A New Keeper Domino Logic Based Full Adder for High Speed Arithmetic Circuits

2020 ◽  
Vol 12 ◽  
Author(s):  
Deepika Bansal ◽  
Bal Chand Nagar ◽  
Ajay Kumar ◽  
Brahamdeo Prasad Singh
Keyword(s):  
Power Consumption ◽  
High Speed ◽  
High Efficiency ◽  
Dynamic Logic ◽  
Full Adder ◽  
Leakage Power ◽  
Low Leakage ◽  
Dynamic Circuits ◽  
Power Delay Product ◽  
Domino Circuits

Objective: A new efficient keeper circuit has been proposed in this article for achieving low leakage power consumption and to improve power delay product of the dynamic logic using carbon nanotube MOSFET. Method: As a benchmark, an one-bit adder has been designed and characterized with both technologies Si-MOSFET and CN-MOSFET using proposed and existing dynamic circuits. Furthermore, a comparison has been made to demonstrate the superiority of CN-MOSFET technology with Synopsys HSPICE tool for multiple bit adders available in the literature. Result: The simulation results show that the proposed keeper circuit provides lower static and dynamic power consumption up to 57 and 40% respectively, as compared to the domino circuits using 32nm CN-MOSFET technology provided by Stanford University. Moreover, the proposed keeper configuration provides better performance using SiMOSFET and CN-MOSFET technologies. Conclusion: A comparison of the proposed keeper with previously published designs is also given in terms of power consumption, delay and power delay product with the improvement up to 75, 18 and 50% respectively. The proposed circuit uses only two transistors, so it requires less area and gives high efficiency.

Low Power Wide Fan-in Domino OR Gate Using CN-MOSFETs

2020 ◽  
Vol 10 (1) ◽  
pp. 55-62
Author(s):  
Deepika Bansal ◽  
Bal Chand Nagar ◽  
Brahamdeo Prasad Singh ◽  
Ajay Kumar
Keyword(s):  
Power Consumption ◽  
High Performance ◽  
Dynamic Logic ◽  
Clock Frequency ◽  
Charge Sharing ◽  
Benchmark Circuit ◽  
Domino Circuit ◽  
Power Delay Product ◽  
Domino Circuits ◽  
Or Gate

Background & Objective: In this paper, a modified pseudo domino configuration has been proposed to improve the leakage power consumption and Power Delay Product (PDP) of dynamic logic using Carbon Nanotube MOSFETs (CN-MOSFETs). The simulations for proposed and published domino circuits are verified by using Synopsys HSPICE simulator with 32nm CN-MOSFET technology which is provided by Stanford. Methods: The simulation results of the proposed technique are validated for improvement of wide fan-in domino OR gate as a benchmark circuit at 500 MHz clock frequency. Results: The proposed configuration is suitable for cascading of the high performance wide fan-in circuits without any charge sharing. Conclusion: The performance analysis of 8-input OR gate demonstrate that the proposed circuit provides lower static and dynamic power consumption up to 62 and 40% respectively, and PDP improvement is 60% as compared to standard domino circuit.

scholarly journals Ultra high speed full adder for biomedical applications

2021 ◽  
Vol 10 (1) ◽  
pp. 25
Author(s):  
Basavoju Harish ◽  
M. S. S. Rukmini
Keyword(s):  
Power Consumption ◽  
High Speed ◽  
High Performance ◽  
Supply Voltage ◽  
Medical Engineering ◽  
Digital Signal ◽  
Full Adder ◽  
Digital Devices ◽  
Ripple Carry Adder ◽  
Power Delay Product

In the field of bio medical engineering high performance CPU for digital signal processing plays a significant role. Frequency efficient circuit is a paramount requirement for the portable digital devices employing various digital processors. In this work a novel high speed one-bit 10T full adder with complemented output was described. The circuit was constructed with XOR gates which were built using two CMOS transistors. The XOR gate was constructed using 2T multiplexer circuit style. It was observed that power consumption of the designed circuit at 180nm with supply voltage 1.8V is 183.6 uW and delay was 1.809 ps whereas power consumption at 90nm with supply voltage 1.2V is 25.74 uW and delay was 8.245 ps. The observed Power Delay Product (PDP) in 180nm (at supply voltage 1.8V) is 0.33 and in 90nm (at supply voltage 1.2V) is 0.212. The work was extended by implementing a 32-bit Ripple Carry Adder (RCA) and was found that the delay at 180nm is 93.7ps and at 90nm is 198ps. The results were drawn at 180nm and also 90nm technology using CAD tool. The results say that the present work offered significant enhancement in speed and PDP compared with existing designs.

Sleep signal controlled footless domino circuit for low leakage current

Circuit World ◽  
2018 ◽  
Vol 44 (2) ◽  
pp. 87-98
Author(s):  
Amit Kumar Pandey ◽  
Tarun Kumar Gupta ◽  
Pawan Kumar Verma
Keyword(s):  
Power Consumption ◽  
Threshold Voltage ◽  
Leakage Power ◽  
Content Type ◽  
Control Techniques ◽  
Low Leakage ◽  
Domino Circuit ◽  
Dual Threshold Voltage ◽  
Domino Circuits ◽  
Sleep Control

Purpose This paper aims to propose a new sleep signal controlled footless domino circuit for reducing the subthreshold and gate oxide leakage currents. Design/methodology/approach In the proposed circuit, a P channel MOSFET (PMOS) sleep switch transistor is inserted between the power supply and the output node. The sleep transistor, the source of the pull-down network, and the source of the N channel MOSFET (NMOS) transistor of the output inverter are controlled by this additional sleep signal to place the footless domino circuit in a low leakage state. Findings The authors simulate the proposed circuit by using HSPICE in 45-nm CMOS technology for OR and AND logic gates such as OR2, OR4, OR8, AND2 and AND4 at 25°C and 110°C. The proposed circuit reduces leakage power consumption as compared to the existing circuits. Originality/value The proposed circuit significantly reduces the total leakage power consumption up to 99.41 and 99.51 per cent as compared to the standard dual-threshold voltage footless domino circuits at 25°C and 110°C, respectively, and up to 93.79 and 97.98 per cent as compared to the sleep control techniques at 25°C and 110°C, respectively. Similarly, the proposed circuit reduces the active power consumption up to 26.76 and 86.25 per cent as compared to the standard dual-threshold voltage and sleep control techniques footless domino circuits at 25°C and 110°C, respectively.

Improved Domino Logic Circuits and its Application in Wide Fan-In OR Gates

2020 ◽  
Vol 12 (1) ◽  
pp. 58-67
Author(s):  
Deepika Bansal ◽  
Bal Chand Nagar ◽  
Brahamdeo Prasad Singh ◽  
Ajay Kumar
Keyword(s):  
Power Consumption ◽  
High Speed ◽  
High Performance ◽  
Voltage Drop ◽  
Main Concern ◽  
Clock Frequency ◽  
Domino Logic ◽  
Evaluation Phase ◽  
Power Delay Product ◽  
Domino Circuits

Background: Main concern in efficient VLSI circuit designing is low-power consumption, high-speed and noise tolerance capability. Objective: In this paper, two efficient and high-performance topologies are proposed for cascaded domino logic using carbon nanotube MOSFETs (CN-MOSFETs). The first topology is designed to remove the intermediate charge sharing problem without any keeper circuit, whereas the second one holds the true logic level of the evaluation phase without any voltage drop for next precharge phase. The proposed topologies are suitable for cascading of the high-performance domino circuits. Methods: The proposed domino circuits are tested and verified using Synopsys HSPICE simulator with 32nm CN-MOSFET technology provided by Stanford University. Conclusion: The power delay product of proposed DL-I and DL-II improves by 32.59 % and 40.98 % for 8-input OR gate as compared to standard logic respectively at the clock frequency of 500 MHz. The simulation results validate that the proposed circuits improve the performance of pseudo domino logic with respect to leakage power consumption, delay and unity noise gain.

Performance Analysis of Various Multipliers Using 8T-full Adder with 180nm Technology

2020 ◽  
Vol 13 (6) ◽  
pp. 864-870
Author(s):  
Sai Venkatramana Prasada G.S ◽  
G. Seshikala ◽  
S. Niranjana
Keyword(s):  
Low Power ◽  
Power Dissipation ◽  
High Speed ◽  
High Performance ◽  
Full Adder ◽  
Fundamental Operation ◽  
Wallace Tree ◽  
Power Delay Product ◽  
The Comparative Study ◽  
Wallace Tree Multiplier

Background: This paper presents the comparative study of power dissipation, delay and power delay product (PDP) of different full adders and multiplier designs. Methods: Full adder is the fundamental operation for any processors, DSP architectures and VLSI systems. Here ten different full adder structures were analyzed for their best performance using a Mentor Graphics tool with 180nm technology. Results: From the analysis result high performance full adder is extracted for further higher level designs. 8T full adder exhibits high speed, low power delay and low power delay product and hence it is considered to construct four different multiplier designs, such as Array multiplier, Baugh Wooley multiplier, Braun multiplier and Wallace Tree multiplier. These different structures of multipliers were designed using 8T full adder and simulated using Mentor Graphics tool in a constant W/L aspect ratio. Conclusion: From the analysis, it is concluded that Wallace Tree multiplier is the high speed multiplier but dissipates comparatively high power. Baugh Wooley multiplier dissipates less power but exhibits more time delay and low PDP.

scholarly journals A high-speed hybrid Full Adder with low power consumption

2012 ◽  
Vol 9 (24) ◽  
pp. 1900-1905
Author(s):  
Kamran Delfan Hemmati ◽  
Mojtaba Behzad Fallahpour ◽  
Abbas Golmakani ◽  
Kamyar Delfan Hemmati
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
High Speed ◽  
Full Adder ◽  
Low Power Consumption

scholarly journals High-Speed Hybrid-Logic Full Adder Using High-Performance 10-T XOR–XNOR Cell

2021 ◽  
pp. 263-269
Author(s):  
Tejaswini M. L ◽  
Aishwarya H ◽  
Akhila M ◽  
B. G. Manasa
Keyword(s):  
High Speed ◽  
High Performance ◽  
Full Adder ◽  
Cmos Technology ◽  
Power Performance ◽  
High Speed Design ◽  
Power Delay Product ◽  
Full Swing ◽  
Output Swing ◽  
High Output

The main aim of our work is to achieve low power, high speed design goals. The proposed hybrid adder is designed to meet the requirements of high output swing and minimum power. Performance of hybrid FA in terms of delay, power, and driving capability is largely dependent on the performance of XOR-XNOR circuit. In hybrid FAs maximum power is consumed by XOR-XNOR circuit. In this paper 10T XOR-XNOR is proposed, which provide good driving capabilities and full swing output simultaneously without using any external inverter. The performance of the proposed circuit is measured by simulating it in cadence virtuoso environment using 90-nm CMOS technology. This circuit outperforms its counterparts showing power delay product is reduced than that of available XOR-XNOR modules. Four different full adder designs are proposed utilizing 10T XOR-XNOR, sum and carry modules. The proposed FAs provide improvement in terms of PDP than that of other architectures. To evaluate the performance of proposed full adder circuit, we embedded it in a 4-bit and 8-bit cascaded full adder. Among all FAs two of the proposed FAs provide the best performance for a higher number of bits.

scholarly journals Novel Design of Low-Power High-Speed Hybrid Full Adder Design using Gate Diffusion Input (GDI) Technique

2020 ◽  
Vol 9 (12) ◽  
pp. 323-328
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
High Speed ◽  
Critical Path ◽  
Circuit Simulation ◽  
Full Adder ◽  
Cmos Process ◽  
Path Delay ◽  
Process Technology ◽  
Xnor Gate

VLSI technology become one of the most significant and demandable because of the characteristics like device portability, device size, large amount of features, expenditure, consistency, rapidity and many others. Multipliers and Adders place an important role in various digital systems such as computers, process controllers and signal processors in order to achieve high speed and low power. Two input XOR/XNOR gate and 2:1 multiplexer modules are used to design the Hybrid Full adders. The XOR/XNOR gate is the key punter of power included in the Full adder cell. However this circuit increases the delay, area and critical path delay. Hence, the optimum design of the XOR/XNOR is required to reduce the power consumption of the Full adder Cell. So a 6 New Hybrid Full adder circuits are proposed based on the Novel Full-Swing XOR/XNOR gates and a New Gate Diffusion Input (GDI) design of Full adder with high-swing outputs. The speed, power consumption, power delay product and driving capability are the merits of the each proposed circuits. This circuit simulation was carried used cadence virtuoso EDA tool. The simulation results based on the 90nm CMOS process technology model.

Designing of Low-Power High-Speed Noise Immune CNTFET 1-Trit Unbalanced Ternary Subtractor

2021 ◽  
Author(s):  
Yogesh Shrivastava ◽  
Tarun Kumar Gupta
Keyword(s):  
Power Consumption ◽  
High Speed ◽  
Noise Analysis ◽  
Average Power ◽  
Noise Margin ◽  
Average Power Consumption ◽  
Effect Transistor ◽  
Power Delay Product ◽  
Static Noise ◽  
Made In

Ternary logic has been demonstrated as a superior contrasting option to binary logic. This paper presents a ternary subtractor circuit in which the input signal is converted into binary. The proposed design is implemented using Carbon Nanotube Field Effect Transistor (CNTFET), a forefront innovation. A correlation has been made in the proposed design on parameters like Power-Delay Product (PDP), Energy Delay Product (EDP), average power consumption, delay and static noise margin. Every one of these parameters is obtained by simulating the circuits on the HSPICE simulator. The proposed design indicates an improvement of 60.14%, 59.34%, 74.98% and 84.28%, respectively, in power consumption, delay, PDP and EDP individually in correlation with recent designs. The increased carbon nanotubes least affect the proposed subtractor design. In noise analysis, the proposed design outperformed all the existing designs.

A Low Power - High Speed CNTFETs Based Full Adder Cell With Overflow Detection

2019 ◽  
Vol 11 (1) ◽  
pp. 80-87 ◽  
Author(s):  
Jitendra Kumar Saini ◽  
Avireni Srinivasulu ◽  
Renu Kumawat
Keyword(s):  
Mass Production ◽  
High Speed ◽  
Field Effect Transistor ◽  
Full Adder ◽  
Enabling Technology ◽  
Look Ahead ◽  
Ripple Carry Adder ◽  
Effect Transistor ◽  
Cad Tool ◽  
Power Delay Product

The transformation from the development of enabling technology to mass production of consumer-centric semiconductor products has empowered the designers to consider characteristics like robustness, compactness, efficiency, and scalability of the product as implicit pre-cursors. The Carbon Nanotube Field Effect Transistor (CNFET) is the present day technology. In this manuscript, we have used CNFET as the enabling technology to design a 1-bit Full Adder (1b-FA16) with overflow detection. The proposed 1b-FA16 is designed using 16 transistors. Finally, the proposed 1b-FA16 is further used to design a Ripple Carry Adder (RCA), Carry Look Ahead Adder (CLA) circuit and RCA with overflow bit detection. Methods and Results: The proposed 1b-FA16 circuit was designed with CNFET technology simulated at 32 nm with a voltage supply of +0.9 V using the Cadence Virtuoso CAD tool. The model used is Stanford PTM. Comparison of the existing full adder designs with the proposed 1b-FA16 design was done to validate the improvements in terms of power, delay and Power Delay Product (PDP). Table 2, shows the results of comparison for the proposed 1b-FA16 with the existing full adder designs implemented using CNFET for parameters like power, delay and power delay product. Conclusion: It can be concluded that the proposed 1b-FA16 yielded better results as compared to the existing full adder designs implemented using CNFET. The improvement in power, delay and power delay product was approximately 11%, 9% and 24% respectively. Hence, the proposed circuit implemented using CNFET gives a substantial rate of improvements over the existing circuits.

Sign in / Sign up

Export Citation Format

Share Document