scholarly journals Magnetoelectric Transducer Designs for Use as Wireless Power Receivers in Wearable and Implantable Applications

Materials ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 512 ◽  
Author(s):  
Tyrel Rupp ◽  
Binh Duc Truong ◽  
Shane Williams ◽  
Shad Roundy
Keyword(s):  
Power Density ◽  
Wearable Devices ◽  
Analytical Models ◽  
Biomedical Implants ◽  
Wireless Power ◽  
Safety Standards ◽  
Inductively Coupled ◽  
Wide Range ◽  
Higher Power ◽  
Magnetoelectric Transducer

As the size of biomedical implants and wearable devices becomes smaller, the need for methods to deliver power at higher power densities is growing. The most common method to wirelessly deliver power, inductively coupled coils, suffers from poor power density for very small-sized receiving coils. An alternative strategy is to transmit power wirelessly to magnetoelectric (ME) or mechano-magnetoelectric (MME) receivers, which can operate efficiently at much smaller sizes for a given frequency. This work studies the effectiveness of ME and MME transducers as wireless power receivers for biomedical implants of very small (<2 mm3) size. The comparative study clearly demonstrates that under existing safety standards, the ME architecture is able to generate a significantly higher power density than the MME architecture. Analytical models for both types of transducers are developed and validated using centimeter scale devices. The Institute of Electrical and Electronics Engineers (IEEE) and the International Commission on Non-Ionizing Radiation Protection (ICNIRP) standards were applied to the lumped elements models which were then used to optimize device dimensions within a 2 mm3 volume. An optimized ME device can produce 21.3 mW/mm3 and 31.3 W/mm3 under the IEEE and ICNIRP standards, respectively, which are extremely attractive for a wide range of biomedical implants and wearable devices.

Preferential Vaporization during Laser Ablation Inductively Coupled Plasma Atomic Emission Spectroscopy

1998 ◽  
Vol 52 (7) ◽  
pp. 913-918 ◽  
Author(s):  
X. L. Mao ◽  
A. C. Ciocan ◽  
R. E. Russo
Keyword(s):  
Laser Ablation ◽  
Power Density ◽  
Nd:Yag Laser ◽  
Inductively Coupled Plasma ◽  
Emission Spectroscopy ◽  
Atomic Emission ◽  
Atomic Emission Spectroscopy ◽  
Plasma Atomic Emission ◽  
Inductively Coupled ◽  
Higher Power

The Zn-to-Cu ratio in brass was measured by laser ablation inductively coupled plasma atomic emission spectroscopy. The influence of laser beam properties (pulse width, wavelength, and power density) on fractional laser ablation was investigated. The behavior of the Zn/Cu ratio vs. laser power density shows that there are different mechanisms influencing ps and ns laser ablation. With the use of a 30 ns pulse duration from an excimer laser, thermal vaporization appears to be the dominant process in the low-power density region. The Zn/Cu ratio approaches stoichiometry at higher power density, but the ablated mass still remains Zn rich. With a 35 ps pulse Nd:YAG laser, a nonthermal mechanism appears to govern the laser ablation process. When a 3 ns Nd:YAG laser is used, both thermal and nonthermal processes exist. For both 3 ns and 30 ps Nd:YAG lasers, stoichiometric ablation can be achieved at higher power densities.

Safety assessment of biological raw materials in the system of medicines quality assurance

2020 ◽  
pp. 63-72
Author(s):  
Yu. Olefir ◽  
E. Sakanyan ◽  
I. Osipova ◽  
V. Dobrynin ◽  
M. Smirnova ◽  
...  
Keyword(s):  
Raw Materials ◽  
State Level ◽  
The State ◽  
Spongiform Encephalopathy ◽  
Safety Standards ◽  
Wide Range ◽  
The Russian Federation ◽  
Key Aspects ◽  
First Time ◽  
Medicines Quality

The entry of a wide range of biotechnological products into the pharmaceutical market calls for rein-forcement of the quality, efficacy and safety standards at the state level. The following general monographs have been elaborated for the first time to be included into the State Pharmacopoeia of the Russian Federation, XIV edition: "Viral safety" and "Reduction of the risk of transmitting animal spongiform encephalopathy via medicinal products". These general monographs were elaborated taking into account the requirements of foreign pharmacopoeias and the WHO recommendations. The present paper summarises the key aspects of the monographs.

Advances in sample digestion using microwave-ultraviolet radiations: phosphorus and sulfur determination in animal feed

2020 ◽  
Vol 16 ◽  
Author(s):  
Diogo L. R. Novo ◽  
Priscila T. Scaglioni ◽  
Rodrigo M. Pereira ◽  
Filipe S. Rondan ◽  
Gilberto S. Coelho Junior ◽  
...  
Keyword(s):  
Inductively Coupled Plasma ◽  
Animal Feed ◽  
Optical Emission ◽  
Emission Spectrometry ◽  
Official Method ◽  
Dissolved Carbon ◽  
Inductively Coupled ◽  
Relative Standard ◽  
Wide Range ◽  
Sulfur Determination

Background: Conventional analytical methods for phosphorus and sulfur determination in several matrices present normally analytical challenges regarding inaccuracy, detectability and waste generation. Objective: The main objective is proposing a green and feasible analytical method for phosphorus and sulfur determination in animal feed. Methods: Synergic effect between microwave and ultraviolet radiations during sample preparation was evaluated for the first time for the animal feed digestion associated with further phosphorus and sulfur determination by ion chromatography with conductivity detection. Dissolved carbon and residual acidity in final digests were used for the proposed method assessment. Phosphorus and sulfur values were compared with those obtained using conventional microwave-assisted wet digestion in closed vessels associated with inductively coupled plasma optical emission spectrometry and with those obtained using Association of Official Analytical Chemists International official method. Recovery tests and certified reference material analysis were performed. Animal feeds were analyzed using the proposed method. Results: Sample masses of 500 mg were efficiently digested using only 2 mol L -1 HNO3. The results obtained by the proposed method was not differing significantly (p > 0.05) from those obtained by the conventional and official methods. Suitable recoveries (from 94 to 99%), agreement with certified values (101 and 104%) and relative standard deviations (< 8%) were achieved. Phosphorus and sulfur content in commercial products varied in a wide range (P: 5,873 to 28,387 mg kg-1 and S: 2,165 to 4,501 mg kg-1 ). Conclusion: The proposed method is a green, safe, accurate, precise and sensitive alternative for animal feed quality control.

scholarly journals Simulation of 2-Coil and 4-Coil Magnetic Resonance Wearable WPT Systems

Proceedings ◽  
2021 ◽  
Vol 68 (1) ◽  
pp. 13
Author(s):  
Yixuan Sun ◽  
Stephen Beeby
Keyword(s):  
Power Efficiency ◽  
Power Transmission ◽  
Rotation Angle ◽  
Wireless Power ◽  
Peak Efficiency ◽  
Frequency Splitting ◽  
At Resonance ◽  
Higher Power ◽  
The Impact ◽  
Proper Frequency

This paper presents the COMSOL simulations of magnetically coupled resonant wireless power transfer (WPT), using simplified coil models for embroidered planar two-coil and four-coil systems. The power transmission of both systems is studied and compared by varying the separation, rotation angle and misalignment distance at resonance (5 MHz). The frequency splitting occurs at short separations from both the two-coil and four-coil systems, resulting in lower power transmission. Therefore, the systems are driven from 4 MHz to 6 MHz to analyze the impact of frequency splitting at close separations. The results show that both systems had a peak efficiency over 90% after tuning to the proper frequency to overcome the frequency splitting phenomenon at close separations below 10 cm. The four-coil design achieved higher power efficiency at separations over 10 cm. The power efficiency of both systems decreased linearly when the axial misalignment was over 4 cm or the misalignment angle between receiver and transmitter was over 45 degrees.

scholarly journals Sidewall Slope Control of InP Via Holes for 3D Integration

Micromachines ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 89
Author(s):  
Jongwon Lee ◽  
Kilsun Roh ◽  
Sung-Kyu Lim ◽  
Youngsu Kim
Keyword(s):  
Inductively Coupled Plasma ◽  
Sio2 Layer ◽  
Etch Depth ◽  
Rf Power ◽  
3D Integration ◽  
Inductively Coupled ◽  
Wide Range ◽  
Via Holes ◽  
Dry Etch ◽  
Icp Etcher

This is the first demonstration of sidewall slope control of InP via holes with an etch depth of more than 10 μm for 3D integration. The process for the InP via holes utilizes a common SiO2 layer as an InP etch mask and conventional inductively coupled plasma (ICP) etcher operated at room temperature and simple gas mixtures of Cl2/Ar for InP dry etch. Sidewall slope of InP via holes is controlled within the range of 80 to 90 degrees by changing the ICP power in the ICP etcher and adopting a dry-etched SiO2 layer with a sidewall slope of 70 degrees. Furthermore, the sidewall slope control of the InP via holes in a wide range of 36 to 69 degrees is possible by changing the RF power in the etcher and introducing a wet-etched SiO2 layer with a small sidewall slope of 2 degrees; this wide slope control is due to the change of InP-to-SiO2 selectivity with RF power.

scholarly journals Microwave Wireless Power Transfer System Based on a Frequency Reconfigurable Microstrip Patch Antenna Array

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 415
Author(s):  
Haiyue Wang ◽  
Lianwen Deng ◽  
Heng Luo ◽  
Junsa Du ◽  
Daohan Zhou ◽  
...  
Keyword(s):  
Resonant Frequency ◽  
Antenna Array ◽  
Patch Antenna ◽  
Wireless Power Transfer ◽  
Microstrip Patch Antenna ◽  
Market Demand ◽  
Power Transfer ◽  
Wireless Power ◽  
Microstrip Patch ◽  
Wide Range

The microwave wireless power transfer (MWPT) technology has found a variety of applications in consumer electronics, medical implants and sensor networks. Here, instead of a magnetic resonant coupling wireless power transfer (MRCWPT) system, a novel MWPT system based on a frequency reconfigurable (covering the S-band and C-band) microstrip patch antenna array is proposed for the first time. By switching the bias voltage-dependent capacitance value of the varactor diode between the larger main microstrip patch and the smaller side microstrip patch, the working frequency band of the MWPT system can be switched between the S-band and the C-band. Specifically, the operated frequencies of the antenna array vary continuously within a wide range from 3.41 to 3.96 GHz and 5.7 to 6.3 GHz. For the adjustable range of frequencies, the return loss of the antenna array is less than −15 dB at the resonant frequency. The gain of the frequency reconfigurable antenna array is above 6 dBi at different working frequencies. Simulation results verified by experimental results have shown that power transfer efficiency (PTE) of the MWPT system stays above 20% at different frequencies. Also, when the antenna array works at the resonant frequency of 3.64 GHz, the PTE of the MWPT system is 25%, 20.5%, and 10.3% at the distances of 20 mm, 40 mm, and 80 mm, respectively. The MWPT system can be used to power the receiver at different frequencies, which has great application prospects and market demand opportunities.

scholarly journals The Survival of Haloferax mediterranei under Stressful Conditions

2021 ◽  
Vol 9 (2) ◽  
pp. 336
Author(s):  
Laura Matarredona ◽  
Mónica Camacho ◽  
Basilio Zafrilla ◽  
Gloria Bravo-Barrales ◽  
Julia Esclapez ◽  
...  
Keyword(s):  
Inductively Coupled Plasma ◽  
Sea Water ◽  
Industrial Applications ◽  
Growth Responses ◽  
Haloferax Mediterranei ◽  
Inductively Coupled ◽  
Icp Ms ◽  
Wide Range ◽  
High Metal ◽  
Plasma Mass Spectrometry

Haloarchaea can survive and thrive under exposure to a wide range of extreme environmental factors, which represents a potential interest to biotechnology. Growth responses to different stressful conditions were examined in the haloarchaeon Haloferax mediterranei R4. It has been demonstrated that this halophilic archaeon is able to grow between 10 and 32.5% (w/v) of sea water, at 32–52 °C, although it is expected to grow in temperatures lower than 32 °C, and between 5.75 and 8.75 of pH. Moreover, it can also grow under high metal concentrations (nickel, lithium, cobalt, arsenic), which are toxic to most living beings, making it a promising candidate for future biotechnological purposes and industrial applications. Inductively Coupled Plasma Mass Spectrometry (ICP-MS) analysis quantified the intracellular ion concentrations of these four metals in Hfx. mediterranei, concluding that this haloarchaeon can accumulate Li+, Co2+, As5+, and Ni2+ within the cell. This paper is the first report on Hfx. mediterranei in which multiple stress conditions have been studied to explore the mechanism of stress resistance. It constitutes the most detailed study in Haloarchaea, and, as a consequence, new biotechnological and industrial applications have emerged.

scholarly journals Recent Advances in Wearable Devices for Non-Invasive Sensing

2021 ◽  
Vol 11 (3) ◽  
pp. 1235
Author(s):  
Su Min Yun ◽  
Moohyun Kim ◽  
Yong Won Kwon ◽  
Hyobeom Kim ◽  
Mi Jung Kim ◽  
...  
Keyword(s):  
Health Monitoring ◽  
Data Transmission ◽  
Wearable Sensors ◽  
Wearable Devices ◽  
Wireless Power ◽  
Non Invasive ◽  
Sensing Systems ◽  
Recent Advances ◽  
Wearable Systems ◽  
Precise Diagnosis

The development of wearable sensors is aimed at enabling continuous real-time health monitoring, which leads to timely and precise diagnosis anytime and anywhere. Unlike conventional wearable sensors that are somewhat bulky, rigid, and planar, research for next-generation wearable sensors has been focused on establishing fully-wearable systems. To attain such excellent wearability while providing accurate and reliable measurements, fabrication strategies should include (1) proper choices of materials and structural designs, (2) constructing efficient wireless power and data transmission systems, and (3) developing highly-integrated sensing systems. Herein, we discuss recent advances in wearable devices for non-invasive sensing, with focuses on materials design, nano/microfabrication, sensors, wireless technologies, and the integration of those.

scholarly journals Universal mobility characteristics of graphene originating from charge scattering by ionised impurities

2021 ◽  
Vol 4 (1) ◽  
Author(s):  
Jonathan H. Gosling ◽  
Oleg Makarovsky ◽  
Feiran Wang ◽  
Nathan D. Cottam ◽  
Mark T. Greenaway ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Carrier Density ◽  
Carrier Mobility ◽  
Carrier Transport ◽  
Analytical Models ◽  
Pristine Graphene ◽  
High Electron ◽  
Boltzmann Transport ◽  
Transport Parameters ◽  
Wide Range

AbstractPristine graphene and graphene-based heterostructures can exhibit exceptionally high electron mobility if their surface contains few electron-scattering impurities. Mobility directly influences electrical conductivity and its dependence on the carrier density. But linking these key transport parameters remains a challenging task for both theorists and experimentalists. Here, we report numerical and analytical models of carrier transport in graphene, which reveal a universal connection between graphene’s carrier mobility and the variation of its electrical conductivity with carrier density. Our model of graphene conductivity is based on a convolution of carrier density and its uncertainty, which is verified by numerical solution of the Boltzmann transport equation including the effects of charged impurity scattering and optical phonons on the carrier mobility. This model reproduces, explains, and unifies experimental mobility and conductivity data from a wide range of samples and provides a way to predict a priori all key transport parameters of graphene devices. Our results open a route for controlling the transport properties of graphene by doping and for engineering the properties of 2D materials and heterostructures.

scholarly journals Jet-gas interactions at crucial jet power for feedback

2014 ◽  
Vol 10 (S313) ◽  
pp. 260-265
Author(s):  
D. M. Worrall ◽  
M. Birkinshaw
Keyword(s):  
Gas Flows ◽  
Rich Cluster ◽  
Power Sources ◽  
X Ray ◽  
Wide Range ◽  
Higher Power ◽  
Radiative Power ◽  
Gas Interactions ◽  
Work Done ◽  
Radio Luminosity Function

AbstractMost X-ray studies of radio-mode feedback have concentrated on locally-abundant low-power radio sources in relatively rich cluster environments. But the scaling found between mechanical and radiative power, when combined with the radio luminosity function, means that half of the heating in the local Universe is expected from higher-power sources, which lie within a factor of about three of the FRI/II transition, and these sources encounter a wide range of atmosphere properties. We summarize what is observed at FRI/II transition powers from a complete sample observed with modest Chandra exposure times. We then discuss two systems with deep Chandra data. In one we find that the work done in driving shocks exceeds that in evacuating cavities. This source also displays a remarkable jet-cloud interaction, and revealing hotspot X-ray emission. In the second we find evidence of radio-emitting plasma running along boundaries between gas of different temperature, apparently lubricating the gas flows and inhibiting heat transfer, and itself being heavily structured by the process.

Sign in / Sign up

Export Citation Format

Share Document