scholarly journals Inner Spacer Engineering to Improve Mechanical Stability in Channel-Release Process of Nanosheet FETs

Electronics ◽  
2021 ◽  
Vol 10 (12) ◽  
pp. 1395
Author(s):  
Khwang-Sun Lee ◽  
Jun-Young Park
Keyword(s):  
Elastic Property ◽  
Contact Area ◽  
Mechanical Stability ◽  
Dielectric Material ◽  
Mechanical Instability ◽  
Release Process ◽  
Rigid Spacer ◽  
Wide Contact ◽  
Simulation Results ◽  
The Impact

Mechanical stress is demonstrated in the fabrication process of nanosheet FETs. In particular, unwanted mechanical instability stemming from gravity during channel-release is covered in detail by aid of 3-D simulations. The simulation results show the physical weakness of suspended nanosheets and the impact of nanosheet thickness. Inner spacer engineering based on geometry and elastic property are suggested for better mechanical stability. The formation of wide contact area between inner spacer and nanosheet, as well as applying rigid spacer dielectric material, are preferred.

scholarly journals Mechanical Stability of Hybrid Corrugated Sandwich Plates under Fluid-Structure-Thermal Coupling for Novel Thermal Protection Systems

2020 ◽  
Vol 10 (8) ◽  
pp. 2790
Author(s):  
Wenzheng Zhuang ◽  
Chao Yang ◽  
Zhigang Wu
Keyword(s):  
Mechanical Stability ◽  
Thermal Protection ◽  
Element Model ◽  
Parameter Study ◽  
The Novel ◽  
Thermal Coupling ◽  
Mechanical Instability ◽  
Fluid Structure ◽  
Thermal Protection Systems ◽  
Protection Systems

Hybrid corrugated sandwich (HCS) plates have become a promising candidate for novel thermal protection systems (TPS) due to their multi-functionality of load bearing and thermal protection. For hypersonic vehicles, the novel TPS that performs some structural functions is a potential method of saving weight, which is significant in reducing expensive design/manufacture cost. Considering the novel TPS exposed to severe thermal and aerodynamic environments, the mechanical stability of the HCS plates under fluid-structure-thermal coupling is crucial for preliminary design of the TPS. In this paper, an innovative layerwise finite element model of the HCS plates is presented, and coupled fluid-structure-thermal analysis is performed with a parameter study. The proposed method is validated to be accurate and efficient against commercial software simulation. Results have shown that the mechanical instability of the HCS plates can be induced by fluid-structure coupling and further accelerated by thermal effect. The influences of geometric parameters on thermal buckling and dynamic stability present opposite tendencies, indicating a tradeoff is required for the TPS design. The present analytical model and numerical results provide design guidance in the practical application of the novel TPS.

scholarly journals Measuring Hydrometeors Using a Precipitation Microphysical Characteristics Sensor: Sampling Effect of Different Bin Sizes on Drop Size Distribution Parameters

2018 ◽  
Vol 2018 ◽  
pp. 1-15 ◽  
Author(s):  
Xichuan Liu ◽  
Taichang Gao ◽  
Yuntao Hu ◽  
Xiaojian Shu
Keyword(s):  
Drop Size ◽  
Rain Rate ◽  
Monte Carlo Model ◽  
Rain Gauge ◽  
Sampling Schemes ◽  
Distribution Parameters ◽  
Optimum Sampling ◽  
Simulation Results ◽  
The Impact ◽  
Good Agreement

In order to improve the measurement of precipitation microphysical characteristics sensor (PMCS), the sampling process of raindrops by PMCS based on a particle-by-particle Monte-Carlo model was simulated to discuss the effect of different bin sizes on DSD measurement, and the optimum sampling bin sizes for PMCS were proposed based on the simulation results. The simulation results of five sampling schemes of bin sizes in four rain-rate categories show that the raw capture DSD has a significant fluctuation variation influenced by the capture probability, whereas the appropriate sampling bin size and width can reduce the impact of variation of raindrop number on DSD shape. A field measurement of a PMCS, an OTT PARSIVEL disdrometer, and a tipping bucket rain Gauge shows that the rain-rate and rainfall accumulations have good consistencies between PMCS, OTT, and Gauge; the DSD obtained by PMCS and OTT has a good agreement; the probability of N0, μ, and Λ shows that there is a good agreement between the Gamma parameters of PMCS and OTT; the fitted μ-Λ and Z-R relationship measured by PMCS is close to that measured by OTT, which validates the performance of PMCS on rain-rate, rainfall accumulation, and DSD related parameters.

scholarly journals Mechanical Behavior of Hydroxyapatite-Chitosan Composite: Effect of Processing Parameters

Minerals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 213
Author(s):  
Hamid Ait Said ◽  
Hassan Noukrati ◽  
Hicham Ben Youcef ◽  
Ayoub Bayoussef ◽  
Hassane Oudadesse ◽  
...  
Keyword(s):  
Molecular Weight ◽  
Compressive Strength ◽  
Mechanical Strength ◽  
Bone Repair ◽  
Mechanical Stability ◽  
Three Dimensional ◽  
Processing Parameters ◽  
Composite Effect ◽  
Solid Liquid ◽  
The Impact

Three-dimensional hydroxyapatite-chitosan (HA-CS) composites were formulated via solid-liquid technic and freeze-drying. The prepared composites had an apatitic nature, which was demonstrated by X-ray diffraction and Infrared spectroscopy analyses. The impact of the solid/liquid (S/L) ratio and the content and the molecular weight of the polymer on the composite mechanical strength was investigated. An increase in the S/L ratio from 0.5 to 1 resulted in an increase in the compressive strength for HA-CSL (CS low molecular weight: CSL) from 0.08 ± 0.02 to 1.95 ± 0.39 MPa and from 0.3 ± 0.06 to 2.40 ± 0.51 MPa for the HA-CSM (CS medium molecular weight: CSM). Moreover, the increase in the amount (1 to 5 wt%) and the molecular weight of the polymer increased the mechanical strength of the composite. The highest compressive strength value (up to 2.40 ± 0.51 MPa) was obtained for HA-CSM (5 wt% of CS) formulated at an S/L of 1. The dissolution tests of the HA-CS composites confirmed their cohesion and mechanical stability in an aqueous solution. Both polymer and apatite are assumed to work together, giving the synergism needed to make effective cylindrical composites, and could serve as a promising candidate for bone repair in the orthopedic field.

scholarly journals A New Method to Determine the Impact of Individual Field Quantities on Cycle-to-Cycle Variations in a Spark-Ignited Gas Engine

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4136
Author(s):  
Clemens Gößnitzer ◽  
Shawn Givler
Keyword(s):  
Kinetic Energy ◽  
Flow Field ◽  
Turbulent Kinetic Energy ◽  
Negative Impact ◽  
Operating Conditions ◽  
Engine Operation ◽  
Gas Engine ◽  
Cycle Simulation ◽  
Simulation Results ◽  
The Impact

Cycle-to-cycle variations (CCV) in spark-ignited (SI) engines impose performance limitations and in the extreme limit can lead to very strong, potentially damaging cycles. Thus, CCV force sub-optimal engine operating conditions. A deeper understanding of CCV is key to enabling control strategies, improving engine design and reducing the negative impact of CCV on engine operation. This paper presents a new simulation strategy which allows investigation of the impact of individual physical quantities (e.g., flow field or turbulence quantities) on CCV separately. As a first step, multi-cycle unsteady Reynolds-averaged Navier–Stokes (uRANS) computational fluid dynamics (CFD) simulations of a spark-ignited natural gas engine are performed. For each cycle, simulation results just prior to each spark timing are taken. Next, simulation results from different cycles are combined: one quantity, e.g., the flow field, is extracted from a snapshot of one given cycle, and all other quantities are taken from a snapshot from a different cycle. Such a combination yields a new snapshot. With the combined snapshot, the simulation is continued until the end of combustion. The results obtained with combined snapshots show that the velocity field seems to have the highest impact on CCV. Turbulence intensity, quantified by the turbulent kinetic energy and turbulent kinetic energy dissipation rate, has a similar value for all snapshots. Thus, their impact on CCV is small compared to the flow field. This novel methodology is very flexible and allows investigation of the sources of CCV which have been difficult to investigate in the past.

Recent advanced applications of ion-gel in ionic-gated transistor

2021 ◽  
Vol 5 (1) ◽  
Author(s):  
Depeng Wang ◽  
Shufang Zhao ◽  
Ruiyang Yin ◽  
Linlin Li ◽  
Zheng Lou ◽  
...  
Keyword(s):  
Recent Progress ◽  
Mechanical Stability ◽  
Dielectric Material ◽  
Charge Carriers ◽  
Future Perspectives ◽  
Organic Transistor ◽  
Ion Gel ◽  
Physical And Chemical ◽  
Large Capacitance ◽  
Advanced Applications

AbstractDiversified regulation of electrons have received much attention to realize a multi-functional transistor, and it is crucial to have a considerable control over the charge carriers in transistors. Ionic gel, as the dielectric material in transistors, facilitates a large capacitance, and high induced-carrier concentrations. This review presents the recent progress in ionic-gated transistors (IGTs) that have good mechanical stability as well as high physical and chemical stability. We first briefly introduce the various applications of IGTs in sensors, neuromorphic transistors, organic transistor circuits, and health detection. Finally, the future perspectives of IGTs are discussed and some possible solutions to the challenges are also proposed.

A Dicode Signaling Scheme for Capacitively Coupled Interface

2011 ◽  
Vol 497 ◽  
pp. 296-305
Author(s):  
Yasushi Yuminaka ◽  
Kyohei Kawano
Keyword(s):  
Partial Response ◽  
Data Transmission ◽  
High Speed ◽  
Circuit Simulation ◽  
Frequency Bandwidth ◽  
Capacitively Coupled ◽  
Limited Frequency ◽  
Simulation Results ◽  
Response Coding ◽  
The Impact

In this paper, we present a bandwidth-efficient partial-response signaling scheme for capacitivelycoupled chip-to-chip data transmission to increase data rate. Partial-response coding is knownas a technique that allows high-speed transmission while using a limited frequency bandwidth, by allowingcontrolled intersymbol interference (ISI). Analysis and circuit simulation results are presentedto show the impact of duobinary (1+D) and dicode (1-D) partial-response signaling for capacitivelycoupled interface.

An Improved Initial Alignment Method of Strap-Down Inertial Navigation System on a Swaying Base

2013 ◽  
Vol 415 ◽  
pp. 143-148
Author(s):  
Li Hua Zhu ◽  
Xiang Hong Cheng
Keyword(s):  
Navigation System ◽  
Inertial Navigation System ◽  
Alignment Algorithm ◽  
Alignment Method ◽  
Initial Alignment ◽  
Vehicle Simulation ◽  
Robust Property ◽  
Simulation Results ◽  
Lever Arm Effect ◽  
The Impact

The design of an improved alignment method of SINS on a swaying base is presented in this paper. FIR filter is taken to decrease the impact caused by the lever arm effect. And the system also encompasses the online estimation of gyroscopes’ drift with Kalman filter in order to do the compensation, and the inertial freezing alignment algorithm which helps to resolve the attitude matrix with respect to its fast and robust property to provide the mathematical platform for the vehicle. Simulation results show that the proposed method is efficient for the initial alignment of the swaying base navigation system.

Bone ingrowth in total knee arthroplasty: The impact of HA-coatings and the relation with mechanical stability

1998 ◽  
Vol 31 ◽  
pp. 26
Author(s):  
L. Labey ◽  
H. Van Campenhout ◽  
J. Vander Sloten ◽  
R. Van Audekercke ◽  
G. Van der Perre ◽  
...  
Keyword(s):  
Total Knee Arthroplasty ◽  
Knee Arthroplasty ◽  
Mechanical Stability ◽  
Bone Ingrowth ◽  
Total Knee ◽  
The Impact

Investigation on penetration model of shaped charge jet in water

2016 ◽  
Vol 30 (02) ◽  
pp. 1550268 ◽  
Author(s):  
Jinwei Shi ◽  
Xingbai Luo ◽  
Jinming Li ◽  
Jianwei Jiang
Keyword(s):  
Numerical Simulation ◽  
Theoretical Model ◽  
Model Simulation ◽  
Theoretical Models ◽  
Theoretical Research ◽  
Water Medium ◽  
Simulation Results ◽  
Jet Penetration ◽  
The Impact ◽  
Penetration Velocity

To analyze the process of jet penetration in water medium quantitatively, the properties of jet penetration spaced target with water interlayer were studied through test and numerical simulation. Two theoretical models of jet penetration in water were proposed. The theoretical model 1 was established considering the impact of the shock wave, combined with the shock equation Rankine–Hugoniot and the virtual origin calculation method. The theoretical model 2 was obtained by fitting theoretical analysis and numerical simulation results. The effectiveness and universality of the two theoretical models were compared through the numerical simulation results. Both the models can reflect the relationship between the penetration velocity and the penetration distance in water well, and both the deviation and stability of theoretical model 1 are better than 2, the lower penetration velocity, and the larger deviation of the theoretical model 2. Therefore, the theoretical model 1 can reflect the properties of jet penetration in water effectively, and provide the reference of model simulation and theoretical research.

The Impact Analysis of Revolute Pair Clearance to the End Pose Accuracy of Welding Robot

2015 ◽  
Vol 778 ◽  
pp. 259-263
Author(s):  
Fa Jun Zhang ◽  
Lin Zi Li ◽  
Hui Lin ◽  
Yin Lin Pu ◽  
Zhu Xin
Keyword(s):  
Mathematical Model ◽  
Impact Analysis ◽  
Joint Clearance ◽  
Welding Robot ◽  
Movement Characteristic ◽  
Movement Stability ◽  
Simulation Results ◽  
The Impact ◽  
The Mathematical Model ◽  
Welding Position

Various uncertain factors affect the movement of the welding robot, thus welding gun tend to deviate from the theory of welding position which reduces the welding accuracy, of which the revolute pair clearance have an greater effect on the movement of the welding robot. In order to study the influence of revolute pair clearance to the end pose accuracy of welding robot, the mathematical model of revolute pair clearance was established, and the software SolidWorks was used for establishing the welding robot model, making simulations of the mechanical arm with joint clearance and no joint clearance. At last, the movement characteristic of the hinge shaft is attained. The simulation results showed that the shaft velocity and displacement of mechanical arm with joint clearance has a certain degree of fluctuation, which affecting the end pose accuracy of welding robot , and reducing the movement stability and the welding accuracy of welding robot.

Sign in / Sign up

Export Citation Format

Share Document