scholarly journals The Effect of Accelerated Aging on Polylactide Containing Plant Extracts

Polymers ◽  
2019 ◽  
Vol 11 (4) ◽  
pp. 575 ◽  
Author(s):  
Krzysztof Moraczewski ◽  
Magdalena Stepczyńska ◽  
Rafał Malinowski ◽  
Tomasz Karasiewicz ◽  
Bartłomiej Jagodziński ◽  
...  
Keyword(s):  
Aging Process ◽  
Accelerated Aging ◽  
Tensile Tests ◽  
Butylated Hydroxytoluene ◽  
Plant Origin ◽  
Reference Compound ◽  
Scanning Calorimetry ◽  
Visual Evaluation ◽  
Melt Flow Rate ◽  
Natural Extracts

In this study, natural extracts of plant origin were used as anti-aging compounds of biodegradable polymers. Coffee (0.5–10 wt%), cocoa, or cinnamon extracts were added to the polylactide matrix. The obtained materials were subjected to an accelerated aging process (720, 1440, or 2160 h) at 45 °C and 70% relative humidity under continuous UV radiation. The effectiveness of the tested extracts was compared to a commercially available anti-aging compound, 2 wt% of butylated hydroxytoluene. Visual evaluation, scanning electron microscopy, melt flow rate, thermogravimetry, differential scanning calorimetry, tensile strength, and impact tensile tests were performed. We show that the use of smaller amounts of tested extracts is particularly advantageous, which do not adversely affect the properties of polylactide-based materials at low contents. At the same time, their effectiveness in stabilizing tested properties during the accelerated aging process is mostly comparable to or greater than the reference compound.

scholarly journals Physical Property Changes in Plutonium Observed from Accelerated Aging using Pu-238 Enrichment

2006 ◽  
Vol 986 ◽  
Author(s):  
Brandon W. Chung ◽  
Bill Choi ◽  
Cheng Saw ◽  
Stephen Thompson ◽  
Conrad Woods ◽  
...  
Keyword(s):  
Ultimate Strength ◽  
Tensile Property ◽  
Aging Process ◽  
Accelerated Aging ◽  
Physical Property ◽  
Tensile Tests ◽  
Weight Percent ◽  
Volume Increase ◽  
Property Changes ◽  
Weapons Grade Plutonium

AbstractWe present changes in volume, immersion density, and tensile property observed from accelerated aged plutonium alloys. Accelerated alloys (or spiked alloys) are plutonium alloys enriched with approximately 7.5 weight percent of the faster-decaying 238Pu to accelerate the aging process by approximately 17 times the rate of unaged weapons-grade plutonium. After sixty equivalent years of aging on spiked alloys, the dilatometry shows the samples at 35°C have swelled in volume by 0.15 to 0.17 % and now exhibit a near linear volume increase due to helium in-growth. The immersion density of spiked alloys shows decrease in density, similar normalized volumetric changes (expansion) for spiked alloys. Tensile tests show increasing yield and engineering ultimate strength as spiked alloys are aged.

Thermal Properties of Poly(Lactic Acid) Modified Poly(3-Hydroxybutyrate-co-4-Hydroxbutyrate)

2016 ◽  
Vol 852 ◽  
pp. 677-685
Author(s):  
Mei Li ◽  
Zhi Qiang Li ◽  
Wei Shao
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Thermal Properties ◽  
Tensile Tests ◽  
Poly Lactic Acid ◽  
Flow Properties ◽  
Scanning Calorimetry ◽  
Melt Flow Rate ◽  
Elongation At Break ◽  
Good Flow

The thermal properties of poly (lactic acid)[PLA] modified poly (3 –hydroxybutyrate –co-4 -hydroxbutyrate) [P(3HB-co-4HB)], prepared by melt blending with different blending ratios were investigated by differential scanning calorimetry [DSC], thermogravimetry [TGA], melt flow rate [MFR] and tensile test measurements, and scanning electron microscopy [SEM]. The DSC tests showed that the glass transition temperature, Tg, of P(3HB-co-4HB) increased from-7°C to 56°C when mixed with 50% to 67% of PLA. A decrease in crystallization temperature, Tc, of P(3HB-co-4HB) broadened the melting interval. The MFR tests indicated the blends had good flow properties and the variation of the PLA content had little effect on the flow properties. The tensile tests showed that PLA improved the mechanical properties of P(3HB-co-4HB), including the tensile strength and elongation at break. The blends had the best mechanical properties when the percentage of PLA was 64%.

scholarly journals Wastes from Agricultural Silage Film Recycling Line as a Potential Polymer Materials

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1383
Author(s):  
Jerzy Korol ◽  
Aleksander Hejna ◽  
Klaudiusz Wypiór ◽  
Krzysztof Mijalski ◽  
Ewelina Chmielnicka
Keyword(s):  
Vinyl Acetate ◽  
Thermal Performance ◽  
Mechanical Performance ◽  
Ethylene Vinyl Acetate ◽  
Tensile Tests ◽  
Solid Particles ◽  
Polymer Materials ◽  
Slight Reduction ◽  
Scanning Calorimetry ◽  
Crystallinity Degree

The recycling of plastics is currently one of the most significant industrial challenges. Due to the enormous amounts of plastic wastes generated by various industry branches, it is essential to look for potential methods for their utilization. In the presented work, we investigated the recycling potential of wastes originated from the agricultural films recycling line. Their structure and properties were analyzed, and they were modified with 2.5 wt % of commercially available compatibilizers. The mechanical and thermal performance of modified wastes were evaluated by tensile tests, thermogravimetric analysis, and differential scanning calorimetry. It was found that incorporation of such a small amount of modifiers may overcome the drawbacks caused by the presence of impurities. The incorporation of maleic anhydride-grafted compounds enhanced the tensile strength of wastes by 13–25%. The use of more ductile compatibilizers—ethylene-vinyl acetate and paraffin increased the elongation at break by 55–64%. The presence of compatibilizers also reduced the stiffness of materials resulting from the presence of solid particles. It was particularly emphasized for styrene-ethylene-butadiene-styrene and ethylene-vinyl acetate copolymers, which caused up to a 20% drop of Young’s modulus. Such effects may facilitate the further applications of analyzed wastes, e.g., in polymer film production. Thermal performance was only slightly affected by compatibilization. It caused a slight reduction in polyethylene melting temperatures (up to 2.8 °C) and crystallinity degree (up to 16%). For more contaminated materials, the addition of compatibilizers caused a minor reduction in the decomposition onset (up to 6 °C). At the same time, for the waste after three washing cycles, thermal stability was improved. Moreover, depending on the desired properties and application, materials do not have to go through the whole recycling line, simplifying the process, reducing energy and water consumption. The presented results indicate that it is possible to efficiently use the materials, which do not have to undergo the whole recycling process. Despite the presence of impurities, they could be applied in the manufacturing of products which do not require exceptional mechanical performance.

scholarly journals Characterization of Beeswax, Candelilla Wax and Paraffin Wax for Coating Cheeses

Coatings ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 261
Author(s):  
Adolfo Bucio ◽  
Rosario Moreno-Tovar ◽  
Lauro Bucio ◽  
Jessica Espinosa-Dávila ◽  
Francisco Anguebes-Franceschi
Keyword(s):  
Physical And Mechanical Properties ◽  
Tensile Tests ◽  
Paraffin Wax ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Absorption Bands ◽  
Dimensional Changes ◽  
Ductile Behavior ◽  
Candelilla Wax

A study on the physical and mechanical properties of beeswax (BW), candelilla wax (CW), paraffin wax (PW) and blends was carried out with the aim to evaluate their usefulness as coatings for cheeses. Waxes were analyzed by X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), differential scanning calorimetry (DSC), permeability, viscosity, flexural and tensile tests and scanning electron microscopy. Cheeses were coated with the waxes and stored for 5 weeks at 30 °C. Measured parameters were weight, moisture, occurrence and degree of fractures, and dimensional changes. The crystal phases identified by XRD for the three waxes allowed them to determine the length of alkanes and the nonlinear compounds in crystallizable forms in waxes. FTIR spectra showed absorption bands between 1800 and 800 cm−1 related to carbonyls in BW and CW. In DSC, the onset of melting temperature was 45.5 °C for BW, and >54 °C for CW and PW. Cheeses coated with BW did not show cracks after storage. Cheeses coated with CW and PW showed microcraks, and lost weight, moisture and shrunk. In the flexural and tensile tests, BW was ductile; CW and PW were brittle. BW blends with CW or PW displays a semi ductile behavior. Cheeses coated with BW blends lost less than 5% weight during storage. The best waxes were BW and the blends.

scholarly journals Recycling Potential for Non-Valorized Plastic Fractions from Electrical and Electronic Waste

Recycling ◽  
2021 ◽  
Vol 6 (2) ◽  
pp. 33
Author(s):  
Laura Strobl ◽  
Thomas Diefenhardt ◽  
Martin Schlummer ◽  
Tanja Leege ◽  
Swetlana Wagner
Keyword(s):  
Flame Retardants ◽  
Electronic Waste ◽  
Gel Permeation Chromatography ◽  
Scanning Calorimetry ◽  
Separation Processes ◽  
Melt Flow Rate ◽  
Density Fractions ◽  
Material Recycling ◽  
Other Substances ◽  
Electrical And Electronic Waste

This paper describes a study for waste of electrical and electronic equipment (WEEE) to characterise the plastic composition of different mixed plastic fractions. Most of the samples studied are currently excluded from material recycling and arise as side streams in state-of-the-art plastics recycling plants. These samples contain brominated flame retardants (BFR) or other substances of concern listed as persistent organic pollutants or in the RoHS directive. Seventeen samples, including cathode ray tube (CRT) monitors, CRT televisions, flat screens such as liquid crystal displays, small domestic appliances, and information and communication technology, were investigated using density- and dissolution-based separation processes. The total bromine and chlorine contents of the samples were determined by X-ray fluorescence spectroscopy, indicating a substantial concentration of both elements in density fractions above 1.1 g/cm3, most significantly in specific solubility classes referring to ABS and PS. This was further supported by specific flame retardant analysis. It was shown that BFR levels of both polymers can be reduced to levels below 1000 ppm by dissolution and precipitation processes enabling material recycling in compliance with current legislation. As additional target polymers PC and PC-ABS were also recycled by dissolution but did not require an elimination of BFR. Finally, physicochemical investigations of recycled materials as gel permeation chromatography, melt flow rate, and differential scanning calorimetry suggest a high purity and indicate no degradation of the technical properties of the recycled polymers.

scholarly journals Metallization of Thermoplastic Polymers and Composites 3D Printed by Fused Filament Fabrication

Technologies ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 49
Author(s):  
Alessia Romani ◽  
Andrea Mantelli ◽  
Paolo Tralli ◽  
Stefano Turri ◽  
Marinella Levi ◽  
...  
Keyword(s):  
Physical Vapor Deposition ◽  
Test Sample ◽  
Tensile Tests ◽  
Layer By Layer ◽  
Post Processing ◽  
Thermoplastic Polymers ◽  
Fused Filament Fabrication ◽  
Scanning Calorimetry ◽  
3D Printed ◽  
Manufacturing Technologies

Fused filament fabrication allows the direct manufacturing of customized and complex products although the layer-by-layer appearance of this process strongly affects the surface quality of the final parts. In recent years, an increasing number of post-processing treatments has been developed for the most used materials. Contrarily to other additive manufacturing technologies, metallization is not a common surface treatment for this process despite the increasing range of high-performing 3D printable materials. The objective of this work is to explore the use of physical vapor deposition sputtering for the chromium metallization of thermoplastic polymers and composites obtained by fused filament fabrication. The thermal and mechanical properties of five materials were firstly evaluated by means of differential scanning calorimetry and tensile tests. Meanwhile, a specific finishing torture test sample was designed and 3D printed to perform the metallization process and evaluate the finishing on different geometrical features. Furthermore, the roughness of the samples was measured before and after the metallization, and a cost analysis was performed to assess the cost-efficiency. To sum up, the metallization of five samples made with different materials was successfully achieved. Although some 3D printing defects worsened after the post-processing treatment, good homogeneity on the finest details was reached. These promising results may encourage further experimentations as well as the development of new applications, i.e., for the automotive and furniture fields.

scholarly journals Mechanical, Thermal and Rheological Properties of Polyethylene-Based Composites Filled with Micrometric Aluminum Powder

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1242
Author(s):  
Olga Mysiukiewicz ◽  
Paulina Kosmela ◽  
Mateusz Barczewski ◽  
Aleksander Hejna
Keyword(s):  
Mechanical Properties ◽  
Melt Flow Index ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Flow Index ◽  
Scanning Calorimetry ◽  
Metal Composites ◽  
Pre Treatment ◽  
The Impact ◽  
Properties Of Composites

Investigations related to polymer/metal composites are often limited to the analysis of the electrical and thermal conductivity of the materials. The presented study aims to analyze the impact of aluminum (Al) filler content (from 1 to 20 wt%) on the rarely investigated properties of composites based on the high-density polyethylene (HDPE) matrix. The crystalline structure, rheological (melt flow index and oscillatory rheometry), thermal (differential scanning calorimetry), as well as static (tensile tests, hardness, rebound resilience) and dynamic (dynamical mechanical analysis) mechanical properties of composites were investigated. The incorporation of 1 and 2 wt% of aluminum filler resulted in small enhancements of mechanical properties, while loadings of 5 and 10 wt% provided materials with a similar performance to neat HDPE. Such results were supported by the lack of disturbances in the rheological behavior of composites. The presented results indicate that a significant content of aluminum filler may be introduced into the HDPE matrix without additional pre-treatment and does not cause the deterioration of composites’ performance, which should be considered beneficial when engineering PE/metal composites.

Effects on the microstructure and mechanical properties of Sn-0.7Cu lead-free solder with the addition of a small amount of magnesium

2016 ◽  
Vol 23 (6) ◽  
pp. 641-647
Author(s):  
Her-Yueh Huang ◽  
Chung-Wei Yang ◽  
Yu-Chang Peng
Keyword(s):  
Mechanical Properties ◽  
Aging Process ◽  
Intermetallic Layer ◽  
Eutectic Structure ◽  
Contact Angles ◽  
Solidification Structure ◽  
Lead Free Solder ◽  
Bulk Alloy ◽  
Scanning Calorimetry ◽  
Free Solder

AbstractThe influence of a small amount of magnesium (only 0.01 wt.%) added to the Sn-0.7Cu solder alloy during the aging process of microstructural evolution is studied along with the mechanical properties of the alloy. The experimental results indicate that the addition of magnesium decreases the tensile strength of the solders but improves their elongation. The solidification structure of eutectic Sn-0.7Cu consists of β-Sn, and the eutectic structure, which has extremely fine intermetallic nodules, Cu6Sn5, is located in the interdendritic region. When the magnesium is added to the Sn-0.7Cu alloy, the Sn dendrites become slightly coarser; in comparison, the melting point of the Sn-0.7Cu-0.01Mg alloy decreased by 2°C for the differential scanning calorimetry results of bulk alloy samples. Sn-0.7Cu-0.01Mg exhibits the lowest contact angles and the widest spreading areas. After aging, the Sn-0.7Cu and Sn-0.7Cu-0.01Mg solders show significant changes in strength, mainly because of the obvious increase in the thickness of the Cu6Sn5 intermetallic layer.

scholarly journals Post-Processing Time Dependence of Shrinkage and Mechanical Properties of Injection-Molded Polypropylene

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 22
Author(s):  
Artur Kościuszko ◽  
Dawid Marciniak ◽  
Dariusz Sykutera
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Injection Molding ◽  
Accelerated Aging ◽  
Mold Temperature ◽  
Degree Of Crystallinity ◽  
Injection Mold ◽  
Secondary Crystallization ◽  
Scanning Calorimetry ◽  
Injection Molded

Dimensions of the injection-molded semi-crystalline materials (polymeric products) decrease with the time that elapses from their formation. The post-molding shrinkage is an effect of secondary crystallization; the increase in the degree of polymer crystallinity leads to an increase in stiffness and decrease in impact strength of the polymer material. The aim of this study was to assess the changes in the values of post-molding shrinkage of polypropylene produced by injection molding at two different temperatures of the mold (20 °C and 80 °C), and conditioned for 504 h at 23 °C. Subsequently, the samples were annealed for 24 h at 140 °C in order to conduct their accelerated aging. The results of shrinkage tests were related to the changes of mechanical properties that accompany the secondary crystallization. The degree of crystallinity of the conditioned samples was determined by means of density measurements and differential scanning calorimetry. It was found that the changes in the length of the moldings that took place after removal from the injection mold were accompanied by an increase of 20% in the modulus of elasticity, regardless of the conditions under which the samples were made. The differences in the shrinkage and mechanical properties of the samples resulting from mold temperature, as determined by tensile test, were removed by annealing. However, the samples made at two different injection mold temperature values still significantly differed in impact strength, the values of which were clearly higher for the annealed samples compared to the results determined for the samples immediately after the injection molding.

Enhancing the Thermal and Mechanical Characteristics of Polyvinyl Alcohol (PVA)-Hemp Protein Particles (HPP) Composites

2021 ◽  
Vol 36 (2) ◽  
pp. 137-143
Author(s):  
S. A. Awad
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperatures ◽  
Composite Films ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Decomposition Temperature ◽  
Scanning Calorimetry ◽  
Solution Casting Method ◽  
Protein Particles

Abstract This paper aims to describe the thermal, mechanical, and surface properties of a PVA/HPP blend whereby the film was prepared using a solution casting method. The improvements in thermal and mechanical properties of HPP-based PVA composites were investigated. The characterization of pure PVA and PVA composite films included tensile tests, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The results of TGA and DSC indicated that the addition of HPP increased the thermal decomposition temperature of the composites. Mechanical properties are significantly improved in PVA/HPP composites. The thermal stability of the PVA composite increased with the increase of HPP filler content. The tensile strength increased from 15.74 ± 0.72 MPa to 27.54 ± 0.45 MPa and the Young’s modulus increased from 282.51 ± 20.56 MPa to 988.69 ± 42.64 MPa for the 12 wt% HPP doped sample. Dynamic mechanical analysis (DMA) revealed that at elevated temperatures, enhanced mechanical properties because of the presence of HPP was even more noticeable. Morphological observations displayed no signs of agglomeration of HPP fillers even in composites with high HPP loading.

Sign in / Sign up

Export Citation Format

Share Document