scholarly journals Fabrication of High-Performance Bamboo–Plastic Composites Reinforced by Natural Halloysite Nanotubes

Molecules ◽  
2020 ◽  
Vol 25 (9) ◽  
pp. 2259
Author(s):  
Xiaobei Jin ◽  
Jingpeng Li ◽  
Rong Zhang ◽  
Zehui Jiang ◽  
Daochun Qin
Keyword(s):  
Thermal Stability ◽  
High Performance ◽  
Moisture Absorption ◽  
Mechanical Performance ◽  
Halloysite Nanotubes ◽  
Industrial Applications ◽  
High Concentration ◽  
Morphological Studies ◽  
Plastic Composites ◽  
The Impact

Bamboo-plastic composites (BPCs) as new biomass-plastic composites have recently attracted much attention. However, weak mechanical performance and high moisture absorption as well as low thermal stability greatly limit their industrial applications. In this context, different amounts of halloysite nanotubes (HNTs) were used as a natural reinforcing filler for BPCs. It was found that the thermal stability of BPCs increased with increasing HNT contents. The mechanical strength of BPCs was improved with the increase in HNT loading up to 4 wt% and then worsened, while the impact strengths were slightly reduced. Low HNT content (below 4 wt%) also improved the dynamic thermomechanical properties and reduced the water absorption of the BPCs. Morphological studies confirmed the improved interfacial compatibility of the BPC matrix with 4 wt% HNT loading, and high-concentration HNT loading (above 6 wt%) resulted in easy agglomeration. The results highlight that HNTs could be a feasible candidate as nanoreinforcements for the development of high-performance BPCs.

scholarly journals Smoothing additive manufactured parts using ns-pulsed laser radiation

2021 ◽  
Author(s):  
Florian Kuisat ◽  
Fernando Lasagni ◽  
Andrés Fabián Lasagni
Keyword(s):  
Surface Roughness ◽  
Mechanical Performance ◽  
State Of The Art ◽  
Pulsed Laser ◽  
Industrial Applications ◽  
Laser Source ◽  
Pulsed Laser Radiation ◽  
Current State ◽  
The Impact

AbstractIt is well known that the surface topography of a part can affect its mechanical performance, which is typical in additive manufacturing. In this context, we report about the surface modification of additive manufactured components made of Titanium 64 (Ti64) and Scalmalloy®, using a pulsed laser, with the aim of reducing their surface roughness. In our experiments, a nanosecond-pulsed infrared laser source with variable pulse durations between 8 and 200 ns was applied. The impact of varying a large number of parameters on the surface quality of the smoothed areas was investigated. The results demonstrated a reduction of surface roughness Sa by more than 80% for Titanium 64 and by 65% for Scalmalloy® samples. This allows to extend the applicability of additive manufactured components beyond the current state of the art and break new ground for the application in various industrial applications such as in aerospace.

Indole-based high-performance polymeric materials with enhanced mechanical and thermal properties via cation-π interaction

2019 ◽  
Vol 32 (6) ◽  
pp. 662-668
Author(s):  
Xiao-fang Guan ◽  
Cong Liao ◽  
Li Yang ◽  
Guan-jun Chang
Keyword(s):  
Thermal Stability ◽  
Heat Resistance ◽  
Self Assembly ◽  
High Performance ◽  
Mechanical Performance ◽  
Polymeric Materials ◽  
Design Strategy ◽  
Mechanical And Thermal Properties ◽  
Innovative Design ◽  
High Performance Polymers

The preparation of high-performance polymeric materials with both excellent overall mechanical properties and heat resistance remains a considerable challenge. Inspired by the delicate self-assembly processes in nature, a facile strategy is reported for the preparation of high-performance polymeric materials with enhanced mechanical strength and improved thermal stability. In this instance, we successfully constructed a cation- π cross-linked polyimide (Na-poly(aryl indole) imide (Na-PINI)) film with enhanced mechanical performance and heat resistance (∼490°C). This work presents an innovative design strategy for realizing robust polymeric materials with integrated strength and thermal stability; the cation- π interaction is demonstrated to be a new method that may achieve many useful properties for high-performance polymers.

Vinyl-terminated butadiene acrylonitrile improves the toughness, processing window, and thermal stability of bismaleimide resin

2016 ◽  
Vol 29 (10) ◽  
pp. 1199-1208 ◽  
Author(s):  
Dezhi Wang ◽  
Xin Wang ◽  
Lizhu Liu ◽  
Chunyan Qu ◽  
Changwei Liu ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Mechanical Performance ◽  
Resin System ◽  
Excellent Performance ◽  
Bismaleimide Resin ◽  
Processing Window ◽  
Low Viscosity ◽  
Isothermal Test ◽  
The Impact ◽  
Thermal Stability Of

Structural materials with excellent toughness, a wide processing window, outstanding mechanical performance, and high thermal stability are highly desired in engineering. This work reports a novel bismaleimide (BMI) resin system fabricated using bis[4-(4-maleimidephen-oxy)phenyl)]propane (BMPP), 1-(2-methyl-5-(2,5-dioxo-2H-pyrrol-1(5 H)-yl) phenyl)-1H-pyrrole-2,5-dione (BTM), and diallyl bisphenol A (DABPA) by a melt method. The behaviors of the BTM/BMPP/DABPA resin were modified by adding vinyl-terminated butadiene acrylonitrile (VTBN) in various amounts. The cured BTM/BMPP/DABPA/VTBN resin system exhibited all of the abovementioned desirable properties. Excellent performance was achieved by the post-cured BMI resin containing 6 phr of VTBN (VTBN-6). The glass transition temperature ( Tg) and the 5% weight loss temperature of VTBN-6 were 278°C and 408°C, respectively. Relative to VTBN-0 (BMI resin without VTBN), the impact strength of cured VTBN-6 (12.32 KJ/m2) improved by 45.6%, and the fracture toughness values, KIC and GIC, increased by 48.7% and 26%, respectively. Moreover, the prepolymer of VTBN-6 exhibited low viscosity over a wide temperature range (70–200°C) under dynamic conditions and for an extended time (70 min; 75% improvement over VTBN-0) in an isothermal test. These results confirm the wide processing window of VTBN-6. The high toughness of the VTBN-containing BMI resin was compatible with other excellent performances of the modified resin.

scholarly journals Synchronously Strengthen and Toughen Polypropylene Using Tartaric Acid-Modified Nano-CaCO3

Nanomaterials ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 2493
Author(s):  
Junlong Yao ◽  
Hanchao Hu ◽  
Zhengguang Sun ◽  
Yucong Wang ◽  
Huabo Huang ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Impact Toughness ◽  
Tartaric Acid ◽  
High Performance ◽  
Mechanical Performance ◽  
Low Cost ◽  
Complexing Agent ◽  
Environmental Technology ◽  
The Impact ◽  
First Time

In order to overcome the challenge of synchronously strengthening and toughening polypropylene (PP) with a low-cost and environmental technology, CaCO3 (CC) nanoparticles are modified by tartaric acid (TA), a kind of food-grade complexing agent, and used as nanofillers for the first time. The evaluation of mechanical performance showed that, with 20 wt.% TA-modified CC (TAMCC), the impact toughness and tensile strength of TAMCC/PP were 120% and 14% more than those of neat PP, respectively. Even with 50 wt.% TAMCC, the impact toughness and tensile strength of TAMCC/PP were still superior to those of neat PP, which is attributable to the improved compatibility and dispersion of TAMCC in a PP matrix, and the better fluidity of TAMCC/PP nanocomposite. The strengthening and toughening mechanism of TAMCC for PP involves interfacial debonding between nanofillers and PP, and the decreased crystallinity of PP, but without the formation of β-PP. This article presents a new applicable method to modify CC inorganic fillers with a green modifier and promote their dispersion in PP. The obtained PP nanocomposite simultaneously achieved enhanced mechanical strength and impact toughness even with high content of nanofillers, highlighting bright perspective in high-performance, economical, and eco-friendly polymer-inorganic nanocomposites.

Studies of the Physical Properties of Cycloaliphatic Epoxy Resin Reacted with Anhydride Curing Agents

2017 ◽  
Vol 737 ◽  
pp. 248-255 ◽  
Author(s):  
Tae Hee Kim ◽  
Dae Yeon Kim ◽  
Choong Sun Lim ◽  
Bong Kuk Seo
Keyword(s):  
Physical Properties ◽  
Reaction Kinetics ◽  
Epoxy Resin ◽  
High Performance ◽  
Industrial Applications ◽  
Scanning Calorimetry ◽  
Low Viscosity ◽  
High Performance Polymer ◽  
Curing Agents ◽  
The Impact

The preparation of high performance epoxy composites for industrial applications has been extensively researched. In this report, we study the change in physical properties and reaction kinetics between epoxy resin and curing agents of similar geometry. For the experiments, celloxide 2021P, an epoxy resin having low viscosity, was blended with three different curing agents: methylhexahydropthalic acid, methyltetrahydropthalic acid, and 5-norbornene-2, 3-dicarboxylic anhydride. The amount of 1, 2-dimethylimidazole catalyst was controlled, and the highest heat flow temperature (Tpeak) was observed at around 145 °C. The impact on reaction kinetics relative to the change in heating rate was studied with differential scanning calorimetry (DSC) for each of the curing agents. The glass transition temperature (Tg) of each composition was measured with a second DSC cycle. The prepared epoxy compositions were thermally cured in a metallic mold to provide pure epoxy resins without fillers. Finally, the flexural strengths of these resins were compared to each other. The authors believe that insights into choosing an appropriate epoxy binder are useful when it comes to the overall preparation of high performance polymer composites.

TOUGHMET 2

Alloy Digest ◽  
2013 ◽  
Vol 62 (5) ◽  
Keyword(s):  
Heat Treatment ◽  
Thermal Stability ◽  
Fracture Toughness ◽  
Wear Resistance ◽  
High Performance ◽  
Mechanical Performance ◽  
High Thermal Stability ◽  
Lead Free ◽  
Plain Bearing ◽  
Ni Alloy

Abstract ToughMet 2 is a high performance, wrought, heat treatable, lead-free strip Cu-Ni alloy that imparts superior mechanical performance and high thermal stability to plain bearing applications. Parts are easily formed and they can be machined either before or after heat treatment. ToughMet alloys are a line of spinodal hardened Cu-Ni anti-galling alloys for bearings capable of performing with a variety of shafting materials and lubricants. The alloys combine a high lubricity with wear resistance in these severe loading conditions. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness and fatigue. It also includes information on corrosion resistance as well as forming and machining. Filing Code: Cu-724. Producer or source: Materion Brush Performance Alloys. Originally published September 2004, revised May 2013.

The Impact of Interface Characteristics on Mechanical Performance of a Hot-Forged Cu/Ti-Coated-Diamond Composite

2021 ◽  
Vol 1016 ◽  
pp. 1682-1689
Author(s):  
Lei Lei ◽  
Leandro Bolzoni ◽  
Fei Yang
Keyword(s):  
High Performance ◽  
Mechanical Performance ◽  
Hot Forging ◽  
Copper Matrix ◽  
Diamond Surface ◽  
Copper Powders ◽  
Tic Particle ◽  
Elemental Copper ◽  
Cold Pressed ◽  
The Impact

The Cu/55vol.%diamond (Ti) composites were fabricated by hot forging of the cold-pressed powder preforms, consisted of elemental copper powders and Ti-coated diamond particles, at 800 °C (800C-Cu/55Dia composite) and 1050 °C (1050C-Cu55Dia composite), respectively. Well bonded interface was achieved between the diamond and the copper matrix for the 800C-Cu/55Dia composite, and the coverage of diamond by interface was about 96%, attributed to homogeneously distributed nanospherical TiC interface formed on the diamond surface. However, obvious coarse TiC particle size and spallation of the formed interface were observed in the 1050C-Cu55Dia composite, implying that the composite had a relatively low bonding strength. The formed chemical bonding, good wettability and strong mechanical interlocking between the diamond and the copper matrix enable the 800C-Cu/55Dia composite having a high tensile strength of 145 MPa and a strain at fracture of 0.35%, which are about 260% and 170% higher than those of the 1050C-Cu55Dia composite, suggesting that the 800C-Cu/55Dia composite has the potential to have a high thermal conductivity and use as high-performance heat sink materials.

On the Mechanical Reliability of Photo-BCB-Based Thin Film Dielectric Polymer for Electronic Packaging Applications

1999 ◽  
Vol 122 (1) ◽  
pp. 28-33 ◽  
Author(s):  
Jang-hi Im ◽  
Edward O. Shaffer ◽  
Theodore Stokich, ◽  
Andrew Strandjord ◽  
Jack Hetzner ◽  
...  
Keyword(s):  
Thin Film ◽  
Thermal Stability ◽  
Photoelectron Spectroscopy ◽  
Moisture Absorption ◽  
Mechanical Performance ◽  
Adhesion Promoter ◽  
Helium Atmosphere ◽  
Thermally Induced ◽  
Good Thermal Stability ◽  
Substrate Surfaces

This work examines the mechanical performance of thin film coatings from Photosensitive-benzocyclobutene (Photo-BCB) formulations (Cyclotene2 4024, 4026 and 7200), on various substrate surfaces such as Al, Cu, Si, and SiN. The adhesion promoter used was designated AP-3000 and was based on vinyltriacetoxysilane (VTAS), which had been properly hydrolyzed and advanced. Measurement of the interfacial adhesion was performed primarily using the modified Edge Liftoff Test m-ELT. It was found that, by applying the newly developed adhesion promoter, AP-3000, the interfacial energy of Photo-BCB to Al, Cu, Si, and SiN was significantly improved, often approaching the toughness of Photo-BCB, ca. 45 J/m2. The x-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) analyses of the delaminated surfaces of the Photo-BCB/Al structure revealed distinct differences in surface roughness and the chemical composition depending on whether or not adhesion promoter was used. Other parameters important for long term stability (e.g., moisture uptake and thermal stability) of Photo-BCB were also measured. The equilibrium moisture content at 84 percent RH in ambient temperature was low, 0.14 wt percent and the thermally induced weight loss at 330°C in helium atmosphere was less than 1 percent/h. The low moisture absorption and good thermal stability, together with the given mechanical toughness and adhesion, allow the Photo-BCB to be widely usable for various microelectronic packaging applications, for up to 40 μm thick build in the case of silicon substrate. [S1043-7398(00)00701-5]

Effects of Halloysite Nanotubes on Mechanical and Thermal Stability of Poly(Ethylene Terephthalate)/Polycarbonate Nanocomposites

2015 ◽  
Vol 735 ◽  
pp. 8-12
Author(s):  
Nurul Ain Jamaludin ◽  
Azman Hassan ◽  
Norhayani Othman ◽  
Mohammad Jawaid
Keyword(s):  
Thermal Stability ◽  
Ethylene Terephthalate ◽  
Flexural Modulus ◽  
Halloysite Nanotubes ◽  
Mechanical And Thermal Properties ◽  
Poly Ethylene Terephthalate ◽  
Twin Screw ◽  
Poly Ethylene ◽  
The Impact ◽  
Thermal Stability Of

The objective of this study is to investigate the effect of halloysite nanotubes (HNTs) loading on mechanical and thermal properties of poly(ethylene terephthalate)/polycarbonate (PET/PC) nanocomposites. Nanocomposites containing 70PET/30PC and 2-8 phr HNTs were prepared by twin screw extruder followed by injection moulding. As the percentage of HNTs increased, the flexural modulus increased. However, the flexural strength decreased with increasing HNTs content. The impact strength also decreased when HNTs increased. Thermogravimetry analysis of PET/PC/HNTs nanocomposites showed higher thermal stability at high HNTs content. However, on further addition of HNTs up to 8 phr, thermal stability of the nanocomposites decreased due to the poor dispersion of HNTs.

scholarly journals Preparation and Characterization of Nanocomposite Films Containing Nano-Aluminum Nitride and Cellulose Nanofibrils

Nanomaterials ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 1121 ◽  
Author(s):  
Shuangxi Nie ◽  
Yuehua Zhang ◽  
Linmao Wang ◽  
Qin Wu ◽  
Shuangfei Wang
Keyword(s):  
Thermal Stability ◽  
Aluminum Nitride ◽  
High Performance ◽  
Mechanical Performance ◽  
Cellulose Nanofibrils ◽  
Crystal Form ◽  
Mechanical Tests ◽  
Substrate Material ◽  
Nanocomposite Films ◽  
Sodium Chlorite

Nanocomposites consisting of cellulose nanofibrils (CNFs) and nano-aluminum nitride (AlN) were prepared using a simple vacuum-assisted filtration process. Bleached sugarcane bagasse pulp was treated with potassium hydroxide and sodium chlorite, and was subsequently ultra-finely ground and homogenized to obtain CNFs. Film nanocomposites were prepared by mixing CNFs with various AlN amounts (0–20 wt.%). X-ray diffraction revealed that the crystal form of CNF-AlN nanocomposites was different to those of pure CNFs and AlN. The mechanical performance and thermal stability of the CNF-AlN nanocomposites were evaluated through mechanical tests and thermogravimetric analysis, respectively. The results showed that the CNF-AlN nanocomposites exhibited excellent mechanical and thermal stability, and represented a green renewable substrate material. This type of nanocomposite could present great potential for replacing traditional polymer substrates, and could provide creative opportunities for designing and fabricating high-performance portable electronics in the near future.

Sign in / Sign up

Export Citation Format

Share Document