scholarly journals Colloidal Processing of Y0.08Zr0.92O2/La0.80Sr0.20MnO3 Semi-Cells Using a Sr-Doped Lanthanum Manganite Synthesized by a Citrate Route

Materials ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 7831
Author(s):  
Paloma Recio ◽  
Carmen Alcázar ◽  
Rodrigo Moreno
Keyword(s):  
Colloidal Stability ◽  
Tape Casting ◽  
Dip Coating ◽  
Lanthanum Manganite ◽  
X Ray Diffraction ◽  
Full Characterization ◽  
Phase Development ◽  
Different Temperatures ◽  
Excellent Adhesion ◽  
Ysz Electrolyte

In this paper, the interface between yttria stabilized zirconia (Y0.08Zr0.92O2, YSZ) electrolyte and Sr-doped lanthanum manganite (La0.80Sr0.20MnO3, LSM) cathode for solid oxide fuel cells (SOFCs) is studied. For such a purpose, the combination of a suitable synthesis route for obtaining fine powders and simple aqueous colloidal shaping routes is proposed. The synthesis of nanosized particles of La0.80Sr0.20MnO3 by a citrate route and their full characterization, including the colloidal stability and the densification and phase development determined by X-ray diffraction and electron microscopy at different temperatures, is reported. In a second step, YSZ tapes were obtained by aqueous tape casting and used as substrates for the preparation of LSM coatings by dip-coating using aqueous slurries. YSZ tapes were used either in the green state or after a pre-sintering treatment. Co-sintering at 1350 °C led to a sharp interface with excellent adhesion, also achieved when coating pre-sintered tapes. In both cases, the substrates are dense and the coatings are porous, with thicknesses of 85 and 60 μm for green and pre-sintered tapes, respectively. No diffusion of Zr and Y occurs at the LSM layer, but some diffusion of La and Mn towards the YSZ layer takes place.

scholarly journals Effect of Sterilization on the Properties of a Bioactive Hybrid Coating Containing Hydroxyapatite

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
E. K. K. Baldin ◽  
C. F. Malfatti ◽  
V. Rodói ◽  
R. N. Brandalise
Keyword(s):  
Electrochemical Behavior ◽  
Morphological Changes ◽  
Xrd Analysis ◽  
Dip Coating ◽  
Open Circuit ◽  
Hybrid Coating ◽  
Mechanical Resistance ◽  
X Ray Diffraction ◽  
Wear Performance ◽  
Different Temperatures

The objective of this study was to evaluate the influence of sterilization on a hybrid coating obtained from a sol composed of alkoxysilane tetraethoxysilane (TEOS) and organoalkoxysilane methyltriethoxysilane (MTES) containing 10% (mass) of hydroxyapatite particles. The coating was obtained by dip coating, by applying two layers (protective/bioactive), which were cured at different temperatures (450°C and 60°C). The effects of sterilization on the superficial, electrochemical, bioactive, and mechanical properties of the coating were evaluated by performing different sterilization processes, namely, steam autoclave, hydrogen peroxide plasma, and ethylene oxide. Subsequently, the coating was characterized by using scanning electron microscopy (SEM/FEG), and FTIR measurements were performed to characterize the chemical structure. The bioactivity and degradability of the coating were analyzed by mass variation after immersion in SBF and X-ray diffraction (XRD) analysis. The electrochemical behavior was assessed by open circuit potential (OCP) and potentiodynamic polarization curves and the mechanical behavior by wear resistance. Results showed that all sterilization processes caused significant morphological changes in the hybrid coating. The autoclaved sample presented the highest structural chemical changes, and, consequently, the highest degradability, even though it had a superior bioactive behavior in relation to the other samples. In addition, the sterilization processes influenced the electrochemical behavior of the hybrid coating and altered the mechanical resistance to abrasion, thus presenting lower wear performance in relation to the nonsterilized sample.

Annealing effects of high sensitive thin strain gauges consisting of nickel carbon nanocomposites

2018 ◽  
Vol 37 (22) ◽  
pp. 1378-1384 ◽  
Author(s):  
Christos Karapepas ◽  
Daisy Nestler ◽  
Daniel Wett ◽  
Guntram Wagner
Keyword(s):  
Annealing Treatment ◽  
Temperature Stability ◽  
Strain Gauges ◽  
Smart Sensor ◽  
X Ray Diffraction ◽  
X Ray ◽  
Phase Development ◽  
Different Temperatures ◽  
Annealing Effects ◽  
Hybrid Laminates

Hybrid laminates consisting of fiber-reinforced thermoplastic films and metallic thin sheets are successively replacing thermoset-based systems due to their obvious advantages of higher formability and the aptitude for mass production. In order to monitor the material under operating condition, hybrid laminates need to be equipped with smart sensor units. Therefore, the aim of the present work is to evaluate the temperature stability of the Ni-C thin film strain gauge sensors. The analyses of the deposited Ni-C films manufactured by means of a magnetron sputtering process were carried out by means of Raman spectroscopy and X-ray diffraction to investigate the phase development after a heat treatment at different temperatures and holding times. In addition, the four-terminal sensing was utilized to study the change of temperature coefficients of resistance after a single annealing treatment.

scholarly journals A Superhydrophobic, Antibacterial, and Durable Surface of Poplar Wood

Nanomaterials ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1885
Author(s):  
Xinyu Wu ◽  
Feng Yang ◽  
Jian Gan ◽  
Zhangqian Kong ◽  
Yan Wu
Keyword(s):  
Stearic Acid ◽  
Antibacterial Properties ◽  
Alkali Resistance ◽  
Poplar Wood ◽  
X Ray Diffraction ◽  
X Ray ◽  
Different Temperatures ◽  
Acid And Alkali Resistance ◽  
The Stability

The silver particles were grown in situ on the surface of wood by the silver mirror method and modified with stearic acid to acquire a surface with superhydrophobic and antibacterial properties. Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and X-ray energy spectroscopy (XPS) were used to analyze the reaction mechanism of the modification process. Scanning electron microscopy (SEM) and contact angle tests were used to characterize the wettability and surface morphology. A coating with a micro rough structure was successfully constructed by the modification of stearic acid, which imparted superhydrophobicity and antibacterial activity to poplar wood. The stability tests were performed to discuss the stability of its hydrophobic performance. The results showed that it has good mechanical properties, acid and alkali resistance, and UV stability. The durability tests demonstrated that the coating has the function of water resistance and fouling resistance and can maintain the stability of its hydrophobic properties under different temperatures of heat treatment.

scholarly journals Development of Adhesive, Bioactive and Antibacterial Titania Sol-Gel Coating on Titanium Substrate by Dip-Coating Technique

Coatings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 243
Author(s):  
Diana Horkavcová ◽  
Quentin Doubet ◽  
Gisèle Laure Lecomte-Nana ◽  
Eva Jablonská ◽  
Aleš Helebrant
Keyword(s):  
Simulated Body Fluid ◽  
Body Fluid ◽  
Sol Gel ◽  
Titanium Substrate ◽  
Dip Coating ◽  
Coating Technique ◽  
Metal Implants ◽  
Excellent Adhesion ◽  
Titania Sol ◽  
Dip Coating Technique

The sol-gel method provides a wide variety of applications in the medical field. One of these applications is the formation of coatings on the metal implants. The coatings containing specific additive can enhance or improve the existing surface properties of the substrate. In this work, titania sol-gel coatings were doped with two forms of silver (AgNO3, Ag3PO4) and synthetic hydroxyapatite and applied on the titanium samples by dip-coating technique. After drying and slow firing, all coatings were characterized with scanning electron microscopy. Thin coatings were successfully prepared with excellent adhesion to the substrate (measured by ASTM D 3359-2), despite cracks. Coatings containing silver and hydroxyapatite demonstrated a 100% antibacterial effect against Escherichia coli after 24 h. The bioactivity of the coatings containing hydroxyapatite tested in modified simulated body fluid under static-dynamic conditions was confirmed by bone-like hydroxyapatite precipitation. To better understand the interaction of the coatings with simulated body fluid (SBF), changes of Ca2+ and (PO4)3− ions concentrations and pH values were studied.

scholarly journals Hydrothermal Ageing and Its Effect on Fracture Load of Zirconia Dental Implants

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3103
Author(s):  
Laurent Gremillard ◽  
Agnès Mattlet ◽  
Alexandre Mathevon ◽  
Damien Fabrègue ◽  
Bruno Zberg ◽  
...  
Keyword(s):  
Dental Implants ◽  
Fracture Load ◽  
Accelerated Ageing ◽  
Dental Ceramics ◽  
X Ray Diffraction ◽  
X Ray ◽  
Dental Restorations ◽  
Different Temperatures ◽  
Mechanical Performances ◽  
Kinetics Of

Due to growing demand for metal-free dental restorations, dental ceramics, especially dental zirconia, represent an increasing share of the dental implants market. They may offer mechanical performances of the same range as titanium ones. However, their use is still restricted by a lack of confidence in their durability and, in particular, in their ability to resist hydrothermal ageing. In the present study, the ageing kinetics of commercial zirconia dental implants are characterized by X-ray diffraction after accelerated ageing in an autoclave at different temperatures, enabling their extrapolation to body temperature. Measurements of the fracture loads show no effect of hydrothermal ageing even after ageing treatments simulated a 90-year implantation.

scholarly journals A Versatile Approach to Access Trimetallic Complexes Based on Trisphosphinite Ligands

Molecules ◽  
2020 ◽  
Vol 25 (3) ◽  
pp. 593
Author(s):  
Juan Miranda-Pizarro ◽  
Macarena G. Alférez ◽  
M. Dolores Fernández-Martínez ◽  
Eleuterio Álvarez ◽  
Celia Maya ◽  
...  
Keyword(s):  
Coordination Chemistry ◽  
Late Transition Metal ◽  
X Ray Diffraction ◽  
X Ray ◽  
Full Characterization ◽  
Metal Precursors ◽  
Straightforward Method ◽  
One Step ◽  
Late Transition

A straightforward method for the preparation of trisphosphinite ligands in one step, using only commercially available reagents (1,1,1-tris(4-hydroxyphenyl)ethane and chlorophosphines) is described. We have made use of this approach to prepare a small family of four trisphosphinite ligands of formula [CH3C{(C6H4OR2)3], where R stands for Ph (1a), Xyl (1b, Xyl = 2,6-Me2-C6H3), iPr (1c), and Cy (1d). These polyfunctional phosphinites allowed us to investigate their coordination chemistry towards a range of late transition metal precursors. As such, we report here the isolation and full characterization of a number of Au(I), Ag(I), Cu(I), Ir(III), Rh(III) and Ru(II) homotrimetallic complexes, including the structural characterization by X-ray diffraction studies of six of these compounds. We have observed that the flexibility of these trisphosphinites enables a variety of conformations for the different trimetallic species.

scholarly journals Modeling of magneto-conductivity of bismuth selenide: a topological insulator

2021 ◽  
Vol 3 (4) ◽  
Author(s):  
Yogesh Kumar ◽  
Rabia Sultana ◽  
Prince Sharma ◽  
V. P. S. Awana
Keyword(s):  
Magnetic Field ◽  
Magnetic Fields ◽  
Single Crystal ◽  
Single Crystals ◽  
X Ray Diffraction ◽  
Field Range ◽  
X Ray ◽  
Bulk Carriers ◽  
Different Temperatures

AbstractWe report the magneto-conductivity analysis of Bi2Se3 single crystal at different temperatures in a magnetic field range of ± 14 T. The single crystals are grown by the self-flux method and characterized through X-ray diffraction, Scanning Electron Microscopy, and Raman Spectroscopy. The single crystals show magnetoresistance (MR%) of around 380% at a magnetic field of 14 T and a temperature of 5 K. The Hikami–Larkin–Nagaoka (HLN) equation has been used to fit the magneto-conductivity (MC) data. However, the HLN fitted curve deviates at higher magnetic fields above 1 T, suggesting that the role of surface-driven conductivity suppresses with an increasing magnetic field. This article proposes a speculative model comprising of surface-driven HLN and added quantum diffusive and bulk carriers-driven classical terms. The model successfully explains the MC of the Bi2Se3 single crystal at various temperatures (5–200 K) and applied magnetic fields (up to 14 T).

Growth study of epitaxial FexZn1−xF2 thin films

2001 ◽  
Vol 16 (6) ◽  
pp. 1769-1775 ◽  
Author(s):  
J. McChesney ◽  
M. Hetzer ◽  
H. Shi ◽  
T. Charlton ◽  
D. Lederman
Keyword(s):  
Thin Films ◽  
Film Growth ◽  
Magnetic Phase Diagram ◽  
Epitaxial Thin Films ◽  
X Ray Diffraction ◽  
Growth Study ◽  
Lattice Match ◽  
Different Temperatures ◽  
Bulk Single Crystals ◽  
The Ideal

The FexZn1−xF2 alloy has been shown to be a model system for studying the magnetic phase diagram of dilute magnets. Whereas the growth of bulk single crystals with fixed Zn concentrations is difficult, the thin film growth is comparatively simpler and more flexible. To gain an understanding of the growth of FexZn1−xF2 films, a method was developed to grow smooth films at fixed concentrations. This was done by depositing a MgF2 buffer layer on MgF2(001) substrates and then depositing FeF2 and ZnF2 [001]-orientated epitaxial thin films at different temperatures. Surprisingly, the lattice spacing depends strongly on the growth temperature, for 44-nm-thick FeF2 films and 77-nm-thick ZnF2 films. This indicates a significant amount of stress, despite the close lattice match between the films and the MgF2 substrate. Thick alloy samples (approximately 500 nm thick) were grown by co-evaporation from the FeF2 and ZnF2 sources at the ideal temperature determined from the growth study, and their concentration was accurately determined using x-ray diffraction.

Effect of Reinforcement and Tribological Behaviour of AA 7068 Hybrid Composites Manufactured through Powder Metallurgy Techniques

2017 ◽  
Vol 867 ◽  
pp. 19-28 ◽  
Author(s):  
J. Lakshmipathy ◽  
Subburaj Rajesh Kannan ◽  
K. Manisekar ◽  
S. Vinoth Kumar
Keyword(s):  
Sintering Temperature ◽  
Hybrid Composites ◽  
High Strength ◽  
Phase Changes ◽  
Wear Loss ◽  
X Ray Diffraction ◽  
Tribological Behaviour ◽  
Different Temperatures ◽  
Pin On Disc ◽  
Sliding Distance

In this article, an attempt was made to study the mechanical behaviour of AA7068 - 6 vol. % of MoS2 - X vol. % of WC (X = 0, 5, 10 and 15) hybrid aluminium composites produced by blend–press–sinter methodology. Compacted Powders (700MPa) were sintered at different temperatures (450 0c, 500 0c and 550 0c ) in order to find the influence of sintering temperature on mechanical properties and tribological behavior of AA7068 hybrid composites.The sintered samples have been characterized by x-ray diffraction (XRD) method for identification of phases and also to investigate the phase changes. The change in density, hardness and porosity values of composites were reported. The composite with 15 vol. % of tungsten carbide and 6 vol. % of MoS2 showed the highest hardness and density at the sintering temperature range of 550 0c. Pin-on-disc type apparatus was used for determining the wear loss occurring at different conditions. The hybridization of the two reinforcements enhanced the wear resistance of the composites, especially under high applied load, sliding distance and sliding speeds. Due to this, the hybrid aluminium composites can be considered as an outstanding material where high strength and wear-resistant components are of major importance, predominantly in the aerospace and automotive engineering sectors. The morphology of the wear debris and the worn out surfaces were analyzed to understand the wear mechanisms.

CHARACTERIZATION OF HYDROXYAPATITE/TI6AL4V COMPOSITE POWDER UNDER VARIOUS SINTERING TEMPERATURE

2015 ◽  
Vol 75 (7) ◽  
Author(s):  
Amir Arifin ◽  
Abu Bakar Sulong ◽  
Norhamidi Muhamad ◽  
Junaidi Syarif
Keyword(s):  
Mechanical Properties ◽  
Composite Powder ◽  
Sintering Temperature ◽  
Physical And Mechanical Properties ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Different Temperatures ◽  
Two Phases ◽  
Work Interaction

Hydroxyapatite (HA) has been widely used in biomedical applications due to its excellent biocompatibility. However, Hydroxyapatite possesses poor mechanical properties and only tolerate limited loads for implants. Titanium is well-known materials applied in implant that has advantage in mechanical properties but poor in biocompatibility. The combination of the Titanium alloy and HA is expected to produce bio-implants with good in term of mechanical properties and biocompatabilty. In this work, interaction and mechanical properties of HA/Ti6Al4V was analyzed. The physical and mechanical properties of HA/Ti6Al4V composite powder obtained from compaction (powder metallurgy) of 60 wt.% Ti6Al4V and 40 wt.% HA and sintering at different temperatures in air were investigated in this study. Interactions of the mixed powders were investigated using X-ray diffraction. The hardness and density of the HA/Ti6Al4V composites were also measured. Based on the results of XRD analysis, the oxidation of Ti began at 700 °C. At 1000 °C, two phases were formed (i.e., TiO2 and CaTiO3). The results showed that the hardness HA/Ti6Al4V composites increased by 221.6% with increasing sintering temperature from 700oC to 1000oC. In contrast, the density of the composites decreased by 1.9% with increasing sintering temperature. 

Sign in / Sign up

Export Citation Format

Share Document