Sample Preparation for Backside Failure Analysis Using Infrared Photoemission Microscopy

1999 ◽  
Author(s):  
Alastair Trigg ◽  
Peak Yong Loh
Keyword(s):  
Surface Roughness ◽  
Sample Preparation ◽  
Failure Analysis ◽  
Die Surface ◽  
Heavily Doped

Abstract For conventional photoemission microscopy the silicon is thinned to a few tens of micrometres for backside imaging since silicon is opaque in the visble part of the spectrum. However, at wavelengths greater than approximately 1050 nm, most silicon is effectively transparent. Hence, the use of an infrared photoemission microscope (IRPEM) operating at wavelengths of 1100 to 2500 nm, usually eliminates the need for thinning, except where the silicon is heavily doped. However, the plastic encapsulation of packaged devices must be removed and the die surface polished. A polishing system has been evaluated and optimised for this purpose. Surface roughness (Ra) of 1 nm or better was obtained. Representative applications are shown and discussed.

Novel Failure Analysis Sample Preparation Techniques for PoP Packaging

2012 ◽  
Author(s):  
Ng Sea Chooi ◽  
Chor Theam Hock ◽  
Ma Choo Thye ◽  
Khoo Poh Tshin ◽  
Dan Bockelman
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Failure Mechanisms ◽  
Preparation Process ◽  
Space Saving ◽  
Optical Probing ◽  
Preparation Techniques

Abstract Trends in the packaging of semiconductors are towards miniaturization and high functionality. The package-on-package(PoP) with increasing demands is beneficial in cost and space saving. The main failure mechanisms associated with PoP technology, including open joints and warpage, have created a lot of challenges for Assembly and Failure Analysis (FA). This paper outlines the sample preparation process steps to overcome the challenges to enable successful failure analysis and optical probing.

Basic Physics in Color-Coded EOS Metallization Failures (Differentiating between EOS and ESD)

1998 ◽  
Author(s):  
Leo G. Henry ◽  
J.H. Mazur
Keyword(s):  
Failure Analysis ◽  
Light Microscope ◽  
Structural Changes ◽  
Surface Oxide ◽  
Aluminum Surface ◽  
Surrounding Area ◽  
Die Surface ◽  
Basic Physics ◽  
Direct Contrast ◽  
Glass Interface

Abstract The task of differentiating precisely between EOS and ESD failures continues to be a challenging one for Failure Analysis Engineers. Electrical OverStress (EOS) failures on the die surface (burnt/fused metallization) of an IC can be characterized mainly by the discoloration at the site of the failures. This is in direct contrast to the lack of discoloration characteristic of ESD failures, which occur almost exclusively below the die surface (oxide and junction failures). To aid in this distinction, this paper attempts to present the underlying physics behind the discoloration produced in the EOS failures. For the EOS failures, the metal fuses due to the longer pulse widths (sec to msec), while for the ESD failures, the silicon melts because of the shorter pulse widths (< < 500 nsec) and higher energy. After EOS, the aluminum surface becomes dark and rough and the oxide in the surrounding area becomes deformed and distorted, resulting in the discoloration observed in the light microscope. This EOS discoloration could be due to one or more of the following: 1) morphological and structural changes at the metal/glass interface and the glass itself; 2) changes in the thickness and scattering behavior of the glass and metal in the failed areas.

Thin-Die Flip Chip Physical-FA Process Flow

2002 ◽  
Author(s):  
Andrew J. Komrowski ◽  
N. S. Somcio ◽  
Daniel J. D. Sullivan ◽  
Charles R. Silvis ◽  
Luis Curiel ◽  
...  
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Flip Chip ◽  
Semiconductor Industry ◽  
Organic Substrate ◽  
Fault Isolation ◽  
Preparation Methods ◽  
Chip Technology ◽  
Isolation Test ◽  
Sample Preparation Methods

Abstract The use of flip chip technology inside component packaging, so called flip chip in package (FCIP), is an increasingly common package type in the semiconductor industry because of high pin-counts, performance and reliability. Sample preparation methods and flows which enable physical failure analysis (PFA) of FCIP are thus in demand to characterize defects in die with these package types. As interconnect metallization schemes become more dense and complex, access to the backside silicon of a functional device also becomes important for fault isolation test purposes. To address these requirements, a detailed PFA flow is described which chronicles the sample preparation methods necessary to isolate a physical defect in the die of an organic-substrate FCIP.

Introduction of a Novel Sample Preparation Technique for the Failure Analysis of Silicon Integrated Photonics Modules

2019 ◽  
Author(s):  
Pradip Sairam Pichumani ◽  
Fauzia Khatkhatay
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Silicon Photonics ◽  
Cmos Technology ◽  
Single Step ◽  
Oxide Semiconductor ◽  
Disruptive Technology ◽  
Preparation Technique ◽  
Test Vehicle ◽  
Sample Preparation Technique

Abstract Silicon photonics is a disruptive technology that aims for monolithic integration of photonic devices onto the complementary metal-oxide-semiconductor (CMOS) technology platform to enable low-cost high-volume manufacturing. Since the technology is still in the research and development phase, failure analysis plays an important role in determining the root cause of failures seen in test vehicle silicon photonics modules. The fragile nature of the test vehicle modules warrants the development of new sample preparation methods to facilitate subsequent non-destructive and destructive analysis methods. This work provides an example of a single step sample preparation technique that will reduce the turnaround time while simultaneously increasing the scope of analysis techniques.

A Sample Preparation on Decapsulation Methodology for Effective Failure Analysis on Thin Small Leadless (TSLP) Flip Chip Package with Copper Pillar (CuP) Bump Interconnect Technology

2014 ◽  
Author(s):  
Gwee Hoon Yen ◽  
Ng Kiong Kay
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Flip Chip ◽  
Fault Localization ◽  
Cost Effective ◽  
Fault Isolation ◽  
Voltage Contrast ◽  
Interconnect Technology

Abstract Today, failure analysis involving flip chip [1] with copper pillar bump packaging technologies would be the major challenges faced by analysts. Most often, handling on the chips after destructive chemical decapsulation is extremely critical as there are several failure analysis steps to be continued such as chip level fault localization, chip micro probing for fault isolation, parallel lapping [2, 3, 4] and passive voltage contrast. Therefore, quality of sample preparation is critical. This paper discussed and demonstrated a quick, reliable and cost effective methodology to decapsulate the thin small leadless (TSLP) flip chip package with copper pillar (CuP) bump interconnect technology.

Backside Mechanical Preparation Methodology for Effective Failure Analysis on Small and Non-Exposed Die Paddle Package

2018 ◽  
Author(s):  
Ong Pei Hoon ◽  
Ng Kiong Kay ◽  
Gwee Hoon Yen
Keyword(s):  
Failure Analysis ◽  
Chemical Etching ◽  
Chemical Resistance ◽  
Etching Time ◽  
Lead Frame ◽  
Front Side ◽  
Electrical Measurements ◽  
Mechanical Preparation ◽  
Die Surface ◽  
Copper Lead

Abstract Chemical etching is commonly used in exposing the die surface from die front-side and die backside because of its quick etching time, burr-free and stress-free. However, this technique is risky when performing copper lead frame etching during backside preparation on small and non-exposed die paddle package. The drawback of this technique is that the copper leads will be over etched by 65% Acid Nitric Fuming even though the device’s leads are protected by chemical resistance tape. Consequently, the device is not able to proceed to any other further electrical measurements. Therefore, we introduced mechanical preparation as an alternative solution to replace the existing procedure. With the new method, we are able to ensure the copper leads are intact for the electrical measurements to improve the effectiveness and accuracy of physical failure analysis.

Solving the Voltage Contrast on Floating Substrate with Standard FA Toolset

2016 ◽  
Author(s):  
Julien Goxe ◽  
Béatrice Vanhuffel ◽  
Marie Castignolles ◽  
Thomas Zirilli
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Sample Preparation ◽  
Failure Analysis ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Silicon On Insulator ◽  
Mixed Signal ◽  
Voltage Contrast ◽  
Scanning Electron

Abstract Passive Voltage Contrast (PVC) in a Scanning Electron Microscope (SEM) or a Focused Ion Beam (FIB) is a key Failure Analysis (FA) technique to highlight a leaky gate. The introduction of Silicon On Insulator (SOI) substrate in our recent automotive analog mixed-signal technology highlighted a new challenge: the Bottom Oxide (BOX) layer, by isolating the Silicon Active Area from the bulk made PVC technique less effective in finding leaky MOSFET gates. A solution involving sample preparation performed with standard FA toolset is proposed to enhance PVC on SOI substrate.

Sample Preparation Challenges In WLCSP Epoxy Underfill Coating Removal

2012 ◽  
Author(s):  
Jason H. Lagar ◽  
Rudolf A. Sia
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Vital Role ◽  
Fault Isolation ◽  
Wafer Level ◽  
Chip Scale Package ◽  
Coating Removal ◽  
Customer Returns ◽  
Preparation Techniques ◽  
Mechanical Defect

Abstract Most Wafer Level Chip Scale Package (WLCSP) units returned by customers for failure analysis are mounted on PCB modules with an epoxy underfill coating. The biggest challenge in failure analysis is the sample preparation to remove the WLCSP device from the PCB without inducing any mechanical defect. This includes the removal of the underfill material to enable further electrical verification and fault isolation analysis. This paper discusses the evaluations conducted in establishing the WLCSP demounting process and removal of the epoxy underfill coating. Combinations of different sample preparation techniques and physical failure analysis steps were evaluated. The established process enabled the electrical verification, fault isolation and further destructive analysis of WLCSP customer returns mounted on PCB and with an epoxy underfill coating material. This paper will also showcase some actual full failure analysis of WLCSP customer returns where the established process played a vital role in finding the failure mechanism.

High-Throughput, Site-Specific Sample Prep of Ultra-Thin TEM Lamella for Process Metrology and Failure Analysis

2012 ◽  
Author(s):  
Roger Alvis ◽  
Jeff Blackwood ◽  
Sang-Hoon Lee ◽  
Matthew Bray
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Process Monitoring ◽  
High Throughput ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Memory Devices ◽  
Site Specific ◽  
Critical Dimensions ◽  
Tem Lamella

Abstract Semiconductor devices with critical dimensions less than 20nm are now being manufactured in volume. A challenge facing the failure analysis and process-monitoring community is two-fold. The first challenge of TEM sample prep of such small devices is that the basic need to end-point on a feature-of-interest pushes the imaging limit of the instrument being used to prepare the lamella. The second challenge posed by advanced devices is to prepare an artifact-free lamella from non-planar devices such as finFETs as well as from structures incorporating ‘non-traditional’ materials. These challenges are presently overcome in many advanced logic and memory devices in the focused ion beam-based TEM sample preparation processes by inverting the specimen prior to thinning to electron transparency. This paper reports a highthroughput method for the routine preparation of artifact-free TEM lamella of 20nm thickness, or less.

Impacts of Sample Preparation Methodology on TEM Failure Analysis of Advanced Semiconductor Devices

2011 ◽  
Author(s):  
Yongkai Zhou ◽  
Jie Zhu ◽  
Han Wei Teo ◽  
ACT Quah ◽  
Lei Zhu ◽  
...  
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Case Studies ◽  
Thickness Measurement ◽  
Interface Roughness ◽  
Silicide Formation ◽  
Cross Sectional ◽  
Inspection Method ◽  
Low Mass

Abstract In this paper, two failure analysis case studies are presented to demonstrate the importance of sample preparation procedures to successful failure analyses. Case study 1 establishes that Palladium (Pd) cannot be used as pre-FIB coating for SiO2 thickness measurement due to the spontaneously Pd silicide formation at the SiO2/Si interface. Platinum (Pt) is thus recommended, in spite of the Pt/SiO2 interface roughness, as the pre-FIB coating in this application. In the second case study, the dual-directional TEM inspection method is applied to characterize the profile of the “invisible” tungsten residue defect. The tungsten residue appears invisible in the planeview specimen due to the low mass-thickness contrast. It is then revealed in the cross-sectional TEM inspection.

Sign in / Sign up

Export Citation Format

Share Document