scholarly journals Study the Use of Activated Carbon and Bone Char on the Performance of Gravity Sand-Bag Water Filter

Membranes ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 868
Author(s):  
Eric Fung ◽  
Ken I. Johnson ◽  
Wenqi Li ◽  
William Borges ◽  
Kai Chi ◽  
...  
Keyword(s):  
Removal Efficiency ◽  
High Surface ◽  
High Surface Area ◽  
Synergetic Effect ◽  
Freundlich Isotherm ◽  
Surface Characteristics ◽  
Isotherm Models ◽  
Fluoride Removal ◽  
Maximum Adsorption Capacity ◽  
Bag Filter

In this study, granulated activated charcoal (GAC) and bio charcoal (BC) is used as a filler in P3 biosand bag filter to study their filtration performance against a range of fluoride impurities from 1–1400 mg/L. A set of experiments are done to analyze the filtration efficiency of the sandbag filter against fluoride impurities after incorporating different amounts (e.g., 0.2, 2 kg) and a combination of GAC and BC. A combination of filler GAC and BC (1 kg each) have exhibited excellent results with 100% fluoride removal efficiency against 5 mg/L fluoride impurities for an entire experimental time of 165 min. It is because of the synergetic effect of adsorption caused by the high surface area (739 m2/g) of GAC and hydroxyapatite groups in BC. The data from remediation experiments using individual GAC and BC are fitted into the Langmuir and Freundlich Isotherm Models to check their adsorption mechanism and determine GAC and BC’s maximum adsorption capacity (Qm). The remediation data for both GAC and BC have shown the better fitting to the Langmuir Isotherm Model with a high R2 value of 0.994 and 0.970, respectively, showing the excellent conformity with monolayer adsorption. While the GAC and BC have presented negative Kf values of −1.08 and −0.72, respectively, for Freundlich Model, showing the non-conformity to multilayer adsorption. The Qm values obtained from Langmuir Model for GAC is 6.23 mg/g, and for BC, it is 9.13 mg/g. The pH study on adsorption efficiency of individual GAC and BC against 5 mg/L of fluoride impurities indicates the decrease in removal efficiency with an increase in pH from 3 to 9. For example, BC has shown removal efficiency of 99.8% at pH 3 and 99.5% at pH 9, while GAC has exhibited removal efficiency of 96.1% at pH 3 and 95.9% at pH 9. Importantly, this study presents the significance of the synergetic application of GAC and BC in the filters, where GAC and BC are different in their origin, functionalities, and surface characteristics.

scholarly journals Adsorption of Mn2+ from Aqueous Solution Using Manganese Oxide-Coated Hollow Polymethylmethacrylate Microspheres (MHPM)

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Dhiraj Dutta ◽  
Jyoti Prasad Borah ◽  
Amrit Puzari
Keyword(s):  
Aqueous Solution ◽  
Manganese Oxide ◽  
Adsorption Capacity ◽  
High Surface ◽  
High Surface Area ◽  
Freundlich Isotherm ◽  
Ion Concentration ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Coated Sand

Results of investigation on adsorption of Mn2+ from aqueous solution by manganese oxide-coated hollow polymethylmethacrylate microspheres (MHPM) are reported here. This is the first report on Mn-coated hollow polymer as a substitute for widely used materials like green sand or MN-coated sand. Hollow polymethylmethacrylate (HPM) was prepared by using a literature procedure. Manganese oxide (MnO) was coated on the surface of HPM (MHPM) by using the electroless plating technique. The HPM and MHPM were characterized by using optical microscopy (OM), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). Optical and scanning micrographs were used to monitor the surface properties of the coated layer which revealed the presence of MnO on the surface of HPM. TGA showed the presence of 4-5% of MnO in MHPM. Adsorption isotherm studies were carried out as a function of pH, initial ion concentration, and contact time, to determine the adsorption efficiency for removal of Mn2+ from contaminated water by the synthesized MHPM. The isotherm results showed that the maximum adsorption capacity of MnO-coated HPM to remove manganese contaminants from water is 8.373 mg/g. The obtained R 2 values of Langmuir isotherm and Freundlich isotherm models were 1 and 0.87, respectively. Therefore, R 2 magnitude confirmed that the Langmuir model is best suited for Mn2+ adsorption by a monolayer of MHPM adsorbent. The material developed shows higher adsorption capacity even at a higher concentration of solute ions, which is not usually observed with similar materials of this kind. Overall findings indicate that MHPM is a very potential lightweight adsorbent for removal of Mn2+ from the aqueous solution because of its low density and high surface area.

scholarly journals Characterization of Residual Biomasses and Its Application for the Removal of Lead Ions from Aqueous Solution

2019 ◽  
Vol 9 (21) ◽  
pp. 4486 ◽  
Author(s):  
Candelaria Tejada-Tovar ◽  
Angel Darío Gonzalez-Delgado ◽  
Angel Villabona-Ortiz
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
High Surface ◽  
High Surface Area ◽  
Freundlich Isotherm ◽  
Mesoporous Structure ◽  
Isotherm Models ◽  
Solution Ph ◽  
Batch Mode ◽  
Suitable Alternative

The removal of water pollutants has been widely addressed for the conservation of the environment, and novel materials are being developed as adsorbent to address this issue. In this work, different residual biomasses were employed to prepare biosorbents applied to lead (Pb(II)) ion uptake. The choice of cassava peels (CP), banana peels (BP), yam peels (YP), and oil palm bagasse (OPB) was made due to the availability of such biomasses in the Department of Bolivar (Colombia), derived from agro-industrial activities. The materials were characterized by ultimate and proximate analysis, Fourier Transform Infrared Spectroscopy (FTIR), Brunauer-Emmett-Teller analysis (BET), Scanning Electron Microscopy (SEM), and Energy Dispersive X-Ray Spectroscopy (EDS) in order to determine the physicochemical properties of bioadsorbents. The adsorption tests were carried out in batch mode, keeping the initial metal concentration at 100 ppm, temperature at 30 °C, particle size at 1 mm, and solution pH at 6. The experimental results were adjusted to kinetic and isotherm models to determine the adsorption mechanism. The remaining concentration of Pb(II) in solution was measured by atomic absorption at 217 nm. The functional groups identified in FTIR spectra are characteristic of lignocellulosic materials. A high surface area was found for all biomaterials with the exception of yam peels. A low pore volume and size, related to the mesoporous structure of these materials, make these bioadsorbents a suitable alternative for liquid phase adsorption, since they facilitate the diffusion of Pb(II) ions onto the adsorbent structure. Both FTIR and EDS techniques confirmed ion precipitation onto adsorbent materials after the adsorption process. The adsorption tests reported efficiency values above 80% for YP, BP, and CP, indicating a good uptake of Pb(II) ions from aqueous solution. The results reported that Freundlich isotherm and pseudo-second order best fit experimental data, suggesting that the adsorption process is governed by chemical reactions and multilayer uptake. The future prospective of this work lies in the identification of alternatives to reuse Pb(II)-contaminated biomasses after heavy metal adsorption, such as material immobilization.

scholarly journals Self-Nitrogen-Doped Nanoporous Carbons Derived from Poly(1,5-diaminonaphthalene) for the Removal of Toxic Dye Pollutants from Wastewater: Non-Linear Isotherm and Kinetic Analysis

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2563
Author(s):  
Ali Aldalbahi ◽  
Badr M. Thamer ◽  
Mostafizur Rahaman ◽  
Mohamed H. El-Newehy
Keyword(s):  
Surface Area ◽  
High Efficiency ◽  
High Surface ◽  
High Surface Area ◽  
Freundlich Isotherm ◽  
Vital Role ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Nanoporous Carbons ◽  
Nitrogen Doped

The high surface area and porosity of self-nitrogen-doped porous carbons (SNPCs) nominates them for potential application in water treatment due to their high efficiency towards the removal of various pollutants. In this study, SNPCs were fabricated from poly(1,5-diaminonaphthalene) (P(1,5-DANPh) by single and simultaneous carbonization at the activation step at different temperatures (600, 700, and 800 °C). The carbonization’s temperature plays a vital role in controlling the nitrogen-doping, surface area, porosity, and morphology of SNPCs. The SNPCs-7 sample prepared at 700 °C showed the highest surface area (1678.8 m2 g−1) with pore volume (0.943 cm3 g−1) with a micro/meso porous structure. The prepared SNPCs were used as an effective adsorbent for removal of crystal violet dye (CV) from contaminated water. SNPCs-7 showed the highest adsorption of 487.53 mg g−1 and the adsorption capacity of the SNPCs samples follows the order SNPCs-7 > SNPCs-8 > SNPCs-6, which is consistent with the results of their surface area and porosity. The adsorption for CV dye followed Freundlich isotherm models and a pseudo second order kinetic model. The negative values of Gipps free energy (ΔG°) and positive value of enthalpy (ΔH°) indicated that the adsorption of CV dye onto the surface of SNPCs was a spontaneous and endothermic process, respectively. Based on the results, the adsorption mechanism of CV dye onto the surface of SNPCs was proposed.

Effect of the Pore Diameters and Amino-Organo Functional Structures on Mesoporous Silicas for DNA Adsorption

2016 ◽  
Vol 720 ◽  
pp. 31-36 ◽  
Author(s):  
Ryouichi Hikosaka ◽  
Fukue Nagata ◽  
Masahiro Tomita ◽  
Katsuya Kato
Keyword(s):  
Pore Size ◽  
Functional Groups ◽  
High Surface ◽  
High Surface Area ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Surface Functional Groups ◽  
Dna Adsorption ◽  
Equilibrium Data ◽  
Adsorption Equilibrium Data

Deoxyribonucleic acid (DNA) adsorption onto particles has applications in biosensors, separation methods, and gene delivery. Mesoporous silica (MPS), which exhibits a high surface area and large pore volume, is used in these applications because its pore size is easily controlled and its surface functional groups are easily exchanged. In this study, three types of MPSs with different pore sizes (2.4, 5.6, and 11.8 nm) were functionalized with different aminosilane coupling reagents and the effects of the MPS pore size and surface functional groups on DNA adsorption were evaluated. As the pore size of MPS increased, MPSs with diethylenetriamine (–3NH2) adsorbed higher amounts of DNA, whereas MPSs with hexylenediamine groups (–2HNH2) adsorbed lower amounts of DNA. Moreover, the fitting of DNA adsorption equilibrium data to Langmuir and Freundlich isotherm models was investigated.

Activated carbon from molasses efficiency for Cr(VI), Pb(II) and Cu(II) adsorption: A mechanistic study

2019 ◽  
Author(s):  
Chem Int
Keyword(s):  
Activated Carbon ◽  
Phosphoric Acid ◽  
Sugar Industry ◽  
Chemical Activation ◽  
High Surface ◽  
High Surface Area ◽  
Mechanistic Study ◽  
Acid Mixture ◽  
Maximum Adsorption Capacity ◽  
Good Potential

Activated carbon was prepared from molasses, which are natural precursors of vegetable origin resulting from the sugar industry. A simple elaboration process, based on chemical activation with phosphoric acid, was proposed. The final product, prepared by activation of molasses/phosphoric acid mixture in air at 500°C, presented high surface area (more than 1400 m2/g) and important maximum adsorption capacity for methylene blue (625 mg/g) and iodine (1660 mg/g). The activated carbon (MP2(500)) showed a good potential for the adsorption of Cr(VI), Cu(II) and Pb(II) from aqueous solutions. The affinity for the three ions was observed in the following order Cu2+ Cr6+ Pb2+. The process is governed by monolayer adsorption following the Langmuir model, with a correlation coefficient close to unity.

scholarly journals Synthesis of Silver-Impregnated Magnetite Mesoporous Silica Composites for Removing Iodide in Aqueous Solution

Toxics ◽  
2021 ◽  
Vol 9 (8) ◽  
pp. 175
Author(s):  
Sang-Eun Jo ◽  
Jung-Weon Choi ◽  
Sang-June Choi
Keyword(s):  
Aqueous Solution ◽  
Langmuir Isotherm ◽  
High Surface ◽  
High Surface Area ◽  
High Capacity ◽  
Maximum Adsorption Capacity ◽  
Initial Contact ◽  
Order Kinetic ◽  
Sorption Ability ◽  
High Sorption

Mag@silica-Ag composite has a high sorption ability for I− in aqueous solution due to its high surface area and strong affinity for the studied anion. The material adsorbed I− rapidly during the initial contact time (in 45 min, η = 80%) and reached adsorption equilibrium after 2 h. Moreover, mag@silica-Ag proved to selectively remove I− from a mixture of Cl−, NO3− and I−. The adsorption behavior fitted the Langmuir isotherm perfectly and the pseudo-second-order kinetic model. Based on the Langmuir isotherm, the maximum adsorption capacity of mag@silica-Ag was 0.82 mmol/g, which is significantly higher than previously developed adsorbents. This study introduces a practical application of a high-capacity adsorbent in removing radioactive I− from wastewaters.

scholarly journals A new biocompatible ternary Layered Double Hydroxide Adsorbent for ultrafast removal of anionic organic dyes

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Garima Rathee ◽  
Amardeep Awasthi ◽  
Damini Sood ◽  
Ravi Tomar ◽  
Vartika Tomar ◽  
...  
Keyword(s):  
Waste Water ◽  
Methyl Orange ◽  
Surface Area ◽  
Layered Double Hydroxide ◽  
Removal Efficiency ◽  
Organic Dyes ◽  
High Surface ◽  
High Surface Area ◽  
Morphological Studies ◽  
Double Hydroxide

Abstract It would be of great significance to introduce a new biocompatible Layered Double Hydroxide (LDH) for the efficient remediation of wastewater. Herein, we designed a facile, biocompatible and environmental friendly layered double hydroxide (LDH) of NiFeTi for the very first time by the hydrothermal route. The materialization of NiFeTi LDH was confirmed by FTIR, XRD and Raman studies. BET results revealed the high surface area (106 m2/g) and the morphological studies (FESEM and TEM) portrayed the sheets-like structure of NiFeTi nanoparticles. The material so obtained was employed as an efficient adsorbent for the removal of organic dyes from synthetic waste water. The dye removal study showed >96% efficiency for the removal of methyl orange, congo red, methyl blue and orange G, which revealed the superiority of material for decontamination of waste water. The maximum removal (90%) of dyes was attained within 2 min of initiation of the adsorption process which supported the ultrafast removal efficiency. This ultrafast removal efficiency was attributed to high surface area and large concentration of -OH and CO32− groups present in NiFeTi LDH. In addition, the reusability was also performed up to three cycles with 96, 90 and 88% efficiency for methyl orange. Furthermore, the biocompatibility test on MHS cell lines were also carried which revealed the non-toxic nature of NiFeTi LDH at lower concentration (100% cell viability at 15.6 μg/ml). Overall, we offer a facile surfactant free method for the synthesis of NiFeTi LDH which is efficient for decontamination of anionic dyes from water and also non-toxic.

Biosorption of Cadmium onto Pseudomonas fluorescens: Application of Isotherm and Kinetic Models

2010 ◽  
Vol 171-172 ◽  
pp. 49-52 ◽  
Author(s):  
Chang Li Yu ◽  
Zhi Peng Lu ◽  
Fa Zhi Ge ◽  
Er Li Zhao
Keyword(s):  
Pseudomonas Fluorescens ◽  
Functional Groups ◽  
Metal Ion ◽  
Freundlich Isotherm ◽  
Industrial Effluents ◽  
Rate Equations ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Kinetics Of Adsorption ◽  
Isotherm And Kinetic Models

The present study was undertaken to evaluate the feasibility of Pseudomonas fluorescens biomass for the removal of cadmium ions from aqueous solutions. Batch experiments were performed to study the adsorption of cadmium on pH, Pseudomonas fluorescens biomass adsorbent with respect to initial Cd(II) concentration, contact time and biomass dose. The experimental data were modeled by Langmuir and Freundlich isotherm models. Langmuir model resulted in the best fit of the adsorption data. The maximum adsorption capacity for Cd(II) was 66.25 mg/g (pH 5.0 and 5 g/L biomass dose). Kinetics of adsorption followed second-order rate equations. The FTIR results of Pseudomonas fluorescens biomass showed that biomass has different functional groups and these functional groups are able to react with metal ion in aqueous solution. The results of the present study suggest that Pseudomonas fluorescens biomass can be used beneficially in treating industrial effluents containing heavy metal ions.

scholarly journals Phenol adsorption from wastewater using cashew nut shells as adsorbent

2018 ◽  
Vol 7 (3) ◽  
pp. 966
Author(s):  
Kartik Kulkarni ◽  
Varsha Sudheer ◽  
C R Girish
Keyword(s):  
Agricultural Waste ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Multilayer Adsorption ◽  
Phenol Adsorption ◽  
Cashew Nut ◽  
Experimental Parameters ◽  
Order Kinetic Model

The potential of agricultural waste cashew nut shells as an adsorbent for removing phenol from wastewater is presented in this paper. The adsorbent was treated with 3M sulphuric acid in order to improve the properties. The experimental parameters such as adsorbent dosage, concentration and temperature were optimized with response surface methodology (RSM). The isotherm data were tested with different isotherm models and it obeyed Freundlich Isotherm showing the multilayer adsorption. The kinetic data satisfied pseudo-first order kinetic model. The maximum adsorption capacity was calculated to be 35.08 mg/g proving the capability of cashew nut shells for removing phenol from wastewater.  

Synthesis and Application of Zn‑BTC/GO Nanocomposites as Highly Efficient Photocatalysts in the Dye Degradation

2021 ◽  
Vol 11 (1) ◽  
pp. 67-73
Author(s):  
Manh Nguyen Ba ◽  
Trang Pham Thi Thu ◽  
Hoa Tran Thi ◽  
Giang Le Ha
Keyword(s):  
Removal Efficiency ◽  
Dye Degradation ◽  
High Surface ◽  
High Surface Area ◽  
Reactive Dye ◽  
High Photocatalytic Activity ◽  
Microwave Method ◽  
Sem Image ◽  
High Initial Concentration ◽  
Reactive Red 195

Nanocomposite Zn-BTC/GO (BTC: benzene-1,3,5-tricarboxylic, GO: graphene oxide) was successfully synthesized by hydrothermal treatment with a microwave method. Samples were characterized by XRD, FTIR, EDS-mapping, BET, SEM, UV-vis DRS and XPS. SEM-image result showed nano Zn-BTC/GO particles size of 50-80 nm. Nanocomposite Zn-BTC/GO showed the a high surface area (1303 m2/g) and pore volume (1.08 cm3/g). The Zn-BTC/GO nanocomposite were tested for the photocatalytic degradation of reactive dye (Reactive Red 195) in an aqueous solution. The Zn-BTC/GO composites exhibited high photocatalytic activity. Thus, at the pH of 6.5 and the high initial concentration of 30 mg RR-195/L, removal efficiency reached the value of 96.16% after 60 min reaction. Moreover, nano Zn-BTC also showed high RR-195 removal efficiency after 3 catalytic regeneration. This contributes to sustainable development and green chemistry.

Sign in / Sign up

Export Citation Format

Share Document