scholarly journals Design and Demonstration of Glass Panel Embedding for 3D System Packages for Heterogeneous Integration Applications

2019 ◽  
Vol 16 (3) ◽  
pp. 124-135 ◽  
Author(s):  
Siddharth Ravichandran ◽  
Shuhei Yamada ◽  
Tomonori Ogawa ◽  
Tailong Shi ◽  
Fuhan Liu ◽  
...  
Keyword(s):  
Form Factor ◽  
High Performance ◽  
Coefficient Of Thermal Expansion ◽  
Large Body ◽  
Electrical Performance ◽  
Heterogeneous Integration ◽  
Wafer Level ◽  
Glass Panel ◽  
Packaging Technology ◽  
3D Packaging

Abstract This article demonstrates a next-generation high-performance 3D packaging technology with smaller form factor, excellent electrical performance, and reliability for heterogeneous integration. High-density logic-memory integration, today, is built predominantly using interposers which are fundamentally limited in assembly pitch and interconnect lengths, and they also are expensive as the package sizes increase. On the other hand, high-frequency applications continue to use laminates which are also limited by package size and ability to integrate many components. Wafer-level fan-out (WLFO) packaging promises better performance and form factor at lower costs, but current WLFO packages are mold-based and hence are limited to small packages. This article presents a 3D packaging technology using glass panel embedding (GPE) for high-performance with potential for large body size heterogeneous integration applications. The tailorable coefficient of thermal expansion of glass allows a reliable direct board attach of large GPE packages that not only benefits the form factor and signal speed but also provides radical benefits to power delivery. Unlike interposers and silicon bridges, GPE packages are not bump-limited and can support I/O densities comparable with backend-of-line with silicon-like redistribution wiring at much lower costs. The fundamental limitations such as die shift and poor dimensional stability of current organic WLFO packages are addressed by parametric process improvements to reduce die shift to <2 μm while also improving the RDL surface planarity for high-yielding fine-line structures and integrating through glass via (TGV) in the fan-out region for 3D packaging. This article describes the fabrication process for 3D GPE, leading to demonstration of a technology using embedding of chips with all-Cu interconnections at 40-μm I/O pitch with TGVs at 300-μm pitch, thus enabling double-side RDL and assembly of chips to achieve three levels of device integration.

Design and demonstration of Glass Panel Embedding for 3D System Packages for heterogeneous integration applications

2018 ◽  
Vol 2018 (1) ◽  
pp. 000331-000336 ◽  
Author(s):  
Siddharth Ravichandran ◽  
Shuhei Yamada ◽  
Tomonori Ogawa ◽  
Tailong Shi ◽  
Fuhan Liu ◽  
...  
Keyword(s):  
Form Factor ◽  
High Performance ◽  
Power Delivery ◽  
Electrical Performance ◽  
Heterogeneous Integration ◽  
Glass Panel ◽  
Process Improvements ◽  
Fundamental Limitations ◽  
Device Integration ◽  
3D Packaging

Abstract This paper demonstrates a next generation high-performance 3D packaging architecture with smaller form factor, excellent electrical performance and reliability for heterogeneous integration. High density Logic-HBM integration, today, is built predominantly using interposers which are fundamentally limited in assembly pitch and interconnect lengths, and they also are expensive as the package sizes increase. On the other hand, high-frequency applications continue to use laminates which are again limited by package size and ability to integrate many components. WLFO promises better performance and form factor at lower costs, but current WLFO packages are mold-based and hence are limited to small packages. This paper presents the first demonstration of 3D Glass Panel Embedding (GPE) technology for high-performance large package applications involving heterogeneous integration. The tailorable CTE of glass allows a reliable direct board SMT of large GPE packages that not only benefits form factor and signal speed, but also provides radical benefits to power delivery. Unlike interposers and silicon bridges, GPE packages are not bump limited and can support BEOL-like I/O densities with Silicon-like RDL at much lower costs. The fundamental limitations like die-shift and poor dimensional stability of current organic WLFO packages are addressed by parametric process improvements to reduce die-shift to <2 um while also improving the RDL surface planarity for high-yielding fine-line structures. This paper describes the fabrication process for 3D GPE, leading to demonstration of a technology using embedding of chips with all-Cu interconnections at 40um I/O pitch while also enabling double-side assembly of chips to achieve 3 levels of device integration.

A Lithography-Based Compliant Chip-to-Substrate Wafer-Level Interconnect

2002 ◽  
Author(s):  
Qi Zhu ◽  
Lunyu Ma ◽  
Suresh K. Sitaraman
Keyword(s):  
High Performance ◽  
Coefficient Of Thermal Expansion ◽  
Low Cost ◽  
Optimization Technique ◽  
Cost Effective ◽  
Organic Substrate ◽  
Electrical Performance ◽  
Wafer Level ◽  
Good Reliability ◽  
Mechanical Compliance

As the rapid advances in IC design and fabrication continue to challenge and push the electronic packaging technology, in terms of fine pitch, high performance, low cost, and good reliability, compliant interconnects show great advantages for next-generation packaging. β-fly is designed as a compliant chip-to-substrate interconnect for performing wafer-level probing and for packaging without underfill. β-fly has good compliance in all directions to compensate the coefficient of thermal expansion (CTE) mismatch between the silicon die and an organic substrate. The fabrication of β-fly is similar to standard IC fabrication, and wafer-level packaging makes it cost effective. In this work, self-weight effect and stress distribution under planar displacement loading of β-fly is studied. The effect of geometry parameters on mechanical and electrical performance of β-fly is also studied. β-fly with thinner and narrower arcuate beams with larger radius and taller post is found to have better mechanical compliance. In addition to mechanical compliance, electrical characteristics of β-fly have also been studied in this work. However, it is found that structures with excellent mechanical compliance cannot have good electrical performance. Therefore, a trade off is needed for the design of β-fly. Response surface methodology and an optimization technique have been used to select the optimal β-fly structure parameters.

Advanced 3D eWLB-SiP (embedded Wafer Level Ball Grid Array – System in Package) Technology

2017 ◽  
Vol 2017 (DPC) ◽  
pp. 1-20
Author(s):  
Seung Wook Yoon
Keyword(s):  
Form Factor ◽  
Power Efficiency ◽  
High Performance ◽  
Electrical Characterization ◽  
Cost Effective ◽  
Electrical Performance ◽  
Wearable Electronics ◽  
Wafer Level ◽  
Low Profile ◽  
Line Spacing

FO-WLP (Fan-Out Wafer Level Packaging) has been established as one of the most versatile packaging technologies in the recent past and is already accounting for a market value of over 1 billion USD due to its unique advantages. The technology combines high performance, increased functionality with a high potential for heterogeneous integration and reduce the total form factor as well as cost-effectiveness. The emerging of advanced of silicon node technology down to 10 nanometer (nm) in support of higher performance, bandwidth and better power efficiency in mobile products pushes the boundaries of emerging packaging technologies to smaller form-factor packaging designs with finer line/spacing as well as improved thermal electrical/performance and integration of SiP or 3D capabilities. Advanced eWLB FO-WLP technology provides a versatile platform for the semiconductor industry's technology evolution from single or multi-die 2D package designs to 2.5D interposers and 3D System-in-Package (SiP) configurations. This paper reports developments that extend multi-die and 3D SiP applications with eWLB technology, including ultra thin devices or/and with an interposer substrate attachment. Test vehicles have been designed and fabricated to demonstrate and characterize integrated packaging solutions for network, mobile products including IoT and wearable electronics. The test vehicles have ranged from ~30mm2 to large sizes up to ~230mm2 and 0.4mm ball pitch. Assembly process details including 3D vertical interconnect, laser ablation, RDL processes and mechanical reliability characterizations are to be discussed with component and board level reliability results. In addition, warpage behavior and the PoP stacking process will also be presented. Innovative structure optimization that provides dual advantages of both height reduction and enhanced package reliability are reported. To enable higher interconnection density and signal routing, packages with multiple redistribution layers (RDL) and fine line/width spacing are fabricated and implemented on the eWLB platform. Successful reliability and electrical characterization results on multi-die and 3D eWLB-SiP configurations are reported as an enabling technology for highly integrated, miniaturized, low profile and cost effective solutions.

Wafer Level Assembly Technique Development for Fine Pitch Flip Chip 3D Die-to-Wafer Integration

2010 ◽  
Vol 2010 (1) ◽  
pp. 000548-000553
Author(s):  
Zhaozhi Li ◽  
Brian J. Lewis ◽  
Paul N. Houston ◽  
Daniel F. Baldwin ◽  
Eugene A. Stout ◽  
...  
Keyword(s):  
Flip Chip ◽  
Low Cost ◽  
Three Dimensional ◽  
Cost Effective ◽  
Market Demand ◽  
Wafer Level ◽  
Packaging Technology ◽  
Fine Pitch ◽  
3D Packaging ◽  
Assembly Technique

Three Dimensional (3D) Packaging has become an industry obsession as the market demand continues to grow toward higher packaging densities and smaller form factor. In the meanwhile, the 3D die-to-wafer (D2W) packaging structure is gaining popularity due to its high manufacturing throughput and low cost per package. In this paper, the development of the assembly process for a 3D die-to-wafer packaging technology, that leverages the wafer level assembly technique and flip chip process, is introduced. Research efforts were focused on the high-density flip chip wafer level assembly techniques, as well as the challenges, innovations and solutions associated with this type of 3D packaging technology. Processing challenges and innovations addressed include flip chip fluxing methods for very fine-pitch and small bump sizes; wafer level flip chip assembly program creation and yield improvements; and set up of the Pb-free reflow profile for the assembled wafer. 100% yield was achieved on the test vehicle wafer that has totally 1,876 flip chip dies assembled on it. This work has demonstrated that the flip chip 3D die-to-wafer packaging architecture can be processed with robust yield and high manufacturing throughput, and thus to be a cost effective, rapid time to market alternative to emerging 3D wafer level integration methodologies.

Development of G-Helix Structure as Off-Chip Interconnect

2004 ◽  
Vol 126 (2) ◽  
pp. 237-246 ◽  
Author(s):  
Qi Zhu ◽  
Lunyu Ma ◽  
Suresh K. Sitaraman
Keyword(s):  
Mechanical Performance ◽  
Coefficient Of Thermal Expansion ◽  
Mechanical Analysis ◽  
Organic Substrate ◽  
Electrical Performance ◽  
Wafer Level ◽  
Wafer Level Packaging ◽  
Package Weight ◽  
Mechanical Compliance ◽  
Cte Mismatch

Microsystem packages continue to demand lower cost, higher reliability, better performance and smaller size. Compliant wafer-level interconnects show great potential for next-generation packaging. G-Helix, an electroplated compliant wafer-level chip-to-substrate interconnect can facilitate wafer-level probing as well as wafer-level packaging without the need for an underfill. The fabrication of the G-Helix interconnect is similar to conventional IC fabrication process and is based on electroplating and photolithography. G-Helix interconnect has good mechanical compliance in the three orthogonal directions and can accommodate the differential displacement induced by the coefficient of thermal expansion (CTE) mismatch between the silicon die and the organic substrate. In this paper, we report the wafer-level fabrication of an area-arrayed G-Helix interconnects. The geometry effect on the mechanical compliance and electrical parasitics of G-Helix interconnects have been studied. Thinner and narrower arcuate beams with larger radius and taller post are found to have better mechanical compliance. However, it is also found that structures with excellent mechanical compliance may not have good electrical performance. Therefore, a trade off is needed. Using response surface methodology (RSM), an optimization has been done. Furthermore, reliability of the optimized G-helix interconnects in a silicon-on-organic substrate assembly has been assessed, which includes the package weight and thermo-mechanical analysis. The pitch size effect on the electrical and mechanical performance of G-Helix interconnects has also been studied.

A Heterogeneous Array of Off-Chip Interconnects for Optimum Mechanical and Electrical Performance

2007 ◽  
Vol 129 (4) ◽  
pp. 460-468 ◽  
Author(s):  
Karan Kacker ◽  
Thomas Sokol ◽  
Wansuk Yun ◽  
Madhavan Swaminathan ◽  
Suresh K. Sitaraman
Keyword(s):  
Flip Chip ◽  
Dielectric Material ◽  
Coefficient Of Thermal Expansion ◽  
Semiconductor Industry ◽  
Organic Substrate ◽  
Electrical Performance ◽  
Integrative Approach ◽  
Wafer Level ◽  
Target Values ◽  
Low K

Demand for off-chip bandwidth has continued to increase. It is projected by the Semiconductor Industry Association in their International Technology Roadmap for Semiconductors that by the year 2015, the chip-to-substrate area-array input-output interconnects will require a pitch of 80 μm. Compliant off-chip interconnects show great potential to address these needs. G-Helix is a lithography-based electroplated compliant interconnect that can be fabricated at the wafer level. G-Helix interconnects exhibit excellent compliance in all three orthogonal directions, and can accommodate the coefficient of thermal expansion (CTE) mismatch between the silicon die and the organic substrate without requiring an underfill. Also, these compliant interconnects are less likely to crack or delaminate the low-k dielectric material in current and future integrated circuits. The interconnects are potentially cost effective because they can be fabricated in batch at the wafer level and using conventional wafer fabrication infrastructure. In this paper, we present an integrative approach, which uses interconnects with varying compliance and thus varying electrical performance from the center to the edge of the die. Using such a varying geometry from the center to the edge of the die, the system performance can be tailored by balancing electrical requirements against thermomechanical reliability concerns. The test vehicle design to assess the reliability and electrical performance of the interconnects is also presented. Preliminary fabrication results for the integrative approach are presented and show the viability of the fabrication procedure. The results from reliability experiments of helix interconnects assembled on an organic substrate are also presented. Initial results from the thermal cycling experiments are promising. Results from mechanical characterization experiments are also presented and show that the out-of-plane compliance exceeds target values recommended by industry experts. Finally, through finite element analysis simulations, it is demonstrated that the die stresses induced by the compliant interconnects are an order of magnitude lower than the die stresses in flip chip on board (FCOB) assemblies, and hence the compliant interconnects are not likely to crack or delaminate low-k dielectric material.

Fine Pitch(40μm) Integration Platform for Flexible Hybrid Electronics using Fan-Out Wafer-level Packaging

2018 ◽  
Vol 2018 (1) ◽  
pp. 000064-000068
Author(s):  
Amir Hanna ◽  
Arsalan Alam ◽  
G. Ezhilarasu ◽  
Subramanian S. Iyer
Keyword(s):  
High Performance ◽  
Metal Films ◽  
Heterogeneous Integration ◽  
Wafer Level ◽  
Integration Platform ◽  
Wafer Level Packaging ◽  
Fine Pitch ◽  
Mechanical Bending

Abstract A flexible fan-out wafer-level packaging (FOWLP) process for heterogeneous integration of high performance dies in a flexible and biocompatible elastomeric package (FlexTrateTM) was used to assemble 625 dies with co-planarity and tilt <1μm, average die-shift of 3.28 μm with σ < 2.23 μm. Fine pitch interconnects (40μm pitch) were defined using a novel corrugated topography to mitigate the buckling phenomenon of metal films deposited on elastomeric substrates. Corrugated interconnects were then used to interconnect 200 dies, and then tested for cyclic mechanical bending reliability and have shown less than 7% change in resistance after bending down to 1 mm radius for 1,000 cycles.

CoC (Chip on Chip) or FtoF (Face to Face) - PossumTM Technology for 3D MEMS and ASIC eliminating the need of TSV or Wire Bonding

2013 ◽  
Vol 2013 (DPC) ◽  
pp. 000916-000936
Author(s):  
Jemmy Sutanto ◽  
D. H. Kang ◽  
J. H. Yoon ◽  
K. S. Oh ◽  
Michael Oh ◽  
...  
Keyword(s):  
Form Factor ◽  
System Integration ◽  
Wire Bonding ◽  
Electrical Performance ◽  
Wafer Level ◽  
3D Integration ◽  
Face To Face ◽  
Parasitic Resistance ◽  
On Chip ◽  
Packaging Cost

This paper describes the ongoing 3 years research and development at Amkor Technology on CoC (Chip on Chip)/FtF (Face to Face) – PossumTM technology. This technology has showed a lot of interests from the microelectronics customers/industries because of its various advantages, which include a) providing smaller form factor (SFF) to the final package, b) more functionalities (dies) can be incorporated/assembled in one package, c) improving the electrical performance - including lower parasitic resistance, lower power, and higher frequency bandwidth, and d) Opportunity for lower cost 3D system integration. Unlike other 3D Packaging technology (e.g. using TSV (Through Silicon Vias)) that requires some works in the front stream (wafer foundry) level, needs new capitals for machines/equipments, and needs modified assembly lines; CoC/FtF technology uses the existing flip Chip Attach (C/A) or TC (Thermal Compression) equipment/machine to perform the assembly joint between the two dies, which are named as the mother (larger) die and the daughter (smaller) die. Furthermore, the cost to assemble CoC/FtF is relatively inexpensive while the applications are very wide and endless, which include the 3D integration of MEMS and ASIC. The current MEMS packaging and test cost contributes about 35 to 45% to the overall MEMS unit cost. WLC (Wafer Level Capping) with wire bonding have been widely used for mass production for accelerometer (e.g. ADI and Motorola), gyroscope (e.g. Bosch and Invensense), and oscillator /timer (e.g. Discera). The WLC produce drawbacks of a large form factor and the increase in the capacitive and electrical resistances. Currently, the industries have been developing a new approach of 3D WLP (Wafer Level Packaging) by using a) TSV MEMS cap with wire bonding (e.g. Discera), b) TSV MAME cap with solder bump (e.g. Samsung, IMEC, and VTI), and c) TSV MEMS wafer/die with cap (e.g. Silex Microsystems). The needs of TSVs in the 3D WLP will add the packaging cost and reduce the design flexibility is pre-TSV wafer is used. “Amkor CoC/FtoF – PossumTM” is an alternative technology for 3D integration of MEMS and ASIC. CoC/FtoF – PossumTM does not require TSV or wire bonding; Miniaturizing form factor of 1.5 mm x 1.5 mm x 0.95 mm (including the package) of MEMS and ASIC can be achieved by using CoC/FtoF – PossumTM while Discera's design of 3D WLP requires substrate size > 2 mm x 2 mm. CoC/FtoF – PossumTM will likely produce packaging cost which is lower than WLC or 3D WLP – TSV at the same time the customer is benefited from smaller FF and reduced electrical/parasitic resistance. CoC/FtoF – PossumTM can be applied to any substrates including FCBGA and laminate. This technology also can be applied to package multiple MEMS microsensors, together with ASIC, microcontroller, and wireless RF to realize the 3D system integration.

Sign in / Sign up

Export Citation Format

Share Document