Indentation Behavior of a Closed-Cell Aluminum Foam at Elevated Temperatures

2013 ◽  
Vol 535-536 ◽  
pp. 219-222 ◽  
Author(s):  
Zhi Bin Li ◽  
Zhi Jun Zheng ◽  
Ji Lin Yu
Keyword(s):  
Elevated Temperatures ◽  
Lateral Spread ◽  
Compression Tests ◽  
Aluminum Foams ◽  
Temperature Dependent ◽  
Cross Sectional ◽  
Collapse Strength ◽  
Closed Cell ◽  
Indentation Tests ◽  
Deep Indentation

A series of deep indentation and uniaxial compression tests of closed-cell aluminum foams at room temperature as well as elevated temperatures were conducted. A flat-ended punch (FEP) was used in the indentation tests. Cross-sectional views of the specimens after tests show that the deformation is roughly confined to the material directly underneath the indenter with slightly lateral spread. It is found that plastic collapse strength and energy absorption of the specimens are temperature dependent in both loading conditions. Tear energy of the foam in FEP indentation depends on the indentation depth and temperature.

Resistance of Thin Al Foam Panels to Deep Indentation

2007 ◽  
Vol 561-565 ◽  
pp. 357-360 ◽  
Author(s):  
Maizlinda I. Idris ◽  
Tania Vodenitcharova ◽  
Mark Hoffman
Keyword(s):  
Uniaxial Compression ◽  
Bulk Material ◽  
Deformation Behaviour ◽  
Metallic Foams ◽  
Closed Cell ◽  
Crushing Force ◽  
Indentation Tests ◽  
Al Foam ◽  
Deep Indentation ◽  
Combined Action

In recent years there has been a considerable amount of research into the deformation behaviour of metallic foams. The majority of this research has only addressed size-independent bulk material properties, obtained through uniaxial compression and indentation tests of thick blocks. There is little information in the literature on the indentation response of thin panels, which has motivated the current study. Thin panels of ALPORAS closed-cell foam of ~ 0.25 g/cm3 density were tested in uniaxial compression, and were indented with long flat-plate punches and long cylindrical punches. Cross-sectioning of the samples following interrupted testing revealed the plastic strain evolution process. The deformation was attributed to the progressive crushing of the cell bands, and the combined action of shearing and tearing resistance. Based on energy formalism, a model was developed to estimate the crushing force. By fitting the experimental loaddisplacement curves, the foam ligament tearing energy was deduced for all types of indentation. The absorbed energy was also calculated for the uniaxial compression and indentation experiments.

Interface structure and formation between gold and trimethylcyclohexane polycarbonate

1999 ◽  
Vol 14 (9) ◽  
pp. 3538-3543 ◽  
Author(s):  
C. v. Bechtolsheim ◽  
V. Zaporojtchenko ◽  
F. Faupel
Keyword(s):  
Photoelectron Spectroscopy ◽  
Elevated Temperatures ◽  
Cluster Formation ◽  
Systematic Investigation ◽  
Temperature Dependent ◽  
Cross Sectional ◽  
Force Microscopy ◽  
Metal Diffusion ◽  
Atomic Force ◽  
Transmission Electron

This paper presents the results of a systematic investigation of structure and formation of the interface between gold and trimethylcyclohexane polycarbonate, particularly concerning interface evolvement during gold evaporation and the influence of evaporation rate, substrate temperature, and subsequent annealing. The means of investigation were cross-sectional transmission electron microscopy, atomic force microscopy, and x-ray photoelectron spectroscopy. Extensive metal diffusion into the polymer and cluster formation near the interface were observed at deposition rates of the order of one monolayer per minute and below. The penetration depth is strongly temperature dependent. At high evaporation rates metal aggregation at the surface prevents cluster formation inside the polymer. No diffusion into the polymer was observed from metal films deposited at room temperature after extensive annealing at elevated temperatures.

High-Temperature Instability of A Cr2Nb-Nb(Cr) Microlaminate Composite

1996 ◽  
Vol 54 ◽  
pp. 374-375
Author(s):  
M. Larsen ◽  
R.G. Rowe ◽  
D.W. Skelly
Keyword(s):  
Heat Treatment ◽  
Solid Solution ◽  
High Temperature ◽  
Elevated Temperatures ◽  
Aircraft Engine ◽  
Lattice Parameter ◽  
Microstructural Stability ◽  
Elevated Temperature Strength ◽  
Cross Sectional ◽  
Bcc Structure

Microlaminate composites consisting of alternating layers of a high temperature intermetallic compound for elevated temperature strength and a ductile refractory metal for toughening may have uses in aircraft engine turbines. Microstructural stability at elevated temperatures is a crucial requirement for these composites. A microlaminate composite consisting of alternating layers of Cr2Nb and Nb(Cr) was produced by vapor phase deposition. The stability of the layers at elevated temperatures was investigated by cross-sectional TEM.The as-deposited composite consists of layers of a Nb(Cr) solid solution with a composition in atomic percent of 91% Nb and 9% Cr. It has a bcc structure with highly elongated grains. Alternating with this Nb(Cr) layer is the Cr2Nb layer. However, this layer has deposited as a fine grain Cr(Nb) solid solution with a metastable bcc structure and a lattice parameter about half way between that of pure Nb and pure Cr. The atomic composition of this layer is 60% Cr and 40% Nb. The interface between the layers in the as-deposited condition appears very flat (figure 1). After a two hour, 1200 °C heat treatment, the metastable Cr(Nb) layer transforms to the Cr2Nb phase with the C15 cubic structure. Grain coarsening occurs in the Nb(Cr) layer and the interface between the layers roughen. The roughening of the interface is a prelude to an instability of the interface at higher heat treatment temperatures with perturbations of the Cr2Nb grains penetrating into the Nb(Cr) layer.

Phase transformation and layer evolution in molybdenum disilicide-silicon carbide nanolayered coatings

1994 ◽  
Vol 52 ◽  
pp. 538-539
Author(s):  
H. Kung ◽  
T. R. Jervis ◽  
J.-P. Hirvonen ◽  
M. Nastasi ◽  
T. E. Mitchell ◽  
...  
Keyword(s):  
Phase Transformation ◽  
High Temperature ◽  
Oxidation Resistance ◽  
Elevated Temperatures ◽  
Matrix Material ◽  
Molybdenum Disilicide ◽  
High Temperature Strength ◽  
Cross Sectional ◽  
Good Oxidation Resistance ◽  
Structural Applications

MoSi2 is a potential matrix material for high temperature structural composites due to its high melting temperature and good oxidation resistance at elevated temperatures. The two major drawbacksfor structural applications are inadequate high temperature strength and poor low temperature ductility. The search for appropriate composite additions has been the focus of extensive investigations in recent years. The addition of SiC in a nanolayered configuration was shown to exhibit superior oxidation resistance and significant hardness increase through annealing at 500°C. One potential application of MoSi2- SiC multilayers is for high temperature coatings, where structural stability ofthe layering is of major concern. In this study, we have systematically investigated both the evolution of phases and the stability of layers by varying the heat treating conditions.Alternating layers of MoSi2 and SiC were synthesized by DC-magnetron and rf-diode sputtering respectively. Cross-sectional transmission electron microscopy (XTEM) was used to examine three distinct reactions in the specimens when exposed to different annealing conditions: crystallization and phase transformation of MoSi2, crystallization of SiC, and spheroidization of the layer structures.

Effect Of Elevated Temperatures On Complete Concrete Deformation Diagrams

2019 ◽  
pp. 9-14
Keyword(s):  
Experimental Data ◽  
Elastic Modulus ◽  
Elevated Temperatures ◽  
Peak Load ◽  
Relative Deformation ◽  
Deformation Characteristics ◽  
Compression Tests ◽  
Strain Behavior ◽  
Different Temperatures ◽  
Deformation Diagrams

The analysis of the previous results of the study on concrete stress-strain behavior at elevated temperatures has been carried out. Based on the analysis, the main reasons for strength retrogression and elastic modulus reduction of concrete have been identified. Despite a significant amount of research in this area, there is a large spread in experimental data received, both as a result of compression and tension. In addition, the deformation characteristics of concrete are insufficiently studied: the coefficient of transverse deformation, the limiting relative compression deformation corresponding to the peak load and the almost complete absence of studies of complete deformation diagrams at elevated temperatures. The two testing chambers provided creating the necessary temperature conditions for conducting studies under bending compression and tension have been developed. On the basis of the obtained experimental data of physical and mechanical characteristics of concrete at different temperatures under conditions of axial compression and tensile bending, conclusions about the nature of changes in strength and deformation characteristics have been drawn. Compression tests conducted following the method of concrete deformation complete curves provided obtaining diagrams not only at normal temperature, but also at elevated temperature. Based on the experimental results, dependences of changes in prism strength and elastic modulus as well as an equation for determining the relative deformation and stresses at elevated temperatures at all stages of concrete deterioration have been suggested.

On multiaxial failure behavior of closed-cell aluminum foams under medium strain rates

2021 ◽  
Vol 160 ◽  
pp. 107278
Author(s):  
Erdong Wang ◽  
Guangyong Sun ◽  
Gang Zheng ◽  
Qing Li
Keyword(s):  
Failure Behavior ◽  
Strain Rates ◽  
Aluminum Foams ◽  
Closed Cell

scholarly journals Thermal stability and diffusion characteristics of ultrathin amorphous carbon films grown on crystalline and nitrogenated silicon substrates by filtered cathodic vacuum arc deposition

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Shengxi Wang ◽  
Anurag Roy ◽  
Kyriakos Komvopoulos
Keyword(s):  
Thermal Stability ◽  
Amorphous Carbon ◽  
Silicon Substrate ◽  
Elevated Temperatures ◽  
Carbon Films ◽  
Vacuum Arc ◽  
Cross Sectional ◽  
Prolonged Heating ◽  
Filtered Cathodic Vacuum Arc ◽  
Thermal Stability Of

AbstractAmorphous carbon (a-C) films are widely used as protective overcoats in many technology sectors, principally due to their excellent thermophysical properties and chemical inertness. The growth and thermal stability of sub-5-nm-thick a-C films synthesized by filtered cathodic vacuum arc on pure (crystalline) and nitrogenated (amorphous) silicon substrate surfaces were investigated in this study. Samples of a-C/Si and a-C/SiNx/Si stacks were thermally annealed for various durations and subsequently characterized by high-resolution transmission electron microscopy (TEM) and electron energy loss spectroscopy (EELS). The TEM images confirmed the continuity and uniformity of the a-C films and the 5-nm-thick SiNx underlayer formed by silicon nitrogenation using radio-frequency sputtering. The EELS analysis of cross-sectional samples revealed the thermal stability of the a-C films and the efficacy of the SiNx underlayer to prevent carbon migration into the silicon substrate, even after prolonged heating. The obtained results provide insight into the important attributes of an underlayer in heated multilayered media for preventing elemental intermixing with the substrate, while preserving the structural stability of the a-C film at the stack surface. An important contribution of this investigation is the establishment of an experimental framework for accurately assessing the thermal stability and elemental diffusion in layered microstructures exposed to elevated temperatures.

scholarly journals Physical networks from entropy-driven non-covalent interactions

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Anthony C. Yu ◽  
Huada Lian ◽  
Xian Kong ◽  
Hector Lopez Hernandez ◽  
Jian Qin ◽  
...  
Keyword(s):  
Elevated Temperatures ◽  
Dissociation Rate ◽  
Mathematical Framework ◽  
Temperature Dependent ◽  
Nanoparticle Interactions ◽  
Temperature Superposition ◽  
Non Covalent Interactions ◽  
Time Temperature Superposition ◽  
Covalent Interactions ◽  
Physical Crosslinking

AbstractPhysical networks typically employ enthalpy-dominated crosslinking interactions that become more dynamic at elevated temperatures, leading to network softening. Moreover, standard mathematical frameworks such as time-temperature superposition assume network softening and faster dynamics at elevated temperatures. Yet, deriving a mathematical framework connecting the crosslinking thermodynamics to the temperature-dependent viscoelasticity of physical networks suggests the possibility for entropy-driven crosslinking interactions to provide alternative temperature dependencies. This framework illustrates that temperature negligibly affects crosslink density in reported systems, but drastically influences crosslink dynamics. While the dissociation rate of enthalpy-driven crosslinks is accelerated at elevated temperatures, the dissociation rate of entropy-driven crosslinks is negligibly affected or even slowed under these conditions. Here we report an entropy-driven physical network based on polymer-nanoparticle interactions that exhibits mechanical properties that are invariant with temperature. These studies provide a foundation for designing and characterizing entropy-driven physical crosslinking motifs and demonstrate how these physical networks access thermal properties that are not observed in current physical networks.

Sign in / Sign up

Export Citation Format

Share Document