An Application of Passive Voltage Contrast (PVC) to Failure Analysis of CMOS LSIs Using Secondary Electron Collection

1999 ◽  
Author(s):  
Akira Nishikawa ◽  
Naoko I. Kato ◽  
Yoshiteru Kohno ◽  
Nobuhito Miura ◽  
Masao Shimizu
Keyword(s):  
Failure Analysis ◽  
Short Circuit ◽  
Cross Sectional ◽  
Backscattered Electrons ◽  
Emission Efficiency ◽  
Electron Collection ◽  
Open Defect ◽  
Absorption Current ◽  
Voltage Contrast ◽  
Acceleration Voltage

Abstract This paper describes a method for applying passive voltage contrast (PVC) in the failure analysis of CMOS LSIs using a conventional scanning electron microscope (SEM), and demonstrates the effectiveness of this method. It was confirmed by measurement of the stage absorption current that the combined emission efficiency of secondary and backscattered electrons from aluminum is larger than 1 at acceleration voltages lower than about 2.5 kV. This means that local positive charges should be generated on a conductor in association with its irradiation with an electron beam at a relatively low acceleration voltage. However, a pn junction connected to the conductor would change the potential. The potential is still positive if the conductor is connected to a reverse-biased diode but becomes lower if such a diode is forward-biased. The PVC signal observed on the conductor should be defined according to the bias state of any diode connected to the conductor. Therefore, for failure analysis applications, if the bias state of a diode connected to a suspicious conductor is known, the PVC observation is useful for determining whether there is an open defect or a short-circuit defect. Some case studies are presented to demonstrate the effectiveness of the method. Cross-sectional TEM observations of defects localized in this way are also included.

Unique Approaches to Isolate Nanoscale Defect in Snake-Comb Test Structure

2015 ◽  
Author(s):  
Sujing Xie ◽  
Nathan Wang ◽  
Chaoying Chen ◽  
Qindi Wu
Keyword(s):  
Failure Analysis ◽  
Electrical Resistance ◽  
Test Structure ◽  
Yield Enhancement ◽  
Nanometer Scale ◽  
Cross Sectional ◽  
Root Cause ◽  
Unique Approach ◽  
Voltage Contrast ◽  
Root Cause Identification

Abstract Multiple techniques including electrical resistance measurement plus calculation, cross-sectional view of passive voltage contrast (XPVC) sequential searching, planar and cross-section STEM are successfully used to isolate a nanoscale defect, single metallic stringer in a snakecomb test structure. The defect could not be found by traditional failure analysis methods or procedures. The unique approach presented here, expands failure analysis capabilities to the detection of nanometer-scale defects and the identification of their root causes. With continuous shrinking feature sizes, the need of such techniques becomes more vital to failure analysis and root cause identification, and therefore yield enhancement in fabrication.

Analysis of Voltage Contrast in Secondary Electron Images Using a High-Energy Electron Spectrometer

2019 ◽  
Author(s):  
Natsuko Asano ◽  
Shunsuke Asahina ◽  
Natasha Erdman
Keyword(s):  
Focused Ion Beam ◽  
Ion Beam ◽  
Sample Surface ◽  
High Energy ◽  
Secondary Electrons ◽  
Analysis Technique ◽  
Quantitative Understanding ◽  
Voltage Contrast ◽  
Acceleration Voltage ◽  
Failure Localization

Abstract Voltage contrast (VC) observation using a scanning electron microscope (SEM) or a focused ion beam (FIB) is a common failure analysis technique for semiconductor devices.[1] The VC information allows understanding of failure localization issues. In general, VC images are acquired using secondary electrons (SEs) from a sample surface at an acceleration voltage of 0.8–2.0 kV in SEM. In this study, we aimed to find an optimized electron energy range for VC acquisition using Auger electron spectroscopy (AES) for quantitative understanding.

Rapid Failure Analysis of Low-Yielding Electrical Test Structures Using E-beam Physical and Voltage Contrast Inspection

2013 ◽  
Author(s):  
Oliver D. Patterson ◽  
Deborah A. Ryan ◽  
Xiaohu Tang ◽  
Shuen Cheng Lei
Keyword(s):  
Failure Analysis ◽  
Defect Detection ◽  
High Volume ◽  
The Other ◽  
Defect Inspection ◽  
Electrical Test ◽  
Detection Mode ◽  
Rapid Generation ◽  
Voltage Contrast ◽  
Additional Support

Abstract In-line E-beam inspection may be used for rapid generation of failure analysis (FA) results for low yielding test structures. This approach provides a number of advantages: 1) It is much earlier than traditional FA, 2) de-processing isn’t required, and 3) a high volume of sites can be processed with the additional support of an in-line FIB. Both physical defect detection and voltage contrast inspection modes are useful for this application. Voltage contrast mode is necessary for isolation of buried defects and is the preferred approach for opens, because it is faster. Physical defect detection mode is generally necessary to locate shorts. The considerations in applying these inspection modes for rapid failure analysis are discussed in the context of two examples: one that lends itself to physical defect inspection and the other, more appropriately addressed with voltage contrast inspection.

Application of Scan Based FA and Advanced Passive Voltage Contrast Technique in Defect Isolation

2003 ◽  
Author(s):  
Michael B. Schmidt ◽  
Noor Jehan Saujauddin
Keyword(s):  
Failure Analysis ◽  
Large Scale ◽  
Fault Isolation ◽  
Electronic Information ◽  
Scan Testing ◽  
Challenging Environment ◽  
Contrast Technique ◽  
Defect Isolation ◽  
Voltage Contrast ◽  
Higher Sensitivity

Abstract Scan testing and passive voltage contrast (PVC) techniques have been widely used as failure analysis fault isolation tools. Scan diagnosis can narrow a failure to a given net and passive voltage contrast can give real-time, large-scale electronic information about a sample at various stages of deprocessing. In the highly competitive and challenging environment of today, failure analysis cycle time is very important. By combining scan FA with a much higher sensitivity passive voltage contrast technique, one can quickly find defects that have traditionally posed a great challenge.

Failure Analysis Due to Slightly Unetched Hard Mask Using Nano Probe

2013 ◽  
Author(s):  
Jong Hak Lee ◽  
Jong Eun Kim ◽  
Chang Su Park ◽  
Nam Il Kim ◽  
Jang Won Moon ◽  
...  
Keyword(s):  
Leakage Current ◽  
Circuit Simulation ◽  
The State ◽  
Physical Analysis ◽  
Cross Sectional ◽  
Hard Mask ◽  
Current Flows ◽  
Voltage Contrast ◽  
The One ◽  
Zero Voltage

Abstract In this work, a slightly unetched gate hard mask failure was analyzed by nano probing. Although unetched hard mask failures are commonly detected from the cross sectional view with FIB or FIB-TEM and planar view with the voltage contrast, in this case of the very slightly unetched hard mask, it was difficult to find the defects within the failed area by physical analysis methods. FIB is useful due to its function of milling and checking from the one region to another region within the suspected area, but the defect, located under contact was very tiny. So, it could not be detected in the tilted-view of the FIB. However, the state of the failure could be understood from the electrical analysis using a nano probe due to its ability to probe contact nodes across the fail area. Among the transistors in the fail area, one transistor’s characteristics showed higher leakage current and lower ON current than expected. After physical analysis, slightly remained hard mask was detected by TEM. Chemical processing was followed to determine the gate electrode (WSi2) connection to tungsten contact. It was also proven that when gate is floated, more leakage current flows compared to the state that the zero voltage is applied to the gate. This was not verified by circuit simulation due to the floating nodes.

A Study of Electron Beam Irradiation Influence on Device Contact Junction Characteristics of Advanced DRAM Using Atomic Force Probing

2013 ◽  
Author(s):  
Wei-Chih Wang ◽  
Jian-Shing Luo
Keyword(s):  
Electron Beam ◽  
Electron Beam Irradiation ◽  
Forward Bias ◽  
Irradiation Damage ◽  
Beam Irradiation ◽  
Excess Current ◽  
Atomic Force ◽  
Order Of Magnitude ◽  
Voltage Contrast ◽  
Acceleration Voltage

Abstract In this paper, we revealed p+/n-well and n+/p-well junction characteristic changes caused by electron beam (EB) irradiation. Most importantly, we found a device contact side junction characteristic is relatively sensitive to EB irradiation than its whole device characteristic; an order of magnitude excess current appears at low forward bias region after 1kV EB acceleration voltage irradiation (Vacc). Furthermore, these changes were well interpreted by our Monte Carlo simulation results, the Shockley-Read Hall (SRH) model and the Generation-Recombination (G-R) center trap theory. In addition, four essential examining items were suggested and proposed for EB irradiation damage origins investigation and evaluation. Finally, by taking advantage of the excess current phenomenon, a scanning electron microscope (SEM) passive voltage contrast (PVC) fault localization application at n-FET region was also demonstrated.

Utilizing Nanoprobing and Circuit Diagnostics to Identify Key Failure Mechanism of Otherwise Nonvisible Defects in 20 nm Logic Devices

2014 ◽  
Author(s):  
M.K. Dawood ◽  
C. Chen ◽  
P.K. Tan ◽  
S. James ◽  
P.S. Limin ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Contact Layer ◽  
Fault Isolation ◽  
Tem Analysis ◽  
Logic Devices ◽  
Technology Advancement ◽  
Transmission Electron ◽  
Voltage Contrast ◽  
Almost All ◽  
20 Nm

Abstract In this work, we present two case studies on the utilization of advanced nanoprobing on 20nm logic devices at contact layer to identify the root cause of scan logic failures. In both cases, conventional failure analysis followed by inspection of passive voltage contrast (PVC) failed to identify any abnormality in the devices. Technology advancement makes identifying failure mechanisms increasingly more challenging using conventional methods of physical failure analysis (PFA). Almost all PFA cases for 20nm technology node devices and beyond require Transmission Electron Microscopy (TEM) analysis. Before TEM analysis can be performed, fault isolation is required to correctly determine the precise failing location. Isolated transistor probing was performed on the suspected logic NMOS and PMOS transistors to identify the failing transistors for TEM analysis. In this paper, nanoprobing was used to isolate the failing transistor of a logic cell. Nanoprobing revealed anomalies between the drain and bulk junction which was found to be due to contact gouging of different severities.

A Sample Preparation on Decapsulation Methodology for Effective Failure Analysis on Thin Small Leadless (TSLP) Flip Chip Package with Copper Pillar (CuP) Bump Interconnect Technology

2014 ◽  
Author(s):  
Gwee Hoon Yen ◽  
Ng Kiong Kay
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Flip Chip ◽  
Fault Localization ◽  
Cost Effective ◽  
Fault Isolation ◽  
Voltage Contrast ◽  
Interconnect Technology

Abstract Today, failure analysis involving flip chip [1] with copper pillar bump packaging technologies would be the major challenges faced by analysts. Most often, handling on the chips after destructive chemical decapsulation is extremely critical as there are several failure analysis steps to be continued such as chip level fault localization, chip micro probing for fault isolation, parallel lapping [2, 3, 4] and passive voltage contrast. Therefore, quality of sample preparation is critical. This paper discussed and demonstrated a quick, reliable and cost effective methodology to decapsulate the thin small leadless (TSLP) flip chip package with copper pillar (CuP) bump interconnect technology.

Solving the Voltage Contrast on Floating Substrate with Standard FA Toolset

2016 ◽  
Author(s):  
Julien Goxe ◽  
Béatrice Vanhuffel ◽  
Marie Castignolles ◽  
Thomas Zirilli
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Sample Preparation ◽  
Failure Analysis ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Silicon On Insulator ◽  
Mixed Signal ◽  
Voltage Contrast ◽  
Scanning Electron

Abstract Passive Voltage Contrast (PVC) in a Scanning Electron Microscope (SEM) or a Focused Ion Beam (FIB) is a key Failure Analysis (FA) technique to highlight a leaky gate. The introduction of Silicon On Insulator (SOI) substrate in our recent automotive analog mixed-signal technology highlighted a new challenge: the Bottom Oxide (BOX) layer, by isolating the Silicon Active Area from the bulk made PVC technique less effective in finding leaky MOSFET gates. A solution involving sample preparation performed with standard FA toolset is proposed to enhance PVC on SOI substrate.

Impacts of Sample Preparation Methodology on TEM Failure Analysis of Advanced Semiconductor Devices

2011 ◽  
Author(s):  
Yongkai Zhou ◽  
Jie Zhu ◽  
Han Wei Teo ◽  
ACT Quah ◽  
Lei Zhu ◽  
...  
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Case Studies ◽  
Thickness Measurement ◽  
Interface Roughness ◽  
Silicide Formation ◽  
Cross Sectional ◽  
Inspection Method ◽  
Low Mass

Abstract In this paper, two failure analysis case studies are presented to demonstrate the importance of sample preparation procedures to successful failure analyses. Case study 1 establishes that Palladium (Pd) cannot be used as pre-FIB coating for SiO2 thickness measurement due to the spontaneously Pd silicide formation at the SiO2/Si interface. Platinum (Pt) is thus recommended, in spite of the Pt/SiO2 interface roughness, as the pre-FIB coating in this application. In the second case study, the dual-directional TEM inspection method is applied to characterize the profile of the “invisible” tungsten residue defect. The tungsten residue appears invisible in the planeview specimen due to the low mass-thickness contrast. It is then revealed in the cross-sectional TEM inspection.

Sign in / Sign up

Export Citation Format

Share Document