Heat-Insulating Composite Material Based on Wood and Polymer Waste

2020 ◽  
Vol 24 (2) ◽  
pp. 28-33 ◽  
Author(s):  
A.S. Kolosova ◽  
E.S. Pikalov ◽  
O.G. Selivanov
Keyword(s):  
Composite Material ◽  
Methylene Chloride ◽  
Experimental Studies ◽  
Raw Material ◽  
Insulation Material ◽  
Pressing Pressure ◽  
Regulatory Requirements ◽  
Deciduous Species ◽  
Waste Products ◽  
Polymer Waste

The results of the development of a raw mixture, which contains a filler obtained by grinding a mixture of small-sized wood waste based on light dirt varieties of coniferous and deciduous species, and a binder obtained by dissolving the waste products from polystyrene foam in methylene chloride, are presented. This mixture allows cold mixing and pressing followed by heat treatment at the boiling point of the solvent. In the course of experimental studies, the influence of the ratio of the mixture components and the pressing pressure on the basic properties and structure of the obtained composite material was established. The composition of the raw material mixture and the pressing were selected to ensure low thermal conductivity in combination with low values of water absorption and swelling density and strength compliant with regulatory requirements. Received thermal insulation material for construction purposes from wood and polymer waste, characterized by large volumes of formation and high rates of accumulation.

scholarly journals INTEGRATED PROCESSING TECHNOLOGY OF WASTES FROM CEREAL PRODUCTION

2019 ◽  
Vol 18 (4) ◽  
pp. 27-35
Author(s):  
N. KHORENGHY ◽  
A. LAPINSKA
Keyword(s):  
Technological Process ◽  
Experimental Studies ◽  
Raw Material ◽  
Biofuel Production ◽  
Technological Scheme ◽  
Waste Products ◽  
Fuel Pellets ◽  
Organic Solid ◽  
Barley Husk ◽  
Complex Technology

The article analyzes the structure of production of cereals in the country, it is established that during the processing of grain into grains a significant part of secondary material resources (flour and husk) is formed. Therefore, it is important to use husk of cereals as raw material for biofuel production. Different methods of producing organic solid biofuels have been analyzed, and it is shown that there are shortcomings of finished products - briquettes and pellets obtained without the use of binders, one of which is the problem of transportation over long distances, during which a considerable amount of compressed biofuel is destroyed due to an increase in humidity and, consequently, a decrease in their calorific values. Fuel pellets are mainly produced without addition, while for the production of briquettes with improved quality indicators, various additives and binders are used. The purpose of the work is to substantiate the complex technology of the processing of the waste of grain mills into pressed products. Object and object of research are formulated for achievement of the set goal. The object of research is the technological process of processing of waste of cereal mills, the regimes of certain technological processes, in particular preparation of binders. The subject of research is barley and barley husk, binders (barley glue). The use of starchy raw material - flour is suggested and grounded as a binder. On the basis of experimental studies, it has been proved that the most effective method is to prepare a paste of barley flour with a content of 15% CP followed by its introduction into biofuels in the amount of 5%. The article suggests and substantiates the complex technology of processing of cereal-based waste products into pressed products (fodder mixtures and biofuels), which includes the following technological lines: a pipeline preparation line; line of preparation for the binders; line of preparation of macro components; granulation line; briquetting line. The fuel pellets produced by this technology will have 1.13 kg / m3, fragility up to 10%. The scheme of the technological process of complex processing of cereal-based waste products into pressed products is presented. The principal technological scheme for the production of a granulated feed mixture or fuel pellets of feed is a holistic system within which the subsystems A, B, B, G1, D are interconnected. The principal technological scheme for the production of briquetted biofuels is a holistic system within which interconnections' The subsystems A, B, B, G, E function functioning seamlessly.

Recovery of Polymer Waste in the Production of Ceramics Veneer with a Self-glazing Effect

2021 ◽  
Vol 25 (6) ◽  
pp. 20-25
Author(s):  
E.A. Pavlycheva ◽  
E.S. Pikalov ◽  
O.G. Selivanov
Keyword(s):  
Energy Efficiency ◽  
Titanium Dioxide ◽  
Boric Acid ◽  
Water Absorption ◽  
Frost Resistance ◽  
Raw Material ◽  
Material Base ◽  
Vitreous Phase ◽  
Waste Products ◽  
Polymer Waste

The results of studies on the development of the composition of the charge based on low-plasticity clay using waste products from the consumption of products made of unplasticized polyvinyl chloride are presented. In addition, boric acid as a flux and titanium dioxide as a source of the vitreous phase are introduced into the composition of the charge to obtain the effects of vitrification of the surface of ceramic particles and self-glazing of the surface of the samples. The dependences of the main properties of ceramics veneer on the ratio between the amounts of polymer waste and titanium dioxide with the introduction of 5% by weight of boric acid have been established. The quantities of charge components that ensure the energy efficiency of the developed ceramics while ensuring strength, water absorption and frost resistance at a level corresponding to the requirements for products for brick cladding of buildings and structures have been determined. The use of this composition expands the range and raw material base for the production of ceramics veneer, allow you to dispose of polymer waste at any degree of purity and destruction in sufficiently large quantities.

Applications of Bentonite to Soil Decontamination

2018 ◽  
Vol 69 (7) ◽  
pp. 1695-1698
Author(s):  
Marin Rusanescu ◽  
Carmen Otilia Rusanescu ◽  
Gheorghe Voicu ◽  
Mihaela Begea
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Laboratory Experiments ◽  
Experimental Studies ◽  
Heavy Metal Concentration ◽  
Polluted Soil ◽  
Raw Material ◽  
Soil Decontamination ◽  
Metal Retention ◽  
Removal Of Heavy Metals

A calcium bentonite from Orasu Nou deposit (Satu Mare Romania) was used as raw material. We have conducted laboratory experiments to determine the influence of bentonite on the degree of heavy metal retention. It has been observed that the rate of retention increases as the heavy metal concentration decreases. Experimental studies have been carried out on metal retention ( Zn) in bentonite. In this paper, we realized laboratory experiments for determining the influence of metal (Zn) on the growth and development of two types of plants (Pelargonium domesticum and Kalanchoe) and the effect of bentonite on the absorption of pollutants. These flowers were planted in unpolluted soil, in heavy metal polluted soil and in heavy metal polluted soil to which bentonite was added to observe the positive effect of bentonite. It has been noticed that the flowers planted in unpolluted soil and polluted with heavy metals to which bentonite has been added, the flowers have flourished, the leaves are still green and the plants whose soils have been polluted with heavy metals began to dry after 6 days, three weeks have yellowish leaves and flowers have dried. Experiments have demonstrated the essential role of bentonite for the removal of heavy metals polluted soil.

The system of indicators of the quality of the carbon-carbon composite materials and technologies of their production

2018 ◽  
pp. 127-132
Author(s):  
T. N. Antipova ◽  
D. S. Shiroyan
Keyword(s):  
Composite Material ◽  
Low Cost ◽  
Experimental Studies ◽  
Carbon Matrix ◽  
Carbon Composite ◽  
Optimal Number ◽  
Laboratory Equipment ◽  
Carbon Composite Material ◽  
Carbon Composite Materials

The system of indicators of quality of carbon-carbon composite material and technological operations of its production is proved in the work. As a result of the experimental studies, with respect to the existing laboratory equipment, the optimal number of cycles of saturation of the reinforcing frame with a carbon matrix is determined. It was found that to obtain a carbon-carbon composite material with a low cost and the required quality indicators, it is necessary to introduce additional parameters of the pitch melt at the impregnation stage.

scholarly journals Study of the Physical Behavior of a New Composite Material Based on Fly Ash from the Combustion of Coal in an Ultra-Supercritical Thermal Power Plant

2021 ◽  
Vol 5 (6) ◽  
pp. 151
Author(s):  
Mustapha El Kanzaoui ◽  
Chouaib Ennawaoui ◽  
Saleh Eladaoui ◽  
Abdelowahed Hajjaji ◽  
Abdellah Guenbour ◽  
...  
Keyword(s):  
Composite Material ◽  
Fly Ash ◽  
Power Plant ◽  
High Performance ◽  
Thermal Power ◽  
Recovery Process ◽  
Industrial Wastes ◽  
Raw Material ◽  
Polymerization Reaction ◽  
High Performance Composite

Given the amount of industrial waste produced and collected in the world today, a recycling and recovery process is needed. The study carried out on this subject focuses on the valorization of one of these industrial wastes, namely the fly ash produced by an ultra-supercritical coal power plant. This paper describes the use and recovery of fly ash as a high percentage reinforcement for the development of a new high-performance composite material for use in various fields. The raw material, fly ash, comes from the staged combustion of coal, which occurs in the furnace of an ultra-supercritical boiler of a coal-fired power plant. Mechanical compression, thermal conductivity, and erosion tests are used to study the mechanical, thermal, and erosion behavior of this new composite material. The mineralogical and textural analyses of samples were characterized using Scanning Electron Microscopy (SEM). SEM confirmed the formation of a new composite by a polymerization reaction. The results obtained are very remarkable, with a high Young’s modulus and a criterion of insulation, which approves the presence of a potential to be exploited in the different fields of materials. In conclusion, the composite material presented in this study has great potential for building material and could represent interesting candidates for the smart city.

scholarly journals Rheological and Microbiological Characteristics of Hops and Hot Trub Particles Formed during Beer Production

Molecules ◽  
2021 ◽  
Vol 26 (3) ◽  
pp. 681
Author(s):  
Monika Sterczyńska ◽  
Marek Zdaniewicz ◽  
Katarzyna Wolny-Koładka
Keyword(s):  
Rheological Properties ◽  
Raw Materials ◽  
Raw Material ◽  
Microbiological Analysis ◽  
Waste Products ◽  
Low Viscosity ◽  
Post Process ◽  
High Shear Rates ◽  
Different Temperatures ◽  
Beer Production

During the production of beer, and especially beer wort, the main wastes are spent grain and hot trub, i.e., the so-called “hot break.” Combined with yeast after fermentation, they represent the most valuable wastes. Hot trub is also one of the most valuable by-products. Studies on the chemical composition of these sediments and their rheological properties as waste products will contribute to their effective disposal and even further use as valuable pharmaceutical and cosmetic raw materials. So far, hot trub has been studied for morphology and particle distribution depending on the raw material composition and beer wort extract. However, there are no preliminary studies on the rheological properties of hot trub and hops. In particular, no attention has yet been paid to the dependence of these properties on the hop variety or different protein sources used. The aim of this study was to examine the effect of different hopping methods on hot trub viscosity and beer wort physicochemical parameters. Additionally, the hop solutions were measured at different temperatures. A microbiological analysis of hop sediments was also performed to determine the post-process survival of selected microorganisms in these wastes. For manufacturers of pumps used in the brewing industry, the most convenient material is that of the lowest viscosity. Low viscosity hot trub can be removed at lower velocities, which reduces costs and simplifies washing and transport. The sediments also had similar equilibrium viscosity values at high shear rates.

scholarly journals A Novel Approach to Fabricate Foam Ceramics from Steel Slag

2020 ◽  
Vol 2020 ◽  
pp. 1-7
Author(s):  
Yu Zheng ◽  
Xudong Luo ◽  
Jinlong Yang ◽  
Wenlong Huo ◽  
Chi Kang
Keyword(s):  
Compressive Strength ◽  
Ph Value ◽  
Steel Slag ◽  
Raw Material ◽  
Solid Loading ◽  
Insulation Material ◽  
Ceramic Foams ◽  
Novel Approach ◽  
The Stability ◽  
First Time

A novel approach is used for fabricating steel slag foam ceramics based on the particle-stabilized foaming method. In this work, steel slag was used as the raw material and propyl gallate (PG) was used as the surface modifier. For the first time, steel slag ceramic foams were successfully fabricated based on particle-stabilized foams. The results show that the stability of the ceramic foams was closely related to the pH value and PG concentration. The porosity and compressive strength could be controlled by changing the solid loading of steel slag and sintering temperature. The porosity of steel slag foam ceramics ranged from 85.6% to 62.53%, and the compressive strength was from 1.74 MPa to 10.42 MPa. The thermal conductivity of steel slag foam ceramics was only 0.067 W (m·K)−1, which shows that it could be used as a thermal insulation material.

scholarly journals Characterization and Analysis of the Carbonation Process of a Lime Mortar Obtained from Phosphogypsum Waste

2021 ◽  
Vol 18 (12) ◽  
pp. 6664
Author(s):  
María Isabel Romero-Hermida ◽  
Antonio María Borrero-López ◽  
Vicente Flores-Alés ◽  
Francisco Javier Alejandre ◽  
José María Franco ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mineralogical Composition ◽  
Barium Sulphate ◽  
Negative Influence ◽  
Raw Material ◽  
Porous System ◽  
Waste Products ◽  
Liesegang Rings ◽  
Carbonation Process ◽  
Ultrasonic Propagation

This work addresses the reuse of waste products as a raw material for lime putties, which are one of the components of mortar. 1:3 Lime/sand mortars very similar to conventional construction mortars were prepared using a lime putty obtained from the treatment of phosphogypsum with sodium hydroxide. The physical, rheological and mechanical properties of this phosphogypsum-derived mortar have been studied, as well as the mineralogical composition, microstructure by scanning electron microscope (SEM) and curing process by monitoring carbonation and ultrasonic propagation velocity. Considering the negative influence of sulphates on the hardened material, the behaviour of the material after sulphates precipitation by adding barium sulphate was additionally tested. Carbonation progressed from the outside to the inside of the specimen through the porous system by Liesegang rings patterns for mortars with soluble sulphates, while the carbonation with precipitated sulphates was controlled by diffusion-precipitation. Overall, the negative influence of low-sulphate contents on the mechanical properties of mortars was verified. It must be highlighted the importance of their precipitation to obtain adequate performance.

Studying the Effect of some Factors on the Stress-Strain Behavior of the Rostov Region Limestones in the Course of their Production and Use

2021 ◽  
Vol 1022 ◽  
pp. 80-86
Author(s):  
Mikhail G. Kholodnyak ◽  
Sergey A. Stelmakh ◽  
Evgeniy M. Shcherban ◽  
Mukhuma P. Nazhuev
Keyword(s):  
Construction Material ◽  
Experimental Studies ◽  
Raw Material ◽  
Material Base ◽  
Strain Behavior ◽  
Current State ◽  
Rostov Region ◽  
Literary Sources ◽  
Crushed Granite ◽  
Strain Stress

The paper considers the current state of the mineral raw material base and the construction material market of the Rostov Region. The effect of various factors on the strain-stress behavior of local limestones has been investigated. The scientific and technical literary sources devoted to the processes of rock failure under various loads have been analyzed. The experimental studies have shown that the tested samples of limestone with a high content of cuboidal grains have characteristics comparable to those of the crushed granite stone. It has been concluded that the use of the Rostov Region limestones in the construction industry is competitive and feasible, provided the proper implementation of the engineering measures proposed in their production.

Sign in / Sign up

Export Citation Format

Share Document