicate that the newly designed compression bioreactor supports cell cultivation in a sterile environment without any contamination. The developed bioreactor software plots the experimental data of dynamic mechanical loading in a long-term manner, as well as stores them for further data processing. Following in vitro uniaxial compression conditioning of 3D in vitro cartilage models, chondrocyte cell migration was altered positively compared to static cultures. (4) Conclusion: The developed compression bioreactor can support the in vitro tissue model cultivation and monitor the experimental information with a low-cost controlling system and via mobile application. The highly customizable mold inside the cultivation chamber is a significant approach to solve the limited customization capability of the traditional bioreactors. Most importantly, the compression bioreactor prevents operator- and system-dependent variability between experiments by enabling a dynamic culture in a large volume for multiple numbers of in vitro tissue constructs.

scholarly journals Light Cross-Linkable Marine Collagen for Coaxial Printing of a 3D Model of Neuromuscular Junction Formation

Biomedicines ◽  
2020 ◽  
Vol 9 (1) ◽  
pp. 16
Author(s):  
Borja Sanz ◽  
Ane Albillos Sanchez ◽  
Bonnie Tangey ◽  
Kerry Gilmore ◽  
Zhilian Yue ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Neuromuscular Junction ◽  
Disease Transmission ◽  
Low Cost ◽  
Attractive Alternative ◽  
Waste Products ◽  
Environmentally Sustainable ◽  
Zoonotic Disease Transmission ◽  
And Migration

Collagen is a major component of the extracellular matrix (ECM) that modulates cell adhesion, growth, and migration, and has been utilised in tissue engineering applications. However, the common terrestrial sources of collagen carry the risk of zoonotic disease transmission and there are religious barriers to the use of bovine and porcine products in many cultures. Marine based collagens offer an attractive alternative and have so far been under-utilized for use as biomaterials for tissue engineering. Marine collagen can be extracted from fish waste products, therefore industry by-products offer an economical and environmentally sustainable source of collagen. In a handful of studies, marine collagen has successfully been methacrylated to form collagen methacrylate (ColMA). Our work included the extraction, characterization and methacrylation of Red Snapper collagen, optimisation of conditions for neural cell seeding and encapsulation using the unmodified collagen, thermally cross-linked, and the methacrylated collagen with UV-induced cross-linking. Finally, the 3D co-axial printing of neural and skeletal muscle cell cultures as a model for neuromuscular junction (NMJ) formation was investigated. Overall, the results of this study show great potential for a novel NMJ in vitro 3D bioprinted model that, with further development, could provide a low-cost, customizable, scalable and quick-to-print platform for drug screening and to study neuromuscular junction physiology and pathogenesis.

scholarly journals Fabrication, Characterization and In Vitro Cytotoxicity of Mesoporous β-Tricalcium Phosphate Using the Spray Drying Method

Crystals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 252
Author(s):  
Henni Setia Ningsih ◽  
Leonhard Tannesia ◽  
Hsiang-Ho Chen ◽  
Shao-Ju Shih
Keyword(s):  
Spray Drying ◽  
Tricalcium Phosphate ◽  
Low Cost ◽  
In Vitro Cytotoxicity ◽  
Formation Mechanisms ◽  
Synthesis Methods ◽  
Average Pore ◽  
Calcination Temperatures ◽  
Future Demands

Mesoporous beta tricalcium phosphate (β-TCP) has recently attracted significant interest as an artificial bone tissue in orthopedics. However, a scalable process is required to meet future demands. Spray drying is one of the potential synthesis methods owing to its low cost and scalable production. In this study, various mesoporous β-TCP powders were calcined in the range of 800 to 1100 °C, with particle sizes ranging from ~0.3 to ~1.8 μm, specific surface areas from ~16 to ~64 m2/g, and average pore sizes of 3 nm. Except for the 800 °C calcined powder, the other β-TCP powders (calcination temperatures of 900, 1000, and 1100 °C) exhibited no cytotoxicity. These results indicate that spray-dried mesoporous β-TCP powders were obtained. Finally, the corresponding formation mechanisms are discussed.

Sign in / Sign up

Export Citation Format

Share Document