scholarly journals Self-Healing and Mechanical Properties of Thermoplastic Polyurethane/Eugenol-Based Phenoxy Resin Blends via Exchange Reactions

Polymers ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 1011 ◽  
Author(s):  
Jing-Yu Liang ◽  
Se-Ra Shin ◽  
Soo-Hyoung Lee ◽  
Dai-Soo Lee
Keyword(s):  
Mechanical Properties ◽  
Exchange Reaction ◽  
Thermoplastic Polyurethane ◽  
Mechanical Analysis ◽  
Resin Content ◽  
Self Healing ◽  
Exchange Reactions ◽  
Scanning Calorimetry ◽  
Healing Efficiency ◽  
Different Types

The possibility of exchange reactions and thermal self-healing in blends of thermoplastic polyurethane (TPU) and phenoxy resin was investigated herein. The analyses were based on characterization obtained via differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), dynamic mechanical analysis (DMA), and tensile test. A new phenoxy resin was synthesized from eugenol, and blends with different types of TPU were prepared to investigate the exchange reaction, thermal self-healing, and mechanical properties. The influence of phenoxy resin content on the mechanical behavior and healing efficiency was studied. Improvement of storage modulus owing to the increase of phenoxy resin content was observed. Results suggest that the exchange reaction between phenoxy- and ester-type TPU occurred during thermal treatment. However, little exchange occurred between phenoxy resin and ether-type TPU. Specifically, only ester-type TPU exhibited a significant exchange reaction in the phenoxy resin blend. Furthermore, in the presence of a catalyst (e.g., zinc acetate), the exchange reaction readily occurred, and the healing efficiency improved by the addition of the catalyst and increase in the phenoxy content.

scholarly journals Biodegradable and Toughened Composite of Poly(Propylene Carbonate)/Thermoplastic Polyurethane (PPC/TPU): Effect of Hydrogen Bonding

2018 ◽  
Vol 19 (7) ◽  
pp. 2032 ◽  
Author(s):  
Dongmei Han ◽  
Guiji Chen ◽  
Min Xiao ◽  
Shuanjin Wang ◽  
Shou Chen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Propylene Carbonate ◽  
Thermoplastic Polyurethane ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Scanning Calorimetry ◽  
Thermal Stabilities ◽  
Dynamic Mechanical ◽  
Brittle Ductile Transition ◽  
Poly Propylene

The blends of Poly(propylene carbonate) (PPC) and polyester-based thermoplastic polyurethane (TPU) were melt compounded in an internal mixer. The compatibility, thermal behaviors, mechanical properties and toughening mechanism of the blends were investigated using Fourier transform infrared spectra (FTIR), tensile tests, impact tests, differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and dynamic mechanical analysis technologies. FTIR and SEM examination reveal strong interfacial adhesion between PPC matrix and suspended TPU particles. Dynamic mechanical analyzer (DMA) characterize the glass transition temperature, secondary motion and low temperature properties. By the incorporation of TPU, the thermal stabilities are greatly enhanced and the mechanical properties are obviously improved for the PPC/TPU blends. Moreover, PPC/TPU blends exhibit a brittle-ductile transition with the addition of 20 wt % TPU. It is considered that the enhanced toughness results in the shear yielding occurred in both PPC matrix and TPU particles of the blends.

scholarly journals Relationship between the Stereocomplex Crystallization Behavior and Mechanical Properties of PLLA/PDLA Blends

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1851
Author(s):  
Hye-Seon Park ◽  
Chang-Kook Hong
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Crystallization Behavior ◽  
Mechanical Analysis ◽  
X Ray Diffraction ◽  
Nucleation Agent ◽  
Scanning Calorimetry ◽  
Nucleation Sites ◽  
Wide Range ◽  
Degree Of Crystallization

Poly (l-lactic acid) (PLLA) is a promising biomedical polymer material with a wide range of applications. The diverse enantiomeric forms of PLLA provide great opportunities for thermal and mechanical enhancement through stereocomplex formation. The addition of poly (d-lactic acid) (PDLA) as a nucleation agent and the formation of stereocomplex crystallization (SC) have been proven to be an effective method to improve the crystallization and mechanical properties of the PLLA. In this study, PLLA was blended with different amounts of PDLA through a melt blending process and their properties were calculated. The effect of the PDLA on the crystallization behavior, thermal, and mechanical properties of PLLA were investigated systematically by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X-ray diffraction (XRD), polarized optical microscopy (POM), dynamic mechanical analysis (DMA), and tensile test. Based on our findings, SC formed easily when PDLA content was increased, and acts as nucleation sites. Both SC and homo crystals (HC) were observed in the PLLA/PDLA blends. As the content of PDLA increased, the degree of crystallization increased, and the mechanical strength also increased.

scholarly journals Mechanical, Thermal and Rheological Properties of Polyethylene-Based Composites Filled with Micrometric Aluminum Powder

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1242
Author(s):  
Olga Mysiukiewicz ◽  
Paulina Kosmela ◽  
Mateusz Barczewski ◽  
Aleksander Hejna
Keyword(s):  
Mechanical Properties ◽  
Melt Flow Index ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Flow Index ◽  
Scanning Calorimetry ◽  
Metal Composites ◽  
Pre Treatment ◽  
The Impact ◽  
Properties Of Composites

Investigations related to polymer/metal composites are often limited to the analysis of the electrical and thermal conductivity of the materials. The presented study aims to analyze the impact of aluminum (Al) filler content (from 1 to 20 wt%) on the rarely investigated properties of composites based on the high-density polyethylene (HDPE) matrix. The crystalline structure, rheological (melt flow index and oscillatory rheometry), thermal (differential scanning calorimetry), as well as static (tensile tests, hardness, rebound resilience) and dynamic (dynamical mechanical analysis) mechanical properties of composites were investigated. The incorporation of 1 and 2 wt% of aluminum filler resulted in small enhancements of mechanical properties, while loadings of 5 and 10 wt% provided materials with a similar performance to neat HDPE. Such results were supported by the lack of disturbances in the rheological behavior of composites. The presented results indicate that a significant content of aluminum filler may be introduced into the HDPE matrix without additional pre-treatment and does not cause the deterioration of composites’ performance, which should be considered beneficial when engineering PE/metal composites.

scholarly journals Recyclable Self-Healing Polyurethane Cross-Linked by Alkyl Diselenide with Enhanced Mechanical Properties

Polymers ◽  
2019 ◽  
Vol 11 (5) ◽  
pp. 773 ◽  
Author(s):  
Yuqing Qian ◽  
Xiaowei An ◽  
Xiaofei Huang ◽  
Xiangqiang Pan ◽  
Jian Zhu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Room Temperature ◽  
Amide Bond ◽  
Self Healing ◽  
Healing Efficiency ◽  
Polyurethane Networks ◽  
Combined Action ◽  
Cross Linker ◽  
Dynamic Structures ◽  
External Interventions

Dynamic structures containing polymers can behave as thermosets at room temperature while maintaining good mechanical properties, showing good reprocessability, repairability, and recyclability. In this work, alkyl diselenide is effectively used as a dynamic cross-linker for the design of self-healing poly(urea–urethane) elastomers, which show quantitative healing efficiency at room temperature, without the need for any catalysts or external interventions. Due to the combined action of the urea bond and amide bond, the material has better mechanical properties. We also compared the self-healing effect of alkyl diselenide-based polyurethanes and alkyl disulfide-based polyurethanes. The alkyl diselenide has been incorporated into polyurethane networks using a para-substituted amine diphenyl alkyl diselenide. The resulting materials not only exhibit faster self-healing properties than the corresponding disulfide-based materials, but also show the ability to be processed at temperatures as low as 60 °C.

scholarly journals Preparation and Characterization of Talc Filled Thermoplastic Polyurethane/Polypropylene Blends

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Emi Govorčin Bajsić ◽  
Vesna Rek ◽  
Ivana Ćosić
Keyword(s):  
Thermal Properties ◽  
Thermoplastic Polyurethane ◽  
Mechanical Analysis ◽  
Degree Of Crystallinity ◽  
Scanning Calorimetry ◽  
Polypropylene Blends ◽  
Pp Blends ◽  
The Degree Of Crystallinity ◽  
Better Than

The effect of the addition of talc on the morphology and thermal properties of blends of thermoplastic polyurethane (TPU) and polypropylene (PP) was investigated. The blends of TPU and PP are incompatible because of large differences in polarities between the nonpolar crystalline PP and polar TPU and high interfacial tensions. The interaction between TPU and PP can be improved by using talc as reinforcing filler. The morphology was observed by means of scanning electron microscopy (SEM). The thermal properties of the neat polymers and unfilled and talc filled TPU/PP blends were studied by using dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The addition of talc in TPU/PP blends improved miscibility in all investigated TPU/T/PP blends. The DSC results for talc filled TPU/PP blends show that the degree of crystallinity increased, which is due to the nucleating effect induced by talc particles. The reason for the increased storage modulus of blends with the incorporation of talc is due to the improved interface between polymers and filler. According to TGA results, the addition of talc enhanced thermal stability. The homogeneity of the talc filled TPU/PP blends is better than unfilled TPU/PP blends.

scholarly journals Numerical Studies of the Effects of Water Capsules on Self-Healing Efficiency and Mechanical Properties in Cementitious Materials

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Haoliang Huang ◽  
Guang Ye
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Cementitious Materials ◽  
Self Healing ◽  
Negative Effects ◽  
Numerical Studies ◽  
Healing Efficiency ◽  
The Impact ◽  
Positive Effect

In this research, self-healing due to further hydration of unhydrated cement particles is taken as an example for investigating the effects of capsules on the self-healing efficiency and mechanical properties of cementitious materials. The efficiency of supply of water by using capsules as a function of capsule dosages and sizes was determined numerically. By knowing the amount of water supplied via capsules, the efficiency of self-healing due to further hydration of unhydrated cement was quantified. In addition, the impact of capsules on mechanical properties was investigated numerically. The amount of released water increases with the dosage of capsules at different slops as the size of capsules varies. Concerning the best efficiency of self-healing, the optimizing size of capsules is 6.5 mm for capsule dosages of 3%, 5%, and 7%, respectively. Both elastic modulus and tensile strength of cementitious materials decrease with the increase of capsule. The decreasing tendency of tensile strength is larger than that of elastic modulus. However, it was found that the increase of positive effect (the capacity of inducing self-healing) of capsules is larger than that of negative effects (decreasing mechanical properties) when the dosage of capsules increases.

Enhancing the Thermal and Mechanical Characteristics of Polyvinyl Alcohol (PVA)-Hemp Protein Particles (HPP) Composites

2021 ◽  
Vol 36 (2) ◽  
pp. 137-143
Author(s):  
S. A. Awad
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperatures ◽  
Composite Films ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Decomposition Temperature ◽  
Scanning Calorimetry ◽  
Solution Casting Method ◽  
Protein Particles

Abstract This paper aims to describe the thermal, mechanical, and surface properties of a PVA/HPP blend whereby the film was prepared using a solution casting method. The improvements in thermal and mechanical properties of HPP-based PVA composites were investigated. The characterization of pure PVA and PVA composite films included tensile tests, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The results of TGA and DSC indicated that the addition of HPP increased the thermal decomposition temperature of the composites. Mechanical properties are significantly improved in PVA/HPP composites. The thermal stability of the PVA composite increased with the increase of HPP filler content. The tensile strength increased from 15.74 ± 0.72 MPa to 27.54 ± 0.45 MPa and the Young’s modulus increased from 282.51 ± 20.56 MPa to 988.69 ± 42.64 MPa for the 12 wt% HPP doped sample. Dynamic mechanical analysis (DMA) revealed that at elevated temperatures, enhanced mechanical properties because of the presence of HPP was even more noticeable. Morphological observations displayed no signs of agglomeration of HPP fillers even in composites with high HPP loading.

Physico Chemical Characterization of Nanofibrous Poly(Ε-Caprolactone) Electrospun Templates for Cell Adhesion

MRS Advances ◽  
2017 ◽  
Vol 2 (49) ◽  
pp. 2689-2694
Author(s):  
Karla A. Gaspar-Ovalle ◽  
Juan V. Cauich-Rodriguez ◽  
Armando Encinas
Keyword(s):  
Mechanical Properties ◽  
Differential Scanning Calorimetry ◽  
Cell Adhesion ◽  
Tensile Modulus ◽  
Chemical Characterization ◽  
Mechanical Analysis ◽  
Scanning Calorimetry ◽  
Water Contact ◽  
Physico Chemical ◽  
Static Water

ABSTRACTNanofibrous mats of poly ε-caprolactone (PCL) were fabricated by electrospinning. The nanofiber structures were investigated and characterized by scanning electron microscope, differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical analysis, static water-contact-angle analysis and mechanical properties. The results showed that the nanofibrous PCL is an ideal biopolymer for cell adhesion, owing to its biocompatibility, biodegradability, structural stability and mechanical properties. Differential scanning calorimetry results showed that the fibrous structure of PCL does not alter its crystallinity. Studies of the mechanical properties, wettability and degradability showed that the structure of the electrospun PCL improved the tensile modulus, tensile strength, wettability and biodegradability of the nanotemplates. To evaluate the nanofibrous structure of PCL on cell adhesion, osteoblasts cells were seeded on these templates. The results showed that both adhesion and proliferation of the cells is viable on these electrospun PCL membranes. Thus electrospinning is a relatively inexpensive and scalable manufacturing technique for submicron to nanometer diameter fibers, which can be of interest in the commodity industry.

Preparation of vinyl polymer/polyurethane hybrid latex particles and their application in nano-sized vinyl polymer particle/thermoplastic polyurethane blends

e-Polymers ◽  
2010 ◽  
Vol 10 (1) ◽  
Author(s):  
Yanyan Wei ◽  
Chengzhong Zong ◽  
Fufang Wang
Keyword(s):  
Mechanical Properties ◽  
Thermoplastic Polyurethane ◽  
Polymer Particle ◽  
Gravimetric Analysis ◽  
Hybrid Particles ◽  
Scanning Calorimetry ◽  
Latex Particles ◽  
Vinyl Polymer ◽  
Hybrid Latex ◽  
Polyurethane Matrix

AbstractVinyl polymer/polyurethane hybrid latex particles with various compositions were successfully prepared via emulsion polymerization of vinyl monomer in the presence of self-emulsified polyurethane dispersion without using any surfactant. Studies were carried out on polymerization kinetics, characterization of the hybrid particles and the physical properties of nano-sized vinyl polymer particle/thermoplastic polyurethane blends. It was found that the maximum content of vinyl polymer in polyurethane hybrid particles was up to 80 percent and all of the vinyl polymer/polyurethane hybrid particles were less than 120 nm. Infrared spectroscopy, thermal gravimetric analysis and differential scanning calorimetry analysis indicated the influence of vinyl polymer on the polyurethane hybrid particles. With the polyurethane shells outside and, therefore, good compatibility with polyurethane matrix, the hybrid particles can be easily blended into polyurethane matrix. Some unusual changes of dynamic mechanical properties in the low temperature region were found in the blends of hybrid particles and thermoplastic polyurethane. With the addition of only 3%, the mechanical properties of these blends did not show a significant change. This study provided a new method to prepare hybrid particles in the absence of surfactant and made an attempt on application of vinyl polymer/polyurethane hybrid particles in the blending modification

The Structure and Mechanical Properties of Plastically Consolidated Al-Ni Alloy

2016 ◽  
Vol 682 ◽  
pp. 245-251 ◽  
Author(s):  
Grzegorz Włoch ◽  
Tomasz Skrzekut ◽  
Jakub Sobota ◽  
Antoni Woźnicki ◽  
Justyna Cisoń
Keyword(s):  
Mechanical Properties ◽  
Vickers Hardness ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Intermetallic Phases ◽  
Scanning Calorimetry ◽  
Porosity Formation ◽  
X Ray ◽  
Ni Alloy ◽  
Thermal Stability Of

Mixed and preliminarily consolidated powders of aluminium and nickel (90 mass % Al and 10 mass % Ni) were hot extruded. As results the rod, 8 mm in diameter, was obtained. As-extruded material was subjected to the microstructural investigations using scanning electron microscopy (SEM/EDS) and X-ray analysis (XRD). The differential scanning calorimetry (DSC) and thermo-mechanical analysis (TMA) were also performed. The mechanical properties of as extruded material were determined by the tensile test and Vickers hardness measurements. In order to evaluate the thermal stability of PM alloy, samples were annealed at the temperature of 475 and 550 °C. After annealing Vickers hardness measurements and tensile tests were carried out. The plastic consolidation of powders during extrusion was found to be very effective, because no pores or voids were observed in the examined material. The detailed microstructural investigations and XRD analyses did not reveal the presence of the intermetallic phases in the as-extruded material. During annealing, the Al3Ni intermetallic compound was formed as the result of chemical reaction between the alloy components. The hardness of the alloy after annealing at the temperature of 475°C was found to be comparable to the hardness in as-extruded state. Annealing of the material at the temperature of 550°C results in hardness decreasing by about 50%, as the consequence of porosity formation and Al3Ni cracking.

Sign in / Sign up

Export Citation Format

Share Document