Phase Stability and Mechanical Properties of Ti(Ni, Ru) Alloys

2002 ◽  
Vol 753 ◽  
Author(s):  
Masahiro Tsuji ◽  
Hideki Hosoda ◽  
Kenji Wakashima ◽  
Yoko Yamabe-Mitarai
Keyword(s):  
Mechanical Properties ◽  
Phase Transformation ◽  
Phase Stability ◽  
Hot Forging ◽  
Tensile Tests ◽  
Lattice Parameter ◽  
Solid Solution Hardening ◽  
Scanning Calorimetry ◽  
Arc Melting ◽  
Transmission Electron

ABSTRACTEffects of ruthenium (Ru) substitution on constituent phases, phase transformation temperatures and mechanical properties were investigated for Ti-Ni shape memory alloys. Ti50Ni50-XRuX alloys with Ru contents (X) from 0mol% (binary TiNi) to 50mol% (binary TiRu) were systematically prepared by Ar arc-melting followed by hot-forging at temperatures from 1173K to 1673K depending on chemical composition. Phase stability was assessed by DSC (differential scanning calorimetry), XRD (X-ray diffractometry) and TEM (transmission electron microscopy). Mechanical properties were investigated using hardness and tensile tests at room temperature. With increasing Ru content, it was found that the lattice parameter of B2 phase increases, the martensitic transformation temperature slightly decreases, and the melting temperature increases monotonously. Besides, R-phase appears for Ti-Ni alloys containing 3mol% and 20mol%Ru but no diffusionless phase transformation is seen in Ti-Ni alloy containing 5mol%Ru. Vickers hardness shows the maximum at an intermediate composition (HV1030 at 30mol%Ru); this suggests that large solid solution hardening is caused by Ru substitution for the Ni-sites in TiNi.

scholarly journals FEATURES OF STRUCTURE FORMATION AND CHANGES IN THE MECHANICAL PROPERTIES OF CAST Al-Mg-Si-Mn ALLOY WITH THE ADDITION OF (Ti+Zr)

2015 ◽  
Vol 55 (4) ◽  
pp. 282 ◽  
Author(s):  
Oleksandr Trudonoshyn ◽  
Maxim Puchnin ◽  
Kostiantyn Mykhalenkov
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Ageing Time ◽  
Tensile Tests ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Heat Treated ◽  
Scanning Electron

<p>The as-cast and heat-treated structure of permanent mould castings of AlMg<sub>5</sub>Si<sub>2</sub>Mn alloys with different contents of Ti has been investigated by differential scanning calorimetry, hardness and microhardness measurements, tensile tests and fractography analyses, scanning electron microscopy, transmission electron microscopy, and energy dispersive X-ray analysis. We have established that α-Al dendrites can be nucleated on an Al-Ti substrate, and also that primary Mg<sub>2</sub>Si crystals can be nucleated on oxides, including oxides of Al and Ti compounds. The dependence of the change in mechanical properties on ageing time, and on the amount of Ti in the alloys, is shown.</p>

scholarly journals Effect of Multiple Reflows on the Interfacial Reactions and Mechanical Properties of an Sn-0.5Cu-Al(Si) Solder and a Cu Substrate

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2367
Author(s):  
Junhyuk Son ◽  
Dong-Yurl Yu ◽  
Yun-Chan Kim ◽  
Shin-Il Kim ◽  
Min-Su Kim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Heat ◽  
Interfacial Reactions ◽  
Future Application ◽  
Scanning Calorimetry ◽  
Cross Sectional ◽  
Automotive Electronic ◽  
Transmission Electron ◽  
Si Content ◽  
Lead Free Solders

In this study, the interfacial reactions and mechanical properties of solder joints after multiple reflows were observed to evaluate the applicability of the developed materials for high-temperature soldering for automotive electronic components. The microstructural changes and mechanical properties of Sn-Cu solders regarding Al(Si) addition and the number of reflows were investigated to determine their reliability under high heat and strong vibrations. Using differential scanning calorimetry, the melting points were measured to be approximately 227, 230, and 231 °C for the SC07 solder, SC-0.01Al(Si), and SC-0.03Al(Si), respectively. The cross-sectional analysis results showed that the total intermetallic compounds (IMCs) of the SC-0.03Al(Si) solder grew the least after the as-reflow, as well as after 10 reflows. Electron probe microanalysis and transmission electron microscopy revealed that the Al-Cu and Cu-Al-Sn IMCs were present inside the solders, and their amounts increased with increasing Al(Si) content. In addition, the Cu6Sn5 IMCs inside the solder became more finely distributed with increasing Al(Si) content. The Sn-0.5Cu-0.03Al(Si) solder exhibited the highest shear strength at the beginning and after 10 reflows, and ductile fracturing was observed in all three solders. This study will facilitate the future application of lead-free solders, such as an Sn-Cu-Al(Si) solder, in automotive electrical components.

scholarly journals Effects of Sintering Temperature on Densification, Microstructure and Mechanical Properties of Al-Based Alloy by High-Velocity Compaction

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 218
Author(s):  
Xianjie Yuan ◽  
Xuanhui Qu ◽  
Haiqing Yin ◽  
Zaiqiang Feng ◽  
Mingqi Tang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Velocity ◽  
Sintered Density ◽  
Sintering Temperature ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
High Velocity Compaction ◽  
Sintered Temperature

This present work investigates the effects of sintering temperature on densification, mechanical properties and microstructure of Al-based alloy pressed by high-velocity compaction. The green samples were heated under the flow of high pure (99.99 wt%) N2. The heating rate was 4 °C/min before 315 °C. For reducing the residual stress, the samples were isothermally held for one h. Then, the specimens were respectively heated at the rate of 10 °C/min to the temperature between 540 °C and 700 °C, held for one h, and then furnace-cooled to the room temperature. Results indicate that when the sintered temperature was 640 °C, both the sintered density and mechanical properties was optimum. Differential Scanning Calorimetry, X-ray diffraction of sintered samples, Scanning Electron Microscopy, Energy Dispersive Spectroscopy, and Transmission Electron Microscope were used to analyse the microstructure and phases.

scholarly journals Mechanical, Thermal and Rheological Properties of Polyethylene-Based Composites Filled with Micrometric Aluminum Powder

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1242
Author(s):  
Olga Mysiukiewicz ◽  
Paulina Kosmela ◽  
Mateusz Barczewski ◽  
Aleksander Hejna
Keyword(s):  
Mechanical Properties ◽  
Melt Flow Index ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Flow Index ◽  
Scanning Calorimetry ◽  
Metal Composites ◽  
Pre Treatment ◽  
The Impact ◽  
Properties Of Composites

Investigations related to polymer/metal composites are often limited to the analysis of the electrical and thermal conductivity of the materials. The presented study aims to analyze the impact of aluminum (Al) filler content (from 1 to 20 wt%) on the rarely investigated properties of composites based on the high-density polyethylene (HDPE) matrix. The crystalline structure, rheological (melt flow index and oscillatory rheometry), thermal (differential scanning calorimetry), as well as static (tensile tests, hardness, rebound resilience) and dynamic (dynamical mechanical analysis) mechanical properties of composites were investigated. The incorporation of 1 and 2 wt% of aluminum filler resulted in small enhancements of mechanical properties, while loadings of 5 and 10 wt% provided materials with a similar performance to neat HDPE. Such results were supported by the lack of disturbances in the rheological behavior of composites. The presented results indicate that a significant content of aluminum filler may be introduced into the HDPE matrix without additional pre-treatment and does not cause the deterioration of composites’ performance, which should be considered beneficial when engineering PE/metal composites.

Enhancing the Thermal and Mechanical Characteristics of Polyvinyl Alcohol (PVA)-Hemp Protein Particles (HPP) Composites

2021 ◽  
Vol 36 (2) ◽  
pp. 137-143
Author(s):  
S. A. Awad
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperatures ◽  
Composite Films ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Decomposition Temperature ◽  
Scanning Calorimetry ◽  
Solution Casting Method ◽  
Protein Particles

Abstract This paper aims to describe the thermal, mechanical, and surface properties of a PVA/HPP blend whereby the film was prepared using a solution casting method. The improvements in thermal and mechanical properties of HPP-based PVA composites were investigated. The characterization of pure PVA and PVA composite films included tensile tests, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The results of TGA and DSC indicated that the addition of HPP increased the thermal decomposition temperature of the composites. Mechanical properties are significantly improved in PVA/HPP composites. The thermal stability of the PVA composite increased with the increase of HPP filler content. The tensile strength increased from 15.74 ± 0.72 MPa to 27.54 ± 0.45 MPa and the Young’s modulus increased from 282.51 ± 20.56 MPa to 988.69 ± 42.64 MPa for the 12 wt% HPP doped sample. Dynamic mechanical analysis (DMA) revealed that at elevated temperatures, enhanced mechanical properties because of the presence of HPP was even more noticeable. Morphological observations displayed no signs of agglomeration of HPP fillers even in composites with high HPP loading.

scholarly journals Microstructure and mechanical properties of slowly cooled Cu47.5Zr47.5Al5

2007 ◽  
Vol 22 (2) ◽  
pp. 326-333 ◽  
Author(s):  
J. Das ◽  
S. Pauly ◽  
C. Duhamel ◽  
B.C. Wei ◽  
J. Eckert
Keyword(s):  
Mechanical Properties ◽  
Fracture Strain ◽  
Volume Fraction ◽  
Spherical Shape ◽  
High Yield ◽  
High Yield Strength ◽  
Scanning Calorimetry ◽  
Arc Melting ◽  
Martensite Matrix

Cu47.5Zr47.5Al5 was prepared by arc melting and solidified in situ by suction casting into 2–5-mm-diameter rods under various cooling rates (200–2000 K/s). The microstructure was investigated along the length of the rods by electron microscopy, differential scanning calorimetry and mechanical properties were investigated under compression. The microstructure of differently prepared specimens consists of macroscopic spherical shape chemically inhomogeneous regions together with a low volume fraction of randomly distributed CuZr B2 phase embedded in a 2–7 nm size clustered “glassy-martensite” matrix. The as-cast specimens show high yield strength (1721 MPa), pronounced work-hardening behavior up to 2116 MPa and large fracture strain up to 12.1–15.1%. The fracture strain decreases with increasing casting diameter. The presence of chemical inhomogenities and nanoscale “glassy-martensite” features are beneficial for improving the inherent ductility of the metallic glass.

Initial properties and ageing behaviour of pineapple leaf and palm fibre as reinforcement for polypropylene

2016 ◽  
Vol 30 (2) ◽  
pp. 174-195 ◽  
Author(s):  
Rungsima Chollakup ◽  
Haroutioun Askanian ◽  
Florence Delor-Jestin
Keyword(s):  
Mechanical Properties ◽  
Cost Effective ◽  
Tensile Tests ◽  
Natural Fibre ◽  
Thermal Ageing ◽  
Second Step ◽  
Scanning Calorimetry ◽  
Ultraviolet Exposure ◽  
Palm Fibre

In the furniture, automotive and contruction industries, there is increased demand for cost-effective and lightweight biocomposites. The objective of this work was to develop new natural fibre-based composites with specific properties. Palm and pineapple leaf fibres were chosen in association with polypropylene (PP). The first step was to investigate the effect of these natural fibres as reinforcement for PP. The evolution of chemical structure and crystallinity was proposed with infrared spectroscopy measurements and differential scanning calorimetry thermograms, respectively. The assessments of mechanical properties with tensile tests and melt viscoelastic behaviour were also investigated. The study enabled to distinguish the influence of fibre content. The second step in our work was to assess the composite durability after ultraviolet exposure or thermal ageing. The oxidation level was calculated. The long-term evolution of thermal and mechanical properties was also proposed. As a result, the PP/pineapple leaf composite revealed a promising biocomposite.

The Structure and Mechanical Properties of Plastically Consolidated Al-Ni Alloy

2016 ◽  
Vol 682 ◽  
pp. 245-251 ◽  
Author(s):  
Grzegorz Włoch ◽  
Tomasz Skrzekut ◽  
Jakub Sobota ◽  
Antoni Woźnicki ◽  
Justyna Cisoń
Keyword(s):  
Mechanical Properties ◽  
Vickers Hardness ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Intermetallic Phases ◽  
Scanning Calorimetry ◽  
Porosity Formation ◽  
X Ray ◽  
Ni Alloy ◽  
Thermal Stability Of

Mixed and preliminarily consolidated powders of aluminium and nickel (90 mass % Al and 10 mass % Ni) were hot extruded. As results the rod, 8 mm in diameter, was obtained. As-extruded material was subjected to the microstructural investigations using scanning electron microscopy (SEM/EDS) and X-ray analysis (XRD). The differential scanning calorimetry (DSC) and thermo-mechanical analysis (TMA) were also performed. The mechanical properties of as extruded material were determined by the tensile test and Vickers hardness measurements. In order to evaluate the thermal stability of PM alloy, samples were annealed at the temperature of 475 and 550 °C. After annealing Vickers hardness measurements and tensile tests were carried out. The plastic consolidation of powders during extrusion was found to be very effective, because no pores or voids were observed in the examined material. The detailed microstructural investigations and XRD analyses did not reveal the presence of the intermetallic phases in the as-extruded material. During annealing, the Al3Ni intermetallic compound was formed as the result of chemical reaction between the alloy components. The hardness of the alloy after annealing at the temperature of 475°C was found to be comparable to the hardness in as-extruded state. Annealing of the material at the temperature of 550°C results in hardness decreasing by about 50%, as the consequence of porosity formation and Al3Ni cracking.

Effects of Cooling Rate and Sn Addition on the Microstructure of Ti-Nb-Sn Alloys

2011 ◽  
Vol 172-174 ◽  
pp. 190-195 ◽  
Author(s):  
Giorgia T. Aleixo ◽  
Eder S.N. Lopes ◽  
Rodrigo Contieri ◽  
Alessandra Cremasco ◽  
Conrado Ramos Moreira Afonso ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Melting Furnace ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Β Phase ◽  
Arc Melting ◽  
Ti Alloys ◽  
Ω Phase

Ti-based alloys present unique properties and hence, are employed in several industrial segments. Among Ti alloys, β type alloys form one of the most versatile classes of materials in relation to processing, microstructure and mechanical properties. It is well known that heat treatment of Ti alloys plays an important role in determining their microstructure and mechanical behavior. The aim of this work is to analyze microstructure and phases formed during cooling of β Ti-Nb-Sn alloy through different cooling rates. Initially, samples of Ti-Nb-Sn system were prepared through arc melting furnace. After, they were subjected to continuous cooling experiments to evaluate conditions for obtaining metastable phases. Microstructure analysis, differential scanning calorimetry and X-ray diffraction were performed in order to evaluate phase transformations. Depending on the cooling rate and composition, α” martensite, ω phase and β phase were obtained. Elastic modulus has been found to decrease as the amount of Sn was increased.

Effect of Nitrogen Addition on TiNi Shape Memory Alloys

2020 ◽  
Vol 12 (9) ◽  
pp. 1403-1408
Author(s):  
Izaz Ur Rehman ◽  
Tae-Hyun Nam
Keyword(s):  
Mechanical Properties ◽  
Shape Memory Alloys ◽  
Shape Memory ◽  
Tensile Tests ◽  
Nitrogen Addition ◽  
Ternary Alloys ◽  
X Ray Diffraction ◽  
Transformation Temperatures ◽  
Arc Melting ◽  
Type Phase

In present paper we will show how nitrogen effects microstructures, transformation temperatures, and mechanical properties of equiatomic Ti50–Ni50 and Ti-rich Ti51–Ni49 binary shape memory alloys. 0.5 at.% of nitrogen was added to prepare Ti50–Ni49.5–N0.5, and Ti51–Ni48.5–N0.5 (at.%) alloys by arc-melting. Microstructures were investigated by scanning electron microscope (SEM), phase constitutions were investigated by X-ray diffraction (XRD), transformation temperatures were investigated by differential scanning calorimeter (DSC) and mechanical properties were tested by tensile tests. Solutions treated Ti–Ni–N shape memory alloys contain TiNi matrix without nitrogen, Ti2Ni type phase containing a small amount of nitrogen and a new Ti2N type phase containing a small amount of nickel. Compared with Ti50–Ni50 and Ti51–Ni49 binary alloys, the martensitic transformation starts temperatures (Ms) of Ti50–Ni49.5–N0.5 and Ti51–Ni48.5–N0.5 ternary alloys decreased from 63.4 °C to 41.6 °C and from 85.3 °C to 79.4 °C, respectively. By adding N, fracture strain decreased and incomplete superelasticity was observed.

Sign in / Sign up

Export Citation Format

Share Document