scholarly journals Formulations of Organic Matter for Biodegridable Planting Bag

2018 ◽  
Vol 7 (4.10) ◽  
pp. 306
Author(s):  
Mochammad Chanan ◽  
Aniek Iriany ◽  
Atiek Iriany
Keyword(s):  
Tensile Strength ◽  
Water Hyacinth ◽  
Physical And Mechanical Properties ◽  
Material Composition ◽  
Organic C ◽  
Material Quality ◽  
Randomized Design ◽  
Plant Nursery ◽  
Chemical Content ◽  
Material Formulation

This research was aimed to generate an efficient and effective material formulation of planting bag using organic waste which could be applied to support the plant nursery technology. This research was conducted using completely randomized design with three times replication. The observable variables were: the chemical content of material including organic C, C/N, SOM, and N total. The variables of material quality were yield, tensile strength, and Valensky test. The result of this research indicated that the material composition of 25% water hyacinth: 50% straw: 25%  banana sheath produced higher N total, organic C and organic matters. Then, the material composition of 50% water hyacinth: 25% straw: 25% banana sheath generate material quality with higher tensile strength (33N/cm2). While the material composition consisting of 25% water hyacinth: 25% straw: 50% banana sheath produced higher yield value (80%). Due to the material proportion of water hyacinth, straw, and banana sheath, it affected the decrease and increase of light intensity whether in all season. It means biodegradable planting bag potentially substitute polybag or in organic planting bag with satisfied physical and mechanical properties.  

scholarly journals ANALISIS SIFAT MEKANIK LAS TIG PADA PLAT ALUMINIUM SERI 5 DENGAN VARIABEL KUAT ARUS 65; 70; 75 A UNTUK MANUFAKTUR KENDARAAN AIR SAMPAN (CANOE)

POROS ◽  
2018 ◽  
Vol 15 (2) ◽  
pp. 101
Author(s):  
Andika Wisnujati
Keyword(s):  
Tensile Strength ◽  
Tensile Testing ◽  
Physical And Mechanical Properties ◽  
Tig Welding ◽  
Material Composition ◽  
Tungsten Electrodes ◽  
Metal Filler ◽  
Strong Current ◽  
Ac Current ◽  
Aluminum Plates

Abstract: In general, water vehicles or water transport commonly called canoes are still used in villages for fishermen to fish in the sea and in rivers. Aluminum alloy in this research using Aluminum series 5. Background of this research is to analyze the strength of TIG weld (Tungsten Inert Gas) connection in the canoe to get reliable samples and no leakage. In high TIG welding the low temperature is determined by the high-low of the electric current being flowed. The aluminum plate for the canoe is subjected to material composition testing and tensile testing to determine the physical and mechanical properties of the TIG welding joints on the aluminum series 5. TIG welding with the current variable 65, 70 and 75 Ampere. Testing specimens of 2mm thick with dimensions of 24x16 cm where the electric arc flame is generated by tungsten electrodes (non-feeding electrodes) with metal workpieces. Test results obtained include that welding on aluminum series 5 is done with AC current (Alternating Current) due to the action of cleaning the metal surface is greater. Thin metal work, TIG welding can be used without metal filler. Material composition test showed that aluminum content of 97,76% and magnesium main addition element equal to 1.753%. In tensile testing, the strong variations of current used to connect aluminum plates are 65, 70, and 75 Ampere produce different tensile strength. The highest tensile strength is generated on plate grafting using a strong current of 75 Ampere with a yield of 165.91 MPa. This is because with a strong current of 75 A, the welding liquid enters and fuses into the center of the aluminum, resulting in a strong welding joint. 

scholarly journals The Effects of Doses and Methods of Lime Placement to N, P, K, Ca, Mg Content and Sugarcane Growth in Ultisol Lampung Tengah, Indonesia

2019 ◽  
Vol 3 (3) ◽  
pp. 166
Author(s):  
Heri Wahyudi ◽  
Azwar Ma’as ◽  
Eko Hanudin ◽  
Sri Nuryani Hidayah Utami
Keyword(s):  
Sugar Cane ◽  
Soil Nutrient ◽  
Nutrient Content ◽  
Soil Taxonomy ◽  
Total N ◽  
Organic C ◽  
Randomized Design ◽  
Ca Uptake ◽  
Chemical Content ◽  
Mg Content

Land circumstances on Seputih Mataram, Lampung included in dried area which is consist of Ultisols soil (soil taxonomy). Ultisol consist of H2O which has pH of less than 5.5. It will cause the amount of soil nutrient that absorbed is not optimal yet. This research aimed to know the influence of adding dolomite to the soil chemical content (pH number of H2O, KCl, content of total N, available P, exch-K, exch-Ca, exch-Mg, Organic-C, ratio C/N, exch-Al, exch-H, CEC), nutrient content on the leaf (such as N, P, K, Ca, Mg) and sugar cane physic. This research used Completely Randomized Design 2 factors with 3 blocks repetition. First factor was the dolomite doses in six contents: without the dolomite (K0), 500 kg/ha (K1), 1000 kg/ha (K2), 2000 kg/ha (K3), 4000 kg/ha (K4) and 6000 kg/ha (K5). The second factor (R) was the depth of dolomite placement, consist of: (R1) dolomite with 0-20 cm depth and (R2) dolomite with 20-40 cm depth. The observation used to know the soil chemical content, the leaf nutrients and the variables that used into the research. The observation results variant analyzed (ANOVA) in 5 % and continued with the Duncan’s Multiple Range Test (DMRT) in 5 % if the result showed the real differentiation. The result showed that the depth of dolomite was not real influence to the amount of Nitrogen (N), Phosphorus (P), Potassium (K), Calcium (Ca), and Magnesium (Mg) in leaf. Dolomite addition was real influence for Calcium (Ca) uptake in leaf, but it was not real influenced the leaf uptake. Dolomite addition was real influence in the leaf content and leaf Magnesium (Mg) uptake. 6000 kg/ha dolomite for physical soil characteristic ( pH H2O, pH KCL, C/N ratio, K, P, Ca, Mg,Exch-H), leaf nutrient ( N, K, Ca), Mg and Ca uptake on leaf also sugar cane tonnage per hectare showed the maximum result.

scholarly journals Damage Evolution of Granodiorite after Heating and Cooling Treatments

Minerals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 779
Author(s):  
Mohamed Gomah ◽  
Guichen Li ◽  
Salah Bader ◽  
Mohamed Elkarmoty ◽  
Mohamed Ismael
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Failure Mode ◽  
Physical And Mechanical Properties ◽  
P Wave ◽  
Physical Parameters ◽  
Slow Cooling ◽  
Heating And Cooling ◽  
Natural Rock ◽  
The Impact

The awareness of the impact of high temperatures on rock properties is essential to the design of deep geotechnical applications. The purpose of this research is to assess the influence of heating and cooling treatments on the physical and mechanical properties of Egyptian granodiorite as a degrading factor. The samples were heated to various temperatures (200, 400, 600, and 800 °C) and then cooled at different rates, either slowly cooled in the oven and air or quickly cooled in water. The porosity, water absorption, P-wave velocity, tensile strength, failure mode, and associated microstructural alterations due to thermal effect have been studied. The study revealed that the granodiorite has a slight drop in tensile strength, up to 400 °C, for slow cooling routes and that most of the physical attributes are comparable to natural rock. Despite this, granodiorite thermal deterioration is substantially higher for quick cooling than for slow cooling. Between 400:600 °C is ‘the transitional stage’, where the physical and mechanical characteristics degraded exponentially for all cooling pathways. Independent of the cooling method, the granodiorite showed a ductile failure mode associated with reduced peak tensile strengths. Additionally, the microstructure altered from predominantly intergranular cracking to more trans-granular cracking at 600 °C. The integrity of the granodiorite structure was compromised at 800 °C, the physical parameters deteriorated, and the rock tensile strength was negligible. In this research, the temperatures of 400, 600, and 800 °C were remarked to be typical of three divergent phases of granodiorite mechanical and physical properties evolution. Furthermore, 400 °C could be considered as the threshold limit for Egyptian granodiorite physical and mechanical properties for typical thermal underground applications.

scholarly journals Thermal, Physical and Mechanical Properties of Poly(Butylene Succinate)/Kenaf Core Fibers Composites Reinforced with Esterified Lignin

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2359
Author(s):  
Harmaen Ahmad Saffian ◽  
Masayuki Yamaguchi ◽  
Hidayah Ariffin ◽  
Khalina Abdan ◽  
Nur Kartinee Kassim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Loss Modulus ◽  
Physical And Mechanical Properties ◽  
Weight Percent Gain ◽  
Weight Percent ◽  
Esterification Reaction ◽  
Butylene Succinate ◽  
Kenaf Core ◽  
Modified Lignin

In this study, Kraft lignin was esterified with phthalic anhydride and was served as reinforcing filler for poly(butylene succinate) (PBS). Composites with different ratios of PBS, lignin (L), modified lignin (ML) and kenaf core fibers (KCF) were fabricated using a compounding method. The fabricated PBS composites and its counterparts were tested for thermal, physical and mechanical properties. Weight percent gain of 4.5% after lignin modification and the FTIR spectra has confirmed the occurrence of an esterification reaction. Better thermo-mechanical properties were observed in the PBS composites reinforced with modified lignin and KCF, as higher storage modulus and loss modulus were recorded using dynamic mechanical analysis. The density of the composites fabricated ranged from 1.26 to 1.43 g/cm3. Water absorption of the composites with the addition of modified lignin is higher than that of composites with unmodified lignin. Pure PBS exhibited the highest tensile strength of 18.62 MPa. Incorporation of lignin and KCF into PBS resulted in different extents of reduction in tensile strength (15.78 to 18.60 MPa). However, PBS composite reinforced with modified lignin exhibited better tensile and flexural strength compared to its unmodified lignin counterpart. PBS composite reinforced with 30 wt% ML and 20 wt% KCF had the highest Izod impact, as fibers could diverge the cracking propagation of the matrix. The thermal conductivity value of the composites ranged from 0.0903 to 0.0983 W/mK, showing great potential as a heat insulator.

scholarly journals Properties and Structure of Concretes Doped with Production Waste of Thermoplastic Elastomers from the Production of Car Floor Mats

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 872
Author(s):  
Malgorzata Ulewicz ◽  
Alina Pietrzak
Keyword(s):  
Tensile Strength ◽  
Production Process ◽  
Compression Strength ◽  
Physical And Mechanical Properties ◽  
Thermoplastic Elastomer ◽  
Thermoplastic Elastomers ◽  
Production Waste ◽  
Fine Aggregate ◽  
Freezing And Thawing ◽  
Average Decrease

This article presents physical and mechanical properties of concrete composites that include waste thermoplastic elastomer (TPE) from the production process of car floor mats. Waste elastomer (2–8 mm fraction) was used as a substitute for fine aggregate in quantities of 2.5, 5.0, 7.5, and 10% of the cement weight. For all series of concrete, the following tests were carried out: compression strength, bending tensile strength, splitting tensile strength, absorbability, density, resistance to water penetration under pressure, frost resistance, and abrasion resistance, according to applicable standards. Moreover, SEM/EDS analysis was carried out on the surface microstructure of synthesized concrete composites. It was proven that the use of production waste from the production process of car floor mats in the quantity of 2.5% does not influence the change of the concrete microstructure and it does not result in the decrease of the mechanical parameters of concrete modified with waste. All concrete modified with the addition of waste meet standards requirements after carrying out 15 cycles of freezing and thawing, and the average decrease in compression strength did not exceed 20%. Adding waste in the quantity of 2.5% allows for limiting the use of aggregate by about 5%, which is beneficial for the natural environment.

Effect of Castor Oil Impregnation on the Physical and Mechanical Properties of Bacterial Cellulose

2012 ◽  
Vol 3 (1) ◽  
pp. 13-26
Author(s):  
Myrtha Karina ◽  
Lucia Indrarti ◽  
Rike Yudianti ◽  
Indriyati
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Bacterial Cellulose ◽  
Young’S Modulus ◽  
Castor Oil ◽  
Young's Modulus ◽  
Physical And Mechanical Properties ◽  
Scanning Electron Micrographs ◽  
Elongation At Break ◽  
Acetone Water

The effect of castor oil on the physical and mechanical properties of bacterial cellulose is described. Bacterial cellulose (BC) was impregnated with 0.5–2% (w/v) castor oil (CO) in acetone–water, providing BCCO films. Scanning electron micrographs revealed that the castor oil penetrated the pores of the bacterial cellulose, resulting in a smoother morphology and enhanced hydrophilicity. Castor oil caused a slight change in crystallinity indices and resulted in reduced tensile strength and Young's modulus but increased elongation at break. A significant reduction in tensile strength and Young's modulus was achieved in BCCO films with 2% castor oil, and there was an improvement in elongation at break and hydrophilicity. Impregnation with castor oil, a biodegradable and safe plasticiser, resulted in less rigid and more ductile composites.

scholarly journals Enhancement of Mechanical Properties and Porosity of Concrete Using Steel Slag Coarse Aggregate

Materials ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 2865
Author(s):  
Md Jihad Miah ◽  
Md. Munir Hossain Patoary ◽  
Suvash Chandra Paul ◽  
Adewumi John Babafemi ◽  
Biranchi Panda
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Microstructural Analysis ◽  
Steel Slag ◽  
Physical And Mechanical Properties ◽  
Length Change ◽  
Sustainable Building ◽  
Burnt Clay ◽  
Lower Porosity ◽  
Furnace Steel

This paper investigates the possibility of utilizing steel slags produced in the steelmaking industry as an alternative to burnt clay brick aggregate (BA) in concrete. Within this context, physical, mechanical (i.e., compressive and splitting tensile strength), length change, and durability (porosity) tests were conducted on concrete made with nine different percentage replacements (0%, 10%, 20%, 30%, 40%, 50%, 60%, 80%, and 100% by volume of BA) of BA by induction of furnace steel slag aggregate (SSA). In addition, the chemical composition of aggregate through X-ray fluorescence (XRF) analysis and microstructural analysis through scanning electron microscopy (SEM) of aggregates and concrete were performed. The experimental results show that the physical and mechanical properties of concrete made with SSA were significantly higher than that of concrete made with BA. The compressive and tensile strength increased by 73% when SSA fully replaced BA. The expansion of concrete made with SSA was a bit higher than the concrete made with BA. Furthermore, a significant lower porosity was observed for concrete made with SSA than BA, which decreased by 40% for 100% SSA concrete than 100% BA concrete. The relation between compressive and tensile strength with the porosity of concrete mixes are in agreement with the relationships presented in the literature. This study demonstrates that SSA can be used as a full replacement of BA, which is economical, conserves the natural aggregate, and is sustainable building material since burning brick produces a lot of CO2.

scholarly journals Composites from Thermoplastic Natural Rubber Reinforced Rubberwood Sawdust: Effects of Sawdust Size and Content on Thermal, Physical, and Mechanical Properties

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Chatree Homkhiew ◽  
Surasit Rawangwong ◽  
Worapong Boonchouytan ◽  
Wiriya Thongruang ◽  
Thanate Ratanawilai
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
High Density Polyethylene ◽  
High Performance ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Shore Hardness ◽  
Thermoplastic Natural Rubber ◽  
Plastic Content

The aim of this work is to investigate the effects of rubberwood sawdust (RWS) size and content as well as the ratio of natural rubber (NR)/high-density polyethylene (HDPE) blend on properties of RWS reinforced thermoplastic natural rubber (TPNR) composites. The addition of RWS about 30–50 wt% improved the modulus of the rupture and tensile strength of TPNR composites blending with NR/HDPE ratios of 60/40 and 50/50. TPNR composites reinforced with RWS 80 mesh yielded better tensile strength and modulus of rupture than the composites with RWS 40 mesh. The TPNR/RWS composites with larger HDPE content gave higher tensile, flexural, and Shore hardness properties and thermal stability as well as lower water absorption. The TPNR/RWS composites with larger plastic content were therefore suggested for applications requiring high performance of thermal, physical, and mechanical properties.

Effect of Wood Filler Concentration on Physical and Mechanical Properties of PLA-Based Composites

2021 ◽  
Vol 887 ◽  
pp. 110-115
Author(s):  
G.A. Sabirova ◽  
R.R. Safin ◽  
N.R. Galyavetdinov
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Composite Materials ◽  
Impact Strength ◽  
Wood Flour ◽  
Experimental Studies ◽  
Physical And Mechanical Properties ◽  
Filler Concentration ◽  
High Concentration

This paper presents the findings of experimental studies of the physical and mechanical properties of wood-filled composites based on polylactide (PLA) and vegetable filler in the form of wood flour (WF) thermally modified at 200-240 °C. It also reveals the dependence of the tensile strength, impact strength, bending elastic modulus, and density of composites on the amount of wood filler and the temperature of its thermal pre-modification. We established that an increase in the concentration of the introduced filler and the degree of its heat treatment results in a decrease of the tensile strength, impact strength and density of composite materials, while with a lower binder content, thermal modification at 200 °C has a positive effect on bending elastic modulus. We also found that 40 % content of a wood filler heated to 200 °C is sufficient to maintain relatively high physical and mechanical properties of composite materials. With a higher content of a wood filler, the cost can be reduced but the quality of products made of this material may significantly deteriorate. However, depending on the application and the life cycle of this product, it is possible to develop a formulation that includes a high concentration of filler.

Sign in / Sign up

Export Citation Format

Share Document