Nanostructure of Fe-C Alloys Prepared by Arc Melting in Vacuum

2017 ◽  
Vol 45 ◽  
pp. 218-228
Author(s):  
V. Karoutsos ◽  
Odyseas Venetsanos ◽  
Dimitris Geralis ◽  
Panagiotis Poulopoulos ◽  
C. Politis
Keyword(s):  
Lamellar Spacing ◽  
Isothermal Transformation ◽  
X Ray Diffraction ◽  
X Ray ◽  
Arc Melting ◽  
Heat Treated ◽  
Mean Size ◽  
Carbon Mapping ◽  
The One ◽  
Treatment Procedures

Three different Fe-C alloys were prepared in vacuum using the arc melting method: hypereutectoid (1.4% C), eutectoid (0.76% C) and hypoeutectoid (0.4% C). Unlike commercial steels, which they always contain Mn and other impurities, our samples were prepared by using high quality powders (99.999 wt.%). The samples were heat-treated and then observed with optical and scanning electronic microscopy (Zeiss EVO MA10). Selected samples were tested by microidentation (microhardness test). After isothermal transformation at 350 °C fine bainite nanostructures were observed in the hypoeutectoid sample, the mean size of which was found to be 50 nm. With the eutectoid sample, following different heat treatment procedures different micro-and nanostructures were measured: pearlite lamellar spacing, spheroidized cementite particles, and martensite needles, whose mean size is 145 nm, 290 nm and 200 nm respectively. The nanostructure of hypereutectoid sample after isothermal transformation at 650 °C, reveals the eutectoid and proeutectoid cementite lamellas with a mean spacing of 390 nm. X-ray diffraction pattern of eutectoid sample indicated the existence of cementite (Fe3C) content which is also confirmed by carbon mapping of pearlite colonies performed with Energy Dispersive X-ray Spectroscopy. The Vickers hardness of the samples compares well to the one of corresponding commercial steels.

scholarly journals Stable and Metastable Phase Equilibria Involving the Cu6Sn5 Intermetallic

2021 ◽  
Author(s):  
A. Leineweber ◽  
M. Löffler ◽  
S. Martin
Keyword(s):  
Phase Equilibria ◽  
Electron Backscatter Diffraction ◽  
Metastable Phase ◽  
Stable Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Heat Treated ◽  
Ordered Phases ◽  
Backscatter Diffraction ◽  
Kinetics Of

Abstract Cu6Sn5 intermetallic occurs in the form of differently ordered phases η, η′ and η′′. In solder joints, this intermetallic can undergo changes in composition and the state of order without or while interacting with excess Cu and excess Sn in the system, potentially giving rise to detrimental changes in the mechanical properties of the solder. In order to study such processes in fundamental detail and to get more detailed information about the metastable and stable phase equilibria, model alloys consisting of Cu3Sn + Cu6Sn5 as well as Cu6Sn5 + Sn-rich melt were heat treated. Powder x-ray diffraction and scanning electron microscopy supplemented by electron backscatter diffraction were used to investigate the structural and microstructural changes. It was shown that Sn-poor η can increase its Sn content by Cu3Sn precipitation at grain boundaries or by uptake of Sn from the Sn-rich melt. From the kinetics of the former process at 513 K and the grain size of the η phase, we obtained an interdiffusion coefficient in η of (3 ± 1) × 10−16 m2 s−1. Comparison of this value with literature data implies that this value reflects pure volume (inter)diffusion, while Cu6Sn5 growth at low temperature is typically strongly influenced by grain-boundary diffusion. These investigations also confirm that η′′ forming below a composition-dependent transus temperature gradually enriches in Sn content, confirming that Sn-poor η′′ is metastable against decomposition into Cu3Sn and more Sn-rich η or (at lower temperatures) η′. Graphic Abstract

scholarly journals ZnOTe Compounds Grown by DC-Magnetron Co-Sputtering

Coatings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 570
Author(s):  
Olga Sánchez ◽  
Manuel Hernández-Vélez
Keyword(s):  
Molar Fraction ◽  
Variable Parameter ◽  
Point Of View ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sample Series ◽  
Solid Phases ◽  
The One ◽  
High Bulk ◽  
Substrate Sample

ZnOTe compounds were grown by DC magnetron cosputtering from pure Tellurium (Te) and Zinc (Zn) cathodes in O2/Ar atmosphere. The applied power on the Zn target was constant equal to 100 W, while the one applied on the Te target took two values, i.e., 5 W and 10 W. Thus, two sample series were obtained in which the variable parameter was the distance from the Te targets to the substrate. Sample compositions were determined by Rutherford Backscattering Spectroscopy (RBS) experiments. Structural analysis was done using X-Ray diffraction (XRD) spectrometry and the growth of the hexagonal w-ZnO phase was identified in the XRD spectra. RBS results showed high bulk homogeneity of the samples forming ZnOTe alloys, with variable Te molar fraction (MF) ranging from 0.48–0.6% and from 1.9–3.1% for the sample series obtained at 5 W and 10 W, respectively. The results reflect great differences between the two sample series, particularly from the structural and optical point of view. These experiments point to the possibility of Te doping ZnO with the permanence of intrinsic defects, as well as the possibility of the formation of other Te solid phases when its content increases. The results and appreciable variations in the band gap transitions were detected from Photoluminescence (PL) measurements.

scholarly journals Study of Structural, Magnetic, and Mossbauer Properties of Dy2Fe16Ga1−xNbx (0.0 ≤ x ≤ 1.0) Prepared via Arc Melting Process

2021 ◽  
Vol 7 (3) ◽  
pp. 42
Author(s):  
Jiba N. Dahal ◽  
Kalangala Sikkanther Syed Ali ◽  
Sanjay R. Mishra
Keyword(s):  
Isomer Shift ◽  
Cell Volume ◽  
Intermetallic Compounds ◽  
Unit Cell Volume ◽  
Rietveld Analysis ◽  
Unit Cell ◽  
X Ray Diffraction ◽  
X Ray ◽  
Arc Melting ◽  
Nb Content

Intermetallic compounds of Dy2Fe16Ga1−xNbx (x = 0.0 to 1.00) were synthesized by arc melting. Samples were investigated for structural, magnetic, and hyperfine properties using X-ray diffraction, vibration sample magnetometer, and Mossbauer spectrometer, respectively. The Rietveld analysis of room temperature X-ray diffraction data shows that all the samples were crystallized in Th2Fe17 structure. The unit cell volume of alloys increased linearly with an increase in Nb content. The maximum Curie temperature Tc ~523 K for x = 0.6 sample is higher than Tc = 153 K of Dy2Fe17. The saturation magnetization decreased linearly with increasing Nb content from 61.57 emu/g for x = 0.0 to 42.46 emu/g for x = 1.0. The Mössbauer spectra and Rietveld analysis showed a small amount of DyFe3 and NbFe2 secondary phases at x = 1.0. The hyperfine field of Dy2Fe16Ga1−xNbx decreased while the isomer shift values increased with the Nb content. The observed increase in isomer shift may have resulted from the decrease in s electron density due to the unit cell volume expansion. The substantial increase in Tc of thus prepared intermetallic compounds is expected to have implications in magnets used for high-temperature applications.

Ternary Antimonides RE4T7Sb6 (RE=Gd–Lu; T =Ru, Rh) with Cubic U4Re7Si6-type Structure

2013 ◽  
Vol 68 (9) ◽  
pp. 971-978 ◽  
Author(s):  
Inga Schellenberg ◽  
Ute Ch. Rodewald ◽  
Christian Schwickert ◽  
Matthias Eul ◽  
Rainer Pöttgen
Keyword(s):  
Magnetic Susceptibility ◽  
Single Crystal ◽  
Magnetic Moment ◽  
Induction Furnace ◽  
X Ray Diffraction ◽  
Temperature Dependent ◽  
X Ray ◽  
Antiferromagnetic Ordering ◽  
Arc Melting ◽  
Intermediate Valent

The ternary antimonides RE4T7Sb6 (RE=Gd-Lu; T =Ru, Rh) have been synthesized from the elements by arc-melting and subsequent annealing in an induction furnace. The samples have been characterized by powder X-ray diffraction. Four structures were refined on the basis of single-crystal X-ray diffractometer data: U4Re7Si6 type, space group Im3m with a=862.9(2) pm, wR2=0.0296, 163 F2 values for Er4Ru7Sb6; a=864.1(1) pm, wR2=0.1423, 153 F2 values for Yb4Ru7Sb6; a=872.0(2) pm, wR2=0.0427, 172 F2 values for Tb4Rh7Sb6; and a=868.0(2) pm, wR2=0.0529, 154 F2 values for Er4Rh7Sb6, with 10 variables per refinement. The structures have T1@Sb6 octahedra and slightly distorted RE@T26Sb6 cuboctahedra as building units. The distorted cuboctahedra are condensed via all trapezoidal faces, and this network leaves octahedral voids for the T1 atoms. The ruthenium-based series of compounds was studied by temperature-dependent magnetic susceptibility measurements. Lu4Ru7Sb6 is Pauli-paramagnetic. The antimonides RE4Ru7Sb6 with RE=Dy, Ho, Er, and Tm show Curie-Weiss paramagnetism. Antiferromagnetic ordering occurs at 10.0(5), 5.1(5) and 4.0(5) K for Dy4Ru7Sb6, Ho4Ru7Sb6 and Er4Ru7Sb6, respectively, while Tm4Ru7Sb6 remains paramagnetic. Yb4Ru7Sb6 is an intermediate-valent compound with a reduced magnetic moment of 3.71(1) μB per Yb as compared to 4.54 μB for a free Yb3+ ion

PREPARATION OF ANTIMONY-PLATINUM SURFACE ALLOY ELECTRODE BY ATOM DIFFUSION IN THE SOLID PHASE

2006 ◽  
Vol 20 (25n27) ◽  
pp. 3999-4004
Author(s):  
HIROSHI MATSUI ◽  
KAZUFUMI WATANABE
Keyword(s):  
Diffraction Pattern ◽  
Low Temperatures ◽  
Solid Phase ◽  
Electrochemical Measurement ◽  
X Ray Diffraction ◽  
Platinum Surface ◽  
X Ray ◽  
Atom Diffusion ◽  
Heat Treated ◽  
Titanium Substrates

Antimony-platinum bilayers were prepared on titanium substrates by the two-step electrodeposition in the usual baths, and then surface alloys were formed by the atom diffusion in the solid phase. The simple antimony layer was little influenced by the substrate in both the measurements of X-ray diffraction and the i - E characteristic in a sulfuric acid solution. Regarding the bilayers, the catalytic activity in hydrogen evolution reaction was very sensitive to the presence of platinum, while the hydrogen adsorbability was quite insensitive. An interaction between antimony and platinum was confirmed by the appearance of a new dissolution wave in the electrochemical measurement and the occurrence of a new diffraction in the X-ray diffraction pattern after the heat-treatment of about 400°C. Although the new diffraction disagreed with any of the reported alloys, clear diffraction pattern of PtSb 2 alloy was observed, when the bilayers were heat-treated at about 600°C for one hour. Considering the penetration depth of X-ray, the alloying of antimony and platinum seems to occur also at low temperatures at least at the top surface.

Effect of Nickel on Titanium Carbide Synthesized via Tungsten Inert Gas (TIG) Method

2012 ◽  
Vol 620 ◽  
pp. 384-388
Author(s):  
Sharifah Aishah Syed Salim ◽  
Julie Juliewatty Mohamed ◽  
Zainal Arifin Ahmad ◽  
Zainal Arifin Ahmad
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Powder Mixture ◽  
Raw Material ◽  
Inert Gas ◽  
X Ray Diffraction ◽  
X Ray ◽  
Arc Melting ◽  
Elemental Powder Mixture ◽  
Scanning Electron

Numerous methods have been used to produce high purity TiC. There is no previous study has been reported on the formation using single elemental powders of Titanium (Ti) and Carbon (C) with addition Nickel (Ni) by tungsten inert gas (TIG) weld method. In this work, TiC was synthesized via TIG method by arc melting elemental powder mixture of Ti and C at ~5 second (s) and 80 ampere (A). The effect Ni contents on TiC formation was investigated. The mixed raw material was ball milled for 24 hours followed by synthesis via TIG method. The arced samples were characterized by X-ray diffraction (XRD) and Scanning electron microscope (SEM). It was revealed, that small amount of Ni additive to the metal powder allows the production of dense and tough TiC.

A Novel Hydroxyapatite Carrier for Enrichment of Hydrocarbon Degradation Bacteria

2007 ◽  
Vol 336-338 ◽  
pp. 1914-1917
Author(s):  
Lei Yang ◽  
Zhen Yi Zhang ◽  
Xiao Shan Ning ◽  
Guang He Li
Keyword(s):  
Activated Carbon ◽  
Sol Gel ◽  
Hydrocarbon Degradation ◽  
Potential Candidate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Bacterial Enrichment ◽  
Bet Method ◽  
The One ◽  
Scanning Electron

In this paper, a novel and highly efficient hydroxyapatite (HA) carrier for cultivating hydrocarbon degradation bacteria (HDB) is introduced. The HA particles synthesized through a sol-gel method and different heat treatments were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and BET method. The microbial amount and activities of HDB cultivated on HA carriers were quantitatively investigated in order to assess their enriching capabilities. The results showed that HA synthesized at 550°C and the one without calcination could enrich HDB 3 and 2 magnitude orders more than the activated carbon, respectively. Mechanisms of bacterial enrichment on HA and activated carbon were also studied, and it is believed that the high bioactivity and the surface morphology of HA were responsible for the efficient reproduction of HDB. It is concluded that HA is a potential candidate to replace the conventionally used activated carbon as a novel carrier applied in the filed of bioremediation for oil contaminated soil.

Microstructure and Mechanical Properties of VTaTiMoAlx Refractory High Entropy Alloys

2017 ◽  
Vol 898 ◽  
pp. 638-642 ◽  
Author(s):  
Dong Xu Qiao ◽  
Hui Jiang ◽  
Xiao Xue Chang ◽  
Yi Ping Lu ◽  
Ting Ju Li
Keyword(s):  
Mechanical Properties ◽  
Vacuum Arc ◽  
High Entropy Alloys ◽  
X Ray Diffraction ◽  
Dendrite Structure ◽  
X Ray ◽  
High Entropy ◽  
Arc Melting ◽  
Vacuum Arc Melting ◽  
Microstructure And Mechanical Properties

A series of refractory high-entropy alloys VTaTiMoAlx with x=0,0.2,0.6,1.0 were designed and produced by vacuum arc melting. The effect of added Al elements on the microstructure and mechanical properties of refractory high-entropy alloys were investigated. The X-ray diffraction results showed that all the high-entropy alloys consist of simple BCC solid solution. SEM indicated that the microstructure of VTaTiMoAlx changes from equiaxial dendritic-like structure to typical dendrite structure with the addition of Al element. The composition of different regions in the alloys are obtained by energy dispersive spectroscopy and shows that Ta, Mo elements are enriched in the dendrite areas, and Al, Ti, V are enriched in inter-dendrite areas. The yield strength and compress strain reach maximum (σ0.2=1221MPa, ε=9.91%) at x=0, and decrease with the addition of Al element at room temperature. Vickers hardness of the alloys improves as the Al addition.

Superstructure formation in the solid solution Sc3Pt3−xIn3 (x = 0–0.93)

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Nataliya L. Gulay ◽  
Rolf-Dieter Hoffmann ◽  
Jutta Kösters ◽  
Yaroslav M. Kalychak ◽  
Stefan Seidel ◽  
...  
Keyword(s):  
Solid Solution ◽  
Diffraction Data ◽  
High Frequency ◽  
Lattice Parameters ◽  
X Ray Diffraction ◽  
Space Group ◽  
X Ray ◽  
Platinum Content ◽  
Arc Melting ◽  
Modulation Vector

Abstract The equiatomic indide ScPtIn (ZrNiAl type, space group P 6 ‾ $‾{6}$ 2m) shows an extended solid solution Sc3Pt3–xIn3. Several samples of the Sc3Pt3–xIn3 series were synthesized from the elements by arc-melting and subsequent annealing, or directly in a high frequency furnace. The lowest platinum content was observed for Sc3Pt2.072(3)In3. All samples were characterized by powder X-ray diffraction and their lattice parameters and several single crystals were studied on the basis of precise single crystal X-ray diffractometer data. The correct platinum occupancy parameters were refined from the diffraction data. Decreasing platinum content leads to decreasing a and c lattice parameters. Satellite reflections were observed for the Sc3Pt3–xIn3 crystals with x = 0.31–0.83. These satellite reflections could be described with a modulation vector ( 1 3 , 1 3 , γ ) $\left(\frac{1}{3},\frac{1}{3},\gamma \right)$ ( γ = 1 2 $\gamma =\frac{1}{2}$ c* for all crystals) and are compatible with trigonal symmetry. The interplay of platinum filled vs. empty In6 trigonal prisms is discussed for an approximant structure with space group P3m1.

Hardening of Selective Laser Melted M2 Steel

2021 ◽  
Author(s):  
Mei Yang ◽  
Yishu Zhang ◽  
Haoxing You ◽  
Richard Smith ◽  
Richard D. Sisson
Keyword(s):  
Heat Treatment ◽  
High Speed ◽  
Cutting Tools ◽  
High Speed Steel ◽  
High Hardness ◽  
Steel Part ◽  
X Ray Diffraction ◽  
X Ray ◽  
Heat Treated ◽  
Near Net Shape

Abstract Selective laser melting (SLM) is an additive manufacturing technique that can be used to make the near-net-shape metal parts. M2 is a high-speed steel widely used in cutting tools, which is due to its high hardness of this steel. Conventionally, the hardening heat treatment process, including quenching and tempering, is conducted to achieve the high hardness for M2 wrought parts. It was debated if the hardening is needed for additively manufactured M2 parts. In the present work, the M2 steel part is fabricated by SLM. It is found that the hardness of as-fabricated M2 SLM parts is much lower than the hardened M2 wrought parts. The characterization was conducted including X-ray diffraction (XRD), optical microscopy, Scanning Electron Microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS) to investigate the microstructure evolution of as-fabricated, quenched, and tempered M2 SLM part. The M2 wrought part was heat-treated simultaneously with the SLM part for comparison. It was found the hardness of M2 SLM part after heat treatment is increased and comparable to the wrought part. Both quenched and tempered M2 SLM and wrought parts have the same microstructure, while the size of the carbides in the wrought part is larger than that in the SLM part.

Sign in / Sign up

Export Citation Format

Share Document