scholarly journals Modulus, Strength and Cytotoxicity of PMMA-Silica Nanocomposites

Coatings ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 583 ◽  
Author(s):  
Sebastian Balos ◽  
Tatjana Puskar ◽  
Michal Potran ◽  
Bojana Milekic ◽  
Daniela Djurovic Koprivica ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Adverse Effect ◽  
Elastic Moduli ◽  
Dental Materials ◽  
Nanocomposite Materials ◽  
The Other ◽  
Cytotoxic Potential ◽  
Silica Nanocomposites ◽  
Mrc5 Cell ◽  
Nanoparticle Content

Key advantages of Poly(methyl methacrylate)—PMMA for denture application are related to aesthetics and biocompatibility, while its main deficiency is related to mechanical properties. To address this issue, SiO2 nanoparticle reinforcement was proposed, containing 0 to 5% nanosilica, to form nanocomposite materials. Flexural strengths and elastic moduli were determined and correlated to nominal nanoparticle content and zeta potential of the liquid phase nanoparticle solutions. Another issue is the biocompatibility, which was determined in terms of cytotoxicity, using L929 and MRC5 cell lines. The addition of nanoparticle was proved to be beneficial for increasing flexural strength and modulus, causing a significant increase in both strength and moduli. On the other hand, the formation of agglomerates was noted, particularly at higher nanoparticle loadings, affecting mechanical properties. The addition of nanosilica had an adverse effect on the cytotoxicity, increasing it above the level present in unmodified specimens. Cytotoxic potential was on the acceptable level for specimens with up to 2% nanosilica. Consequently, nanosilica proved to be an effective and biocompatible means of increasing the resistance of dental materials.

scholarly journals Influence of Vibrations During Crystallization on Mechanical Properties and Porosity of EN AC-AlSi17 Alloy

2013 ◽  
Vol 13 (1) ◽  
pp. 5-18 ◽  
Author(s):  
T. Ciućka
Keyword(s):  
Mechanical Properties ◽  
Adverse Effect ◽  
Tilt Angle ◽  
The Other ◽  
Strength Tests ◽  
New Ideas ◽  
Machining Operations ◽  
Technology Of Production

Abstract Today’s industry aims at such situation, where number of defective products, so called defects shall approach to zero. Therefore, one introduces a various changes in technology of production, introduces improvements which would help in accomplishment of this objective. Another important factor is introduction of different type of testing, which shall help in assessment which factor has significant effect on quantity of rejects, and which one could be neglected. Existence of casting rejects is unavoidable; therefore a new ideas, technologies and innovations are necessary in the entire widely understood foundry branch, in order to minimize such adverse effect. Performance of tests aimed at unequivocal determination of an effect of vibrations during crystallization on mechanical properties and porosity of the EN ACAlSi17 alloy was the objective of the present work. To do this, there were produced 36 castings from EN AC-AlSi17 alloy. All the castings underwent machining operations. Half of the casting was destined to strength tests, the other half served to determination of an effect of vibrations on porosity of the alloy. The specimens were divided into 12 groups, depending on amplitude of vibrations and tilt angle of metal mould during pouring operation.

Physical and Mechanical Properties of Tenun Pahang Fabrics using Alternative Yarns

2016 ◽  
Vol 13 (2) ◽  
pp. 67
Author(s):  
Engku Liyana Zafirah Engku Mohd Suhaimi ◽  
Jamil Salleh ◽  
Suzaini Abd Ghani ◽  
Mohamad Faizul Yahya ◽  
Mohd Rozi Ahmad
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
The Other ◽  
Silk Fabrics ◽  
Recovery Angle ◽  
Made In

An investigation on the properties of Tenun Pahang fabric performances using alternative yarns was conducted. The studies were made in order to evaluate whether the Tenun Pahang fabric could be produced economically and at the same time maintain the fabric quality. Traditional Tenun Pahang fabric uses silk for both warp and weft. For this project, two alternative yarns were used which were bamboo and modal, which were a little lower in cost compared to silk. These yarns were woven with two variations, one with the yarns as weft only while maintaining the silk warp and the other with both warp and weft using the alternative yarns. Four (4) physical testings and three (3) mechanical testings conducted on the fabric samples. The fabric samples were evaluated including weight, thickness, thread density, crease recovery angle, stiffness and drapability. The results show that modal/silk and bamboo silk fabrics are comparable in terms of stiffness and drapability, hence they have the potential to replace 100% silk Tenun Pahang.

An analysis of the transport properties and mechanical stability of rapidly solidified Al-Sb alloy

2015 ◽  
Vol 10 (2) ◽  
pp. 2663-2681
Author(s):  
Rizk El- Sayed ◽  
Mustafa Kamal ◽  
Abu-Bakr El-Bediwi ◽  
Qutaiba Rasheed Solaiman
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Melt Spinning ◽  
Elastic Moduli ◽  
Mechanical Stability ◽  
Microstructural Analysis ◽  
Alloy System ◽  
Antimony Content ◽  
The Stability ◽  
Rapidly Solidified

The structure of a series of AlSb alloys prepared by melt spinning have been studied in the as melt–spun ribbons  as a function of antimony content .The stability  of these structures has  been  related to that of the transport and mechanical properties of the alloy ribbons. Microstructural analysis was performed and it was found that only Al and AlSb phases formed for different composition.  The electrical, thermal and the stability of the mechanical properties are related indirectly through the influence of the antimony content. The results are interpreted in terms of the phase change occurring to alloy system. Electrical resistivity, thermal conductivity, elastic moduli and the values of microhardness are found to be more sensitive than the internal friction to the phase changes. 

Assessment of micro and macro nutrients in poultry feeds available in Dhaka city, Bangladesh.

2017 ◽  
Vol 1 ◽  
pp. 264
Author(s):  
Md Didarul Islam ◽  
Ashiqur Rahaman ◽  
Fahmida Jannat
Keyword(s):  
Heavy Metals ◽  
Adverse Effect ◽  
The Other ◽  
Nutrient Level ◽  
Dhaka City ◽  
Toxic Heavy Metals ◽  
High Concentration ◽  
Low Concentration ◽  
Feed Formulation ◽  
Macro Nutrients

This study was based on to determine the concentration of macro and micro nutrients as well as toxic and nontoxic heavy metals present in the chicken feed available in Dhaka city of Bangladesh. All macro nutrients, if present in the feed at high concentration have some adverse effect, at the same time if this nutrient present in the feed at low concentration this have some adverse effect too. So that this nutrient level should be maintained at a marginal level. On the other side toxic heavy metals if present in the feed at very low concentration those can contaminate the total environment of the ecosystem. In this study six brand samples (starter, grower, finisher and layer) which was collected from different renowned chicken feed formulation industry in Bangladesh. Those samples were prepared for analysis by wet ashing and then metals were determined by Atomic Absorption Spectroscopy. It was found that 27.7 to 68.4, 57.3 to 121.9, 0.21 to 4.1, 0.32 to 2.1, 0.11 to 1.58, 0.28 to 2.11 and 0.28 to 1.78 for zinc, iron, copper, mercury, cadmium, nickel and cobalt respectively. It was found that essential macro and micro nutrients were present in the feed in low concentration on the other side mercury was present in high concentration in the feed samples.

scholarly journals Generating Electricity from Natural Evaporation Using PVDF Thin Films Incorporating Nanocomposite Materials

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 585
Author(s):  
Ariel Ma ◽  
Jian Yu ◽  
William Uspal
Keyword(s):  
Thin Films ◽  
Graphene Oxide ◽  
Polyvinylidene Fluoride ◽  
Capillary Flow ◽  
Short Circuit ◽  
Current Source ◽  
Nanocomposite Materials ◽  
The Other ◽  
Pvdf Film ◽  
Ambient Conditions

Natural evaporation has recently come under consideration as a viable source of renewable energy. Demonstrations of the validity of the concept have been reported for devices incorporating carbon-based nanocomposite materials. In this study, we investigated the possibility of using polymer thin films to generate electricity from natural evaporation. We considered a polymeric system based on polyvinylidene fluoride (PVDF). Porous PVDF films were created by incorporating a variety of nanocomposite materials into the polymer structure through a simple mixing procedure. Three nanocomposite materials were considered: carbon nanotubes, graphene oxide, and silica. The evaporation-induced electricity generation was confirmed experimentally under various ambient conditions. Among the nanocomposite materials considered, mesoporous silica (SBA-15) was found to outperform the other two materials in terms of open-circuit voltage, and graphene oxide generated the highest short-circuit current. It was found that the nanocomposite material content in the PVDF film plays an important role: on the one hand, if particles are too few in number, the number of channels will be insufficient to support a strong capillary flow; on the other hand, an excessive number of particles will suppress the flow due to excessive water absorption underneath the surface. We show that the device can be modeled as a simple circuit powered by a current source with excellent agreement between the theoretical predictions and experimental data.

scholarly journals Influence of artificial aging: mechanical and physicochemical properties of dental composites under static and dynamic compression

2021 ◽  
Author(s):  
D. C. Gornig ◽  
R. Maletz ◽  
P. Ottl ◽  
M. Warkentin
Keyword(s):  
Mechanical Properties ◽  
Water Sorption ◽  
Artificial Aging ◽  
Filler Content ◽  
Dynamic Compression ◽  
The Other ◽  
Chemical Degradation ◽  
Dental Composites ◽  
Compression Tests ◽  
Acid Ph

Abstract Objective The aim of the study was to evaluate the influence of filler content, degradation media and time on the mechanical properties of different dental composites after in vitro aging. Materials and Methods Specimens (1 mm3) of three commercially available composites (GrandioSO®, Arabesk Top®, Arabesk Flow®) with respect to their filler content were stored in artificial aging media: artificial saliva, ethanol (60%), lactic acid (pH 5) and citric acid (pH 5). Parameters (Vickers microhardness, compressive strength, elastic modulus, water sorption and solubility) were determined in their initial state (control group, n = 3 for microhardness, n = 5 for the other parameters) and after 14, 30, 90 and 180 days (n = 3 for microhardness, n = 5 for the other parameters for each composite group, time point and media). Specimens were also characterized with dynamic-mechanical-thermal analysis (compression tests, F =  ± 7 N; f = 0.5 Hz, 1 Hz and 3.3 Hz; t = 0–170 °C). Results Incorporation of fillers with more than 80 w% leads to significantly better mechanical properties under static and dynamic compression tests and a better water sorption behavior, even after chemical degradation. The influence of degradation media and time is of subordinate importance for chemical degradation. Conclusion Although the investigated composites have a similar matrix, they showed different degradation behavior. Since dentine and enamel occur only in small layer thickness, a test specimen geometry with very small dimensions is recommended for direct comparison. Moreover, the use of compression tests to determine the mechanical parameters for the development of structure-compatible and functionally adapted composites makes sense as an additional standard. Clinical relevance Preferential use of highly filled composites for occlusal fillings is recommended.

scholarly journals The Effect of Different Annealing Strategies on the Microstructure Development and Mechanical Response of Austempered Steels

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1041
Author(s):  
Eliseo Hernandez-Duran ◽  
Luca Corallo ◽  
Tanya Ros-Yanez ◽  
Felipe Castro-Cerda ◽  
Roumen H. Petrov
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Mechanical Response ◽  
Steel Grade ◽  
The Other ◽  
Microstructure Development ◽  
Microstructural Refinement ◽  
Heterogeneous Distribution ◽  
Parent Austenite ◽  
Conventional Annealing

This study focuses on the effect of non-conventional annealing strategies on the microstructure and related mechanical properties of austempered steels. Multistep thermo-cycling (TC) and ultrafast heating (UFH) annealing were carried out and compared with the outcome obtained from a conventionally annealed (CA) 0.3C-2Mn-1.5Si steel. After the annealing path, steel samples were fast cooled and isothermally treated at 400 °C employing the same parameters. It was found that TC and UFH strategies produce an equivalent level of microstructural refinement. Nevertheless, the obtained microstructure via TC has not led to an improvement in the mechanical properties in comparison with the CA steel. On the other hand, the steel grade produced via a combination of ultrafast heating annealing and austempering exhibits enhanced ductility without decreasing the strength level with respect to TC and CA, giving the best strength–ductility balance among the studied steels. The outstanding mechanical response exhibited by the UFH steel is related to the formation of heterogeneous distribution of ferrite, bainite and retained austenite in proportions 0.09–0.78–0.14. The microstructural formation after UFH is discussed in terms of chemical heterogeneities in the parent austenite.

Ultrapurified Alginate Gel Containing Bone Marrow Aspirate Concentrate Enhances Cartilage and Bone Regeneration on Osteochondral Defects in a Rabbit Model

2021 ◽  
pp. 036354652110141
Author(s):  
Liang Xu ◽  
Atsushi Urita ◽  
Tomohiro Onodera ◽  
Ryosuke Hishimura ◽  
Takayuki Nonoyama ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Bone Marrow ◽  
Cell Transplantation ◽  
Cartilage Repair ◽  
Subchondral Bone ◽  
Bone Repair ◽  
Bone Marrow Aspirate ◽  
Defect Group ◽  
The Other ◽  
Osteochondral Defects

Background: Ultrapurified alginate (UPAL) gel implantation has been demonstrated as effective in cartilage repair for osteochondral defects; however, cell transplantation within UPAL gels would be required to treat larger defects. Hypothesis: The combination of UPAL gel and bone marrow aspirate concentrate (BMAC) would enhance cartilage repair and subchondral bone repair for large osteochondral defects. Study Design: Controlled laboratory study. Methods: A total of 104 osteochondral defects (1 defect per knee) of 52 rabbits were randomly divided into 4 groups (26 defects per group): defects without any treatment (Defect group), defects treated using UPAL gel alone (UPAL group), defects treated using UPAL gel containing allogenic bone marrow mesenchymal stromal cells (UPAL-MSC group), and defects treated using UPAL gel containing BMAC (UPAL-BMAC group). At 4 and 16 weeks postoperatively, macroscopic and histologic evaluations and measurements of repaired subchondral bone volumes of reparative tissues were performed. Collagen orientation and mechanical properties of the reparative tissue were assessed at 16 weeks. Results: The defects in the UPAL-BMAC group were repaired with hyaline-like cartilage with well-organized collagen structures. The histologic scores at 4 weeks were significantly higher in the UPAL-BMAC group (16.9 ± 2.0) than in the Defect group (4.7 ± 1.9; P < .05), the UPAL group (10.0 ± 3.3; P < .05), and the UPAL-MSC group (12.2 ± 2.9; P < .05). At 16 weeks, the score in the UPAL-BMAC group (24.4 ± 1.7) was significantly higher than those in the Defect group (9.0 ± 3.7; P < .05), the UPAL group (14.2 ± 3.9; P < .05), and the UPAL-MSC group (16.3 ± 3.6; P < .05). At 4 and 16 weeks, the macroscopic evaluations were significantly superior in the UPAL-BMAC group compared with the other groups, and the values of repaired subchondral bone volumes in the UPAL-BMAC group were significantly higher than those in the Defect and UPAL groups. The mechanical properties of the reparative tissues were significantly better in the UPAL-BMAC group than in the other groups. Conclusion: The implantation of UPAL gel containing BMAC-enhanced hyaline-like cartilage repair and subchondral bone repair of osteochondral defects in a rabbit knee model. Clinical Relevance: These data support the potential clinical application of 1-step treatment for large osteochondral defects using biomaterial implantation with cell transplantation.

scholarly journals Effects of water absorption on the mechanical properties of hybrid natural fibre/phenol formaldehyde composites

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Sekar Sanjeevi ◽  
Vigneshwaran Shanmugam ◽  
Suresh Kumar ◽  
Velmurugan Ganesan ◽  
Gabriel Sas ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Water Absorption ◽  
Hybrid Composites ◽  
Phenol Formaldehyde ◽  
Natural Fibre ◽  
The Other ◽  
Fibre Reinforcement ◽  
Dry Conditions

AbstractThis investigation is carried out to understand the effects of water absorption on the mechanical properties of hybrid phenol formaldehyde (PF) composite fabricated with Areca Fine Fibres (AFFs) and Calotropis Gigantea Fibre (CGF). Hybrid CGF/AFF/PF composites were manufactured using the hand layup technique at varying weight percentages of fibre reinforcement (25, 35 and 45%). Hybrid composite having 35 wt.% showed better mechanical properties (tensile strength ca. 59 MPa, flexural strength ca. 73 MPa and impact strength 1.43 kJ/m2) under wet and dry conditions as compared to the other hybrid composites. In general, the inclusion of the fibres enhanced the mechanical properties of neat PF. Increase in the fibre content increased the water absorption, however, after 120 h of immersion, all the composites attained an equilibrium state.

Sign in / Sign up

Export Citation Format

Share Document