scholarly journals Influence of Rhamnolipids and Ionic Cross-Linking Conditions on the Mechanical Properties of Alginate Hydrogels as a Model Bacterial Biofilm

2021 ◽  
Vol 22 (13) ◽  
pp. 6840
Author(s):  
Natalia Czaplicka ◽  
Szymon Mania ◽  
Donata Konopacka-Łyskawa
Keyword(s):  
Mechanical Properties ◽  
Pure Water ◽  
Testing Machine ◽  
Bacterial Biofilm ◽  
Ion Trapping ◽  
Cross Linking ◽  
Box Behnken Design ◽  
Compression Load ◽  
Alginate Hydrogels ◽  
Biofilm Structure

The literature indicates the existence of a relationship between rhamnolipids and bacterial biofilm, as well as the ability of selected bacteria to produce rhamnolipids and alginate. However, the influence of biosurfactant molecules on the mechanical properties of biofilms are still not fully understood. The aim of this research is to determine the effect of rhamnolipids concentration, CaCl2 concentration, and ionic cross-linking time on the mechanical properties of alginate hydrogels using a Box–Behnken design. The mechanical properties of cross-linked alginate hydrogels were characterized using a universal testing machine. It was assumed that the addition of rhamnolipids mainly affects the compression load, and the value of this parameter is lower for hydrogels produced with biosurfactant concentration below CMC than for hydrogels obtained in pure water. In contrast, the addition of rhamnolipids in an amount exceeding CMC causes an increase in compression load. In bacterial biofilms, the presence of rhamnolipid molecules does not exceed the CMC value, which may confirm the influence of this biosurfactant on the formation of the biofilm structure. Moreover, rhamnolipids interact with the hydrophobic part of the alginate copolymer chains, and then the hydrophilic groups of adsorbed biosurfactant molecules create additional calcium ion trapping sites.

scholarly journals Study of Ratio Variation of Binary Components of Cross Linking Agent on Extent of Polymerization and Mechanical Properties of Polyurethane Composites

2019 ◽  
Vol 31 (11) ◽  
pp. 2537-2542
Author(s):  
A. Sharma ◽  
S.K. Sharma ◽  
A. Rani
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Testing Machine ◽  
Cross Linking ◽  
Component Ratio ◽  
Polyurethane Composite ◽  
Ratio Variation ◽  
Curing Agents ◽  
Butane Diol ◽  
Trimethylol Propane

Polyethylene glycol based polyurethane polymer and its fly ash reinforced polyurethane composite were prepared by optimizing the concentration ratio of binders, cross linking agents and curing agents. The components ratio of cross linking agents with the same hydroxyl functionalities i.e. 1,4-butane diol and 1,1,1-trimethylol propane affects the mechanical properties of polymer. The extent of polymerization of polyurethane matrix and fly ash reinforced polyurethane composite was found to be independent of the component ratio of cross linking agents. PEG based polyurethane polymer and their fly ash-reinforced composite can be synthesized at particular ratio by mass of cross linking agents i.e. 0.5 keeping constant w/w ratio 3:2 of binders and curing agents. Effect of w/w ratio variation of cross linking agents on the extent of polymerization has been studied through SEM technique. Cross linking agents, curing agents and polyurethane composite have been characterized by IR spectra. Effect of w/w ratio variation of binary components 1,4-butane diol and 1,1,1-trimethylol propane of cross linking agents on the mechanical properties of fly ash-reinforced polyurethane composite has been studied by evaluating tensile strength and Young modulus of composite material by universal testing machine. Hardness of fly ash-reinforced polyurethane composite with different ratio of 1,4-butane diol and 1,1,1-trimethylol propane of cross linking agents was evaluated by durometer

scholarly journals Mechanical Properties of CoCr Dental-Prosthesis Restorations Made by Three Manufacturing Processes. Influence of the Microstructure and Topography

Metals ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 788 ◽  
Author(s):  
Roberto Padrós ◽  
Miquel Punset ◽  
Meritxell Molmeneu ◽  
Aritza Brizuela Velasco ◽  
Mariano Herrero-Climent ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Testing Machine ◽  
Hydraulic Testing ◽  
Laser Sintering ◽  
P Value ◽  
Manufacturing Processes ◽  
Marginal Gap ◽  
Significance Level ◽  
Compression Load ◽  
Significant Difference

The aim of this study is to compare the mechanical properties of three different dental restorations’ manufacturing processes (CADCAM milling, casting and laser sintering) generated by only one laboratory scanner focusing on marginal fit analysis and their mechanical properties. A chrome-cobalt (Cr-Co) alloy from the same batch was used for three different methods to make an implant abutment. This simulates a maxillary right first molar that was fixed in a hemi-maxillary stone model. Five scans were performed by each tested framework. Nine frameworks were manufactured for each manufacture procedure. Field-Emission Scanning Electron Microscope (FE-SEM) direct vision was used to marginal gap measurement in five critical points for each specimen. In order to fix the samples in the microscope chamber, the restorations were submitted at a compression load of 50 N. The samples always have the same orientation and conditions. The resolution of the microscope is 4 nm and it is equipped by J image software. The microstructure of the samples was also determined with the FE-SEM equipped with EDS-microanalysis. Roughness parameters were measured using White Light Interferometry (WLI). The arithmetical mean for the Ra and Rq of each sample was calculated. The samples were mechanically characterized by means of microhardness and flexural testing. Servo-hydraulic testing machine was used with cross-head rate of 1 mm/min. Two-way ANOVA statistical analysis was performed to determine whether the marginal discrepancies and mechanical properties were significantly different between each group (significance level p < 0.05). The overall mean marginal gap values were: from 50.53 ± 10.30 µm for the samples produced by CADCAM to 85.76 ± 22.56 µm for the samples produced by the casting method. Laser sintering presents a marginal gap of 60.95 ± 20.66 µm. The results revealed a statistically significant difference (p-value < 0.005) in the mean marginal gap between the CADCAM systems studied. The higher flexure load to fracture for these restorations were for CADCAM restoration and the lower was for the casting samples. For these restorations, CADCAM Restoration yielded a higher flexure load to fracture and Casting ones yielded the lower. Porosity and microstructure play a very important role in the mechanical properties.

scholarly journals Development of Al–Mg–Si alloy performance by addition of grain refiner Al–5Ti–1B alloy

2021 ◽  
Vol 104 (2) ◽  
pp. 003685042110294
Author(s):  
Khaled Abd El-Aziz ◽  
Emad M Ahmed ◽  
Abdulaziz H Alghtani ◽  
Bassem F Felemban ◽  
Hafiz T Ali ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Corrosion Resistance ◽  
Testing Machine ◽  
Dendritic Structure ◽  
Grain Refiner ◽  
Corrosion Properties ◽  
Average Grain Size ◽  
Structural Applications ◽  
Alloy Addition

Aluminum alloys are the most essential part of all shaped castings manufactured, mainly in the automotive, food industry, and structural applications. There is little consensus as to the precise relationship between grain size after grain refinement and corrosion resistance; conflicting conclusions have been published showing that reduced grain size can decrease or increase corrosion resistance. The effect of Al–5Ti–1B grain refiner (GR alloy) with different percentages on the mechanical properties and corrosion behavior of Aluminum-magnesium-silicon alloy (Al–Mg–Si) was studied. The average grain size is determined according to the E112ASTM standard. The compressive test specimens were made as per ASTM: E8/E8M-16 standard to get their compressive properties. The bulk hardness using Vickers hardness testing machine at a load of 50 g. Electrochemical corrosion tests were carried out in 3.5 % NaCl solution using Autolab Potentiostat/Galvanostat (PGSTAT 30).The grain size of the Al–Mg–Si alloy was reduced from 82 to 46 µm by the addition of GR alloy. The morphology of α-Al dendrites changes from coarse dendritic structure to fine equiaxed grains due to the addition of GR alloy and segregation of Ti, which controls the growth of primary α-Al. In addition, the mechanical properties of the Al–Mg–Si alloy were improved by GR alloy addition. GR alloy addition to Al–Mg–Si alloy produced fine-grained structure and better hardness and compressive strength. The addition of GR alloy did not reveal any marked improvements in the corrosion properties of Al–Mg–Si alloy.

scholarly journals Acoustic Emission and K-S Metric Entropy as Methods for Determining Mechanical Properties of Composite Materials

Sensors ◽  
2020 ◽  
Vol 21 (1) ◽  
pp. 145
Author(s):  
Lesław Kyzioł ◽  
Katarzyna Panasiuk ◽  
Grzegorz Hajdukiewicz ◽  
Krzysztof Dudzik
Keyword(s):  
Mechanical Properties ◽  
Acoustic Emission ◽  
Composite Material ◽  
Composite Materials ◽  
Testing Machine ◽  
Measurement Data ◽  
Entropy Method ◽  
Displacement Sensor ◽  
Metric Entropy ◽  
Plastic Phase

Due to the unique properties of polymer composites, these materials are used in many industries, including shipbuilding (hulls of boats, yachts, motorboats, cutters, ship and cooling doors, pontoons and floats, torpedo tubes and missiles, protective shields, antenna masts, radar shields, and antennas, etc.). Modern measurement methods and tools allow to determine the properties of the composite material, already during its design. The article presents the use of the method of acoustic emission and Kolmogorov-Sinai (K-S) metric entropy to determine the mechanical properties of composites. The tested materials were polyester-glass laminate without additives and with a 10% content of polyester-glass waste. The changes taking place in the composite material during loading were visualized using a piezoelectric sensor used in the acoustic emission method. Thanks to the analysis of the RMS parameter (root mean square of the acoustic emission signal), it is possible to determine the range of stresses at which significant changes occur in the material in terms of its use as a construction material. In the K-S entropy method, an important measuring tool is the extensometer, namely the displacement sensor built into it. The results obtained during the static tensile test with the use of an extensometer allow them to be used to calculate the K-S metric entropy. Many materials, including composite materials, do not have a yield point. In principle, there are no methods for determining the transition of a material from elastic to plastic phase. The authors showed that, with the use of a modern testing machine and very high-quality instrumentation to record measurement data using the Kolmogorov-Sinai (K-S) metric entropy method and the acoustic emission (AE) method, it is possible to determine the material transition from elastic to plastic phase. Determining the yield strength of composite materials is extremely important information when designing a structure.

scholarly journals Formation conditions and mechanical properties of aggregates produced in tephra–water–snow flows

2020 ◽  
Vol 72 (1) ◽  
Author(s):  
Hirofumi Niiya ◽  
Kenichi Oda ◽  
Daisuke Tsuji ◽  
Hiroaki Katsuragi
Keyword(s):  
Mechanical Properties ◽  
Mixing Time ◽  
Testing Machine ◽  
Small Scale ◽  
Scaling Analysis ◽  
Compression Tests ◽  
Ice Slurry ◽  
Experimental Conditions ◽  
Formation Conditions ◽  
Snow And Ice

Abstract The formation of aggregates consisting of snow, water, and tephra has been reported in small-scale experiments on three-phase flows containing tephra, water, and snow, representing lahars triggered by snowmelt. Such aggregates reduce the mobility of mud flow. However, the formation mechanism of such aggregates under various conditions has not been investigated. To elucidate the formation conditions and mechanical properties of the aggregates, we performed mixing experiments with materials on a rotating table and compression tests on the resulting aggregates with a universal testing machine in a low-temperature room at $$0\,^{\circ }\text {C}$$ 0 ∘ C . From experiments with varying component ratios of the mixture and tephra diameter, the following results were obtained: (i) the aggregate grew rapidly and reached maturity after a mixing time of 5 min; (ii) the mass of aggregates increased with snow concentration, exhibiting an approximately linear relationship; (iii) single aggregates with large mass formed at lower and higher tephra concentrations, whereas multiple aggregates with smaller mass were observed at intermediate concentrations; (iv) the shape of the aggregate satisfied the similarity law for an ellipsoid; (v) the compressive mechanical behavior could be modeled by an empirical nonlinear model. The obtained mechanical properties of the aggregates were independent of the experimental conditions; (vi) scaling analysis based on the Reynolds number and the strength of the aggregates showed that the aggregates cannot form in ice-slurry lahars. Our findings suggest that low-speed lahars containing snow and ice are likely to generate aggregates, but snow and ice in the ice-slurry lahars are dispersed without such aggregates.

scholarly journals Hyperbranched polyamide modified graphene oxide-reinforced polyurethane nanocomposites with enhanced mechanical properties

RSC Advances ◽  
2021 ◽  
Vol 11 (24) ◽  
pp. 14484-14494
Author(s):  
Yahao Liu ◽  
Jian Zheng ◽  
Xiao Zhang ◽  
Yongqiang Du ◽  
Guibo Yu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Graphene Oxide ◽  
High Performance ◽  
Cross Linking ◽  
Elongation At Break ◽  
Modified Graphene Oxide ◽  
High Performance Composite ◽  
Modified Graphene ◽  
Polyurethane Nanocomposites ◽  
Hyperbranched Polyamide

We successfully modified graphene oxide with amino-terminated hyperbranched polyamide (HGO), and obtained a high-performance composite with enhanced strength and elongation at break via cross-linking hydroxyl-terminated polybutadiene chains with HGO.

scholarly journals Mechanical Properties of the Composite Material consisting of β-TCP and Alginate-Di-Aldehyde-Gelatin Hydrogel and Its Degradation Behavior

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1303
Author(s):  
Michael Seidenstuecker ◽  
Thomas Schmeichel ◽  
Lucas Ritschl ◽  
Johannes Vinke ◽  
Pia Schilling ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Protein Concentration ◽  
Failure Load ◽  
Testing Machine ◽  
Experimental Period ◽  
Flow Chamber ◽  
Degradation Behavior ◽  
Gelatin Hydrogel ◽  
Universal Testing

This work aimed to determine the influence of two hydrogels (alginate, alginate-di-aldehyde (ADA)/gelatin) on the mechanical strength of microporous ceramics, which have been loaded with these hydrogels. For this purpose, the compressive strength was determined using a Zwick Z005 universal testing machine. In addition, the degradation behavior according to ISO EN 10993-14 in TRIS buffer pH 5.0 and pH 7.4 over 60 days was determined, and its effects on the compressive strength were investigated. The loading was carried out by means of a flow-chamber. The weight of the samples (manufacturer: Robert Mathys Foundation (RMS) and Curasan) in TRIS solutions pH 5 and pH 7 increased within 4 h (mean 48 ± 32 mg) and then remained constant over the experimental period of 60 days. The determination surface roughness showed a decrease in the value for the ceramics incubated in TRIS compared to the untreated ceramics. In addition, an increase in protein concentration in solution was determined for ADA gelatin-loaded ceramics. The macroporous Curasan ceramic exhibited a maximum failure load of 29 ± 9.0 N, whereas the value for the microporous RMS ceramic was 931 ± 223 N. Filling the RMS ceramic with ADA gelatin increased the maximum failure load to 1114 ± 300 N. The Curasan ceramics were too fragile for loading. The maximum failure load decreased for the RMS ceramics to 686.55 ± 170 N by incubation in TRIS pH 7.4 and 651 ± 287 N at pH 5.0.

scholarly journals Smart Hydrogel Bilayers Prepared by Irradiation

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1753
Author(s):  
Weixian Huo ◽  
Heng An ◽  
Shuquan Chang ◽  
Shengsheng Yang ◽  
Yin Huang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Gamma Radiation ◽  
Antibacterial Properties ◽  
Cross Linking ◽  
Temperature Sensitive ◽  
Temperature Changes ◽  
Smart Hydrogel ◽  
Isopropyl Acrylamide ◽  
Hydrogel Synthesis ◽  
Potential Applications

Environment-responsive hydrogel actuators have attracted tremendous attention due to their intriguing properties. Gamma radiation has been considered as a green cross-linking process for hydrogel synthesis, as toxic cross-linking agents and initiators were not required. In this work, chitosan/agar/P(N-isopropyl acrylamide-co-acrylamide) (CS/agar/P(NIPAM-co-AM)) and CS/agar/Montmorillonite (MMT)/PNIPAM temperature-sensitive hydrogel bilayers were synthesized via gamma radiation at room temperature. The mechanical properties and temperature sensitivity of hydrogels under different agar content and irradiation doses were explored. The enhancement of the mechanical properties of the composite hydrogel can be attributed to the presence of agar and MMT. Due to the different temperature sensitivities provided by the two layers of hydrogel, they can move autonomously and act as a flexible gripper as the temperature changes. Thanks to the antibacterial properties of the hydrogel, their storage time and service life may be improved. The as prepared hydrogel bilayers have potential applications in control devices, soft robots, artificial muscles and other fields.

scholarly journals Double-Cross-Linked Networks Based on Methacryloyl Mucin

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1706
Author(s):  
Elena Olăreț ◽  
Brîndușa Bălănucă ◽  
Andra Mihaela Onaș ◽  
Jana Ghițman ◽  
Horia Iovu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aqueous Solution ◽  
Chemical Modification ◽  
Structural Modification ◽  
Aqueous Media ◽  
Cross Linking ◽  
Ph Values ◽  
Acid Aqueous Solution ◽  
Reaction Media ◽  
Double Cross

Mucin is a glycoprotein with proven potential in the biomaterials field, but its use is still underexploited for such applications. The present work aims to produce a synthesis of methacryloyl mucin single-network (SN) hydrogels and their double-cross-linked-network (DCN) counterparts. Following the synthesis of the mucin methacryloyl derivative, various SN hydrogels are prepared through the photopolymerization of methacrylate bonds, using reaction media with different pH values. The SN hydrogels are converted into DCN systems via supplementary cross-linking in tannic acid aqueous solution. The chemical modification of mucin is described, and the obtained product is characterized; the structural modification of mucin is assessed through FTIR spectroscopy, and the circular dichroism and the isoelectric point of methacryloyl mucin is evaluated. The affinity for aqueous media of both SN and DCN hydrogels is estimated, and the mechanical properties of the systems are assessed, both at macroscale through uniaxial compression and rheology tests and also at microscale through nanoindentation tests.

Sign in / Sign up

Export Citation Format

Share Document