scholarly journals Evaluation of physicochemical and mechanical properties of polymeric formulations for use in the oral cavity

2013 ◽  
Vol 26 (3) ◽  
pp. 252-257
Keyword(s):  
Mechanical Properties ◽  
Oral Cavity ◽  
Mechanical Characteristics ◽  
Cross Linking ◽  
Distilled Water ◽  
Natural Polymer ◽  
Dental Implantation ◽  
Microcrystalline Chitosan ◽  
Medicinal Substances ◽  
Main Material

The aim of this research was to create and investigate a formulation that could be placed within post-extraction alveolus. The main material used in this work is a natural polymer, known as microcrystalline chitosan (MCCh). It was formulated as an aqueous hydrogel with the addition of the cross-linking agent (CaCl2) and various plasticizers (propylene glycol, glycerol and sorbitol). The swelling of the preparations was tested by three different methods under completely different acceptor fluids such as distilled water, phosphate buffer and simulated saliva. The pH was measured on the surfaces of each formulation, as well as the pH of the acceptor fluids; evidently, both of them had a similar pH to that of the oral cavity. Additionally, mechanical properties of the tested materials such as hardness, springiness and cohesiveness were evaluated. Based on research, the best compositions of materials were chosen to obtain preparations of the desired geometry and mechanical characteristics. The results from the study are able to prove that MCCh not only creates a neutral environment within the oral cavity but also, due to its significant absorptive properties, can reduce exu date and po ten tially be considered as a new carrier for medicinal substances used in dental implantation and management.

Dissolution and Mechanical Properties of Sintered Hydroxyapatite Immersed in Water

2006 ◽  
Vol 317-318 ◽  
pp. 789-792 ◽  
Author(s):  
Dong Seok Seo ◽  
Hwan Kim ◽  
Kyu Hong Hwang ◽  
Jong Kook Lee
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Weight Loss ◽  
Grain Boundaries ◽  
Mechanical Characteristics ◽  
Surface Damage ◽  
Distilled Water ◽  
Moisture Protection ◽  
Powder Compacts

Dissolution of hydroxyapatite (HAp) in distilled water and related mechanical properties were investigated. The commercially obtained stoichiometric HAp powders were used as starting materials. After preparing powder compacts, the disks were sintered at 1200oC for 2 h in air with under moisture protection. The sintered specimens were then placed into 40 ml of 7.4 distilled water. After immersing for certain period of time at 37oC, weight loss, microstructure, and mechanical characteristics of the specimens were investigated. Fracture toughnesses were measured for both sintered and immersed HAp for comparison. Evidence for the surface damage was observed with appearance of micron-level of pitting and grain boundaries dissolved. The value for fracture toughness decreased due to dissolution of the materials.

Weldability - Behavior of Welded Reinforcement

2019 ◽  
Vol 70 (10) ◽  
pp. 3469-3472
Keyword(s):  
Mechanical Properties ◽  
Chemical Composition ◽  
Mechanical Characteristics ◽  
Mechanical Performance ◽  
Current Work ◽  
Carbon Equivalent ◽  
Work Process ◽  
Ultimate Limit

Weldability involves two aspects: welding behavior of components and safety in operation. The two aspects will be reduced to the mechanical characteristics of the elements and to the chemical composition. In the case of steel reinforcing rebar’s, it is reduces to the percentage of Cech(carbon equivalent) and to the mechanical characteristics: the yielding limit, the ultimate limit, and the elongations which after that represent the ductility class in which the re-bars is framed. The paper will present some types of steel reinforcing rebar’s with its mechanical characteristics and the welding behavior of those elements. In the current work, process-related behavior of welded reinforcement, joint local and global mechanical properties, and their correlation with behavior of normal reinforcement and also the mechanical performance resulted in this type of joints. Keywords: welding behavior, ultimate limit, reinforcing rebar’s

scholarly journals Dental Applications of Carbon Nanotubes

Molecules ◽  
2021 ◽  
Vol 26 (15) ◽  
pp. 4423
Author(s):  
Marco A. Castro-Rojas ◽  
Yadira I. Vega-Cantu ◽  
Geoffrey A. Cordell ◽  
Aida Rodriguez-Garcia
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Oral Cavity ◽  
Current Status ◽  
Glass Ionomer ◽  
Oral Infections ◽  
Functional Behavior ◽  
The Status ◽  
Comprehensive Survey ◽  
Dental Applications

Glass ionomer cements and resin-based composites are promising materials in restorative dentistry. However, their limited mechanical properties and the risk of bulk/marginal fracture compromise their lifespan. Intensive research has been conducted to understand and develop new materials that can mimic the functional behavior of the oral cavity. Nanotechnological approaches have emerged to treat oral infections and become a part of scaffolds for tissue regeneration. Carbon nanotubes are promising materials to create multifunctional platforms for dental applications. This review provides a comprehensive survey of and information on the status of this state-of-the-art technology and describes the development of glass ionomers reinforced with carbon nanotubes possessing improved mechanical properties. The applications of carbon nanotubes in drug delivery and tissue engineering for healing infections and lesions of the oral cavity are also described. The review concludes with a summary of the current status and presents a vision of future applications of carbon nanotubes in the practice of dentistry.

scholarly journals Mimicking the Mechanical Properties of Aortic Tissue with Pattern-Embedded 3D Printing for a Realistic Phantom

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 5042
Author(s):  
Jaeyoung Kwon ◽  
Junhyeok Ock ◽  
Namkug Kim
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
3D Printing ◽  
Mechanical Characteristics ◽  
Aortic Wall ◽  
Tensile Tests ◽  
Human Aorta ◽  
Aortic Tissue ◽  
Medical Field ◽  
Base Materials

3D printing technology has been extensively applied in the medical field, but the ability to replicate tissues that experience significant loads and undergo substantial deformation, such as the aorta, remains elusive. Therefore, this study proposed a method to imitate the mechanical characteristics of the aortic wall by 3D printing embedded patterns and combining two materials with different physical properties. First, we determined the mechanical properties of the selected base materials (Agilus and Dragonskin 30) and pattern materials (VeroCyan and TPU 95A) and performed tensile testing. Three patterns were designed and embedded in printed Agilus–VeroCyan and Dragonskin 30–TPU 95A specimens. Tensile tests were then performed on the printed specimens, and the stress-strain curves were evaluated. The samples with one of the two tested orthotropic patterns exceeded the tensile strength and strain properties of a human aorta. Specifically, a tensile strength of 2.15 ± 0.15 MPa and strain at breaking of 3.18 ± 0.05 mm/mm were measured in the study; the human aorta is considered to have tensile strength and strain at breaking of 2.0–3.0 MPa and 2.0–2.3 mm/mm, respectively. These findings indicate the potential for developing more representative aortic phantoms based on the approach in this study.

scholarly journals Influence of Rhamnolipids and Ionic Cross-Linking Conditions on the Mechanical Properties of Alginate Hydrogels as a Model Bacterial Biofilm

2021 ◽  
Vol 22 (13) ◽  
pp. 6840
Author(s):  
Natalia Czaplicka ◽  
Szymon Mania ◽  
Donata Konopacka-Łyskawa
Keyword(s):  
Mechanical Properties ◽  
Pure Water ◽  
Testing Machine ◽  
Bacterial Biofilm ◽  
Ion Trapping ◽  
Cross Linking ◽  
Box Behnken Design ◽  
Compression Load ◽  
Alginate Hydrogels ◽  
Biofilm Structure

The literature indicates the existence of a relationship between rhamnolipids and bacterial biofilm, as well as the ability of selected bacteria to produce rhamnolipids and alginate. However, the influence of biosurfactant molecules on the mechanical properties of biofilms are still not fully understood. The aim of this research is to determine the effect of rhamnolipids concentration, CaCl2 concentration, and ionic cross-linking time on the mechanical properties of alginate hydrogels using a Box–Behnken design. The mechanical properties of cross-linked alginate hydrogels were characterized using a universal testing machine. It was assumed that the addition of rhamnolipids mainly affects the compression load, and the value of this parameter is lower for hydrogels produced with biosurfactant concentration below CMC than for hydrogels obtained in pure water. In contrast, the addition of rhamnolipids in an amount exceeding CMC causes an increase in compression load. In bacterial biofilms, the presence of rhamnolipid molecules does not exceed the CMC value, which may confirm the influence of this biosurfactant on the formation of the biofilm structure. Moreover, rhamnolipids interact with the hydrophobic part of the alginate copolymer chains, and then the hydrophilic groups of adsorbed biosurfactant molecules create additional calcium ion trapping sites.

scholarly journals Electromagnetic Interference Shielding and Physical-Mechanical Characteristics of Rubber Composites Filled with Manganese-Zinc Ferrite and Carbon Black

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 616
Author(s):  
Ján Kruželák ◽  
Andrea Kvasničáková ◽  
Klaudia Hložeková ◽  
Rastislav Dosoudil ◽  
Marek Gořalík ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Black ◽  
Zinc Ferrite ◽  
Mechanical Characteristics ◽  
Hybrid Composites ◽  
Rubber Matrix ◽  
Butadiene Rubber ◽  
Frequency Range ◽  
Manganese Zinc ◽  
Manganese Zinc Ferrite

In the present work, composite materials were prepared by incorporation of manganese-zinc ferrite, carbon black and combination of ferrite and carbon black into acrylonitrile-butadiene rubber (NBR). For cross-linking of composites, standard sulfur-based curing system was applied. The main goal was to investigate the influence of the fillers on the physical-mechanical properties of composites. Then, the electromagnetic absorption shielding ability was investigated in the frequency range 1 MHz–3 GHz. The results revealed that composites filled with ferrite provide sufficient absorption shielding performance in the tested frequency range. On the other hand, ferrite behaves as an inactive filler and deteriorates the physical-mechanical characteristics of composites. Carbon black reinforces the rubber matrix and contributes to the improvement of physical-mechanical properties. However, composites filled with carbon black are not able to absorb electromagnetic radiation in the given frequency range. Finally, the combination of carbon black and ferrite resulted in the modification of both physical-mechanical characteristics and absorption shielding ability of hybrid composites.

scholarly journals Hyperbranched polyamide modified graphene oxide-reinforced polyurethane nanocomposites with enhanced mechanical properties

RSC Advances ◽  
2021 ◽  
Vol 11 (24) ◽  
pp. 14484-14494
Author(s):  
Yahao Liu ◽  
Jian Zheng ◽  
Xiao Zhang ◽  
Yongqiang Du ◽  
Guibo Yu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Graphene Oxide ◽  
High Performance ◽  
Cross Linking ◽  
Elongation At Break ◽  
Modified Graphene Oxide ◽  
High Performance Composite ◽  
Modified Graphene ◽  
Polyurethane Nanocomposites ◽  
Hyperbranched Polyamide

We successfully modified graphene oxide with amino-terminated hyperbranched polyamide (HGO), and obtained a high-performance composite with enhanced strength and elongation at break via cross-linking hydroxyl-terminated polybutadiene chains with HGO.

scholarly journals Smart Hydrogel Bilayers Prepared by Irradiation

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1753
Author(s):  
Weixian Huo ◽  
Heng An ◽  
Shuquan Chang ◽  
Shengsheng Yang ◽  
Yin Huang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Gamma Radiation ◽  
Antibacterial Properties ◽  
Cross Linking ◽  
Temperature Sensitive ◽  
Temperature Changes ◽  
Smart Hydrogel ◽  
Isopropyl Acrylamide ◽  
Hydrogel Synthesis ◽  
Potential Applications

Environment-responsive hydrogel actuators have attracted tremendous attention due to their intriguing properties. Gamma radiation has been considered as a green cross-linking process for hydrogel synthesis, as toxic cross-linking agents and initiators were not required. In this work, chitosan/agar/P(N-isopropyl acrylamide-co-acrylamide) (CS/agar/P(NIPAM-co-AM)) and CS/agar/Montmorillonite (MMT)/PNIPAM temperature-sensitive hydrogel bilayers were synthesized via gamma radiation at room temperature. The mechanical properties and temperature sensitivity of hydrogels under different agar content and irradiation doses were explored. The enhancement of the mechanical properties of the composite hydrogel can be attributed to the presence of agar and MMT. Due to the different temperature sensitivities provided by the two layers of hydrogel, they can move autonomously and act as a flexible gripper as the temperature changes. Thanks to the antibacterial properties of the hydrogel, their storage time and service life may be improved. The as prepared hydrogel bilayers have potential applications in control devices, soft robots, artificial muscles and other fields.

scholarly journals Double-Cross-Linked Networks Based on Methacryloyl Mucin

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1706
Author(s):  
Elena Olăreț ◽  
Brîndușa Bălănucă ◽  
Andra Mihaela Onaș ◽  
Jana Ghițman ◽  
Horia Iovu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aqueous Solution ◽  
Chemical Modification ◽  
Structural Modification ◽  
Aqueous Media ◽  
Cross Linking ◽  
Ph Values ◽  
Acid Aqueous Solution ◽  
Reaction Media ◽  
Double Cross

Mucin is a glycoprotein with proven potential in the biomaterials field, but its use is still underexploited for such applications. The present work aims to produce a synthesis of methacryloyl mucin single-network (SN) hydrogels and their double-cross-linked-network (DCN) counterparts. Following the synthesis of the mucin methacryloyl derivative, various SN hydrogels are prepared through the photopolymerization of methacrylate bonds, using reaction media with different pH values. The SN hydrogels are converted into DCN systems via supplementary cross-linking in tannic acid aqueous solution. The chemical modification of mucin is described, and the obtained product is characterized; the structural modification of mucin is assessed through FTIR spectroscopy, and the circular dichroism and the isoelectric point of methacryloyl mucin is evaluated. The affinity for aqueous media of both SN and DCN hydrogels is estimated, and the mechanical properties of the systems are assessed, both at macroscale through uniaxial compression and rheology tests and also at microscale through nanoindentation tests.

Sign in / Sign up

Export Citation Format

Share Document