scholarly journals SYNTHESIS, CHARACTERIZATION AND ADSORPTION STUDIES OF PHOSPHORYLATED CELLULOSE FOR THE RECOVERY OF LITHIUM FROM AQUEOUS SOLUTIONS

2021 ◽  
Vol 55 (3-4) ◽  
pp. 385-401
Author(s):  
YASAR KEMAL RECEPOGLU ◽  
ASLI YÜKSEL
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Maximum Adsorption Capacity ◽  
Uptake Capacity ◽  
Adsorption Models ◽  
Phosphorylation Reaction ◽  
Equilibrium Data ◽  
Characterization Studies ◽  
Fast Kinetic ◽  
Mild Temperature

"In this study, pristine cellulose was functionalized by the phosphorylation reaction to make it suitable for lithium separation. After characterization studies of the synthesized adsorbent with SEM, EDX, FTIR, TGA and XPS, the effects of various parameters on the lithium uptake capacity of the adsorbent were examined. The analysis of equilibrium data by several adsorption models showed that maximum adsorption capacity of the adsorbent was found to be 9.60 mg/g at 25 °C by the Langmuir model. As initial concentration and contact time increased, adsorption capacity also increased, however, mild temperature (25-35 °C) and pH (5-6) were better for the adsorption of lithium. 80% of lithium adsorption within three minutes proved the fast kinetic nature of the adsorbent. A 99.5% desorption efficiency of lithium was achieved with 0.5 M H2SO4, among HCl and NaCl with different molarities. Phosphorylated cellulose was shown to be a favorable adsorbent for the recovery of lithium from aqueous solutions."

Adsorption and Deposition of Cu (II) on Modified Valonia Tannin

2009 ◽  
Vol 620-622 ◽  
pp. 555-558
Author(s):  
Yi Li ◽  
Xue Gang Luo ◽  
Zhao Liu ◽  
Yan Huang ◽  
Xiao Yan Long
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Mannich Reaction ◽  
Langmuir Isotherm ◽  
Freundlich Isotherm ◽  
Heterogeneous Surface ◽  
Isotherm Model ◽  
Maximum Adsorption Capacity ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model

The modified valonian tannin was prepared through sulfonated-mannich reaction and used to adsorb Cu (II) from the aqueous solutions. The adsorption capacity rapidly reached equilibrium within 2 hours. The effect of pH on adsorption was apparent, the amount of adsorption increased significantly as the pH increased from 2.0 to 4.0 and then leveled off at pH 4.0-6.0. Equilibrium data fitted well with Freundlich isotherm model compared to Langmuir isotherm model, indicating that adsorption takes place on heterogeneous surface of the modified valonia tannin. The adsorption capacity was increased by increasing initial concentrations. The maximum adsorption capacity of cooper ion was determined to be 56.200 mg/g at 100 mg/L concentration.

scholarly journals Enhanced Adsorption of Bisphenol A from Aqueous Solution with 2-Vinylpyridine Functionalized Magnetic Nanoparticles

Polymers ◽  
2018 ◽  
Vol 10 (10) ◽  
pp. 1136 ◽  
Author(s):  
Qiang Li ◽  
Fei Pan ◽  
Wentao Li ◽  
Dongya Li ◽  
Haiming Xu ◽  
...  
Keyword(s):  
Bisphenol A ◽  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Magnetic Nanoparticle ◽  
Maximum Adsorption Capacity ◽  
Salting Out ◽  
Functionalized Magnetic Nanoparticles ◽  
Ft Ir ◽  
Fe3o4 Nanospheres ◽  
Enhanced Adsorption

In this study, a novel 2-vinylpyridine functionalized magnetic nanoparticle (Mag-PVP) was successfully prepared. The prepared Mag-PVP was characterized by transmission electronic microscopy (TEM), Fourier transform infrared spectrophotometry (FT-IR), vibrating sample magnetometry (VSM) and thermogravimetric analysis (TGA), and was used for the adsorption of bisphenol A (BPA) from aqueous solutions. Mag-PVP, which is composed of Fe3O4 nanoparticles and poly divinylbenzene-2-vinylpyridine (with a thickness of 10 nm), exhibited magnetic properties (Ms = 44.6 emu/g) and thermal stability. The maximum adsorption capacity (Qm) of Mag-PVP for BPA obtained from the Langmuir isotherm was 115.87 mg/g at 20 °C, which was more than that of Fe3O4 nanospheres. In the presence of NaCl, the improved adsorption capacity of Mag-PVP was probably attributed to the screening effect of Mag-PVP surface charge and salting-out effect. In the presence of CaCl2 and humic acid (HA), the adsorption capacity of BPA decreased due to competitive adsorption. The adsorption of BPA by Mag-PVP increased slightly with the increase in pH from 3.0 to 5.0 and obtained the largest adsorption amount at pH 5.0, which was probably attributed to hydrogen bonding interactions. Moreover, in actual water, Mag-PVP still showed excellent adsorption performance in removing BPA. The high adsorption capacity and excellent reusability performance in this work indicated that Mag-PVP was an effective adsorbent for removing BPA from aqueous solutions.

scholarly journals Fabrication of Carboxymethylcellulose/Metal-Organic Framework Beads for Removal of Pb(II) from Aqueous Solution

Materials ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 942 ◽  
Author(s):  
Huo-Xi Jin ◽  
Hong Xu ◽  
Nan Wang ◽  
Li-Ye Yang ◽  
Yang-Guang Wang ◽  
...  
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Photoelectron Spectroscopy ◽  
Langmuir Isotherm ◽  
Adsorption Equilibrium ◽  
Isotherm Model ◽  
Maximum Adsorption Capacity ◽  
X Ray ◽  
Metal Organic ◽  
Langmuir Isotherm Model

The ability to remove toxic heavy metals, such as Pb(II), from the environment is an important objective from both human-health and ecological perspectives. Herein, we describe the fabrication of a novel carboxymethylcellulose-coated metal organic material (MOF-5–CMC) adsorbent that removed lead ions from aqueous solutions. The adsorption material was characterized by Fourier-transform infrared spectroscopy, X-ray diffractometry, scanning electron microscopy, and X-ray photoelectron spectroscopy. We studied the functions of the contact time, pH, the original concentration of the Pb(II) solution, and adsorption temperature on adsorption capacity. MOF-5–CMC beads exhibit good adsorption performance; the maximum adsorption capacity obtained from the Langmuir isotherm-model is 322.58 mg/g, and the adsorption equilibrium was reached in 120 min at a concentration of 300 mg/L. The adsorption kinetics is well described by pseudo-second-order kinetics, and the adsorption equilibrium data are well fitted to the Langmuir isotherm model (R2 = 0.988). Thermodynamics experiments indicate that the adsorption process is both spontaneous and endothermic. In addition, the adsorbent is reusable. We conclude that MOF-5–CMC is a good adsorbent that can be used to remove Pb(II) from aqueous solutions.

Ouricuri (Syagrus coronata) fiber: a novel biosorbent to remove methylene blue from aqueous solutions

2016 ◽  
Vol 75 (1) ◽  
pp. 106-114 ◽  
Author(s):  
Lucas Meili ◽  
Társila Santos da Silva ◽  
Daniely Carlos Henrique ◽  
João Inácio Soletti ◽  
Sandra Helena Vieira de Carvalho ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Experimental Design ◽  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Adsorption Process ◽  
Fiber Diameter ◽  
Aqueous Media ◽  
Process Efficiency ◽  
Maximum Adsorption Capacity ◽  
Equilibrium Studies

In this work, the potential of ouricuri (Syagrus coronata) fiber as a novel biosorbent to remove methylene blue (MB) from aqueous solutions was investigated. The fiber was prepared and characterized according to the fundamental features for adsorption. A 23 experimental design was used to evaluate the effects of adsorbent dosage (M), fiber diameter (D) and agitation (A) on the adsorption capacity. In the more adequate conditions, kinetic and equilibrium studies were performed. The experimental design results showed that M = 10 g L−1), D = 0.595 mm and A = 200 rpm were the more adequate conditions for MB adsorption. Based on the kinetic study, it was found that the adsorption process was fast, being the equilibrium was attained at about 5 min, with 90% of color removal. The isotherm was properly represented by the Sips model, and the maximum adsorption capacity was 31.7 mg g−1. In brief, it was demonstrated that ouricuri fiber is an alternative biosorbent to remove MB from aqueous media, taking into account the process efficiency and economic viewpoint.

scholarly journals Adsorption Study of Cu2+ Ions from Aqueous Solutions by Bael Flowers (Aegle marmelos)

2020 ◽  
Vol 11 (4) ◽  
pp. 11891-11904
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Metal Ion ◽  
Low Cost ◽  
Sem Analysis ◽  
Ion Concentration ◽  
Maximum Adsorption Capacity ◽  
Aegle Marmelos ◽  
Batch Mode ◽  
Initial Ph

In the present study, batch mode adsorption was carried out to investigate the adsorption capacity of dried bael flowers (Aegle marmelos) for the adsorptive removal of Cu(II) ions from aqueous solutions by varying agitation time, initial metal concentration, the dose of adsorbent, temperature, and initial pH of the Cu(II) ion solution. The percentage removal of 98.7% was observed at 50 ppm initial metal ion concentration, 0.5 g/100.00 cm3 adsorbent dosage, within the contact time of 120 minutes at 30 ºC in the pH range of 4 – 7. The sorption processes of Cu(II) ions was best described by pseudo-second-order kinetics. Langmuir isotherm had a good fit with the experimental data with 0.97 of correlation coefficient (R2), and the maximum adsorption capacity obtained was 23.14 mg g-1 at 30 ºC. The results obtained from sorption thermodynamic studies suggested that the adsorption process is exothermic and spontaneous. SEM analysis showed tubular voids on the adsorbent. FTIR studies indicated the presence of functional groups like hydroxyl, –C-O, –C=O, and amide groups in the adsorbent, which can probably involve in metal ion adsorption. Therefore, dried bael flowers can be considered an effective low-cost adsorbent for treating Cu(II) ions.

scholarly journals Utilization to Remove Pb (II) Ions from Aqueous Environments Using Waste Fish Bones by Ion Exchange

2014 ◽  
Vol 2014 ◽  
pp. 1-12 ◽  
Author(s):  
Bayram Kizilkaya ◽  
A. Adem Tekınay
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Mechanism ◽  
Cost Effective ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Fish Bones ◽  
Adsorption Capacities ◽  
Aqueous Environments ◽  
Equilibrium Data ◽  
Pseudo Second Order

Removal of lead (II) from aqueous solutions was studied by using pretreated fish bones as natural, cost-effective, waste sorbents. The effect of pH, contact time, temperature, and metal concentration on the adsorption capacities of the adsorbent was investigated. The maximum adsorption capacity for Pb (II) was found to be 323 mg/g at optimum conditions. The experiments showed that when pH increased, an increase in the adsorbed amount of metal of the fish bones was observed. The kinetic results of adsorption obeyed a pseudo second-order model. Freundlich and Langmuir isotherm models were applied to experimental equilibrium data of Pb (II) adsorption and the value ofRLfor Pb (II) was found to be 0.906. The thermodynamic parameters related to the adsorption process such asEa,ΔG°,ΔH°, andΔS° were calculated andEa,ΔH°, andΔS° were found to be 7.06, 46.01 kJ mol−1, and 0.141 kJ mol−1K−1for Pb (III), respectively.ΔH° values (46.01 kJmol−1) showed that the adsorption mechanism was endothermic. Weber-Morris and Urano-Tachikawa diffusion models were also applied to the experimental equilibrium data. The fish bones were effectively used as sorbent for the removal of Pb (II) ions from aqueous solutions.

scholarly journals Removal of Cu(II) from Aqueous Solutions Using Amine-Doped Polyacrylonitrile Fibers

2020 ◽  
Vol 10 (5) ◽  
pp. 1738
Author(s):  
Kay Thwe Aung ◽  
Seung-Hee Hong ◽  
Seong-Jik Park ◽  
Chang-Gu Lee
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Equilibrium Studies ◽  
Naoh Solution ◽  
Surface Modified ◽  
Pan Fibers

Polyacrylonitrile (PAN) fibers were prepared via electrospinning and were modified with diethylenetriamine (DETA) to fabricate surface-modified PAN fibers. The surface-modified PAN fibers were used to evaluate their adsorption capacity for the removal of Cu(II) from aqueous solutions. Batch adsorption experiments were performed to examine the effects of the modification process, initial concentration, initial pH, and adsorbent dose on the adsorption of Cu(II). Kinetic analysis revealed that the experimental data fitted the pseudo-second-order kinetic model better than the pseudo-first-order model. Adsorption equilibrium studies were conducted using the Freundlich and Langmuir isotherm models, and the findings indicated that the PAN fibers modified with 85% DETA presented the highest adsorption capacity for Cu(II) of all analyzed samples. Moreover, the results revealed that the Freundlich model was more appropriate than the Langmuir one for describing the adsorption of Cu(II) onto the modified fibers at various initial Cu(II) concentrations. The maximum adsorption capacity was determined to be 87.77 mg/g at pH 4, and the percent removal of Cu(II) increased as the amount of adsorbent increased. Furthermore, the surface-modified PAN fibers could be easily regenerated using NaOH solution. Therefore, surface-modified PAN fibers could be used as adsorbents for the removal of Cu(II) from aqueous solutions.

Preparation of Graphene Oxide Modified Rice Husk for Cr(VI) Removal

2019 ◽  
Vol 19 (11) ◽  
pp. 7035-7043 ◽  
Author(s):  
Tong Ouyang ◽  
Jidan Tang ◽  
Fang Liu ◽  
Chang-Tang Chang
Keyword(s):  
Graphene Oxide ◽  
Adsorption Capacity ◽  
Rice Husk ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Adsorption Sites ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Alkaline Conditions ◽  
Rice Husk Biochar

The objective of this paper is to study the removal of Cr(VI) in aqueous solution by using a new graphene oxide-coated rice husk biochar composite (GO-RHB). GO-RHB is a synthetic material having a porous structure with lots of oxygen-containing functional groups and a large surface area that provide effective adsorption sites. Experiments showed that GO-RHB had higher adsorption capacity under acidic than under alkaline conditions. At pH of 2, GO-RHB has the maximum adsorption capacity(48.8 mg g−1). Equilibrium data obtained by fitting with the Langmuir and Freundlich models indicate that the reaction process was monolayer adsorption. The adsorption of Cr(VI) followed the pseudo-second-order kinetic model that illustrates chemical adsorption. Intraparticlediffusion studies further revealed that film diffusion was taking place. Moreover, the results of thermodynamics showed that the adsorption process was endothermic and spontaneous in nature. The removal mechanism of Cr(VI) was also explained in detail. The prepared adsorbent is highly efficient and might be useful than many other conventional adsorbent used for the removal of Cr(VI) from wastewater.

Novel Amphoteric Cryogels for Cd2+ Ions Removal from Aqueous Solutions

2018 ◽  
Vol 775 ◽  
pp. 376-382 ◽  
Author(s):  
Alzhan Baimenov ◽  
Dmitriy Berillo ◽  
Leila Abylgazina ◽  
Stavros G. Poulopoulos ◽  
Vassilis J. Inglezakis
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Chemical Structure ◽  
Nitrogen Adsorption ◽  
Maximum Adsorption Capacity ◽  
Cadmium Ions ◽  
Texture Analyzer ◽  
Ph Values ◽  
Amphoteric Properties ◽  
Scanning Electron

In this work, amphoteric cryogels based on N,N-dimethyl acrylamide, methacrylic acid and allylamine, crosslinked by N,N-methylenebisacrylamide were synthesized by free-radical polymerization in cryo-conditions. The synthesized cryogels were used for the removal of cadmium ions from aqueous solutions under different pH values. The chemical structure was studied by FTIR, porosity by nitrogen adsorption and morphology by scanning electron microscopy and texture analyzer. The amphoteric properties of cryogels were studied by zeta potential measurements. Adsorption tests revealed that cryogels exhibit 3 times higher adsorption capacity at pH 6.0 than at pH 4.0. The maximum adsorption capacity of the amphoteric cryogels for Cd2+ was 113 mg/g, at pH 6.0 and initial Cd2+ concentration 100 ppm. The results suggest that the predominant removal mechanism is ion exchange between sodium, which initially presents in the structure of the cryogel, and cadmium from the aqueous phase. Recovery studies suggested that the cryogels used can be regenerated and efficiently reused.

scholarly journals Modified Chitosan for Silver Recovery—Kinetics, Thermodynamic, and Equilibrium Studies

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 657 ◽  
Author(s):  
Bogdan Pascu ◽  
Cristina Ardean ◽  
Corneliu Mircea Davidescu ◽  
Adina Negrea ◽  
Mihaela Ciopec ◽  
...  
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Maximum Efficiency ◽  
Metallic Silver ◽  
Maximum Adsorption Capacity ◽  
Silver Recovery ◽  
Equilibrium Studies ◽  
Environment Friendly ◽  
Modified Chitosan ◽  
Materials Used

The aim of this study is to investigate the silver recovery from aqueous solutions. There are a variety of recovery methods, such as hydrometallurgical, bio-metallurgical, cementation, reduction, electrocoagulation, electrodialysis, ion exchange, etc. Adsorption represents a convenient, environment friendly procedure, that can be used to recover silver from aqueous solutions. In this paper we highlight the silver adsorption mechanism on chitosan chemically modified with active groups, through kinetic, thermodynamic, and equilibrium studies. A maximum adsorption capacity of 103.6 mg Ag(I)/g of adsorbent for an initial concentration of 700 mg/L was noticed by using modified chitosan. Lower adsorption capacity has been noticed in unmodified chitosan—a maximum of 75.43 mg Ag(I)/g. Optimum contact time was 120 min and the process had a maximum efficiency when conducted at pH higher than 6. At the same time, a way is presented to obtain metallic silver from the adsorbent materials used for the recovery of the silver from aqueous solutions.

Sign in / Sign up

Export Citation Format

Share Document