scholarly journals The Impact of Multiple Seam Mining Exploitations on Seismic Activity and State of Stress

2017 ◽  
Vol 39 (1) ◽  
pp. 53-62 ◽  
Author(s):  
Tadeusz Majcherczyk ◽  
Zbigniew Niedbalski

Abstract The paper presents an analysis of seismic activity for selected areas of hard coal mine executing exploitation in a rock mass with a variable degree of rock disturbance, i.e., also with a varied number of previous mined-out seams. A distribution of vertical stress and a value of vertical stress concentration coefficient were also determined in the strata of immediate roof of the seams planned for mining. In the analyzed case, despite the lack of thick and solid strata of sandstones in the roof, the rock mass emits seismic activity, where the energy largely depends upon an impact of exploitation edges and tectonic disturbance.

2018 ◽  
Vol 36 ◽  
pp. 02007 ◽  
Author(s):  
Elżbieta Pilecka ◽  
Dariusz Szwarkowski

In the article, a numerical analysis of the impact of the width of the fault zone on land surface tremors on the area of the “Rydułtowy – Anna” hard coal mine was performed. The analysis covered the dynamic impact of the actual seismic wave after the high-energy tremor of 7 June 2013. Vibrations on the land surface are a measure of the mining damage risk. It is particularly the horizontal components of land vibrations that are dangerous to buildings which is reflected in the Mining Scales of Intensity (GSI) of vibrations. The run of a seismic wave in the rock mass from the hypocenter to the area’s surface depends on the lithology of the area and the presence of fault zones. The rock mass network cut by faults of various widths influences the amplitude of tremor reaching the area’s surface. The analysis of the impact of the width of the fault zone was done for three alternatives.


2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Xinping Guo ◽  
Annan Jiang ◽  
Shanyong Wang

The main challenge for metro station construction is to ensure the construction schedule while minimizing the impact on the surrounding environment. Based on the characteristics of the upper-soft and lower-hard stratum in the Dalian city of China, a special structure with six pilot tunnels and three spans of the pile-beam-arch (PBA) method is proposed and applied to the construction of the Labor Park metro station. In this study, laboratory experiments, numerical simulation analysis, and field monitoring data are used to investigate the applicability of six pilot tunnels and three spans of the PBA method in the process of construction. In the process of numerical simulation, the ground surface settlement, arch vertical displacement, the horizontal displacement of rock mass on both sides of the station, and vertical stress of support structure are analyzed. The numerical simulation results are found to be in good agreement with field measurement. Furthermore, the results indicate that, in the construction of six pilot tunnels and three spans of the PBA method, pilot tunnel construction and arch construction have a great influence on the surface settlement. The part of the initial vertical support of the pilot tunnels is removed, which caused the change of the position of maximum vertical stress and the redistribution of vertical stress. Because of reinforcement by side piles on both sides of the station, the horizontal displacement of the rock mass was reduced by 44.76% compared with that without reinforcement. The six pilot tunnels and three spans of the PBA method can effectively control the surface settlement, arch vertical displacement, and horizontal displacement of the rock mass.


Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2371
Author(s):  
Józef Jonak ◽  
Robert Karpiński ◽  
Andrzej Wójcik

The paper presents the results of a numerical analysis (FEM) describing the effect of the undercutting head angle on the formation of the rock mass failure zone during the initial stages of failure propagation. The research was carried out in the context of developing a technology for rock extraction by controlled pull-out of undercut anchors installed in the rock mass. The focus was on the initial stage of crack propagation and its trajectory for anchors embedded at an assumed constant depth and a value of the friction coefficient of the rock against the anchor head. It is shown that smaller angles favor smaller stripping angles and an increased radial impact of the head on the rock material (in the plane perpendicular to the head axis), while the impact of heads with larger angles is found to favor larger fracture penetration angles and faster penetration towards the free rock surface.


2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Chengliang Zhang ◽  
Danyong Ye ◽  
Ping Yang ◽  
Shunchuan Wu ◽  
Chao Wang

With the increased mining depth, the dynamic disaster of rock burst in coal mines has become increasingly prominent, and the impact tendency of coal and rock mass in deep coal seam mining is a necessary condition for the occurrence of rock burst and an important index to measure the failure of coal and rock mass. Laboratory tests and numerical tests were used to study the impact tendency of coal and roof strata, including the deformation characteristics, failure characteristics, and bending energy index of the coal and rock mass of different sizes, the failure law and energy evolution characteristics of tlhe coal and rock mass under the same size, and the unloading characteristics of the coal and rock mass under the same size and different confining pressures. The results are shown as follows: (1) The rock roof was determined to have a weak impact tendency through the mechanical test. (2) With the increased size, the microcracks in the rock samples increased correspondingly, and the increased meso-defect leading to the increased heterogeneity was an essential reason for the size effect. The strength of the rock mass decreased with the increased specimen size. The larger the specimen size was, the lower the bending energy index was. (3) Triaxial loading and unloading were tested for the same size under different surrounding rocks. Under the same loading conditions, with the increased confining pressure, the strength and bending energy index of rock mass increased correspondingly, and the failure of rock mass transformed from tensile to shear failure. The failure form and strength characteristic of rock under the unloading condition are different from those under the loading condition. The failure degree was intense, with a high bending energy index. Compared with the loading situation, the impact tendency caused by unloading was higher, and the dynamic impact disaster was more likely to occur.


2019 ◽  
Vol 11 (9) ◽  
pp. 2570 ◽  
Author(s):  
Dawid Szurgacz ◽  
Jarosław Brodny

One of the basic tasks of powered roof support is to protect the longwall excavation against deformation of the rock mass during the underground exploitation of hard coal. The behavior of the rock mass during mining is difficult to predict. Therefore, the loads acting on the support are diverse in terms of nature, direction and force. The dynamic load resulting from rock bursts, relaxation and tremors may lead to particularly dangerous consequences involving the functionality of the workings and the safety of the crew. The powered roof support will function properly only if the elements dynamically loaded are under control at the moment of impact. The article presents the results of tests of the basic powered roof support’s element − a hydraulic leg impacted by dynamic load. The source of the load was a free falling impact mass dropped from a certain height. The tests covered the actual hydraulic leg with all hydraulic equipment used in the powered roof support. During the tests, the original measurement-recording system developed by the authors was used, in which, among others, a high-speed dynamic camera was used to record movements of the leg’s elements. The original research methodology developed together with the measurement system enabled the registration of many parameters of the leg’s work under dynamic load. In particular, this applies to time series of pressure in the leg and the value of its withdrawal depending on the energy of the impact. The individual phases of the leg’s work were also registered, including the opening and closing of the safety valve protecting the leg against overloading. The obtained results broaden knowledge in the field of hydraulic legs used in the mining support under dynamic load. At the same time, they are a valuable source of information for mine maintenance services and should be applied to the design process, selection and operation of a powered roof support in dynamic conditions. The subject of the article fits in with the philosophy of sustainable development, especially in the field of full use of options of the support and ensuring safe and environmentally friendly mining processes.


2013 ◽  
Vol 58 (2) ◽  
pp. 449-463 ◽  
Author(s):  
Mieczysław Żyła ◽  
Agnieszka Dudzińska ◽  
Janusz Cygankiewicz

Ethane constitutes an explosive gas. It most often accompanies methane realizing during exploitation and mining works. In this paper the results of ethane sorption have been discussed on three grain classes of six selected hard coal samples collected from active Polish coalmines. On the basis of obtained results, it has been stated that the tested hard coals prove differentiated sorption power with reference to ethane. Te extreme amount of ethane is sorbed by low carbonized hard coal from “Jaworzno” coalmine. This sort of coal shows great porosity, and great content of oxygen and moisture. The least amount of ethane is sorbed by hard coal from “Sośnica” coalmine. This sort of coal possesses relatively a great deal of ash contents. Together with the process of coal disintegration, the amount of sorbed ethane increases for all tested coal samples. Between tested coals there are three medium carbonized samples collected from “Pniówek”, “Chwałowice” “Zofiówka” coalmines which are characterized by small surface values counted according to model BET from nitrogen sorption isotherms determined at the temperature of 77.5 K. The samples of these three coals prove the highest, from between tested coals, increase of ethane sorption occurring together with their disintegration. These samples disintegrated to 0,063-0,075 mm grain class sorb ethane in the amount corresponding with the sorption quantity of low carbonized coal from “Jaworzno” coalmine in 0.5-0.7 mm grain class. It should be marked that the low carbonized samples collected from “Jaworzno” and Wesoła” coalmines possess large specific surface and great porosity and belong to coal group of “loose” spatial structure. Regarding profusion of sorbed ethane on disintegrated medium carbonized samples from “Pniówek”, “Zofiówka”, “Chwałowice” coalmines it can be supposed that in the process of coal disintegration, breaking their “compact’ structure occurs. Loosened structure of medium carbonized coals results in increasing accessibility of ethane particles to sorption centres both electron donors and electron acceptors which are present on hard coal surface. The surface sorption centre increase may result in formation a compact layer of ethane particles on coal surface. In the formed layer, not only the strengths of vertical binding of ethane particles with the coal surface appear but also the impact of horizontal strengths appears which forms a compact layer of sorbed ethane particles. The surface layer of ethane particles may lead to explosion.


2020 ◽  
Vol 19 (12) ◽  
pp. 2225-2252
Author(s):  
E.V. Popov ◽  
V.L. Simonova ◽  
O.V. Komarova ◽  
S.S. Kaigorodova

Subject. The emergence of new ways of interaction between sellers and buyers, the formation of new sales channels and product promotion based on the use of digital economy tools is at the heart of improving the business processes. Social networks became a tool for development; their rapid growth necessitates theoretical understanding and identification of potential application in enterprise's business process digitalization. Objectives. We explore the role of social media in the digitalization of business processes, systematize the impact of social networks on business processes of enterprises in the digital economy. Methods. The theoretical and methodological analysis of social networks as a tool for digitalization of company's business processes rests on the content analysis of domestic and foreign scientific studies, comparison, generalization and systematization. Results. We highlight the key effects of the impact of social networks on the business processes of the company; show that the digitalization of business processes should be considered in the context of a value-based approach, aimed at creating a value through the algorithmization of company operations. We determine that social networks are one of the most important tools for digitalization of company's business processes, as they have a high organizational and management potential. We also systematize the effects of social media on company's business processes. Conclusions. We present theoretical provisions of the impact of social networks on business processes of enterprises, which will enable to model and organize ideas about the development of digital ecosystems and the formation of business models.


Author(s):  
Rui Wu ◽  
Penghui Zhang ◽  
Pinnaduwa H. S. W. Kulatilake ◽  
Hao Luo ◽  
Qingyuan He

AbstractAt present, non-pillar entry protection in longwall mining is mainly achieved through either the gob-side entry retaining (GER) procedure or the gob-side entry driving (GED) procedure. The GER procedure leads to difficulties in maintaining the roadway in mining both the previous and current panels. A narrow coal pillar about 5–7 m must be left in the GED procedure; therefore, it causes permanent loss of some coal. The gob-side pre-backfill driving (GPD) procedure effectively removes the wasting of coal resources that exists in the GED procedure and finds an alternative way to handle the roadway maintenance problem that exists in the GER procedure. The FLAC3D software was used to numerically investigate the stress and deformation distributions and failure of the rock mass surrounding the previous and current panel roadways during each stage of the GPD procedure which requires "twice excavation and mining". The results show that the stress distribution is slightly asymmetric around the previous panel roadway after the “primary excavation”. The stronger and stiffer backfill compared to the coal turned out to be the main bearing body of the previous panel roadway during the "primary mining". The highest vertical stresses of 32.6 and 23.1 MPa, compared to the in-situ stress of 10.5 MPa, appeared in the backfill wall and coal seam, respectively. After the "primary mining", the peak vertical stress under the coal seam at the floor level was slightly higher (18.1 MPa) than that under the backfill (17.8 MPa). After the "secondary excavation", the peak vertical stress under the coal seam at the floor level was slightly lower (18.7 MPa) than that under the backfill (19.8 MPa); the maximum floor heave and maximum roof sag of the current panel roadway were 252.9 and 322.1 mm, respectively. During the "secondary mining", the stress distribution in the rock mass surrounding the current panel roadway was mainly affected by the superposition of the front abutment pressure from the current panel and the side abutment pressure from the previous panel. The floor heave of the current panel roadway reached a maximum of 321.8 mm at 5 m ahead of the working face; the roof sag increased to 828.4 mm at the working face. The peak abutment pressure appeared alternately in the backfill and the coal seam during the whole procedure of "twice excavation and mining" of the GPD procedure. The backfill provided strong bearing capacity during all stages of the GPD procedure and exhibited reliable support for the roadway. The results provide scientific insight for engineering practice of the GPD procedure.


Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 562
Author(s):  
Marek Jendryś ◽  
Andrzej Hadam ◽  
Mateusz Ćwiękała

The following article analyzes the effectiveness of directional hydraulic fracturing (DHF) as a method of rock burst prevention, used in black coal mining with a longwall system. In order to define changes in seismic activity due to DHF at the “Rydułtowy” Black Coal Mine (Upper Silesia, Poland), observations were made regarding the seismic activity of the rock mass during coal mining with a longwall system using roof layers collapse. The seismic activity was recorded in the area of the longwall itself, where, on a part of the runway, the rock mass was expanded before the face of the wall by interrupting the continuity of the rock layers using DHF. The following article presents measurements in the form of the number and the shock energy in the area of the observed longwall, which took place before and after the use of DHF. The second part of the article unveils the results of numerical modeling using the discrete element method, allowing to track the formation of goafs for the variant that does not take DHF into consideration, as well as with modeled fractures tracing DHF carried out in accordance with the technology used at “Rydułtowy” coal mine.


Atmosphere ◽  
2021 ◽  
Vol 12 (6) ◽  
pp. 707
Author(s):  
Petros Vasilakos ◽  
Yongtao Hu ◽  
Armistead Russell ◽  
Athanasios Nenes

Formation of aerosol from biogenic hydrocarbons relies heavily on anthropogenic emissions since they control the availability of species such as sulfate and nitrate, and through them, aerosol acidity (pH). To elucidate the role that acidity and emissions play in regulating Secondary Organic Aerosol (SOA), we utilize the 2013 Southern Oxidant and Aerosol Study (SOAS) dataset to enhance the extensive mechanism of isoprene epoxydiol (IEPOX)-mediated SOA formation implemented in the Community Multiscale Air Quality (CMAQ) model (Pye et al., 2013), which was then used to investigate the impact of potential future emission controls on IEPOX OA. We found that the Henry’s law coefficient for IEPOX was the most impactful parameter that controls aqueous isoprene OA products, and a value of 1.9 × 107 M atm−1 provides the best agreement with measurements. Non-volatile cations (NVCs) were found in higher-than-expected quantities in CMAQ and exerted a significant influence on IEPOX OA by reducing its production by as much as 30% when present. Consistent with previous literature, a strong correlation of isoprene OA with sulfate, and little correlation with acidity or liquid water content, was found. Future reductions in SO2 emissions are found to not affect this correlation and generally act to increase the sensitivity of IEPOX OA to sulfate, even in extreme cases.


Sign in / Sign up

Export Citation Format

Share Document