Dynamic Testing of Mechanical Properties of a Substrate Using Phase-Locked-Loop

2005 ◽  
Author(s):  
Matthew Clark ◽  
Z. C. Feng
Keyword(s):  
Mechanical Properties ◽  
Nonlinear Systems ◽  
Theoretical Result ◽  
Resonance Frequency ◽  
Mechanical Model ◽  
Dynamic Testing ◽  
Phase Locked Loop ◽  
System Frequency ◽  
The Relationship

This paper explores dynamically deriving the mechanical properties of a substrate. A method is presented in which a phase locked loop (PLL) is used to find the resonance frequency of a mechanical model consisting of an oscillating probe and a material substrate. This is done by first presenting an accurate PLL which is stable for nonlinear systems. The relationship between the system frequency and the stiffness of the material substrate is derived theoretically. The stiffness of the substrate is obtained by combining the theoretical result and the converging resonance frequency from PLL.

Synergetic improvement of mechanical properties and surface activities in γ-irradiated carbon fibers revealed by radial positioning spectroscopy and mechanical model

2018 ◽  
Vol 10 (5) ◽  
pp. 496-503 ◽  
Author(s):  
Mingjing Shan ◽  
Haibo Wang ◽  
Zhiwei Xu ◽  
Nan Li ◽  
Cheng Chen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Fibers ◽  
Mechanical Model ◽  
Surface Activities ◽  
The Relationship

The relationship between microstructures, surface activities, and mechanical properties of γ-irradiated carbon fibers has been evaluated quantitatively.

Actuation and dynamic mechanical characteristics of a core free flat dielectric electro-active polymer soft actuator

2020 ◽  
Vol 14 (4) ◽  
pp. 7396-7404
Author(s):  
Abdul Malek Abdul Wahab ◽  
Emiliano Rustighi ◽  
Zainudin A.
Keyword(s):  
Theoretical Model ◽  
Resonance Frequency ◽  
Dynamic Testing ◽  
Experimental Results ◽  
Percentage Error ◽  
Initial Tension ◽  
Average Percentage ◽  
Soft Actuator ◽  
Average Percentage Error ◽  
Mechanical Dynamics

Various complex shapes of dielectric electro-active polymer (DEAP) actuator have been promoted for several types of applications. In this study, the actuation and mechanical dynamics characteristics of a new core free flat DEAP soft actuator were investigated. This actuator was developed by Danfoss PolyPower. DC voltage of up to 2000 V was supplied for identifying the actuation characteristics of the actuator and compare with the existing formula. The operational frequency of the actuator was determined by dynamic testing. Then, the soft actuator has been modelled as a uniform bar rigidly fixed at one end and attached to mass at another end. Results from the theoretical model were compared with the experimental results. It was found that the deformation of the current actuator was quadratic proportional to the voltage supplied. It was found that experimental results and theory were not in good agreement for low and high voltage with average percentage error are 104% and 20.7%, respectively. The resonance frequency of the actuator was near 14 Hz. Mass of load added, inhomogeneity and initial tension significantly affected the resonance frequency of the soft actuator. The experimental results were consistent with the theoretical model at zero load. However, due to inhomogeneity, the frequency response function’s plot underlines a poor prediction where the theoretical calculation was far from experimental results as values of load increasing with the average percentage error 15.7%. Hence, it shows the proposed analytical procedure not suitable to provide accurate natural frequency for the DEAP soft actuator.

Sunlight exposure: the effects on the performance of paragliding fabric

2018 ◽  
Vol 69 (05) ◽  
pp. 381-389
Author(s):  
MENGÜÇ GAMZE SÜPÜREN ◽  
TEMEL EMRAH ◽  
BOZDOĞAN FARUK
Keyword(s):  
Mechanical Properties ◽  
Aging Process ◽  
Air Permeability ◽  
Sunlight Exposure ◽  
Test Results ◽  
Coating Materials ◽  
Strength Tests ◽  
Before And After ◽  
The Relationship ◽  
Dark Blue

This study was designed to explore the relationship between sunlight exposure and the mechanical properties of paragliding fabrics which have different colors, densities, yarn counts, and coating materials. This study exposed 5 different colors of paragliding fabrics (red, turquoise, dark blue, orange, and white) to intense sunlight for 150 hours during the summer from 9:00 a.m. to 3:00 p.m. for 5 days a week for 5 weeks. Before and after the UV radiation aging process, the air permeability, tensile strength, tear strength, and bursting strength tests were performed. Test results were also evaluated using statistical methods. According to the results, the fading of the turquoise fabric was found to be the highest among the studied fabrics. It was determined that there is a significant decrease in the mechanical properties of the fabrics after sunlight exposure. After aging, the fabrics become considerably weaker in the case of mechanical properties due to the degradation in both the dyestuff and macromolecular structure of the fiber

scholarly journals Water lubrication of graphene oxide-based materials

Friction ◽  
2021 ◽  
Author(s):  
Shaoqing Xue ◽  
Hanglin Li ◽  
Yumei Guo ◽  
Baohua Zhang ◽  
Jiusheng Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Graphene Oxide ◽  
Lubrication Theory ◽  
Lubricant Additives ◽  
Water Lubrication ◽  
Broad Application ◽  
Water Dispersibility ◽  
Metal Processing ◽  
The Relationship ◽  
Ph Concentration

AbstractWater is as an economic, eco-friendly, and efficient lubricant that has gained widespread attention for manufacturing. Using graphene oxide (GO)-based materials can improve the lubricant efficacy of water lubrication due to their outstanding mechanical properties, water dispersibility, and broad application scenarios. In this review, we offer a brief introduction about the background of water lubrication and GO. Subsequently, the synthesis, structure, and lubrication theory of GO are analyzed. Particular attention is focused on the relationship between pH, concentration, and lubrication efficacy when discussing the tribology behaviors of pristine GO. By compounding or reacting GO with various modifiers, amounts of GO-composites are synthesized and applied as lubricant additives or into frictional pairs for different usage scenarios. These various strategies of GO-composite generate interesting effects on the tribology behaviors. Several application cases of GO-based materials are described in water lubrication, including metal processing and bio-lubrication. The advantages and drawbacks of GO-composites are then discussed. The development of GO-based materials for water lubrication is described including some challenges.

Structure and properties of a phenylethynyl-terminated PMDA-type asymmetric polyimide

2018 ◽  
Vol 31 (3) ◽  
pp. 261-272 ◽  
Author(s):  
Yixiang Zhang ◽  
Masahiko Miyauchi ◽  
Steven Nutt
Keyword(s):  
Mechanical Properties ◽  
Thermal Processing ◽  
Amorphous Structure ◽  
Decomposition Temperature ◽  
Thermal And Mechanical Properties ◽  
Chain Mobility ◽  
Amorphous Structures ◽  
The Cross ◽  
Imide Oligomers ◽  
The Relationship

A new polymerized monomeric reactant (PMR)-type polyimide, designated TriA X, was investigated to determine polymer structure, processability, thermal, and mechanical properties and establish the relationship between the molecular structure and those properties. TriA X is a PMR-type polyimide with an asymmetric, irregular, and nonplanar backbone. Both the imide oligomers and the cross-linked polyimides of TriA X exhibited loose-packed amorphous structures, independent of thermal processing. The peculiar structures were attributed to the asymmetric backbone, which effectively prevented the formation of closed-packed chain stacking typically observed in polyimides. The imide oligomers exhibited a lower melt viscosity than a control imide oligomer (symmetric and semi-crystalline), indicating a higher chain mobility above the glass transition temperature ( Tg). The cured polyimide exhibited a Tg = 362°C and a decomposition temperature = 550°C. The cross-linked TriA X exhibited exceptional toughness and ductility (e.g. 15.1% at 23°C) for a polyimide, which was attributed to the high-molecular-weight oligomer and loose-packed amorphous structure. The thermal and mechanical properties of TriA X surpass those of PMR-15 and AFR-PE-4.

ANSYS Simply Supported Deep Beams Based on the Study of Mechanical Properties

2013 ◽  
Vol 351-352 ◽  
pp. 782-785
Author(s):  
Yong Bing Liu ◽  
Xiao Zhong Zhang
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Mechanical Model ◽  
Work Performance ◽  
Deep Beam ◽  
Analysis Software ◽  
Deep Beams ◽  
Element Analysis ◽  
Simply Supported ◽  
Force Characteristics

Established the mechanical model of simply supported deep beam, calculation and analysis of simple supported deep beams by using finite element analysis software ANSYS, simulated the force characteristics and work performance of the deep beam. Provides the reference for the design and construction of deep beams.

scholarly journals Experimental-numerical studies of the effect of cell structure on the mechanical properties of polypropylene foams

e-Polymers ◽  
2020 ◽  
Vol 20 (1) ◽  
pp. 713-723
Author(s):  
Wei Gong ◽  
Tuan-Hui Jiang ◽  
Xiang-Bu Zeng ◽  
Li He ◽  
Chun Zhang
Keyword(s):  
Mechanical Properties ◽  
Size Distribution ◽  
Cell Size ◽  
Cell Structure ◽  
Structure Parameters ◽  
Cell Size Distribution ◽  
Numerical Studies ◽  
Polypropylene Foam ◽  
The Impact ◽  
The Relationship

AbstractThe effects of the cell size and distribution on the mechanical properties of polypropylene foam were simulated and analyzed by finite element modeling with ANSYS and supporting experiments. The results show that the reduced cell size and narrow size distribution have beneficial influences on both the tensile and impact strengths. Decreasing the cell size or narrowing the cell size distribution was more effective for increasing the impact strength than the tensile strength in the same case. The relationship between the mechanical properties and cell structure parameters has a good correlation with the theoretical model.

Size Effect on Mechanical Properties of LVL

2014 ◽  
Vol 887-888 ◽  
pp. 824-829
Author(s):  
Qing Fang Lv ◽  
Ji Hong Qin ◽  
Ran Zhu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Size Effect ◽  
Tensile Test ◽  
Compression Test ◽  
Test Results ◽  
Laminated Veneer Lumber ◽  
Object Of Study ◽  
The Relationship

Laminated veneer lumber is taken as an object of study, and use LVL specimens of different sizes for compression test and tensile test. The goal of the experiment is to investigate the size effect on compressive strength and tensile strength as well as the influence of the secondary glued laminated face, which appears in the secondary molding processes. The results show that both compressive strength and tensile strength have the size effect apparently and the existence of the secondary glued laminated face lower the compressive strength of LVL specimens. Afterwards, the relationship between compressive strength and volume along with tensile strength and area are obtained by the test results.

A Study on Reaction Bonded Ceramics Fabricated by Silicon Infiltration to B4C Preforms

2012 ◽  
Vol 724 ◽  
pp. 343-346 ◽  
Author(s):  
Rong Zhen Liu ◽  
Qing Wen Duan ◽  
Wen Wei Gu ◽  
Hai Yun Jin ◽  
Shao Chun Xu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Theoretical Result ◽  
Boron Carbide ◽  
Theoretical Calculation ◽  
Vickers Hardness ◽  
Volume Expansion ◽  
Maximum Density ◽  
Infiltration Process

Silicon was infiltrated into B4C preforms to fabricate B4C based composites ceramics at 1600 °C under vacuum circumstance. In this paper, silicon infiltration process was discussed by theoretical calculation. The volume expansion caused by reactions between silicon and boron carbide was about 89.1% from the calculation. In our study, the maximum density of B4C preform for the infiltration of silicon was about 1.5g/cm3 which was larger than theoretical result. The results of mechanical behavior showed that B4C based composites had excellent mechanical properties with a density lower than 2.6g/cm3, Vickers-hardness of this material was 27.2GPa, and this material showed a flexural strength of 349MPa and fracture toughness of 3.8 MPa*m1/2.

Evaluating Mechanical Properties of Ceramics by Relative Methods

2007 ◽  
Vol 336-338 ◽  
pp. 2406-2410
Author(s):  
Yi Wang Bao ◽  
Xiao Xue Bu ◽  
Yan Chun Zhou ◽  
Li Zhong Liu
Keyword(s):  
Mechanical Properties ◽  
Material Properties ◽  
Ceramic Coatings ◽  
Relative Method ◽  
Tempered Glass ◽  
Theoretic Analysis ◽  
Surface Strength ◽  
Indirect Approach ◽  
Before And After ◽  
The Relationship

A relative method, defined as indirect approach to evaluate the material properties via the relationship between unknown properties and a known property, is proposed to estimate some properties that could not be measured by the traditional methods for ceramics. Experiments and theoretic analysis based on the relative method were carried out in this study to estimate the properties in following aspects: determining the temperature dependence of elastic modulus of some machineable ceramics by comparing the deflections; obtaining the modulus and strength of ceramic coatings supported by substrates, from the variation in properties of the rectangular beam samples before and after coating; estimating the residual stresses in tempered glass by comparing the change in the surface strength after strengthening.

Sign in / Sign up

Export Citation Format

Share Document