Effective and Efficient FEOL Defects Localization/Inspection by Selective Mechanical/Chemical Deprocessing

2014 ◽  
Author(s):  
Ng Hui Peng ◽  
Teo Angela ◽  
Ang Ghim Boon ◽  
Yip Kim Hong ◽  
Chang Qing Chen ◽  
...  
Keyword(s):  
Failure Analysis ◽  
High Spatial Resolution ◽  
Rapid Development ◽  
Plasma Chemistry ◽  
Fault Isolation ◽  
Physical Analysis ◽  
Process Improvements ◽  
Front End ◽  
Manufacturing Technologies ◽  
Device Miniaturization

Abstract With the rapid development of semiconductor manufacturing technologies, IC devices evolve to smaller feature sizes and higher densities, and thus the task of performing successful failure analysis (FA) is becoming increasingly difficult. Device miniaturization often requires high spatial resolution fault isolation and physical analysis [1]. To cater to the shrinking of devices, extensive process improvements have been conducted at the front-end-of-line (FEOL) structures. As a result, among the numerous types of defects leading to chip failure, FEOL defects are becoming more common for devices of advanced tech nodes [2]. Therefore, it becomes more complexity and difficulty on searching the physical defect. Sample preparation is a key activity in material and failure analysis. In order to image small structures or defects it is often necessary to remove excess material or layers hiding the feature of interest. Removing selected layers to isolate a structure is called delayering. It can be accomplished by chemical etching using liquid or plasma chemistry, or by mechanical means, by polishing off each unwanted layer.

Analog and Mixed Signal Diagnosis Flow Using Fault Isolation Techniques and Simulation

2020 ◽  
Author(s):  
Tommaso Melis ◽  
Emmanuel Simeu ◽  
Etienne Auvray
Keyword(s):  
Failure Analysis ◽  
Fault Simulation ◽  
Fault Isolation ◽  
Physical Analysis ◽  
Actual Process ◽  
Electrical Test ◽  
Simulation Tools ◽  
Isolation Techniques ◽  
Process Node ◽  
Emission Microscopy

Abstract Getting accurate fault isolation during failure analysis is mandatory for success of Physical Failure Analysis (PFA) in critical applications. Unfortunately, achieving such accuracy is becoming more and more difficult with today’s diagnosis tools and actual process node such as BCD9 and FinFET 7 nm, compromising the success of subsequent PFA done on defective SoCs. Electrical simulation is used to reproduce emission microscopy, in our previous work and, in this paper, we demonstrate the possibility of using fault simulation tools with the results of electrical test and fault isolation techniques to provide diagnosis with accurate candidates for physical analysis. The experimental results of the presented flow, from several cases of application, show the validity of this approach.

Electrical Faults Captured by In-line E-beam Inspection and Failure Analysis

2002 ◽  
Author(s):  
Z.G. Song ◽  
G.B. Ang ◽  
H.Y. Li ◽  
V. Sane ◽  
J. Indahwan ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Gate Oxide ◽  
Fault Isolation ◽  
Microelectronic Device ◽  
Final Test ◽  
Microelectronic Devices ◽  
Manufacturing Line ◽  
Front End ◽  
Electrical Faults ◽  
Metal Layers

Abstract Fault isolation is a critical step of failure analysis, which is most important for yield improvement for any new microelectronic device manufacturing. Conventionally, electrical faults are isolated by emission microscopy, liquid crystal, LIVA/TIVA and ORBIRCH etc. techniques after final test. As microelectronic devices are becoming more complicated and with multiple metal layers, failure analysis faces more challenges than before. These challenges are even tougher in wafer foundries because little device information is available. This makes yield ramp-up take longer time. Utilizing inline E-beam inspection equipment, the electrical faults can be captured at the source layer rather than after final test. E-beam inspection can be incorporated in the manufacturing line at any critical layer of front end and back-end. This paper describes the in-line E-beam inspection and presents three cases: (1) Gate-oxide issue, (2) Contact issue, and (3) Interconnect issue to demonstrate its application.

An Effective Failure Analysis Strategy for the Successful Introduction of New Products Designed in 90 and 65 nm CMOS Technologies

2004 ◽  
Author(s):  
F. Lorut ◽  
M. Lamy ◽  
M. de la Bardonnie ◽  
S. Fabre ◽  
R. Ross ◽  
...  
Keyword(s):  
Failure Analysis ◽  
New Products ◽  
Fault Isolation ◽  
Physical Characterization ◽  
Parametric Test ◽  
Process Improvements ◽  
Characterization Techniques ◽  
Analysis Strategy ◽  
Voltage Contrast

Abstract IC manufacturers, among other things, have to define a global failure analysis (FA) strategy that is best adopted to the challenges associated to the introduction of the 90 and 65 nm CMOS technologies. This article reviews the existing FA techniques and then describes an FA strategy that is aiming at fast, efficient, and economic learning in the latest 120-65 nm CMOS technologies. The strategy is based on a well-balanced mix and usage of in-line defectivity data, voltage contrast analyses, SRAM bitmap analysis results, OBIRCH fault isolation, and various advanced physical characterization techniques. A SRAM bitmap strategy has demonstrated to be very effective in driving most relevant process improvements, and also OBIRCH applied to parametric test structures has helped significantly in identifying major yield detractors.

Advantage of AFP Nanoprobing on the 28 nm Technology Failure Analysis

2013 ◽  
Author(s):  
C.Q. Chen ◽  
G.B. Ang ◽  
S.P. Zhao ◽  
Q. Alfred ◽  
N. Dayanand ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Semiconductor Manufacturing ◽  
Fault Isolation ◽  
Feature Size ◽  
Device Characterization ◽  
Advanced Technologies ◽  
Afm Imaging ◽  
Imaging Mode ◽  
Manufacturing Technologies ◽  
Level Analysis

Abstract As the rapid developments of semiconductor manufacturing technologies, the CD of the device keep shrinking. The IC devices have a smaller feature sizes and higher densities, and thus there are many challenges come up in terms of the failure analysis and localized device characterization. Besides the challenge of smaller feature size, there is another challenge as well. Some of the traditional FA method can no longer be employed on advanced technologies, such as 28nm and beyond. Quickly and successfully isolating the failed location and obtaining electrical signature of the defect has become more of a challenge, especially for the device level analysis and characterization. AFP nanoprobing system provides some solutions to advanced nodes fault isolation through its AFM imaging mode of CAFM.

Vdd Leakage Analysis by a Combination of Various Failure Analysis Techniques

2008 ◽  
Author(s):  
Z. G. Song ◽  
S. B. Ippolito ◽  
P. J. McGinnis ◽  
A. Shore ◽  
B. Paulucci ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Hot Spot ◽  
Fault Isolation ◽  
Physical Analysis ◽  
Analysis Techniques ◽  
Root Cause ◽  
Defect Location ◽  
Analysis Methodology ◽  
Analysis Process ◽  
Leakage Failure

Abstract It is generally accepted that the fault isolation of Vdd short and leakage can be globally addressed by liquid crystal analysis (LCA), photoemission analysis and/or laser stimulating techniques such as OBIRCH or TIVA. However, the hot spot detected by these techniques may be a secondary effect, rather than the exact physical defect location. Further electrical probing with knowledge of the circuit schematic and layout may still be required to pinpoint the exact physical defect location, so that a suitable physical analysis methodology can be chosen to identify the root cause of the failure. This paper has described a thorough analysis process for Vdd leakage failure by a combination of various failure analysis techniques and finally the root cause of the Vdd leakage was identified.

A New Failure Analysis Flow of Gate Oxide Integrity Failure in Wafer Fabrication

2009 ◽  
Author(s):  
Hua Younan ◽  
Chu Susan ◽  
Gui Dong ◽  
Mo Zhiqiang ◽  
Xing Zhenxiang ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Gate Dielectric ◽  
Dielectric Breakdown ◽  
Defect Density ◽  
Gate Oxide ◽  
Oxide Thickness ◽  
Fault Isolation ◽  
Wafer Fabrication ◽  
Root Cause ◽  
Gate Oxide Integrity

Abstract As device feature size continues to shrink, the reducing gate oxide thickness puts more stringent requirements on gate dielectric quality in terms of defect density and contamination concentration. As a result, analyzing gate oxide integrity and dielectric breakdown failures during wafer fabrication becomes more difficult. Using a traditional FA flow and methods some defects were observed after electrical fault isolation using emission microscopic tools such as EMMI and TIVA. Even with some success with conventional FA the root cause was unclear. In this paper, we will propose an analysis flow for GOI failures to improve FA’s success rate. In this new proposed flow both a chemical method, Wright Etch, and SIMS analysis techniques are employed to identify root cause of the GOI failures after EFA fault isolation. In general, the shape of the defect might provide information as to the root cause of the GOI failure, whether related to PID or contamination. However, Wright Etch results are inadequate to answer the questions of whether the failure is caused by contamination or not. If there is a contaminate another technique is required to determine what the contaminant is and where it comes from. If the failure is confirmed to be due to contamination, SIMS is used to further determine the contamination source at the ppm-ppb level. In this paper, a real case of GOI failure will be discussed and presented. Using the new failure analysis flow, the root cause was identified to be iron contamination introduced from a worn out part made of stainless steel.

The Electrical Characterization and Physical Failure Analysis for Transistor Gate Leakage

2006 ◽  
Author(s):  
Tsung-Te Li ◽  
Chao-Chi Wu ◽  
Jung-Hsiang Chuang ◽  
Jon C. Lee
Keyword(s):  
Failure Analysis ◽  
Electrical Characterization ◽  
Physical Analysis ◽  
Gate Leakage ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron ◽  
Voltage Stress ◽  
Leakage Site

Abstract This article describes the electrical and physical analysis of gate leakage in nanometer transistors using conducting atomic force microscopy (C-AFM), nano-probing, transmission electron microscopy (TEM), and chemical decoration on simulated overstressed devices. A failure analysis case study involving a soft single bit failure is detailed. Following the nano-probing analysis, TEM cross sectioning of this failing device was performed. A voltage bias was applied to exaggerate the gate leakage site. Following this deliberate voltage overstress, a solution of boiling 10%wt KOH was used to etch decorate the gate leakage site followed by SEM inspection. Different transistor leakage behaviors can be identified with nano-probing measurements and then compared with simulation data for increased confidence in the failure analysis result. Nano-probing can be used to apply voltage stress on a transistor or a leakage path to worsen the weak point and then observe the leakage site easier.

Application of Scan Based FA and Advanced Passive Voltage Contrast Technique in Defect Isolation

2003 ◽  
Author(s):  
Michael B. Schmidt ◽  
Noor Jehan Saujauddin
Keyword(s):  
Failure Analysis ◽  
Large Scale ◽  
Fault Isolation ◽  
Electronic Information ◽  
Scan Testing ◽  
Challenging Environment ◽  
Contrast Technique ◽  
Defect Isolation ◽  
Voltage Contrast ◽  
Higher Sensitivity

Abstract Scan testing and passive voltage contrast (PVC) techniques have been widely used as failure analysis fault isolation tools. Scan diagnosis can narrow a failure to a given net and passive voltage contrast can give real-time, large-scale electronic information about a sample at various stages of deprocessing. In the highly competitive and challenging environment of today, failure analysis cycle time is very important. By combining scan FA with a much higher sensitivity passive voltage contrast technique, one can quickly find defects that have traditionally posed a great challenge.

Thin-Die Flip Chip Physical-FA Process Flow

2002 ◽  
Author(s):  
Andrew J. Komrowski ◽  
N. S. Somcio ◽  
Daniel J. D. Sullivan ◽  
Charles R. Silvis ◽  
Luis Curiel ◽  
...  
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Flip Chip ◽  
Semiconductor Industry ◽  
Organic Substrate ◽  
Fault Isolation ◽  
Preparation Methods ◽  
Chip Technology ◽  
Isolation Test ◽  
Sample Preparation Methods

Abstract The use of flip chip technology inside component packaging, so called flip chip in package (FCIP), is an increasingly common package type in the semiconductor industry because of high pin-counts, performance and reliability. Sample preparation methods and flows which enable physical failure analysis (PFA) of FCIP are thus in demand to characterize defects in die with these package types. As interconnect metallization schemes become more dense and complex, access to the backside silicon of a functional device also becomes important for fault isolation test purposes. To address these requirements, a detailed PFA flow is described which chronicles the sample preparation methods necessary to isolate a physical defect in the die of an organic-substrate FCIP.

Application of AFP Nanoprobing Light-Induced Photovoltaic Current in the Failure Analysis

2017 ◽  
Author(s):  
C.Q. Chen ◽  
P.T. Ng ◽  
G.B. Ang ◽  
Francis Rivai ◽  
S.L. Ting ◽  
...  
Keyword(s):  
Image Analysis ◽  
Failure Analysis ◽  
Photovoltaic Effect ◽  
Electrical Characterization ◽  
Fault Isolation ◽  
Device Performance ◽  
Semiconductor Technology ◽  
Current Image ◽  
Scaling Down ◽  
Detailed Circuit

Abstract As semiconductor technology keeps scaling down, failure analysis and device characterizations become more and more challenging. Global fault isolation without detailed circuit information comprises the majority of foundry EFA cases. Certain suspected areas can be isolated, but further narrow-down of transistor and device performance is very important with regards to process monitoring and failure analysis. A nanoprobing methodology is widely applied in advanced failure analysis, especially during device level electrical characterization. It is useful to verify device performance and to prove the problematic structure electrically. But sometimes the EFA spot coverage is too big to do nanoprobing analysis. Then further narrow-down is quite critical to identify the suspected structure before nanoprobing is employed. That means there is a gap between global fault isolation and localized device analysis. Under these kinds of situation, PVC and AFP current image are offen options to identify the suspected structure, but they still have their limitation for many soft defect or marginal fails. As in this case, PVC and AFP current image failed to identify the defect in the spot range. To overcome the shortage of PVC and AFP current image analysis, laser was innovatively applied in our current image analysis in this paper. As is known to all, proper wavelength laser can induce the photovoltaic effect in the device. The photovoltaic effect induced photo current can bring with it some information of the device. If this kind of information was properly interpreted, it can give us some clue of the device performance.

Sign in / Sign up

Export Citation Format

Share Document